Screen is dim after software update

For the last day and a half, my MacBook screen won't go to full brightness. I have the power connected and I've rebooted and I'm using the screen, but it's still in "power save" or dim mode. It used to be that the screen would dim on battery power after a few minutes of not typing. Now it's just always dim.
The last thing I did before this happened was install some software updates that I was prompted to install. It says the System Version is Mac OS X 10.5.6 (9G66) but I'm not sure what all it upgraded Saturday night (there were like 12 downloads).
Maybe I can use Time Capsule to back out the upgrade and see if that helps, though the one time I tried to do that was a nightmare.....

You can't use the brightness key on the keyboard to increase brightness?
Also, try a SMC and PRAM reset. Shut down, unplug the magsafe, take out the battery, and hold down the power button for at least five seconds. Next, put everything back and start up holding command-option-p-r until it chimes twice. Then let it start up normally.

Similar Messages

Restart unsuccessful and screen gone back after software updated

I just got my iMac back from the store for hard drvie replacement programme. When I back home, I used the original OS install DVD to start up my computer, all went smoothly till the software update check, I tried to updated the software and restart the computer as per request, but the screen gone black and my computer never can start up again. What's going wrong? Can anyone help?

Hello,
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
If 10.7.0 or later...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.
If that doesn't help Reinstall the OS.

White screen - no startup after software updates 2007-007

I cannot start my mac g4 following a software upgrade I did last night. There were a series of upgrades. I just get a white screen and it will not boot. In the meantime, I cleared a partition on a second drive on the same machine and installed 10.4 on this and have used it to start up and look at the other drive. I have been backing up files onto one of my external drives but running out of disk space. I am really concerned since all my apps are on the original volume and I don't believe I can just transfer them. Problem is my partition on the drive I set up is also small (about 10gb) so thats not much room for anything more than the os plus a bit. Should I attempt to fix the original volume, should I try an archive and install, some advice really appreciated. Many thanks.

Hi there. Thanks for your advice. It is not practical to back up everything and I have backups of the files that are important but no one really wants to loose anything when you are confronted with making choices like this.
That said, I think some responsibility falls on Apple's shoulders to ensure that the older machines will update properly since it appears there are many g4's still in service. I have located another post similar to mine today that indicates this is not isolated to me - which leads me to believe it may just be a bad update.
Obviously there was some adverse effect from the new software since the system was good until the reboot with the updates. While I shouldn't expect this to occur, I get you're point about being prepared in the event it does. From my perspective, this experience is something that you'd expect from $MS. I have never had this type of experience after using a Mac now for almost 10 years. Worst case was a failing second drive (Maxtor) that I installed - but was able to recover the data using the Carbon Copy app.
In any case, I appreciate any replies and am hopeful I'll have recovered by the end of the day . Many thanks.

MBP Black Screen on restart after software update

Hello to all, Just after dowloading today's latest updates, iTunes, Safari, something about file exchanges and Apple remote I beleive, there needed to restart and once done, no chime and black screen...
All was perfectly fine just before, and I did backup beforehand.
Tried to reset PRAM, restart in Single user, Safe mode, Installation Disk, all with no success.
I will let it powered off and let it cool down for a while if it can help, but it was not particularly hot when restarted.
Any other suggestions ??
Many thanks !!

I'm having basically the same problem with my PowerBook 1Ghz Aluminum 17". After running the latest security update and latest iLife patches using SU, my system boots to the local Darwin consol login. I can see my HD and all it's files, but I can't get the machine to boot back into GUI mode. Safe mode doesn't work.
This was a newly refreshed system running 10.4.6 and ONLY iLife installed - nothing funky and no 3rd-party apps other than those pre-installed in 10.4.x.
I've booted with the 10.4 DVD, repaired permissions (again) and repaired the drive (reported not needed). Zapping the PRAM doesn't help.
Perhaps I have a lemon because I have had problems with this machine in the past, but only when installing major system updates between 10.3-10.4 with non-apple RAM. I don't think this is the culprit this time as the machine has been functioning fine since the last fresh 10.4 install (with some OWC RAM).
Any ideas? Anyone have tips for what can be done in the console to repair the system?
ARGH
PM G5-Quad 2.5GHz | eMac G4 1.25GHz | PM G4 800MHz | PB G4 1GHz 17 | PM G4 400MH Mac OS X (10.4.5)

Thin white line acroos the top of my screen after software update. Can NPRAM reset help to solve this or is it a permanent pixel problem?

Sudden thin white line acroos the top of my screen after software update. Can NPRAM reset help to solve or is it permanent pixel problem?

Try PRAM reset.
Reset PRAM: http://support.apple.com/kb/PH14222
Best.

Unable to log into administrator account after software update

I've done a clean installation of server 10.5 on a G5 Xserve using the simplified "workgroup" setting. Created a named administrator account as part of the setup. Once passed the initial setup screens I did a software update to 10.5.8. After reboot I'm locked out of the named administrator account. I can still log in as root and localadmin using the same password. However, I don't see any accounts listed under the Users tab in Server Preferences. I've done nothing to this system other than answer a few standard questions during install and then update software.
This result is repeatable as I tried simply reinstalling the server OS figuring I must have done something wrong the first time. In fact the reason I'm reinstalling in the first place is related to this problem. Something caused all my admin and user accounts to go away on the original server setup. Couldn't figure it out so I decided to do a fresh install. I realize now it was likely related to a software update.
When logged in as root and using Console I see errors like "'No LDAP Master' while processing a command of type: 'readSettings' in plug-in: 'servermgr_accounts'". I'm a newbie to the server world and I'm not sure what that means.
There should be nothing remotely fancy going on here. Simply a stand alone server getting a fixed IP from a router. A single admin account, no directory services. Before the software update everything seemed fine.
Any help would be appreciated.

Hi,
I have same issue and i have resolve so.
login as root and password
Verify if you have in /Users/xyz : your admin home folder
if yes, create a new user with : Preference System, Account, create new user
set as Administrator, give same name as your /Users/xyz home folder
then click OK, a message will appeart that the folder exist, click YES.
that's resolve my issue

IPhone went bad after software update - iPhone 5 is now stuck on Itunes connect and has vertical lines

iPhone went bad after software update - iPhone 5 is now stuck on Itunes connect and has vertical lines.
I found a video on youtube with similar issues - http://youtu.be/Xuuqxx18-bA
EVERYTHING HAS BEEN TRIED: Restore, Reboot, Recycle, Replacing Cables, etc....
I don't have Apple Care, what to do? Spend more money and buy a new phone?

Here is another person who has a problem with the iPhone 5 screen https://www.youtube.com/watch?v=sc1ZPWSA8dc and they have just received them NEW!!!!!
I myself, two days ago purchased a 2nd hand iPhone 5 that was advertised as having a line of squares at the bottom of the screen. I Googled it and found people saying it was a screen issue and to replace the screen, so I did this and it is still happening with a new screen.
I am starting to dislike Apple intensely after reading forum posts and watching videos where people are asking for help and telling us about issues that they are having with their phones.
Why is Apple getting it so wrong with their updates and manufacturing that they are completely destroying iPhones that cost a lot of money and then expecting the owner to purchase another phone unless they are still in warranty.
Apple you should be going out of your way to put things right for people but instead there is a wall of silence over so many of the issues destroying peoples phones.
SHAME ON YOU!

Macbook wont turn on After software update

PPlease help!
my macbook air 11 wont turn on After software update. The screen completely black . Power button is not responding éven if it is fully charged.
THank you
NOra

Have t you tried a SMC reset?
http://support.apple.com/kb/HT3964
It may be helpful if you indicated the EXACT MBA model you have and the OSX.
Ciao.

Problem restarting after software update

Computer is fine, drive 40% full, no speed problems...
But it just won't restart after software update runs, nor will it restart or shut down from finder.
Problem solving so far: Safe boot, reset pram, ran disk utility, ran disk repair using install disk, ran fsck -y, ran disk warrior.
Is annoying. ANy ideas anyone? If not, what is the procedure for updating using sudate and terminal, as when I use software update, a force shut down will not install.
ANy ideas folks?

Some general advice on updating:
It is worth noting that it is an extreme rarity for updates to cause upsets to your system, as they have all been extensively beta-tested, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first to an external hard disk. Ideally you should always have a bootable clone of your system that enables you to revert to the previous pre-update state.
Turn off sleep mode for both screen and hard disk.
Disconnect all peripherals except your keyboard and mouse.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site.
The Combo updater of Leopard 10.5.8 can be found here:
http://support.apple.com/downloads/MacOS_X_10_5_8_ComboUpdate
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
Full details about the 10.5.8 update here: http://support.apple.com/kb/HT3606
More information on using Software Updater here:
http://support.apple.com/kb/TA24901?viewlocale=en_US
Using the Combo updater ensures that all system files changed since the original 10.5.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.5.7 to 10.5.8. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications and turn off energy saving and screensaver.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious!
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them compliant with the latest version of your operating system. Give them a weeks or two while you regularly check their websites for updates. This applies particularly to plug-ins for Safari 4.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
Lastly, Apple's own article on the subject of Software Update may also be useful reading:
http://docs.info.apple.com/article.html?artnum=106695
If you are updating Safari (or just have):
Input Managers from third parties can do as much harm as good. They use a security loophole to reach right into your applications' code and change that code as the application starts up. If you have installed an OS update and Safari is crashing, the very first thing to do is clear out your InputManagers folders (both in your own Library and in the top-level /Library), log out and log back in, and try again.
So, disable all third party add-ons before updating Safari, as they may not have been updated yet for the new version. Add them back one by one. If something goes awry, remove it again and check on the software manufacturer's website for news of an update to match your version of Safari.
Most errors reported here after an update are due to an unrepaired or undetected inherent fault in the system, and/or a third party add-on.
Additional tips on software installation here:
http://docs.info.apple.com/article.html?artnum=106692
To reiterate, Input Managers reach right into an application and alter its code. This puts the behavior of the affected application outside the control and responsibility of its developers: a recipe for problems. That's not to say that issues absolutely will ensue as a result of Input Managers, but you, as a user, must decide. If the functionality of a specific Input Manager or set thereof is really important to you, you may well choose to assume the associated risk.
Again, the advice is to remove all Input Managers from the following directories:
• /Library/InputManagers
• ~/Library/InputManagers
especially prior to system updates (they can always be added back one-by-one later).

Iphone 5 stuck in portrait after software update

iphone 5 stuck in portrait after software update wont unlock i can see the lock symbol but cant find it in menu

Try swiping up from the bottom very bottom edge of the screen to reveal the Control Center. You should be able to turn off the rotation lock there (Round arrow with a lock in the middle)

Ipod touch4g is not detected in pc and itunes after software update

after software update is done. when i connect my ipod touch it is not detected in pc (windows 7) and in itunes please help me anyone.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

New iPad with retina display with 30 pin connector mirroring to TV with dvi adapter problems after software update

Hi. Good day to everyone my New iPad with retina display 30 pin connector will not mirror to TV even with divi adapter after software update. Adapter works fine. Or is it a software glitch with IOS 7.04? I've tried resetting and reconnecting nothing seems to work.

That's one of the weird things.. it recognizes it maybe 10% of the time. And usually, only after I do the two-button reset. Problem is.. since it won't charge above 2%, anytime I try to do a restore or anything like that using iTunes, my device shuts off and I lose whatever progress I'd made.
So, an update... after reading through a bunch of similar complaints (there are literally 1000's of them so there's NO WAY this isn't somehow ios7 related, thanks a lot APPLE ) I decided to try a restore in recovery mode. After 3 hours and several disconnections... I ended up having to just set it up as a new iPad, as the restore did nothing. Weirdly though... as I was doing the restore in recovery mode.. I noticed I'd gotten up to a 10% charge.. higher than it's been since September, so after setting it up as a new device, I turned it off and plugged it in using the wall charger. 2 hours later and I was up to 38%. Still not great, as my iPad, before ios7 could've fully charged twice in the amount of time it took for me to now get 28% more of a charge. And that's with a fully cleaned out device.. so that really ***** and I'm now more confused than ever.
But I'm gonna leave it overnight charging and see what I come up with tomorrow. Sadly, when I paid $600 for it in February, I never expected to have to play "wait and see" with it...

HT1338 iphone 3gs cant be activated after software update to ios5

iphone 3gs cant be activated after software update to ios5

What does it say when you look at Settings=>General=>About=>Carrier?
Which version of Cydia is on your iPhone - the one with the black & white
icon or another one? What color is the Cydia icon?

Internal camera failure after software updates...first skype couldn't......

Hello!
I am having internal camera failure after software updates...first skype couldn't find the camera, and now photo booth also says camera is not connected. Its a brand new MacBook Pro which has been working fine for a month, but after a software update (the blinking message said i had 13 new things to update...you know what I'm talking about right?) all of a sudden Skype couldnt find a camera, so i went to the skype community and tried some things (like trashing skype) but now photo booth says no camera detected, which is weird cause the camera is built into the computer..
Please help!
Thanks
O

First, reset the SMC:
http://support.apple.com/kb/HT3964
If that doesn't help, then take it to an Apple Store for examination.

Problem in curve 9320 after software update

Hi, i had updated my curve 9320 with new software as recommended by blackberry desktop software. After the update i am facing many issues after software update:
1. whenever I am trying to make a call or opening any message my phone power suddenly goes OFF and not starting till I pullback the battery and re-inserted.
2. Some time automatically its battery got heated up and there is discharge of battery, but when i pull back and re-inserted battery it becomes normal.
3. Email setup is not working, I am not able to add any email account. whenever I am clicking on email setup there is no reaction.
please suggest what to do. I tried to go back to download old software but I am not able to get it anywhere online.
regards
iftekhar

Hey iftekhar,
Welcome to the BlackBerry® Support Community Forums.
I would suggest backing up doing a clean reload of the BlackBerry® device software as shown here: http://btsc.webapps.blackberry.com/btsc/KB11320. Please test before restoring any data to the device.
If this resolves the issue do a selective restore of essential data (Address Book, Calendar, Task, Memos, BBM contacts etc.)
How to use BlackBerry® Desktop Software to restore data to a BlackBerry® smartphone from a backup file
http://btsc.webapps.blackberry.com/btsc/KB10339.
If the issue still persists after the reload, further investigation might be required. To help further diagnose the cause, contact your wireless service provider or BlackBerry® Technical Support Services for further review and support.
Thank you.
-HB
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Screen is dim after software update

Similar Messages

Maybe you are looking for