Screen Blacks Out When Composing Email

When I am composing emails after a minute or two the screen goes black, and the phone reverts back to the home page. The pending email disappears (not even saved as a draft) anyone have a clue how to fix this?

I'll be honest.  These are WAGs.  However...
Since the Reset didn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
Finally, if the Restore doesn't work, let the battery drain completely.  Then recharge for at least an hour and Restore again.

Similar Messages

  • G580- Screen blacks out when power supply is not plugged in to the laptop

    My laptop is just 3 months old and I am already having problems with it.
    The laptop screen blacks out when i remove the power supply from it.
    When plugged in , it starts workin again.
    Whats the point of a laptop if i am not able to use it without plugging in??
    I don kno what the probelm is. Can anyone help here pls...
    Cheers
    Vaish

    Hi Vaish,
    I’d like to help you with this issue as we can try to increase the Brightness of the screen from the power options while plugged in,
    And then please if still the same we can try to uninstall the Lenovo Energy management and reinstall it back:
    Lenovo Energy Management for Microsoft Windows 8
    Lenovo Energy Management for Microsoft Windows 7
    Hope the information helps. Let us know.
    Regards
    Soha
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Screens black out when starting program

    I don't know where to ask this since it is more related to CS4 in general. I mostly use InDesign, but the two moderators on that forum are trolls. I hope it's better here.
    All screens black out for few seconds while starting or closing the following in Adobe CS4:
    InDesign, Fireworks, Bridge, Device Central, Media Encoder
    This does npot happen with other programs I've found or other programs in the CS4 suite.
    Don’t know if this is a software issue or a graphics issue. Everything still works, but it's very annoying.
    System
    i7 processor
    Win7 64 bit
    Quadro NVS 450 graphics card
    Three NEC EA190M monitors
    8Gb memory

    Black screens are a well known Windows 7 problem.
    http://www.ghacks.net/2009/12/01/windows-7-black-screen-of-death-fix/

  • Second screen blacked out when full screen with dual displays

    I have a MacBook Pro connected to an LCD display. I use both screens. When working from home I'd like to have my local machine showing on the LCD monitor and my work machine showing in the MBP screen. I can do this, however I can't have the work machine in full screen mode because ARD blacks out my main LCD monitor. This frankly drives me nuts as there doesn't appear to be a preference within ARD to change this.
    iTunes does the same thing. If I want to watch a video full screen in one monitor it blacks out the other. C'mon Apple, Quicktime doesn't do this and has a preferences tab just for display settings!
    Does someone have a suggestion, work around, or want to point me to what I might be missing to solve this issue?

    I understand what you are doing, but when you are running as full-screen the second display is blacked out because your making your station only the target at that moment. You are telling ARD that you want nothing to do with your Admin station. Also because the target doesn't have a second screen, your is blank. This avoids any confusion as to what screen belongs to what machine. ARD is working as it was designed to.
    iTunes does the same thing to hid extra screens that are not part of the presentation so they don't detract from the show.
    With your Observe or Control in Windowed mode, make the window of you client to fill the display as much as possible. This is the best you can do. Besides, when you are Controlling a client in Full-Screen, you can't move files and such with drag-n-drop. So if you want to work on both at the same time, you need to stay in windowed mode.
    If you would like to make the petition to have your idea supported, do so here

  • S200 screen blacks out when lid opened; lid closed it turns on!

    This is badder than bad for a problem. When I open the netbook lid, the screen blanks out. This even happens at the boot stage immediately after pressing power button, so that the BIOS screen goes black when I open the lid. On closing the lid though, hey, the screen turns on. If it manages to boot the OS and I open the lid, the screen will black out. Then I close it and it turns on, but often opening it again and the netbook sleeps. A while ago, after that stage of the netbook sleeping, I could open the lid, hit Enter and get it to wake up and then I had roughly 1.5 min to do some work - perhaps longer I didn't actually time it. Now, however, it blacks out again after wake up (and its very hard to shut it down using a pencil reaching the power button!) I've opened the back off the netbook and try to find the lid switch, but I'm still not sure where it is - so that I could disable it completely. I'd prefer not to take it to the service center as warranty is over and I already had a $50 repair with Lenovo, so doing it once more is not really worth it. OS is Linux Ubuntu - and in all the Power settings I set it to do nothing when lid is closed. Any help would be appreciated!

    Well, I had the idea of using a magnet to find out if the S200 uses a magnetic lid switch.
    I ran it around the edges of lid and outside of keyboard and front... and suddenly, just by the Backspace key it was, the screen came back to life!
    As i had the case opened I looked at what part was inside just there, and its the small usb/card-reader board.  I couldn't tell if there was a lid switch component there though - but after I touched a few parts there, now the screen is always on when i start the netbook.
    my other problem now though is that half of the keys don't work - no output on screen.
    so that's another issue!

  • IMac screen blacks out when lowering brightness?

    iMac 27" mid-2010
    If I lower brightness, after a short while screen cuts out - computer works fine in background.
    When I am on highest brightness - everything is fine...
    Does anyone know what is happening here?

    Further details:
    27' iMac mid-2010
    3.2 GHz Intel Core i3
    8 GB 1333 MHz DDR3
    ATI Radeon HD 5670 512 MB
    OS X 10.9.1 (13B42)

  • S210 screen blacks out when AC adapter removed

    New problem with my S210.
    When i have it connected to AC, works as normal. 
    when AC adapter removed, the screen alone loses power. (computer does not turn off or go to sleep).
    simply re-inserting ac adapter re-powers the screen immediately.
    this issue does not allow for me to work without ac adapter.
    any ideas if there is a setting that needs to be changed, or if this points to a hardware issue would be appreciated.
    (no modifications done to this laptop, its running windows 8.1)
    thanks

    hi scolello,
    Welcome to Lenovo Community Forums!
    Access the Power Options through Control Panel,
        - Click on the Change Plan Settings on your selected Plan.
               - Now make sure that the brightness are Equal on both Plugged in and On Battery
                        Then Click on Save Changes
    Hope this helps
    Cheers!
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Ver 10.0.1.  Entire screen blacks out for a few seconds when scrolling.

    I recently updated to Reader X 10.0.1.  Now when I scroll through a large document my entire screen blacks out for a few seconds.  So far it has recovered.  I get an error message saying that the NVidia nView driver (ver. 135.50) has stopped responding.  I am running Windows 7 Pro on an HP Laptop, feeding to a large Samsung monitor.  Never happened prior to this update.  Any fixes/ideas?

    You are still under warranty.  Call Apple Care. Make sure you get a case number as all repairs have an additional 90 days of warranty. 
    #1 - You have 14 days from the date of purchase to return your computer with no questions asked.
    #2 - You have 90 days of FREE phone tech support.
    #3 - You have the standard one year Apple warranty.
    #4 - If you've purchased an AppleCare Protection Plan, your warranty last for 3 years.   You can obtain AppleCare anytime up to the first year of the purchase of your computer.
    Take FULL advantage of your warranty.  Posting on a message board should be done as a last resort and if you are out of warranty or Apple Care has expired.

  • Black out when screen is moved

    My screen blacks out at times when I move the screen tipping forward and back. There is only a few positions where it will stay on. It's a 2008 black macbook running 10.7.5 and 10.6.8  Everything else is fine. Hardware test shows no problems. Any idea what kind of a repair this would be.
    Thanks for any repley
    Paul

    The symptom is classic of a broken inverter cable. The cable routes through the left hinge to the screen and wears out from opening and closing the screen. It's a difficult repair but following the guide at iFixIt if you have the courage and patience you can do it yourself https://www.ifixit.com/Guide/MacBook+Core+2+Duo+Inverter+Cable+Replacement/4772

  • Screen doesnt get blacked out when on call after the new update

    Since the time i Have updated the firmware screen doesnt gets blacked out, when on call after the new update. Because of this option automatically get selected by getting touched cheecks.
    any solution?

    Please try to update your plugins [http://www.mozilla.org/en-US/plugincheck/] Flash is out of date.
    Also the Reset Firefox feature can fix many issues by restoring Firefox to its factory default state while saving your essential information. <br>
    '''Note''': ''This will cause you to lose any Extensions and some Preferences.''
    *Open websites will not be saved in Firefox versions lower than 25.
    To Reset Firefox do the following:
    '''For Firefox versions previous to 29.0:'''
    #Go to Firefox > Help > Troubleshooting Information.
    #Click the "Reset Firefox"[[Image:Button reset]] button.
    #Firefox will close and reset. After Firefox is done, it will show a window with the information that is imported. Click Finish.
    #Firefox will open with all factory defaults applied.
    '''For Firefox 29.0 and above:'''
    #Click the menu button [[Image:New Fx Menu]], click help [[Image:Help-29]] and select ''Troubleshooting Information''.
    Now, a new tab containing your troubleshooting information should open.
    #At the top right corner of the page, you should see a button that says "Reset Firefox"[[Image:Button reset]]. Click on it.
    #Firefox will close and reset. After Firefox is done, it will show a window with the information that is imported. Click Finish.
    #Firefox will open with all factory defaults applied.
    Further information can be found in the [[Reset Firefox – easily fix most problems]] article.
    Did this fix your problems? Please report back to us!
    Thank you.

  • In my macbook pro when composing email it coping into thrash as well so how to stop this ?

    in my macbook pro when composing email it coping into thrash as well so how to stop this ?

    You may have a Bad fan. Make an appointment and take it to the genius bar for an evaluation. It's free, in warranty or out.

  • Random laptop screen Black out / Turn off .

     Hi, 
     first of all my laptop is : HP Pavilion dv6-6160se Entertainment Notebook
    to the problem now
    A few days ago my laptops screen started  out of a sudden shutting down/turning black( no lights at all ). This was happening while using the laptop at random. The screen  had no lights, and if i use a flashlight on it there is nothing. like its turned off completelly.
    Before this happens. Ths behavior varies. Sometimes it flickers from my desktop to a black screen then back on and some times not. Most of the times screen changed to a radom color (green mostly) then becomes black/shuts down.
     NOTE: The laptop keeps runing, i can hear the videos playing so it probably isnt a gpu chip or gpu issue , music and games.
    I searched the web for all kind of reasons that this could happen and tried some of the fixes .
    Here are everything i tried and all or the details i could accumulate in past coupe of days:
    1. If the screen flickers , blacks out and then turns back on i get a message that gpu drivers have stopped working and recovered (  on both amd and intel ).
    2. If the screen blacks out, on rare ocasions if you close the laptop lid and let the laptop go to sleep , when waking up screen works again ( noticable due to screen moving)
    3. I tried installing 4 different drivers all with clear install. ( didn't work)
    4. I tried to  to recover system with restore point. ( didn't work)
    5. I tried to lower the screen brightness. ( didn't work)
    6. tried this trick: 
    Turn off laptop
    Remove battery
    Hold the power buttong for 30-45 seconds
    Plug-in the charger ( dont put the battery in )
    Turn on laptop and see if it works.
    Very Noticable details:
    7.  Since  on of the rare fixes requires to move the lid  i tried shaking the screen a bit or pushing it slightly to different directions. This actually  does the trick and turns the screen back on ( i am right now typing  this after using this "trick"
    So, with this one as a hint there are a couple of stuff i have in mind but i am not sure  and need help since i am not a technician.
    a) There is a loose LCD cable and when i type a little vibration moves it and ends up in a black screen.
    b) I read that if you use a flashlight and you cant see  your desktop it means its a bad inverter.
    c) Can the inverter have a lose cabe instead of the lcd ?
    That's all the feedback i could give you that i can recall now.
    Currecntly the screen looks ok ( maybe its the certain angle it has after i moved it  so i would aprecciate a fast reply before  it goes black again
    EDIT: Tried to play a game for a few mins and i got the black screen again. Closed the lid  so the laptop goes in sleep mode then opened it and it worked. Just for the records.
    EDIT#2: Just tried to play a game again. got the blackscreen, shaked the screen a bit and it worked but for the 1st time i get the message " Application has been blocked from accessing graphics hardware" , Can it be that its the GPU after all or maybe drivers? 
    EDIT#3: Tried to play a game again and it seem to trigger the issue . ( i am currently running the laptop with only the intel drivers installed)
    thanks in advance
    Sincerely,
    Ntas
    P.S. Please feel free to ask me any question if you need more information, i am not a laptop expert but i know   more than the average person
    This question was solved.
    View Solution.

    Hi @Ntas 
    I have read through your post and it seems there are a couple of possibilities, and I noted that you have already tried several of the things I would normally suggest.
    I will however post some of those links anyway for you to review, it is always possible there may be something in one of them that may have been missed or may inspire an idea of the cause. Since you mentioned that sometimes just moving the screen will cause the problem or make it disappear, that does seem like either a loose connection or maybe something like pressure on a part of the display causing the issue.  Of course that last part may just mean the display is on its last legs, but hopefully not.
    First I will give you a link to the service manual, to help you check the connections. Just be careful to read the sections on precautions, to protect yourself and to prevent any other damage.This manual is also useful in that it lists all the compatible parts, so if the display is defective you could use this guide to help order a compatible replacement if you choose to do so. HP Pavilion dv6 Notebook PC - Maintenance and Service Guide
    Here are some other sources, that may be helpful to you.
    Resolving Problems with Notebook Displays (Windows 7 and Windows 8)
    Diagnosing a Liquid Crystal Display (LCD) for Damage
    Also for your convenience here is the drivers page for your notebook.
    HP Pavilion dv6-6160se Entertainment Notebook PC Drivers
    I hope this all helps.
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • I dropped my ipad and the screen blacked out and could not be turned on even after pressing the sleep and home button

    I dropped my ipad and the screen blacked out and could not be turned on even after pressing the sleep and home button.
    I tried connecting the device to my computer and itunes said that it could not identify my device.

    What to Do When Your iPad Won't Turn On
    http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
    http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
    iPad: Basic troubleshooting
    http://support.apple.com/kb/TS3274
     Cheers, Tom

  • Attachments not showing when composing emails

    Hello.
    For some reason I don't know, Mail has suddenly stopped displaying attachments I insert when composing emails. No matter what file type, it displays the Lego cube with the question mark instead of the attachment. (Note: NOT the little blue square with a question mark which indicates a file missing etc.)
    However, people receive them just fine and I receive attachments just fine myself. I also receive my own attachments when I send an email to the office mailing list (which includes myself).
    It is only when I compose an email that I am not seeing the things I attach. Not the correct file icon, not the file name or size, not the 'show attachments as...' option. Nothing. Just the blue Lego-type cubes with the question mark.
    I have set the Preference in Composing to Rich Text, we use an IMAP server in the office but I am the only one suffering this problem and I don't know what has changed as it was working just fine until a few weeks ago!
    Any help would be appreciated as it is extremely irritating, if anything because I don't know why.

    Hi,
    What if you do a All Mailbox search, are you able to see the specific mail item in the result list?
    You might need to check your view setting of that folder. Maybe you have it set for unread mail only, or some settings are filtering out the messages you just moved.
    Just highlight the folder, then click View in the ribbon, then click
    View Settings. Click Filter... button on the dialog, then clear any related settings or click
    Clear All button.
    Thanks,
    Ethan Hua CHN
    TechNet Community Support

  • Windows XP mouse halted and screen blacked out!

    When I boot up with boot camp and dragging some windows size (like IE or Excel). The mouse pointer halted and after a few seconds the screen blacked out just like the machines is turned off. However, I discovered that the system is still running. I can perform the shut down action by input from the keyboard.
    The problem does not exist when I start windows xp through VMware Fusion.
    Did anyone encounter the same problem??
    I just bought the iMac a few days.

    Thanks for your reply, I have a wireless mouse/keyboard & called manufacturer to test both & they told me to plug the wired ones in & they did not work & the laptop has no plug for wired ones because those have rounded ends, laptop has wrong size/shape usb ports, so there is no way to test them on laptop, so now I'm hoping you or someone has an idea of what to do next, thank you for your ideas.
    Teddy2014 wrote:
    had the same issue, un plugged mouse, reconnected in another port and it worked. Bought another mouse, all is well

Maybe you are looking for