Screen display and resolution problem

Hello, i have lenovo thinkpad T61 its actual screen is potrait. I installed fresh copy of windows 7 32 bit. All was fine,Display was set according to standard vga driver. But when i installed driver for nivida quadro nvs 140 m display changed from potrait
to landscape. when ever i try to select potrait option and click apply it does changes to potrait but it is rotated to 90 dgrees i dnt know the angle . (i do know about ctrl+alt+arrw keys but they don't work). i also tried changing display from bios
but still nothing. all i get is dual display on the same laptop screen in landscaped mode.i have tried installing windows its get better again but after installing the nivida driver it happens again. let me know if you have a solutions

Can you share the type? Model, type etc.
There can be some settings on the apps, you can also post your question here : https://forums.geforce.com/
Arnav Sharma | Facebook |
Twitter Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members
reading the thread.

Similar Messages

Iphone 6 screen display and brightness problem

hello everybody, I'm an iPhone user and I'm currently using iPhone 6 for couple of months. lastly from 1 week ago I'm having problem in my screen display. i always set my brightness to auto and whenever i use my phone in sunny light which means brightness goes to almost 95% level after using it for a while my display goes suddenly dim and i check brightness level it still is at almost 95% level and when i screw to low level it responds normally but when increasing brightness level it still remains dim then i go inside my room and wait few minutes then again brightness respond normally which means when i increase brightness level it gives bright clear display again.. plz give me any suggestion why is this happening...thanks
iphone 6 , 64 GB, iOS version: 8.1.2

First, reset the phone by holding the sleep and home button for about 10sec, until the Apple logo comes back again. You will not lose any data by resetting, but it can cure some glitches.
If this does not work, and to make sure that this is not software related, set it back to factory settings, without using any backup data afterwards. Set up the rest of the personal settings manually and test the phone.
If the phone works as expected, restore from the latest backup. If the problem comes back, the backup data contained corrupt data, causing your issues.
If it still does not work, this could be a hardware issue and the phone has to be serviced by Apple or an Authorized Apple Service Provider:
Use iTunes to restore your iOS device to factory settings - Apple Support
Find an Apple Authorized Service Provider
iPhone - Contact Support - Apple Support

Messed up color display and resolution because of mini-DVI to video adapter

Once I connected the mini-DVI to video adapter to the tv and got weird colors on my screen for a while but then it worked out, then after a while I disconnected the cable and turned my computer off. After that, everytime I turned my macbook on, the color is fine for two seconds and then it turns into a weird offset color, really bright colors, kinda sketchy and just a few colors, and a weird resolution and display obviously, but then I just connect my Mini-DVI to video adapter and disconnect it again (quickly) and the color returns to normal. How can I make the normal colors stay and not have to connect the mini-DVI to video adapater everytime I want to see the normal color display and resolution??
please help!

Open the Universal Access pane of System Preferences, click on Seeing, turn off the White on Black, VoiceOver, and Zoom options, and drag the Contrast slider all the way to the left. If the issue persists, create a new folder on the desktop, drag half of the items from the Library/Preferences/ folder of the item in the Finder's sidebar with the house icon into it, and narrow down the files until you've isolated the one responsible.
(30807)

Display and camera problems... related?

Dear Folks of Apple Support Communities.
Recently i have started to experience a rather disturbing issues with my screen, and that made me remember of the problems with the camera.
I have MBP retina early 2013 and. well, it is known fact that screens on this particular model are not exactly brilliant... The same could be said about the camera, which has simply tuns of blue noise! But the screen was acting pretty Ok for some time now, there always was a minor image retention, but as i had nowhere to fix this, i had to live with it. But recently the screen started to turn GREEN! Yes that emerald shade, almost like cartoon green!!! That happened to it once before, but was not so intense, well at least i was able to see something... But the other day i was completely blown away, when i turned on my mac and i sew bright-bright green screen with absolutely no picture... Why does this happen to a £2000 product i have no clue! Now it has an uneven colour (the bottom corners are blueish, and the sides are somewhat darker).
Is there some way to resolve it? Or should i ask for the screen replacement (and the camera with it as well)?
I will be in Glasgow starting from september, so i will have an Apple store near by... i just don't want this to happen anymore, it is really scary.
Many thanks . Anna.

Badlydrawnboy wrote:
I have a new MBP that is less than 3 months old. I've been having various display and power problems pretty much since I got it.
You should not be having those type of problems on a brand new Mac. Did you call AppleCare about this? If not why not?
You have 90 days of free phone tech support from Apple on top of your one year warranty. Strongly suggest that you use it before you lose it! You already missed your 14 day from the date of purchase to return your MBP for a refund or an exchange.

Downloaded photoshop elements 12, installed ok and activated, started it and splash screen displayed and app launched then shutdown

Downloaded photoshop elements 12, installed ok and activated, started it and splash screen displayed and app launched then shutdown immediately.
Repeat and crashes again. Help it won't start!

Solved! Tried everything in the support documents and none of it worked. Massive frustration with Adobe Chat staff who know nothing and just kept telling me to look at the support documents over and over. They also gave me a contact number in Australia that has a recorde d message saying the product is not supported! What is that about?
Finally Anand from Adobe tech support called me (from when I reopened the original support case that gave me the serial number).
Just had to rename folder SLCache in c:\program files(x86) and reaccept the EULA and reactive. Now everything works fine. Way to hard.

Newbie PDF screen display/print colour problem

First let me say I've been searching through the forums for an answer for my problem and drawn a blank, mostly I suspect because I'm not exactly sure what the problem is. Also I understand the basics of colour profiles but a large proportion of it goes over my head.
The problem:
Our key "corporate" colour is C0 M100 Y75 K25 - I can get reliable and pretty consistent print colour that I am happy with, across a range of devices from documents I produce in Indesign
For screen output e.g. our website, taking an average of several different devices and monitors (none with any kind of calibration i.e. an average user) this equates to approx R130 G11 B34
I am producing a number of PDF 'factsheets' that will be downloadable from the website and I anticipate that some people will just view these 'on screen' and some will print out for reference.
The problem is C0 M100 Y75 K25 and R130 G11 B34 look radically different when viewed on screen or printed - I almost need a PDF 'screen' profile and print profile within the same document. I know I can get a match on my screen if I calibrate it, but I need it to look more or less correct for anybody who views the PDF.
I hope I've explained this clearly enough and any help or direction anyone can give would be really appreciated!
Thanks in advance

Ahhhh...I see what you are saying now Rob. Unfortunately the docs don't soft proof correctly on my display either - take on board that my display is not calibrated and also I would think 99.9% of the target audience for the PDF won't have a calibrated display either - so I am after a solution that falls to the lowest common denominator.
However, if my understanding of what you are saying is correct, if I had a profile that I could use on my uncalibrated monitor that soft-proofs correctly (more or less - I'm not going for absolute accuracy, just somewhere in the right ballpark), then using the PDF/X4 preset with that profile set would mean others opening the PDF on similarly uncalibrated monitors would also see the more or less correct colours?
Would that profile not throw the colours out on the print if that end user then decided to print it out?
Again, apologies for the simple nature of the questions, but I've only been using InDesign for about 8 months and so far I've lived with the colours appearing wrong on screen as I've known they come out how I expect at print time. This is the first thing I've done where I would like it to look more-or-less correct on screen as well as in print.
Thanks for taking the time to reply, I really do appreciate it

ThinkPad Hotkey Features Integration 3.89.0000 On Screen Display and Mute Button Fail

I am installing updates on a T400 system running WIndows 7 Pro 64-bit.
The system has been freshly factory restored and all features work properly...
After running System Restore to update to the latest drivers and recommended software, I find Thinkpad Hotkey Features Integration 3.89.0000 breaks features.
I am able to use Hotkeys to change brightness up/down, Fn+F5, Fn+F6, etc. The volume up and down keys work to change volume. The mute button does not work at all! There is no On Screen Display to show the adjustment settings for any Hotkeys.
I have found that installing the older 3.88.0000 (8jvu40ww.exe) version of ThinkPad Hotkey Features Integration works successfully with mute button functionality as well as the On Screen Display features.
Comparing what is different between the 3.89.0000 and 3.88.0000 versions, I find On Screen Display version and Full Screen Magnifier have advanced. The version information table at the bottom of the software download page is inconsistent compared to what is actually reported from the 3.88.0000 setup.exe:
Setup shows:
On Screen Display 6.71.00
Full Screen Magnifier 2.40
The table shows:
On Screen Display 6.72.00
Full Screen Magnifier 2.41
The System Interface Driver is 1.05 on all the recent versions.
With the 3.89.0000 version installed, I cannot uninstall and go back to the older version to get it working. Instead, I have to do a System Restore to a point previous to the newest install... something changes in the new version but I am not yet sure what.
I have no warranty on this system. Lenovo technical support is unwilling to entertain a conversation about solving this issue with their software unless I purchase a support package. Perhaps someone from Lenovo reads this forum and/or one of the community members has a contact or option so that I may report the issue to those who are responsible for resolving Lenovo software issues. I am hopeful they can solve it in their next release so that I do not have to hide the current version from System Update.
If anyone has ideas on what causes the latest On Screen Display or Full Screen Magnifier to disable the mute button and prevent On Screen Display from working... I would love to try and solve that problem. Additionally, if you have ideas on what prevents uninstalling and going back to an older version, that would also be helpful as I would not like to rely on System Restore.
If there is no solution other than to avoid 3.89.0000 it is what I will do and this message will help others so they do not spend hours to confirm the issue is with the 3.89.0000 version rather than suspecting hardware issues.
trying to figure out the source of the trouble.
Thank goodness Lenovo offers previous versions in a table at the bottom of the pages so we can try older versions and go back to what works. It is a shame they do not advertise a link or other option to report bugs and issues with Lenovo software/drivers directly.

This is the roulette you play with updating functions that are already working properly.
If it's not broken, don't fix it. Do the release notes describe a fix or enhancement that you want? No? Then leave it alone. Hiding updates in Lenovo Update is the easiest solution. For RChesley, in this case.
Bob, I realize that you want the function that the update is supposed to deliver, but the update has failed you. It's like installing version 1.0.0 of software sometimes, with Lenovo Update. You're never quite sure what you're going to get. There's tons of posts here that read as though the users are beta testers--installing updates and finding the bugs! So the developers can go back to the code and try again.
I've learned to never be an early adopter here.

On screen display and FN+ buttons don't work after format

I formatted my entire HDD and re-installed windows 7 pro. After doing the format and re-install the on screen display doesn't show up when I adjust volume or enable/disable caps lock like it did previously before I re-installed. I've installed the hotkey driver, on screen display, display interface driver, ran the Lenovo update utility several times, installed all windows updates. Is there somewhere where I have to enable OSD (on screen display)? I am sure this is just something small that I am overlooking but if anyone has any help please let me know! sorry if this has been posted already, I tried searching before making a post but didn't have any luck.
T400
Intel® Core™2 Duo T9400 2.53 GHz__Windows 7 Professional__3GB Memory__160GB, 7200RPM Hard Drive__14.1” WXGA+TFT-CFL__ATI Mobility Radeon™ HD 3470--
Solved!
Go to Solution.

A couple other things to check:
1. look in task manager, is TPONSCR.exe and TPOSDSVC.exe running?
2. look in Services control panel, is "On Screen Display" service installed and started?

My MacBook Pro is apparently powered on, but no screen display and cannot power off. Cap lock works so keyboard is working but trackpad not responding.

MacBook Pro is powered on but no screen display. Track pad not working and cannot power off. Have tried wireless mouse and no response.

Bring it to an Apple store or AASP. Power down by holding the power button down.

Screen Size and Resolution on Remote Access Mavericks

Hi Forum,
Accessing my Mac Mini remotely and it has a new install of Mavericks. The Screen size and shape and resolution isn't right, but Screen options in System doesn't give me any options. Is this because, physically, no screen is attached? Do only screen sizes and options come up when a screen is attached?
it currently shows 1280x960 [i think - just turned off the mac to get back to work] or 'scaled to fit'. Neither is right for the MBP remote access,. It was fine before i upgraded.
any ideas?

Hi xerhino, and a warm welcome to the forums!
Good work on your part!
Hope your doing OK with the Snow, Ice, and Winds!

KT880 Slow Screen Draw and other problems

Is there a performance issue with the Kt880 boards that causes it to draw the screen slow, and causes the onboard LAN to fight with the USB controllers?
Do I need to reduce the FSB of my RAM @333 to the FSB of the 2400+ @266?
Maybe there are some BIOS tweaks that fix this problem?

Not sure yet but I think I have sorted out most of the bugs.
Changing the FSB speeds and removing a stick of ram does nothing, except to reduce the system performance slightly.
Updated BIOS to latest. No change.
Repair install after removing Symantec AV 9 Corp, and System Works 2005. helped some.
Removing the NIC, uninstalling all Networking components then putting it all back really made an improvment.
Then I turned on the SATA controller and let it install the PCI to IDE bridges and that helped. Removed the VIA CPU to AGP driver and it reinstalled it's self. slight improvment on the screen draw problem.
Getting the USB to stop messing with the PCI bus was easy. I removed all the PCI cards RESET Bios data, reinstall VIA 4.53, added the PCI cards in one at a time then added on the 2 extra drives. Will change the drives to SATA next week.
I think the whole problem comes from the install CD I made with NLight. Nlight has an option to remove components, turn off SFP and modify the UXTHEME.dll, and the TCPIP.sys file.
After work Monday I will try a fresh install of Win XP OEM original on a spare drive, and update it to SP1, then SP2 and see how it goes.
So far game play is excellent with good frame rates and no crashes. My team mates were complaining of poor frame rates on a custom BF1942 DC Map with frames of under 10FPS where I was at 65 to 100FPS.
That poor KT600 I had was probably fine

Display and Boot Problem with MSI K9NGM2

I recently purchased a system:
- AMD Athlon 64 X2 4200 Core Duo
- MSI K9NGM2
- 1 GB Kingston RAM
- 320 GB Sata seagate
- Sony DVD RW
- 450 Watts Power Supply
The very first day I started having problems with my system. Sometimes it never showed a display and if it does it was not able to recognise my hard disk. I have to reboot it several times before it does. I think its the computer who decides when to boot and when not to. I got it checked and the vendor says that everything is fine , although he is also not able to respond to my problem. The Sata cabling and the Ram has also been replaced twice but still the problem persists.
Does anyone have any answer to this problem.

"PSU Details
+3.3V 10A Orange , +5V 15A Red , +12 V 8A Yellow , -12V 0.5A Blue , -5V 0.5A White , +5VSB 2A Purple"
oh my god
replace that "PSU" mate, (that PSU is directly for trash) get a decent one. (single rail, with high amperes on +12V (30A for example)) avoid noname/unknown,Q-Tec,Codegen brands
Good PSU Recommendation:
https://forum-en.msi.com/index.php?topic=103299.msg757739#msg757739
Add-on to read:
PSU's---2 x 12v---The Dual Rail Myth
Is your problem caused by your PSU?
good suggestion can be found here:
https://forum-en.msi.com/index.php?topic=105635.msg783148#msg783148
https://forum-en.msi.com/index.php?topic=103299.msg757739#msg757739
Good PSU vs Cheap/Unamed/Budget PSU Oscilloscope scan:
Bad PSU:
Quality PSU:
Cheap PSU Codegen 350W:
Enermax 365EG(350W):
What would happen if your PSU can't cope with the load?
* bad 3D performance
* crashing games
* random shutdown
* spontaneous resetting PC
* freezes during gameplay
* PSU overload can cause it to break down

My Iphone 3g stays in the maximized screen display, is this problem common and correctable and how?

While listening to an mp3 through Safari, I had the screen expanded to accommodate reading the page. I shut down, left it on charge. The next start up all screens were at Maximum size. There is a momentary flash at the normal size and then expands to Max.
what to do??
peter.

Zoom feature is covered in the manual
iPhone User Guide (For iOS 4.2 and 4.3 Software)

Screen size and resolution mismatch after 2008-008 update.

This is very odd. My screen is shifting around every time I move the mouse on my macbook pro. It appears that the mac doesn't think the full resolution will fit on the screen, and so shifts a few pixels up (or down, left, right) whenever I move around the screen. It's very difficult to use since it distorts whatever I'm reading. I've tried selecting different display resolutions: 1440x900, 1280x800, & 1024x768, but the problem persists even on lower resolutions.
Could be a red herring, but I've checked the install.log for errors and found a couple instances of this sequence:
Dec 22 07:42:04 gseven : update_prebinding[25268]: update_prebinding: too many errors (101)
Dec 22 07:42:04 gseven : update_prebinding[25268]: update_prebinding: error: terminating
Dec 22 07:42:04 gseven : update_prebinding[25268]: update_prebinding: error 256 running updateprebindingcore
I don't know if that could even be related. Anyway, does anyone have an idea how to fix this?

Hi xerhino, and a warm welcome to the forums!
Good work on your part!
Hope your doing OK with the Snow, Ice, and Winds!

Ideapad u410 display and suspend problem

Hello,
My Problem is, that when I close the lid of my ideapad u410 it suspends, but when I open it again it sometimes works as expected, but most of the times the screen is displaced. (Everything is moved about 500 pixels to the right and a bit upwards too.)
For now I have set my laptop to completely shutdown when I close the lid, which works fine, but I would really prefer to get proper suspend working.
I also experienced this displacement once or twice when booting the laptop normally.
this is the output of xrandr
Screen 0: minimum 1368 x 768, current 1368 x 768, maximum 1368 x 768
It's weird because the actual resolution of my screen is 1366x768, and I noticed that when I move my mouse to the left or right border of the display, the screen actually moves these 2 pixels to the left or the right.
This might be a whole other problem, but they could be connected too, I guess.
Info of lspci | grep VGA
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
01:00.0 VGA compatible controller: NVIDIA Corporation GF119M [GeForce 610M] (rev a1)
I am currently using the nouveau driver.
Another problem I noticed, that might or might not be connected to the first two, is that I can't change my tty.
When I press ctrl+alt+Fx the screen just goes blank and I can't even change back to my previous session.
(Usually to get the function keys on an Ideapad u410 it is necessary to press the Fn key, but I changed that bios setting.)
If further information would be helpful, tell me what you would like to know.
Thanks in advance and a nice weekend,
Alfred

So, nobody knows what to do?
Or is it just a problem that can't be fixed?

Screen display and resolution problem

Similar Messages

Maybe you are looking for