Screen Brightness on iphone 4s

My iphone 4s has had a problem after i upgraded to ios 6 , the screen can be at one moment fully readable with the adjustment on brightness set to the middle ,,and then its light is off , checking the brightness its reset itself to no brightness , this happens with the auto switched on or off , i have hard reset the iphone , used itunes to do a restore and have set it up as a new iphone but the problem will not go away. Even on the charger i have the brightness set to mid way and when i take the phone off the charger the brightness bar moves to no brightness , i have one time had the screen on the brightness settings and watched the brightness bar lower to no brightness , this is with the auto brightness option switched off , this also happens with the auto brightness switched on as well.
All these problems happened after upgrading to ios 6 , the one thing i did notice after the first upgrade was the screen itself had a higher brightness than before , now the phone mostly sits at home as i cannot use the iphone as the screen brightness changes so much its become a pain to use , so i have to use my wifes samsung galaxy s3 , any ideas on how to sort this problem out or is it a trip to the apple store to get a new iphone 4s ?

I've upgraded to iOS 7 and I have the issue on an iPhone 4S. I can't remember this happening on iOS 6, but there may have been one or two occassions where it did. So, with regards to Julia98765's post above, in my case it just got a whole lot worse with iOS 7, much as I love everything else about it!
The screen starts off on my normal brightness level (auto is off), and then anywhere between a few minutes to just a few seconds, the screen goes totally dark, like it has been slid to the minimal brightness setting. From then on, the screen fluctuates wildy, sometimes snapping back to full normal brightness, but mostly just dim flickering until it decides to settle down in its dim state, or if it has been locked for a few minutes by which time it is showing normal brightness levels again.
Then the whole thing repeats itself. This happens in one form or another pretty much every time I use my phone! The only thing I haven't tried yet is restoring the phone through iTunes so will give that a go and report back soon.

Similar Messages

  • Screen brightness problem iphone 5 ios 6.1.4

    The screen will quasi-randomly go to low brightness and be barely readable - auto-dim or not.  I can't usually tell what triggered it - it's just not obvious.
    However, I found a repeatable pattern (finally) when using it in a car.  If I plug in the usb in a car (say a ford), and use both google maps and play tunes or podcasts simultaneously, the brightness is guaranteed to dim after approximately 20 minutes, on its own, without intervention.  The auto-brightness switch has no apparent effect on this. 
    This is, of course, the most annoying defect, because you're using google maps to watch where the f*@k you're going, and then the lights go out and you're fumbling around with brightness while driving.
    Anybody else observe this problem?

    It's a google maps app setting. I agree, it is highly annoying and I have no idea why they put that setting into the app without the option to change it. I did a 600 mile trip with google maps and the auto screen dimming feature was awful.

  • How do I get my screen on the iphone 4 to be brighter?

    How do I get my screen on the iphone 4 to be brighter?

    You can also slide up from the bottom edge of the screen to reveal the Control center. Slide the brightness slider to the right.

  • IPhone Screen Brightness

    I don't know if anyone else has noticed it, but it seems like different iphones have different screen brightness. I compared my iphone with some iphones in the apple store and the screen was quite brigther at the max setting. Then I compared it with another person's iphone and my screen was slightly dimmer, or more "saturated" in color. Now, I have no problems with my screen. It is bright enough, but it just seems odd that the brightness of the screens is not the same throughout. Are my eyes are playing tricks on me or is this something that some of you have also observed?

    Your absolutely right I have also notice several differences in some iPhones. For example, the two that I have purchased a month apart from each other are dramatically different. I don't know how it happened but the one I got at launch had a soft screen that left discoloration marks, similar to a standard LCD screen, when a little finger pressure was applied. The battery life indicator rarely reached full charge. Additionally, the multi-touch grid points can clearly be seen behind black backgrounds i.e. the home screen. I also experienced glitches with the unit from day one. Mainly application hang-ups which left me little choice but a hard reset. A total of 16 hard reset since June 29. After attempting the software update (which I thought would cure all ills) earlier this week, the unit hung up on the boot logo for good. So after 30-days with this unit I returned to the 5th Avenue and asked that the unit be exchanged. They said no, they could only send it out for repair. I simply reasoned that it was illogical to repair an already defective item. The manager agreed and kindly swapped the unit for me.
    All I could say is...Wow! I didn't know what I was missing. This new unit has a hard screen with no grid points, battery OK, Apps seem to be more responsive, and no hang-ups so far. Good luck to all.

  • Iphone 6 screen brightness problem

    hello everybody, i have iphone 6 which i am using now for 2 and half months. just from 1 week ago my iPhone 6 screen suddenly goes dim when I'm using it in strong sunny light. i always set my auto brightness on and when i use my phone in sunny light at roof first it gives clear and bright display then suddenly screen goes dim and when i try to maximise brightness level nothing happens it still remains dim and i notice my screen becomes very warm .. then i turn off my phone for few minutes and turn it on the screen brightness again works fine...and auto brightness also works normal..i have noticed this problem 2,3 times whenever i use it in sunny light at the roof..plz give me any suggestion....
      iphone 6, 64 gb model iOS version 8.1.2

    It's a google maps app setting. I agree, it is highly annoying and I have no idea why they put that setting into the app without the option to change it. I did a 600 mile trip with google maps and the auto screen dimming feature was awful.

  • Q10 screen brightness is very dim in dark environmen​t

    In a dark environment the screen dims so much that reading text on a white background is terrible.  Is there a going to be an update to stop the auto brightness feature?

    You're not the only one. This is a severe issue that will hamper sales for sure. The BlackBerry Q10's maximum brightness is the DIMMEST out of every other phone on the market today.
    IN FACT, the maximum brightness on the Q10 is 22% the maximum brightness of the iPhone 5 (in lumens): http://www.computerbase.de/artikel/handys/2013/bla​ckberry-q10-im-test/3/
    BlackBerry is already getting a ton of flak for this issue, as many, MANY users are furious. See this comparison with the Bold 9930: http://forums.crackberry.com/blackberry-q10-f272/v​ery-dull-screen-brightness-level-q10-808915/index5​...
    There is also a few news articles circulating: http://www.newstimeafrica.com/archives/31992
    I will be returning my BlackBerry Q10 tomorrow to Verizon Wireless for a full refund. Back to the Bold 9930 until a PROFESSIONAL product is released. I don't even mind straying away from BlackBerry at this point. Not making brightness control available to the consumer is a violation of trust.

  • The screen on my Iphone 5 keeps freezing even after restoring factory settings and downloading latest update.

    Hi
    The screen on my Iphone 5 is consistently freezing.  I have restored the factory settings but that didn't work.  I have downloaded the latest apple update.  Not sure what else to do or if it is a known issue?   It happens on any screen, even the lock screen and the only way to unfreeze it is to press the top button to switch to sleep mode then click the round button and enter in my pin again. Any suggestions would be most welcome!

    Restore the phone as new, and do not restore anything from a backup.
    If the phone still doesn't work properly, you will need to bring it to an Apple store to be evaluated as it most likely has a hardware issue.
    ~Lyssa

  • MacBook Pro 13" screen brightness

    I just bought a 13" MacBook Pro and find the screen brightness and contrast is much less than expected. It basically has to be turned up full on AC to be acceptable, which is very unexpected, since I am typing on a 16 month old MacBook Air now that is about the same at 80% of screen brightness. The contrast is less pronounced on the new machine, too, and the notion of 60% more color saturation seems faulty. I am going to return it and see if the Apple Store thinks this is normal or a faulty screen. Am I being unreasonable to think the new MBP screen should be at least equivalent to the original Air screen?
    Message was edited by: MacBook

    Yes, I agree that there is something different about the two displays. I conducted my own side-by-side comparison -- in the same room lighting, and also switching the places of the two machines -- and found at any given setting, the 13" MacBook Pro was darker than the MacBook Air. Furthermore, when I first started the machine, the MBP's keyboard backlighting would not go off, no matter the lighting. Then, when I went to make these comparisons, the MBP's keyboard backlighting would not come on.
    This linked picture is a composite from two pictures taken in succession in the same lighting and angles, just as they came out of the camera, showing the relative brightness of the two. http://farm3.static.flickr.com/2547/3844348963e76728bce2o.png
    So, I packed up the machine for a trip to the Apple Store and either an exchange or a return.

  • The screen on my iPhone 4 turned black while i was using it-it was not dropped or damaged in anyway. The phone itself is still working as it comes up in itunes when I plug the phone into my computer, but the screen is completley black. What can I do?

    The screen on my iPhone has gone black while I was using it. It just "shut off". The phone is still working  as I can hear/see it when it plugs into the computer, but the screen just wont turn on. I've tried the soft reset "holding down home and lock screen" and i've tried to restore settings. I went to the apple store and they said I had to send it to my provider (in another country) but my phone contract has run out.
    Is there a way to fix this?
    If not, is there some way apple can replace the phone? It's less than 2 years old. Surely the screen shouldn't just give out like that.
    Thank you

    You wrote...
    ' What can I do to solve this'
    What have you tried...?
    The Basic Troubleshooting Steps are:
    Restart... Reset... Restore from Backup...  Restore as New...

  • I resently cracked my screen on my iPhone 4 and had to get a new one... Whe backed the old phone up it didn't save my old apps and now I no longer have that phone...  How can I recover a list of all my apps?

    I resently cracked the screen on my iPhone 4 and had to get a new one... When i backed the old phone up it didn't save my old apps and now I no longer have that phone...  How can I recover a list of all my apps?

    Backup does not include apps,music,vids,etc
    Backing up, updating, and restoring iPad, iPod touch, and iPhone software
    You can loo up your purchases in your purchase history ( in your account in itunes)  and unlike music, you can redownload apps.
    How to redownload purchased apps from the App Store

  • The screen of my iphone is broken and doesn't work anymore. Is there a way to type in my passcode on the computer/itunes?

    The screen of my iphone is broken and doesn't work anymore. Is there a way to type in my passcode on the computer/itunes?

    No, get the screen fixed.

  • Satellite A100 (PSAA9): Win7 + screen brightness adjustment issue

    Hi
    I have installed Windows 7 64-bit on my toshiba A100 (psaa9) machine, and i cannot modify screen brightness anymore.
    It is maximum brightness always. Fn key does not work, and neigther i can modify the brightness manually through nvidia control panel. nvidia driver is 7.15.11.7967, installed automatically with windows.
    In a similar thread http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=182780
    i've read suggestions about Value Added Package to be installed, but there is no package like this for my model.
    how can i fix my problem?
    thanks

    hi all,
    thank you for reply!!!
    ok, i tried to install VAP and Flash Card Utility for Satellite L500. first, installing Flash Card Utility i got invalid serial number error. i've read in forum that it might be due to inappropriate driver for my version on laptop or if i did not install VAP first. so, second, i tried to installed VAP, but i get value "Setup tvap error 0x8146045B" :(
    according my display driver: it was nVidia driver automatically installed with win7. in fact there is no display driver for win7 64bit version on toshiba website... i guess i have more problems with display, as my secondary display blinks every time some system event like driver/program installation or usb device plugging-in or -out happens.

  • Windows 8 Pro Upgrade Problems (Switchable Graphics, Screen Brightness Adjustment, etc.)

    Hi guys! I hope you can help me with this.
    My laptop is a Lenovo U400 bought last April. I upgraded it yesterday to Windows 8 Pro.
    The Upgrade Assistant detected incompatibilities on the following softwares (I'll be mentioning only those I had problems with after the update.)
    -AMD Catalyst Install Manager
    -Catalyst Control Center
    -Lenovo Energy Management
    -Cypress Trackpad
    After the update, the following problems occurred
    -Windows kept prompting me about the incompatibility of Catalyst Control Center and Lenovo Energy Management
    -When I check the Device Manager -->Display Adapters, My AMD Radeon HD 6470M was changed to HD 7400M and has an exclamation point on it indicating a problem. When check Properties it says, "Windows has stopped this device because it has reported problems. (Code 43)"
    -I can't manage switchable graphics because the AMD Radeon driver has been stopped by the OS and Catalyst Control Center doesn't work. It says, "Catalyst Control Center cannot be started. There are currently no settings that can be configured using Catalyst Control Center."
    -My touchpad works but does not support multitouch functions.
    -Screen brightness adjustment stopped working both on hotkeys and Power Options.
    I tried the following actions to fix the problems:
    -Downloaded the new softwares from Lenovo Support but the Catalyst Control Center and Cypress Trackpad still doesn't work. I also tried installing driver software from the AMD site but it still didn't work. [FAILED]
    -I tried to use the Cypress Trackpad software for U300s/e and it fixed the problem with the touchpad [FIXED]
    -Installed the Energy Management software for Windows 8 but when I click the 'Optimized Battery Health' button, it keeps reverting back to 'Maximum Battery Life'. [PARTIALLY FIXED]
    -Resorted to 3rd party software to fix the Switchable Graphics (Catalyst 12.11 Beta from leshcatlabs.net) and it fixed the switchable graphics problem as well as the Catalyst Control Center problem. This is temporary until a working solution or update is available. [TEMPORARILY FIXED]
    -All actions trying to fix the Screen brightness adjustment didn't work. [FAILED]
    Please do help me on this. Thanks in advance!!!

    Yes I own U400 too and I'm using it now. To many forums been read, can't remember which one. Basically, u have to clean AMD and Intel drivers that come along with Win 8. Why? Because the Win8 driver database will lead the device ID "DEV_6760" (if you looking at display adapter device properties) to HD 7400 series instead of HD 6470M, again why? At the bigining only the HD 7400 series already "certified" by Microsoft, while the 6470M out of somewhere. Current CCC (or else) + 6470 drivers, contain also driver for 7400 series in same packages (at least until now, hopefully near future they will release an update). So you can gues where the windows will lead to? Yes 7400 series (certified one). This will explain also why the Energy Management didn't work to= "missing identifier" or we can say "hardware not match".
    You have to find a "fix" driver which contain only HD 6470M and install it manually trhu "Have Disk" option, after you claan all AMD and Intel driver. If you success, then install the CCC from Lenovo Support and from ATI ( I use 12.11 Beta8 Net4 CCC - this is a must), but remember to unchek the AMD Display driver when you install both CCC, and leave the rest checked including Intel Component. Then you can download install anything you want =).
    Leschat's driver did't work on my and "harm" the system. Believe it or not, I found the AMD 6470M standalone driver on HP website. They call it "SoftPack", which actually contain CCC software.
    It's quite tricky thing, that's why not everyone willing to try. But I think it's worth to try, as the risk is not too deep, just backup anything befor you do it. Cheer

  • HT4061 how can i lock my screen on my iphone that was stolen tonite.  i already suspended service to the phone but i want to lock the screen

    how can i lock my screen on my iphone that was stolen tonite, i already suspended the service to the phone, but apparantly there is a way thru icloud to lock screen and when i log into icloud, i do not see the option to select devices.  if so, that is where i can lock the screen, but i can not seem to get to that.
    thanks
    D

    A. Only if the device is online.
    B. Only if you set up Find My Phone before the theft.
    What To Do If Your iDevice Is Lost Or Stolen
    If you activated Find My Phone before it was lost or stolen, you can track it only if Wi-Fi is enabled on the device. What you cannot do is track your device using a serial number or other identifying number. You cannot expect Apple or anyone else to find your device for you. You cannot recover your loss unless you insure your device for such loss. It is not covered by your warranty.
    If your iPhone, iPod, iPod Touch, or iPad is lost or stolen what do you do? There are things you should have done in advance - before you lost it or it was stolen - and some things to do after the fact. Here are some suggestions:
    This link, Re: Help! I misplaced / lost my iPhone 5 today morning in delta Chelsea hotel downtown an I am not able to track it. Please help!, has some good advice regarding your options when your iDevice is lost or stolen.
      1. Reporting a lost or stolen Apple product
      2. Find my lost iPod Touch
      3. AT&T. Sprint, and Verizon can block stolen phones/tablets
      4. What-To-Do-When-Iphone-Is-Stolen
      5. What to do if your iOS device is lost or stolen
      6. 6 Ways to Track and Recover Your Lost/Stolen iPhone
      7. Find My iPhone
      8. Report Stolen iPad | Stolen Lost Found Online
    It pays to be proactive by following the advice on using Find My Phone before you lose your device:
      1. Find My iPhone
      2. Setup your iDevice on iCloud
      3. OS X Lion/Mountain Lion- About Find My Mac
      4. How To Set Up Free Find Your iPhone (Even on Unsupported Devices)

  • [FIXED] after upgrade ACPI can no longer change my screen brightness

    EDIT: never mind, it seems to of gone away now...i have no idea what happened, it stopped working randomly then started working just as randomly.....whatever...
    Just yesterday i was using my laptop with arch linux with the brightness turned all the way down, as of course it saves battery
    but now i turn it on today and the screen is at maximum brightness, and every time i try to change it it just says (in kernel.log) :
    Sep  8 10:28:46 Polygon kernel: ACPI: Failed to switch the brightness
    Sep  8 10:28:46 Polygon kernel: ACPI: Failed to switch the brightness
    so...what got upgraded that broke this? does anyone else have this problem?
    here is the past few days of my pacman.log: (it has some entries for kernel-my, a custom compiled kernel, but i get no screen brightness control on my custom compiled kernel, or the default arch one)
    [2009-09-01 11:24] >>> Updating module dependencies. Please wait ...
    [2009-09-01 11:24] installed kernel26-my (2.6.28-1)
    [2009-09-01 11:25] >>> Updating module dependencies. Please wait ...
    [2009-09-01 11:25] upgraded kernel26-my (2.6.28-1 -> 2.6.28-1)
    [2009-09-01 11:26] >>> Updating module dependencies. Please wait ...
    [2009-09-01 11:26] upgraded kernel26-my (2.6.28-1 -> 2.6.28-1)
    [2009-09-01 11:29] >>> Updating module dependencies. Please wait ...
    [2009-09-01 11:29] upgraded kernel26-my (2.6.28-1 -> 2.6.28-1)
    [2009-09-01 11:30] >>> Updating module dependencies. Please wait ...
    [2009-09-01 11:30] upgraded kernel26-my (2.6.28-1 -> 2.6.28-1)
    [2009-09-01 11:34] removed kernel26-my (2.6.28-1)
    [2009-09-01 11:34] >>> Updating module dependencies. Please wait ...
    [2009-09-01 11:34] installed kernel26-my (2.6.28-1)
    [2009-09-01 11:38] >>> Updating module dependencies. Please wait ...
    [2009-09-01 11:38] upgraded kernel26-my (2.6.28-1 -> 2.6.28-1)
    [2009-09-01 11:40] >>> Updating module dependencies. Please wait ...
    [2009-09-01 11:40] upgraded kernel26-my (2.6.28-1 -> 2.6.28-1)
    [2009-09-01 11:40] >>> Updating module dependencies. Please wait ...
    [2009-09-01 11:40] upgraded kernel26-my (2.6.28-1 -> 2.6.28-1)
    [2009-09-01 11:42] >>> Updating module dependencies. Please wait ...
    [2009-09-01 11:42] upgraded kernel26-my (2.6.28-1 -> 2.6.28-1)
    [2009-09-01 11:46] removed kernel26-my (2.6.28-1)
    [2009-09-01 11:47] >>> Updating module dependencies. Please wait ...
    [2009-09-01 11:47] installed kernel26-my (2.6.28-1)
    [2009-09-01 12:21] installed rsync (3.0.6-1)
    [2009-09-01 12:21] installed abs (2.3.3-1)
    [2009-09-01 12:32] installed nvidia_arch-mark-grandi (185.18.36-1)
    [2009-09-01 13:01] synchronizing package lists
    [2009-09-01 13:02] starting full system upgrade
    [2009-09-01 13:03] upgraded python3 (3.1-2 -> 3.1.1-1)
    [2009-09-02 09:22] synchronizing package lists
    [2009-09-02 09:23] starting full system upgrade
    [2009-09-02 09:23] upgraded coreutils (7.4-1 -> 7.5-1)
    [2009-09-02 09:23] upgraded libarchive (2.7.0-2 -> 2.7.1-1)
    [2009-09-02 09:23] upgraded module-init-tools (3.8-1 -> 3.10-1)
    [2009-09-02 09:23] upgraded raptor (1.4.18-1 -> 1.4.19-1)
    [2009-09-02 09:23] upgraded redland (1.0.8-3 -> 1.0.9-1)
    [2009-09-02 09:23] upgraded syslog-ng (3.0.3-2 -> 3.0.4-1)
    [2009-09-02 12:11] removed kernel26-my (2.6.28-1)
    [2009-09-02 12:30] >>> Updating module dependencies. Please wait ...
    [2009-09-02 12:30] installed kernel26-my (2.6.28-1)
    [2009-09-02 12:52] removed nvidia_arch-mark-grandi (185.18.36-1)
    [2009-09-02 12:53] installed nvidia_arch-mark-grandi_ver2 (185.18.36-1)
    [2009-09-03 10:23] synchronizing package lists
    [2009-09-03 10:24] starting full system upgrade
    [2009-09-03 19:34] synchronizing package lists
    [2009-09-03 19:35] starting full system upgrade
    [2009-09-04 09:08] synchronizing package lists
    [2009-09-04 09:09] starting full system upgrade
    [2009-09-04 12:27] synchronizing package lists
    [2009-09-04 12:27] starting full system upgrade
    [2009-09-04 12:28] upgraded apr (1.3.8-1 -> 1.3.8-2)
    [2009-09-04 12:28] upgraded damageproto (1.1.0-2 -> 1.2.0-1)
    [2009-09-04 12:28] upgraded dmxproto (2.2.2-2 -> 2.2.99.1-1)
    [2009-09-04 12:28] upgraded fontsproto (2.0.2-2 -> 2.1.0-1)
    [2009-09-04 12:28] upgraded videoproto (2.2.2-2 -> 2.3.0-1)
    [2009-09-04 12:28] upgraded xf86dgaproto (2.0.3-2 -> 2.0.99.1-1)
    [2009-09-04 12:28] upgraded xf86vidmodeproto (2.2.2-2 -> 2.2.99.1-1)
    [2009-09-04 12:28] upgraded xineramaproto (1.1.2-2 -> 1.1.99.1-1)
    [2009-09-04 12:29] installed pyxdg (0.17-1)
    [2009-09-04 12:29] installed setuptools (0.6c9-2)
    [2009-09-04 12:29] installed libtorrent-rasterbar (0.14.4-2)
    [2009-09-04 12:29]
    [2009-09-04 12:29] >>> Deluge's daemon is running with the "deluge" user. The default download directory is /srv/deluge/
    [2009-09-04 12:29]
    [2009-09-04 12:29] installed deluge (1.1.9-2)
    [2009-09-04 12:29] installed python-chardet (1.0.1-2)
    [2009-09-04 19:58] synchronizing package lists
    [2009-09-04 19:59] starting full system upgrade
    [2009-09-06 12:47] synchronizing package lists
    [2009-09-06 12:48] starting full system upgrade
    [2009-09-06 12:48] upgraded cloog-ppl (0.15.3-1 -> 0.15.7-1)
    [2009-09-06 12:48] upgraded gnupg (1.4.9-4 -> 1.4.10-1)
    [2009-09-06 12:48] upgraded gstreamer0.10-bad (0.10.13-1 -> 0.10.14-1)
    [2009-09-06 12:48] upgraded gstreamer0.10-bad-plugins (0.10.13-1 -> 0.10.14-1)
    [2009-09-06 12:48] upgraded gstreamer0.10-good (0.10.15-3 -> 0.10.16-1)
    [2009-09-06 12:48] upgraded gstreamer0.10-good-plugins (0.10.15-3 -> 0.10.16-1)
    [2009-09-06 12:48] upgraded libdrm (2.4.12-1 -> 2.4.13-1)
    [2009-09-06 12:48] upgraded libfontenc (1.0.4-2 -> 1.0.5-1)
    [2009-09-06 12:48] upgraded libice (1.0.5-1 -> 1.0.6-1)
    [2009-09-06 12:49] upgraded libpciaccess (0.10.6-1 -> 0.10.8-1)
    [2009-09-06 12:49] upgraded libxau (1.0.4-1 -> 1.0.5-1)
    [2009-09-06 12:49] upgraded libxcursor (1.1.9-2 -> 1.1.10-1)
    [2009-09-06 12:49] upgraded libxinerama (1.0.3-2 -> 1.0.99.1-1)
    [2009-09-06 12:49] upgraded libxxf86dga (1.0.2-2 -> 1.0.99.1-1)
    [2009-09-06 12:49] upgraded libxxf86vm (1.0.2-1 -> 1.0.99.1-1)
    [2009-09-06 12:49] upgraded man-db (2.5.5-2 -> 2.5.6-1)
    [2009-09-06 12:49] upgraded mesa (7.5-2 -> 7.5.1-2)
    [2009-09-06 12:49] upgraded nss (3.12.3.1-1 -> 3.12.4-1)
    [2009-09-06 12:49] upgraded pixman (0.14.0-2 -> 0.16.0-1)
    [2009-09-06 12:49] installed rasqal (0.9.16-1)
    [2009-09-06 12:49] upgraded redland (1.0.9-1 -> 1.0.9-2)
    [2009-09-06 12:49] upgraded xf86-input-synaptics (1.1.2-2 -> 1.1.3-1)
    [2009-09-06 12:49] upgraded xorg-font-utils (7.4-2 -> 7.4-3)
    [2009-09-06 12:49] upgraded xorg-server (1.6.3-4 -> 1.6.3.901-1)
    [2009-09-06 17:54] synchronizing package lists
    [2009-09-06 17:54] starting full system upgrade
    [2009-09-07 12:06] synchronizing package lists
    [2009-09-07 12:07] starting full system upgrade
    [2009-09-07 12:07] synchronizing package lists
    [2009-09-07 12:07] starting full system upgrade
    [2009-09-07 12:07] upgraded alsa-lib (1.0.20-1 -> 1.0.21-1)
    [2009-09-07 12:07] upgraded alsa-utils (1.0.20-2 -> 1.0.21-1)
    [2009-09-07 12:07] upgraded hdparm (9.21-1 -> 9.26-1)
    [2009-09-07 12:07] upgraded usbutils (0.84-1 -> 0.86-2)
    [2009-09-07 13:15] installed gedit-plugins (2.26.2-1)
    [2009-09-07 17:43] synchronizing package lists
    [2009-09-07 17:44] starting full system upgrade
    [2009-09-07 17:44] Install jack-audio-connection-kit, libsamplerate, ffmpeg
    [2009-09-07 17:44] or pulseaudio to get their respective plugins working
    [2009-09-07 17:44] upgraded alsa-plugins (1.0.20-1 -> 1.0.21-1)
    [2009-09-07 17:44] upgraded gnupg2 (2.0.12-1 -> 2.0.13-1)
    [2009-09-08 10:18] synchronizing package lists
    [2009-09-08 10:19] starting full system upgrade
    [2009-09-08 10:22] upgraded fftw (3.2.1-1 -> 3.2.2-1)
    [2009-09-08 10:22] upgraded fuse (2.7.4-3 -> 2.8.0-1)
    [2009-09-08 10:22] upgraded gparted (0.4.6-1 -> 0.4.6-2)
    Last edited by Polygon (2009-09-10 01:51:39)

    Do you happen to know what package broke this? I had this issue a couple weeks ago, and just recently it reappeared.

Maybe you are looking for

  • Error While applying Patch 10.2.0.4

    Hi I am trying to Patch 10.2.0.1 to 10.2.0.4 using the OUI on Windows. I am getting the error "Error in writing to file ORACLE_HOME\odp.net\bin\1.x\odpreg.exe , it is used by another process" and then after i click OK i get "Fatal Execution Engine Er

  • Restored apps not showing in Application Manager

    I did a partial restore using the Nokia Suite, selecting only the "Device settings an applications" content (I wanted to restore a theme that I wasn't able to download again without purchasing a second time). The restoral was successful and I have th

  • No Audio on ANY DVDs!

    Hey, folks... A couple of weeks ago, Emma stopped playing audio on any DVDs. Not just AVIs, mind you, but any DVDs at all, using DVD Player. I've tried restarting, of course, and using different DVDs, including storebought ones. All other application

  • [SOLVED]apps during startx

    i always see 3 terminals and xclock how can i reset the apps running during startx? Last edited by heyya (2009-05-24 09:21:33)

  • How to increase image size, OJ6000n

    I have to print from a PDF and would like to increase the size of the image to make it easier to read. Is there a way?