Screen Freez (memory expert needed) P6N SLI platinum

on my pc when i install the first two ddr2 800 and one ddr21066 everything is fine but when i install the fourth ddr21066 the system either freezes at boot up or while doing something. can any expert in memory tell me which setting in bios i have to adjust so i do not get this freeze up (mouse andkeyboard) , your comment will be much appreciated.(this is definitely a memory related issue)
MSI P6N SLI Platinum
Q6600
MSI 256 graphic card ATI HD 2400
2 GB crucial DDr2800 CL6 and two DDR2 1066 CL5
mastercoll 500Watts
window xpsp2

im with Jack and MSI doesnt support 1066MHz on the P6N SLi Plat.
Read here:
http://global.msi.com.tw/index.php?func=prodmbspec&maincat_no=1&cat2_no=&cat3_no=&prod_no=1140#menu
Fifth line from top, 800MHz is max.
And yes i know it says so on the box, that 1066 is supported, but it isnt.
But if you think you'll have a faster computer, well it isnt noticeable, that is if you have any gain, cause usually those high MHz DIMM's are on higher latencies then lower MHz DIMM's. If you gain anything its a few nanoseconds we are talking about here.
For instance 1066MHz 5-5-5-18, is as fast as 800MHz 4-4-4-15
Also DDR2 1066MHz is usually overvolted 800MHz memory and thus will have a shorter and sometimes more unstable lifespan.
Furthermore if you use 4 sticks-o-ram on this board, your limited to 667MHz, otherwise your memorycontroller would be overflooded with too much data.

Similar Messages

What the most stable quality 4gb (2x2gb) memory for the P6n SLi Platinum?

Hi,
I'm looking for the most stable and very good quality 4gb of ram for the P6N sli platinum MB - what make does everyone recommend for this board?
I note that Kingston value ram is mentioned on the Approved list but I wanted something faster than the valueram?
Does anyone have either G.Skill or super talent and if so how do they work? Any other makes that you can recommend?
I know that there have been issue swith 4gb of ram for Xp/Vista 32 bit systems but from what I am reading hopefully the next bios should resolve this ...?
Thanks as this is the only item that's holding up my build now !

I don´t know whats the most stable 4GB solution is, I only can tell you, that I use Micron/Crucial mamory for years and never had any problems.
Actually in my new P6N-SLI Platinum are working 4 1GB dimms of crucial value ram ddr2-667 without problems.
There is a new bois version 1.22 for the platinum which solved the 4GB problem of earlier bios versions.
That was a bios problem and not a problem of the ram.
Manufacturer as Gskill on their GBHZ6400 modules and OCZ on their 1066 SLI modules are using the same Micron chips called D9GMH which are on my values.
They have great potential above the rated 667 speed. Cause i´m coming from germany and at the moment the prices of memory here are very cheap, a lot of people are thinking about upgrading their memory.
All what I read about here in germany G.Skill, Mushkin(very expensive), OCZ, A-data, TeamGroup are the most reliable rams
when it comes to high speeds and low latency modules.
At least I recommend the Crucial Ballistix ddr800 if you are not able to handle special settings in the motherboard bios.
And of course there are coming 2GB modules from most of the manufacturers, so you only need 2 modules for 4GB.
It´s your choice...
greetings from germany
gonzos-revenge

[P6N SLI Platinum] black screen NO BOOT after D-bracket replug [RMA-SOLVED]

Quick setup specs;
P6N SLI Platinum
E6600 (box/stock 2400mhz basic)
2x 1Gb DDR2 6400 Gskill HZ
Sapphire ATI X1600Pro (PCI-e basic)
Aerocool Zero DBA 620W
(2 HDs sata, 2 Hds pata, 2 optical pata at first -all OK at first, disconnected after, so irrelevant here ,( )
(XP Pro clean new install from start)
I tried to check the forum old posts before trying to write that new one, but could not find any really related totally adequate posts so far (or i missed them, sorry if so, then -?). I could already find very useful informations on first aid usual 'rebooting' procedures to follow with minimum new boot configurations, d-bracket new LED signals etc. But so far no luck, all same, nothing better, nothing cured here for the stuation here. ,(( Also excuse my english if not perfect, i am not english either. ,(
VERY bad & sad problem here... ,(((( :
All was working perfectly great during 5 days.. the P6N SLI platinum install went GREAT initially (as normal, not a first pc built, all normally happening, so far so good, etc).... all hardwares compatible together at first (dedicated ATX 'full' 8x8 pins connector too for the cpu only for ex -all working perfect at first try. quick tensions 5V/12V under msi dual core control tool perfect too etc), was great easy going/ great strong ultra-stability feeling on the hardware side.. i was just now concentrating on the software side (no special BIOS tweaks even attempted so far, all on basics-normal e6600/ddr2 auto-settings, apart at the end ddr2 quick test -when problem occured- on 450(900?)Mhz at 2.1V, far far easy under its possible specs max anyway.. and had been working perfect for 3 days with that little ddr2 boost try -no time for special bios further tweakings now, etc), reinstalling and transfering/reorganizing slowly my necessary files/hds/softwares from old to new setup, no oc, nothing special tempted (i was planning oc, new cpu more suited fan/silver6 etc only for the end..), LAN file sharing setup done, Realtek audio setup test done, etc ; installation had been so far one of the quickest and problem free ever... explaining maybe also my fatal lack of cautioun for just (too much) 3 sec in the end after 5/- days of perfect working new ring going on.. ,((( :
At first, i also tried to immediately install the D-Bracket too to check possible hardware install problems -very useful feature i of course thought too..and wanted to try too, "in case of"..- (installing it from quick reading of the printed manual..with no colour pic coding inside..and quick error coming from there thereafter with an initial mismatch usb/jbd1 inverted plugs connections.. *both* having the exact same pins numbers and dispositions, beeing side by side on mainboard layout.. and so able to connect both headers indifferently.. so i did not see it immediately (( .. and no way to see it otherwise as such, anyway.. ,( ), just to be sure all was ok. I noticed that LED were of course, never lightning (not normal).. but as EVERYTHING else was working fine (GLAN, sound, etc etc).. i did not bother more than that -- error checking not necessary.
Till that fatal clumsy day i wanted suddenly to.. check the D-bracket too. ((((
All was working well, XP pro opened for hours as usual etc..
i had not yet totally finished to install the motherboard in the pc-case (always on desk, free in sight..)... so i could always see the connections on it. ... and i noticed that ... the colour headers codes were NOT matching (usb=yellow..).. i had just stupidly initially badly connected the D-Bracket jdb1/usb adjacent plugs (inverting them), so... And still, all had ever worked perfect.. except the D-Bracket, of course, was sending back no lights then, obviously.. so i did the fatal error.. confident all was stable enough and strong if even that initial plug error had had no consequences at all.. i did the fatal bad move to try to UNPLUG the D-Bracket connectors and put them back in right orders WITHOUT switching OFF the power supply so... like an hot USB plug, sort of, in a way. fatal error.. :( :( :(
As soon as i began to remove the usb/jdb1 connectors and put them back in normal order... the system suddenly SHUT DOWN ... no special bad noise, no special smell.. just sudden SHUT DOWN.
From there.. impossible ever to boot back again the so far perfectly working machine (((((((((((( , always same till now :
i switch on the power supply.. orange led appears on motherboard (ok)... i switch on the motherboard.. green led on motherboard appears (ok)... CPU fan begins (ok), video fan begins (ok) .... and... NOTHING.. total black video screen. no more even possibility to see the BIOS. :( total dead startup .. and the fans are going on eternally, blocked eternally in that inital startup with leds on too (no sudden shut down after a few seconds.. just.. nothing)... :(
Suprem irony.. the D-bracket LED seems to 'work' now.. "of course". Just the PC no more booting at all ^. Only thing is that only green LEDs are appearing, no red ones... simply the sequence, from start and never changing :
1. GREEN 2. GREEN
3. GREEN 4. (---) (not red, just nothing -?)
If i look in manual, it means "Testing RTC (real time clock)". I don't know exactly what it means *here*, but sounds to me it is the most basic initial first BIOS checking.. and BIOS can't be reached for even that so ; BIOS fried???? :( :(
I tried every 'standard' things recommanded usually here in older posts, for new boots recovery attempts thereafter in such 'boot errors' situations (clear cmos button pushed in every possible ways -quick, long, quick etc..-, removing little by little everything but the very minimal least energy taxing setup; keyboard, cpu, video, motherboard; 1 ddr2 nearest cpu slot.. point).. NOTHING. Worst, i tried to boot with one of those elements missing.. exact same D-Bracket lightning from start to.. eternally (123 GREEN 4-nothing). Even tried to remove the little (cmos?) KTS lithium battery for a few hours -that could work sometimes with the old already ultra-sensitive amd/nforce2 chipset bioses problems, so i tried there too-?-; same 3 green lights and fans running and nothing else happening from there.. ((
Always the same; total dead boot as above. black screen. no possible access to even bios panel. ,(((
So my desperate questions, now: of course, the origin is obvious here; all happened "by my fault" when i tried 'too quickly' to 'hot-plugging' replace correctly the D-BRACKET plugs *without* switching off the power supply... all shut down suddenly when i put back correctly the usb& jdb1 headers... :( ;
- do you think there could be any possible last HOPES to recover the situation that i had missed (a well known situation in such d-bracket handling 'common' (?) connection error, a simple trick to try i had missed ??)
- do you think i FRIED something in the process on the motherboard ?? :( :(
- do you think it is 'only' the BIOS (fried????) ?? :( :(
- do you think i could have fried a specifical external key component in the process (not necessarily motherboard) : ddr2 modules, cpu, video card????? :( :(
- is my only solution is to send the motherboard to RMA (no other ways now) ???
please, don't hesitate to give me any possible hints to try to avoid the RMA process.
can i avoid it, right now?
is that possible to fry an whole board just with such a D-Bracket 'hot plug switch' (on a so far perfectly working -light- setup - no oc, little video card, etc) ???? :( :(
That is the only C2D Intel/ddr2 motherboard i have here around. No possibility to test elements by elements for precise error checking (cpu, ddr2 modules, video card or powersupply).
Only things i could check so far are;
- the power supply (aerocool 620W zeroDBA) ;
i tested it back on my old amd xp-m nforce2 setup.. always working apparently. NOT 'fried' so, apparently. but no way of course to test for exemple the special 8x8 (or 8x4) Intel ATX cpu connector on old xp-m motherboard. But power supply NOt fried at least, apparently -?
- the video card.
no way for me to really test the pci-e card on other motherboard around but.. i tried a very old PCI VGA card.. that one works on old setup.. and on P6N, no effect, doesn't improve the situation. So, not sure the new pci-e video card isn't fried.. but a new video card doesn't correct the dead boot problem.. (
No way for me to test the ddr2 or CPU directly though.
Do you think DDR2 or CPU could have been fried in the process too ???
or just, as i fear anyway, 'simply', the motherboard BIOS fried -??? :-(
Really, thx for any suggestions..
if there could be an 'hidden' trick i did not try yet to try to recover the (initially working perfectly!!! (( ) setup, WITHOUT engaging the motherboard RMA process (at least 2 or 3 weeks lost here to wait the return..online store etc..)....
please, suggest me.. ,((
i am *really* very sad of that stupid clumsy idea to want to 'enable' the D-Bracket.. all was working great so far.. and i lost all with just that stupid idea to try an hot plug bracket reconnection without switching off the power supply it seems.. can it be possible,sigh?? all seemed so stable before that, that i.. just lost my usual cautious just 3 sec too long it seems... :-(
Thanks in advance
hoping post not too long too, but i tried to expose the situation as precisely as possible; first time i ever had such a problem with a motherboard/system install.. that is quiet ironical knowing it was also the best and quickest/easiest easy going new built i ever had so far too.. till then ,( .. and all came from the 'helper' d-bracket 'luxury second hand possible boot helper diagnostic tool' checking in the end too, here.. really hoping i can avoid an RMA process.. and no other hardware elements (apart the motherboard?) could have been damaged in the process ? ,(((

hi, thx a lot for the quick answer. sorry for the length indeed (i did not know exactly how to describe the situation.. without omitting any later possibly important details).
Alas, i already tried that many times in following interesting asnwers on similar problems in old posts here; did NOTHING. ,(
But after your post, i tried it again, and removed for the remaining *hours* (6/8h?) the cmos battery as suggested again *too* so -pushed again the clear cmos button etc when battery out, then when in again, then replugging the powersupply etc; NOTHING better alas too. always same, no boot, black screen, no bios. ,(
Problem always the same, to sum up, for clarity:
power supply on => orange motherboard led is lightning up, motherboard on => green motherboard led is lightning up, cpu/video/case fans are working up as normal and.. that's all. nothing else forever. black screen. no signal. not a single chance to get again the bios setup screen.
another detail i omitted, maybe; keyboard lights are all lightnng up too.. and stay blocked in that state too. tested with 2 different keyboards, same. to shut down the leds, fans etc, only one solution, shut down the power supply button directly, at that stage.
right now, i test on barebone minimal system as recommanded too;
cpu, 1 dimm (closest cpu slot), video, keyboard. all rest disconnected.
i of course tried to reset the cmos with the 'magical red button' many times before, with power supply cable plugged out, pushed the button trying almost every possible way so far (quick, long, long sequences, short sequences etc etc)... changed NOTHING so far -is that thing working?? ,(. and right now, same after hours with cmos battery removed too. ,(
the d-bracket leds are always (now it is correctly plugged..) :
123 GREEN 4 (nothing)
"Testing RTC (real time clock)"
another 'interesting' detail is that; those leds are appearing IMMEDIATELY after the motherboard is switched on, from start (green led appearing on P6N). and it is staying as such till the end. nothing else. i tried to connect also the case speaker ; no bips, no sound signals at all too.
I also remind the system was WORKING like a dream during 5 days *before* i had that sudden TOTAL boot problem.... AND i touched almost nothing in the bios too all along, for initial security reasons too.. (i was concentrating on the software installs anyway right now, NOT on the oc side..). The ddr2 quick little change i did was also the ONLY change i tempted to simply test quickly some setting i already saw working without problem with that P6N and that kind of ram.. and it was working without problem so far too, so.. all the time idem. And it had been perfectly working for 3 days as such untouched from there; no problems at all (those memory modules have been seen on that motherboard largely at those specs, why i did that quick test anyway.. far under their possible max -micron chips). it was even working so well i forgot to put the setting back as default after that quick ram test.. so much it was stable too (even if i had not time to do real memtest test on that one - i did for many hours with the initial automatical default settings too, to check the ram quality, was perfect for many hours, so ok too, no bad ram initially too-; was so stable for all my XP software installs operations etc.. that i forgot it thereafter, to be true..why it stayed like that till that moment (incidently).. but i preferred to mention it 'just in case' though, yes. i also did not push at all the dimm voltages in the process, it was always far inside the specs at 2.05V to be exact -usual for that ram too up to those numbers easy for it. i did not push the ram voltages either so..).
The problem ONLY appears when i wanted to unplug the *initially* badly connected D-bracket headers so (inverted headers.. but that caused NO problems either so far too for the system stability.. only the LEDs were of course not working so far..) : i did the error to NOT switch off the power supply. :(
*then* immediately the system shut down... and above situation appeared. ,(
BUT all was working perfect before.. ram setting included so. ,((
So my simple questions now too ;
- do you know what means *exactly* the d-bracket message 'Testing RTC" (123 GREEN, 4 nothing).. initial bios problem, isn't it?? other ways to recover it now?? ,((
- is it a WELL KNOWN PROBLEM when we try to disconnect and replug too hastily the d-bracket headers without switching off the power supply (*my* main erorr here, it seems :( :( ) ????
... and of course, do you think it could have *fried* another key component (cpu, ram -?? why i reminded the setting, just in case-?-, video card? .. ) with that d-bracket initial disconnection error ... ,(
as i said, i have no secondary c2d/ddr2 motherboard here : no way to test the cpu and ddr2 modules on another motherboard to be sure too here. :( i absolutely can't know if they have been damaged or not, here.. :( :(
any other idea for the motherboard itself though ??? ,(
once again, thx a lot for any suggestions and precisions on that problem (is that a COMMON well known problem with the d-bracket, when we unplug and replug it without extrem care like i did -my main inattention error it seems.. mainly because all was so stable before too.. ((( - without shutting down the power supply/system FIRST ???? can it be possible 'only' that shut down all the system??? (( )
thx in advance again +

P6N SLI Platinum – endless reboot loop. Need help!

P6N SLI Platinum – endless reboot loop. Need help!
Configuration;
Windows XP Pro, SP-2
On old hard drive (Maxtor) I installed in the new case
OCZ GameXStream OCZ700GXSSLI ATX12V 700W Power Supply
MSI P6N SLI Platinum
EVGA 256-P2-N550-T2 7600GT
INTEL Dual Core E4400
MEMORY tried two different ones;
GeIL Esoteria 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400)
Kingston Value Ram 1GB 667MH (of course tried in different slots, stick @ time)
NEC DVD player/burner
Old Maxtor IDE drive W/OS (I have new Seagate serial but won’t install it until I get everything else running.
Computer goes in an endless reboot cycle. First, showing a black screen with small parallel white hash marks. Can pull up Bios but that’s as far as I can go. At first, I thought the high end Geil memory might be at fault. But after installing the more generic Kingston I get the same looping.
In Bios, it is reading all my hardware; CPU, memory, hard drives, temperatures, voltages, etc. the only thing it doesn’t specifically show is the Evga video card. I don’t know if there is really any place it would show except in Hardware Profile.
One other thing, Bios is showing the NEC as the Primary IDE Master and the Maxtor as the Secondary IDE master (although I have tried it both ways). I generally like to boot first from my DVD then go to hard drive.
I don’t know where to go from here. Can anyone give me some suggestions?
Thanks,
Clickman

two replies;
To Vernonion
With JUST new Sata drive & DVD I get message "Reboot & select proper boot device or insert boot media in selected boot device & press a key" in other words, install windows. No flashing anything.
To Maesus
Yes, have tried boot sequence every which way . DVD functions as I ran Memtest for 4 hours last night.
I think I will use the information mentioned in the 3 links V gave me earlier to "repair" the OS on my old Maxtor drive. It is partitioned with OS in one area by itself, docs in another partition, programs another, etc. so I wouldn't lose any work. At worst, I might have to reinstall some programs. At best, I accomplish what I set out to do.
Many thanks,
Clickman

P6N sli platinum + F2-6400PHU1-1GBNR memory from g.skill

So I have a msi p6n sli platinum (650i) and 2 x F2-6400PHU1-1GBNR g. skill memory.
I was wondering what timings / voltages others had reliably attained with the same.

I need to understand the purpose of this thread. It is fine to have general enquiries on the board's combination with other hardwares, but at least provide us more idea of what you are trying to understand.
It'll be good if you can let us know your current config on your current system combination and break the ice from there.

Memory Setting DRAM setting P6N sli platinum

i wonder what setting you would go for the highest cpu GHZ . i have set mine at these and it is 3 GHz , temp 28 degree Centigrade. my main concern is dram config at this stage. your input will be much appreciated
DRAM configuration
Options
1-tCL auto 1-6 mine is set at 6
2-tRCD auto 1-7 mine is set at 7
3-tRP auto 1-7 mine is set at 7
4-tRAS auto 1-31 mine is set at 20
5-tRRD auto 1-15 mine is set at auto
6-tRC auto 1-31 mine is set at auto
7-tWR auto 1-6 mine is set at auto
8-tWTR auto 1-15 mine is set at auto
9-tREF auto 7.6us 3.9us mine is set at auto
10-command per clock (CMD) auto 1T 2T mine is set at 2T
cpu volt 3 tick above default
memory volt 1.9
north bridge 1.5 i think not sure
south bridge default
MSI P6N SLI Platinum
Q6600 Go revision
MSI 256 graphic card ATI HD 2400
2 X 1GB crucial pc6400 CL6
mastercoll 500Watts
window xpsp2

Have you tried decreasing RAM speed?
Read the Posting Guide.

P6N SLI PLATINUM CMOS BAD CHECKSUM ERROR TIME DATE

I have the same problem. It’s driving me crazy. Here is my specs:
MSI P6N SLI Platinum LGA 775
Intel Core 2 Duo E6420 2.13GHz 4M shared L2 Cache
Foxconn GeForce 7900GS 256MB 256-bit GDDR3 PCI Express x16
Western Digital Caviar SE16 WD7500AAKS 750GB 7200 RPM
Kingston KHX6400D2LLK2/2G 2GB kit PC2-6400 800MHZ
LG DVD GSA-H50N DVD-R 18X
Matsu"I'm a potty mouth"a Floppy drive
Windows XP 32-Bit
CoolerMaster RP-500-PCAR – 500W
+3.3V +5V +12V1 +12V2 -5V -12V +5VSB
20A 20A 16A 16A 0.8A 0.8A 2.0A
Sometimes the computer boots ok, and everything works great.
Sometimes it just doesn’t boot, it just gives a blank screen. So, I press reset and the post gives the CMOS CHECKSUM BAD. F1 to setup F2 to default.
If I go to the setup everything is just like I left, including the time. Even if I setup the bios with default configuration, the problem continues.
Here is a list of everything I have tried
1) Replaced the battery 2 times. I checked with a multimeter. It’s 3V allright
2) Disconnected everything leaving only 1GB memory and the graphics card
3) Updated the bios version several times, to make sure I did it ok. I cleared the CMOS after allright
4) I read every post in this forum about bios and P6N SLI Platinum
5) Already checked the D-BRACKET. It shows 4 green leds when the screen is blank
6) Already checked fans: CPU and graphics fans works ok
7) Already tested with memtest86+ V2.01
8) Already upped the northbridge to 1.325V, CPU 3 notches and the memory another 3 notches.
So anyone has any ideas, or I’ll just have to go to a computer store and swap the graphics or the PSU and try to see if the problem vanishes??? It’s gonna be tough… they don’t like to let you test the merchandise….
PS: Thanks for all the help so far that you have been giving to TheGimp, after all, we have the same problem…

I had the same problem after ~8months of trouble free service; it was intermittent too. sometimes it would boot fine, others times i'd get the error message. I removed the battery to test it. it was fine. i cleared the cmos with the button while the battery was removed. i noticed that the battery holder seems not to be anchored to the board at all. I haven't confirmed this but it looks like the protruding metal clip holds it all together. i had contacted MSI support about the problem earlier. they told me to clear the cmos. i asked about the battery holder not being secure on the board, and, as in the typical support response to an unusual question, they gave me some vague, undecipherable response. So, anyway when i put the battery back in, i felt the holder kind of click into place. I haven't had any problems since.

P6n sli platinum cannot boot up

Hello
Everytime I boot up the D bracket suggests the computer is failing on initializing the floppy drive controller. i have changed the cable, and changed the floppy drive but same effect.
In the BIOS, if I go through and F10 for no save and exit, it then exits to bank screen as it fails at the point above. If i make any changes in the BIOS, and then try to accept those changes it freezes on pressing either Y or enter. At that point all I can do is turn off and start again. Naturally it doen't retain those changes. I have done this several times to disable the floppy.
I have removed the battery and put it back, (It's 16 months old). It then did allow me to disable floppy but still machine did not go beyond the above point. Whenever I have tried to go back into the Bios again, it will now freeze when I try and accept any change in settings.
As you will see I am unable to even boot from a floppy at this point so cannot een consider updating the BIOS. However before yesterday it has been working perfectly.
Any suggestions, or the loan of an axe to reprogramme the ****** thing would be much appriecated.
Thank you
Malcolm
Motherboard P6N SLI Platinum, G52-73501x1-Q05
2.20.0050.10 BIOS verison
Intel Core 2 Duo Processor
Sony MPF920 floppy
4 Harddrives. Boot is IDE, then 3 others, one of which is sata
2 memory sticks, 2 gb ram
Plexwriter CD
Pioneer DVDRW 105
Pioneer DVD
DMX-6fire soundcard
HD620W power supply
full details not known as mostly stored on the computer
No faults on system since it was built 16 months ago

Quote from: yokochanie on 03-October-08, 13:55:28
Motherboard P6N SLI Platinum, G52-73501x1-Q05
2.20.0050.10 BIOS verison
Intel Core 2 Duo Processor
Sony MPF920 floppy
4 Harddrives. Boot is IDE, then 3 others, one of which is sata
2 memory sticks, 2 gb ram
Plexwriter CD
Pioneer DVDRW 105
Pioneer DVD
DMX-6fire soundcard
HD620W power supply
full details not known as mostly stored on the computer
No faults on system since it was built 16 months ago
"2 memory sticks, 2 gb ram"
That doesn't talk much, we need full details about it.
"Intel Core 2 Duo Processor"
Which one?
"2.20.0050.10 BIOS verison"
That's not your BIOS version, look here how to check==> https://forum-en.msi.com/index.php?topic=113146.0
What VGA you use?
Remove power cord from the PSU and leave just one memory stick in 1st DIMM, once done proceed with >>Clear CMOS Guide<<
Then try to boot, if no change disconnect any storages{4 HDD's, 3 Optical drives, and any USB devices which you may have attached} and re-test.

P6n sli platinum + e4300 oc

I've read tons of posts on forums, but most just give FSB speeds, not actual numbers to use in setting the system clock, so how do we know what to use actually?
When do you use the 1:1 ratio? or any of the others if your motherboard BIOS doesn't let you manually set your memory multiplier?
I have the updated BIOS from MSI LiveUpdater and Web
I've Disabled the following in BIOS
Execute Bit Disable
Set Limit CPUID MaxVal to 3
HPET
CPU Smart FAN Target
D.O.T. Control
Intel EIST
All Spread Spectrum including:
CPU Spread Spectrum
PCIE Spread Spectrum
CPU/LDT Spread Spectrum
SATA Spread Spectrum
Questions
System Clock-Auto,Linked,Manual
Which is best and when to use for what?
I went to 1333 for a steady 3.0ghz overclock. Temps were below 40C
at idle and were 65C under full load.
Adjust CPU Ratio-To what?
Stock shows 9, but can go from 6-9 as well.
Last night I got to FSB1600
Mem 800
with 8x multiplier
very fast, but lost settings on re-boot. So basically unstable.
CPU Voltage-Try to not increase this by first overclocking as much as I
can on stock voltage, but if it becomes unstable or won't boot, I just increase it how I see fit based on stability right? I just want a good bootable computer to use daily for about 3 hours and 48hrs on weekends.
Not too much into games yet, but will once I get speakers and a better monitor. Mostly business/student needs.
Memory Voltage-Stock is: Timing 5-5-5-15
Voltage 1.8 - 2.0
I got this to 2.2 and everything was fine.
I can manually set it to 4-4-4-12 1T as well.
NB Voltage-I got this as high as I could and it worked great, I think it was 1.7.I heard on forums that the higher you go the better for overclocking. Plus it's got a fan on it stock and I don't care about noise fan at all.
SB Voltage-I got this to 1.6 and it was fine too. But it's not cooled so how much is too much?
FSB VTT Voltage-I read that if you go to 20% it stabilizes your rig when
you overclock, so I set it and it worked great.
My Setup
Intel Core 2 Duo E4300 Allendale 1.8GHz
ZALMAN CNPS9500 LED 92mm 2 Ball Cooling Fan with Heatsink
Arctic Silver 5 Thermal Compound
MSI P6N SLI Platinum 650i
G.SKILL 2GB (2 x 1GB) DDR2 800 (PC2 6400) Dual Channel
COOLER MASTER Centurion 5 CAC-T05 Case
Thermaltake TR2 ATX 430W
EVGA GeForce 8600GT 256MB GDDR3 PCI Express x16 Video Card
Western Digital Caviar SE 160GB 7200 RPM SATA 3.0Gb
$700 exactly with shipping from NEWEGG
PURE BUDGET BUILD

Hello welcome to the forum,
Quote
System Clock-Auto,Linked,Manual
Which is best and when to use for what?
I went to 1333 for a steady 3.0ghz overclock. Temps were below 40C
at idle and were 65C under full load.
System clock I believe is how the memory freq is generated. "Auto" would be automatic, "Linked" would be linked to FSB speed, "Manual" wold be manually setting the speed.
65c on the cores or the CPU? Because if it's the cores, drop down, anywhere over 60c and your CPU may start skipping cycles.
Quote
Adjust CPU Ratio-To what?
Stock shows 9, but can go from 6-9 as well.
Last night I got to FSB1600
Mem 800
with 8x multiplier
very fast, but lost settings on re-boot. So basically unstable.
CPU ratio is the multiplier in which you times the FSB speed to generate/set the CPU clock. E.g:
Code: [Select]
FSB of 100x10 (cpu ratio) = 1000MHz CPU core speed.
Quote
CPU Voltage-Try to not increase this by first overclocking as much as I
can on stock voltage, but if it becomes unstable or won't boot, I just increase it how I see fit based on stability right? I just want a good bootable computer to use daily for about 3 hours and 48hrs on weekends.
Not too much into games yet, but will once I get speakers and a better monitor. Mostly business/student needs.
yes only increase for stability, never increase because you think you may need too.
Quote
Memory Voltage-Stock is: Timing 5-5-5-15
Voltage 1.8 - 2.0
I got this to 2.2 and everything was fine.
I can manually set it to 4-4-4-12 1T as well.
They are fine, just don't go over 2.3v, your RAM chips will start to fry otherwise.
Quote
NB Voltage-I got this as high as I could and it worked great, I think it was 1.7.I heard on forums that the higher you go the better for overclocking. Plus it's got a fan on it stock and I don't care about noise fan at all.
No, wrong way to do it. Do it like CPU VCore, only increase when stability is needed. Also monitor temperatures of NB as much as your CPU. Fan speeds don't bother me either, but temps do! Watch them at all times when overclocking.
Quote
SB Voltage-I got this to 1.6 and it was fine too. But it's not cooled so how much is too much?
Only increase if you need to, the SB core is usually the last voltage that needs increasing.
Quote
FSB VTT Voltage-I read that if you go to 20% it stabilizes your rig when
you overclock, so I set it and it worked great.
It's the voltage you supply to the FSB bus, too much and you will kill the FSB and your mainboard will be a fancy paper weight. Only increase when stability is needed, just like every other voltage.

P6N SLI Platinum

I recently built a new computer with the P6N SLI Platinum mobo. The cpu (Intel Duo 2 Core E4300), vid card (evga 8800 GTS), memory (mushkin 2gbddr2 800), hd (Maxtor 320 gig SATA), and psu (apevia atx 500 watt) are all new. When the computer boots, all the fans and leds come on, but the monitor doesn't get a signal and the screen is black. I reseated the vid card and tried dvi/vga adaptor and a different monitor. The orange light and green light on the mobo are on. I used the pcie power 6 pin plug for the vid card. The 24 pin and 4 pin power connections to the mobo are ok. I haven't seen the bios because of the black screen. I also cleared the cmos and still no signal. I also tried an old Voodoo 2 pci vid card without the 2d pass through option and still no signal (don't know if that would work any way, but worth a try). The optical drives and the hd spin so they seem ok. I installed the D bracket with the lights to the usb header and jdb header. Should I see lights on this D bracket when the computer is booting? I don't see any and I don't get any beeps.

I now have no lights on the D bracket after clearing cmos again. I tried booting with one stick of ram and no change, then I tried booting with no ram and no change (no D bracket lights and no beeps). At this point, I have very little plugged into mobo - 1 hd, two optical drives, cpu, 2 fans and that's it.
Here are the ps specs:
Model
Brand APEVIA
Model ATX-CW500WP4
SPEC
Type ATX
Maximum Power 500W
Fans 2
PFC No
Main Connector 20 + 4Pin
Dual +12V Yes
PCI-E Connectors 1 x 6Pin
Power Good Signal 100-500ms
Hold-up Time >10ms at full load
Efficiency > 70% under max range load
Over Voltage Protection Yes
Overload Protection Yes
Input Voltage 115/230 V
Input Frequency Range 50/60 Hz
Input Current 12A @ 115AC, 6A @ 230AC
Output +3.3V@17A, +5V@25A, +12V1@16A, +12V2@18A, [email protected], [email protected], [email protected]
MTBF 100,000 Hours
Approvals UL, CSA, TUV, CE
Features
Connectors 1 x Main connector (20+4 pin)
1 x 12V (P4)
6 x peripheral
2 x SATA
1 x PCI-E
2 x Floppy

P6N SLI Platinum mobo with hard drive/sata crashes

i've experienced a (now recurring) problem with my hardware over the past several months. i've come home from work twice now, once about 2 months ago, the other just today to find my computer stuck at the windows xp loading screen. if i tried to reboot the system, it would hang at that point, until i disconnected the offending drive/sata channel (i had 3 hard drives in my system, 1 150gb drive with operating system, ect, and 2 500gb drives for storage (mp3s, video, ect). i've narrowed the problem down to either the motherboard or the sata cables (i don't have spare cables to test with), as the hard drives work perfectly in an external usb enclosure. any ideas of what could be wrong?
basic system stats:
msi P6N SLI platinum motherboard
intel core 2 duo E6600 2.4ghz processor
crucial ballistix DDR2 800 (PC2 6400) 2 gb SDRAM
EVGA GeForce 8800 GTS video card
western digital raptor 150gb 10k rpm SATA hard drive
western digital caviar 500gb 7200 rpm SATA hard drive
PC Power and Cooling Silencer 750w power supply

in brief,
1- if you have one memory it should be in slot 1, closest to cpu, if two X 1Gb then they should be in one and three.
2- do you know what is virtual memory if so have you made adjustment or not.
3- you have freeze due to wrong bios setting till we get a good picture of your bios difficult to pin point the mistake, so use either a digi cam or web cam and take shoots of your bios then we can pin point the mistakes

P6n SLI PLATINUM bios v1.2

So I upgraded to 4gb ram finally, and have got it to work without errors in dimm slots 2 and 4, and have been having performance issues such as slow loading, stuttering in games, and just in general slowdown with loading up applications, but absolutely no crashes or freezes of any kind, no BSODs or anything else that would be hardware related I assume.
Defragged, fresh install of windows 7, video card drivers updated and everything else checks out fine. The only thing I can think of is that over in HardForum doing a google search brought me to this post:http://www.hardforum.com/showthread.php?t=1164174 with issues related to 4gb on the mainboard having slowdowns with older bios versions.
Seeing as how this is relevant to me getting new memory, my patriot memory gave out with BSODs so I was forced to upgrade but had way better performance with just 2gb stick of ram (even in win7).
Should I do a bios update?
Specs:
EVGA 8800gts 540mb 195.62 driver
4gb A-Data ram 5-5-5-12 2t clock, 1.9v
Windows 7 64-bit
Bios v1.2 A7350NMS P6N SLI Platinum Socket LGA-775
Core2duo E6600 @2.4ghz
I haven't really done much upgrading since I purchased this a few years back, and quite surprised to see the hit and stuttering in performance in games all of a sudden after upgrading to new ram, and the ram tested out fine for 3 days straight doing multiple passes with memtest 4.0. I tried doing it in DIMM slots 1 and 3 but have been getting errors, maybe I've got a bad board?
Quite confused as to what step I need to take next, thanks for any help!

Quote
Should I do a bios update?
Yes. >>Use the MSI HQ Forum USB flasher<<

MSI P6N SLI Platinum + E8400 OC Help!, Overclocking Is Limited

Hey guys im new to the site and I need your help! :(
I am trying to get passed 3262.5 Mhz (just got it up to 3.32ghz) preferably 3.6Ghz but every time I try to raise the FSB from 1500Mhz and up it halts and I have to reset the bios. Any help is greatly appreciated. Specs Below.
MSI P6N Sli Platinum Bios v1.7 + E8400 (067A/DA07)
2 X 1GB Crucial Ballistix Tracer pc2 8500
BIOS Temps/Volts
CPU Vcore - 1.168V
3.3V - 3.344V
5V - 4.961V
12V - 12.05V
5V - 5.016V
Bios Settings
Execute Bit Support - Disabled
Set Limit CPUID - Disabled
C1E - Disabled
Spread Spectrum - Disabled (ALL)
DOT Control - Disabled
EIST - Disabled
System Clock Mode - Manual
FSB Clock - 1600Mhz
Memory clock 1066
Ratio - 9
PCI-E Frequency - 100
CPU Voltage - 0.1000V
Memory Voltage - 2.0V
NB Voltage - 1.25
SB Voltage - 1.50
FSB VTT Voltage - 0%
Memory DRAM Timings
5-5-5-15
TRRD, TRC, TWR, TWTR, TREF - ALL Set to Auto.
CMD - 2T
Idle Temp - 34
Load Temp - 42
I think thats it if you need any more info let me know. Thanks!

Hello and welcome,
First of all, 1066MHz isnt garantueed to work on that board, I have the same and although is says so on the box, it isnt supported, look here:
http://eu.msi.com/index.php?func=prodmbspec&maincat_no=1&cat2_no=170&cat3_no=&prod_no=1140#menu
533/667/800Mhz only.
To reach 3.6 try following:
Raise NB step by step, until ~1.35V max, SB @stock, FSB VTT to 4 - 8%
Set FSB to 1600 and mem to 800 on auto timings, you can adjust those later.
And leave Vcore on 0.100V as said in your post.
See if you can get it to run then.

P6N SLI Platinum, no post (also!)

Hey guys.. I think I checked everything, but want to make sure.
Relatively new P6N (bought it, didn't have processor, stored it for the last 6 months) Platinum board. Finally got the CPU and Memory today (info below). Plugging it in, and I get.. nothing. No post, no beeps (with connected speaker), all lights on D-bracket *OFF*, all lights on keyboard *ON*. All fans come on as well. Both yellow/orange LED and the green LED between PCIs come on.
I slowly disconnected everything, and even ONLY with the board and CPU (no vid card and RAM, only front-panel and D-Bracket connected), still same result. Now, I'm thinking it MAY be the CPU, however, I would expect to still get ALL RED on the D-Bracket as per the manual. I don't have ready access to another 775 processor.
Items:
CPU - Intel E8400 (Wolfdale)
RAM - Corsair XMS2 (model "TWIN2X2048-6400C4") I've heard there was issues with this, is why I turned the board on without ANY RAM. Yes, it would not have posted, but I would/should have gotten a signal on the D-Bracket!
PSU - Antec NeoHE (430W, 3 12V rails, +3.3V 22A; +5V 14A; +12V 16A / rail; -12V 0.8A; +5Vsb 2.5A)
The only thing I have left to do is to try it outside the case. However, I'm posting here now in case anyone sees anything obvious I missed. I actually HOPE it's something I can do here - even if it NEEDS a bios update, I would still expect the D-Bracket to give me all reds ("The System will hang here if the CPU is damaged or not installed properly.") However, I'm afraid to turn the board on without a CPU. (Is that safe? Dangerous? I was iffy about not having the RAM in..)
Thanks all!
Mike.

Quote from: Jack the Newbie on 27-February-08, 04:18:29
The options usually change with the CPU that is installed.
Not sure, if the problem is only the current BIOS or if it is your CPU after all. It is hard to say at this point.
Eh, I'm hoping it's not the CPU. I can't verify if I get different options with the E8400 only because I get the same result (after updating to 1.5 and 1.6b3 BIOS revs as I had originally - everything powrs on, no D-LEDs (all off, NOT all red) and keyboard LEDs all on. So I don't even get the change to get into the BIOS to verify. :/ I'm sure that if I COULD, I could tweak the settings to at least get a stable system until I could use the processor at it's fullest, but.. as it is now, it's a nice lump of silicon.
Quote from: Jack the Newbie on 27-February-08, 04:18:29
This guy....
https://forum-en.msi.com/index.php?topic=114440.0
... was apparently able to get an E8400 working on a P6N SLI(-FI). It has the same model name & PCB Version as the P6N SLI Platinum.
I don't know, the best thing is probably to wait for a BIOS Update. Can you test you processor on another system that already supports Wolfdale CPUs?
I'm waiting. It's impressive - the P6N, even with the cheapest 1.6GHz Celeron processor is really nice. I won't have another LGA775 system to test with for another month. Hopefully, they'll have another beta or have released an update by then..
Thanks for your help, of course!
Mike.

4GB ram for P6N SLI Platinum

Can anyone recommend me good quality ram for my P6N SLI Plat. board ? I know some memory is incompatible with it so I need to know which one I can buy that will work and good memory.
I have Q6600 + 8800GTS 640 and P6N SLI Platinum bios v.1.1.

I've been extremely happy with running Corsair Dominator PC-8500C5D's (rated 1066 but 800 chipped), in both P7N & P6N. If your OS is XP, the 2X1G set in slots 1 & 3 works good. If you have Vista, 2X2G set in slots 1 & 3 would be a good combo as well.

Screen Freez (memory expert needed) P6N SLI platinum

Similar Messages

Maybe you are looking for