Screensaver does not end after specified time

i am running 10.6.4 on a 2008 Mac Pro. i have set the "flurry" screensaver to start after 5 minutes of inactivity, and set the display to go to sleep after 10 minutes. The screensaver starts after 5 minutes but does not turn off after 10 minutes, it stays on for an indefinite time.
Also the schedule i have created for my computer to shut down does not work either.
Since i have encountered this problem i have noticed that the status indicator light on the front of my 4TB WD MyBook Studio Edition II, connected via e-sata is not flashing but permanently on. This is happening even though i am not accessing the drive. Perhaps this could be the culprit.

Robs HD wrote:
i am running 10.6.4 on a 2008 Mac Pro. i have set the "flurry" screensaver to start after 5 minutes of inactivity, and set the display to go to sleep after 10 minutes. The screensaver starts after 5 minutes but does not turn off after 10 minutes, it stays on for an indefinite time.
Also the schedule i have created for my computer to shut down does not work either.
That sounds like the preferences file may be corrupted.
Quit System Preferences, then delete this file:
/Library/Preferences/SystemConfiguration/com.apple.PowerManagement.plist
Then re-enter your sleep/shutdown preferences.
Since i have encountered this problem i have noticed that the status indicator light on the front of my 4TB WD MyBook Studio Edition II, connected via e-sata is not flashing but permanently on. This is happening even though i am not accessing the drive. Perhaps this could be the culprit.
If a process is running and using that disk, it could prevent system shutdown, but not display sleep.
Is that new behavior for the WD? Is Spotlight continuously indexing that drive (a dot in the spotlight indicator at the right of your Menubar)?

Similar Messages

Screensaver does not start after upgrading to 10.7

Since upgrading to 10.7 my screensaver does not start either by hot corner or automatically. I can get it to test from the preference pane, any suggestions?

Okay.... Sorry for calling the technology airplay vice AirPrint. I have done all the standard power reset and wireless tips (i.e.delete the wireless network, re-add the wireless network, even monitored the RF frequency spectrum to make sure nobody is stomping on my wireless signal, solid 32Mbits over a Cisco 1811w). I have over 28 years in networking experience. So, I assume you all the basic stuff has been covered. Before our Apple devices got upgraded to IOS7 (2 IPads and 2 iPhones), we had no problems printing to our Brother HL-5450DN series printer (updated to the latest firmware). I strongly believe it has something to do with the AirPrint discovery process as shared in my last post. My next step is to enable port mirroring and monitor the packet exchange using wireshark or tcpdump. This will probably have to wait until the weekend.

Smart object does not appear at specified time in slide.

Here's my issue: When I insert a speech bubble into the slide, set it to appear after 5.0 seconds and the display for the rest of the slide, it does not appear at the specified time. HOWEVER, if I move the speech bubble to appear at the very START of the slide, then it appears. I thought perhaps I needed to add an effect to make it work, so I selected the thought bubble, then added a "fly in" effect and set the time. It still won't appear at a specified time--only if I put it at the start of the slide.
Here's my question: Why won't the smart object (speech bubble) appear at a specified time, but it WILL appear if I set the "appear after" time to 0 seconds? I also have tried moving this on the timeline, and it still only shows at the start of the slide.
Many thanks for any help.

Previewed in browser and in normal preview mode. (Just clicking "preview from this slide).
Normal project -- not responsive.
And..I'm not worried. No need for wine. (Although I've never been known to refuse one if someone offers. )
Screenshots below. As you can see, the image is not set sa a button.
And, yes: I know there is a spelling error in the thought bubble. Just trying to get it to work first.
I think there may be a bug in the system, as I have noticed other weird things. (EG: The time indicators under "timeline" often disappear for no reason. I have to close out and re-lauch Captivate to get it back. (Clicking on "timeline" in Windows dropdown does nothing to correct the issue. Other things I've noticed is that the navigation works fine when I play the whole project through ONCE, but upon a second preview, all settings -- such as "jump to slide __" -- do not stick. When I go back in and re-enter all of the navigation slide commands, the same thing happens when I replay it. My client notices the same thing. Bizarre.)

Wait activity does not expires after giving time frame

Hi all,
We are using SOA suite version 11.1.1.5. In our process, we use a wait activity so that the process will wait for a certain time frame (say 1 min) and again proceeds when the wait activity time expires.
The above process was running successfully for some months. But suddenly the instances are getting stopped in the wait activity and they are not proceeding after the given time.
The audit trail shows wait activity pending. And the wait activity does not expires even after the respected time.
Kindly suggest the possibilities of this scenario.
Regards,
Gopi

Hi Gopi,
You can look at the logs to see if there are for any errors/warnings during the wait activity execution.
A possible explanation can be due to an error in a later on activity (like invoke or assign). If you have an error that you didn't catch, the process will try to rollback to the last dehydrate point (in your case the wait activity) and stuck there.
Thanks
Arik

Album Art Screensaver does not work after iTunes 9 upgrade

After I upgraded to iTunes 9 my album art screensaver no longer works. I get the message saying "Your iTunes library does not contain any songs with artwork". I have tried deleting the plist files per another support topic, but this doesn't fix the problem. Ideas?

This is the Tiger forum - you are running Snow Leopard!
But I would suggest you post your question in the iTunes forum:
http://discussions.apple.com/forum.jspa?forumID=789

MBA 11 (2013) pinch zoom does not work after some time, how to fix it ?

Recently I purchased MBA 11 (2013) model ( 4GB ram & 1.3 Ghz dual core). Although I use iPhone 5 & iPad 4 but never used mac. So when I found the track pad is capable of pinch zoom(along with other gesture) I was excited. But later I found after opening few apps (like safari, chrome etc) pinch zoom stop working . I need to restart in order to make it work again. Other gestures works fine just issue with the pinch zoom. Along with this issue I have some other questions as well
1) How to fix this pinch zoom issue?
2) I use eclipse for android development, but when I connect android phone/tablet - os crashes, no idea why?
3) How to uninstall & update apps properly which was downloaded from web (like I installed x-code) ?
4) I want to use mouse (i am comfortable) - I need to know whether right click, wheel, ling click & drag works perfectly.
5) How to back up the os if something goes wrong I can retrieve from there ?

Error 2, 4 (or -4), 6, 40, 1000, 9006
Follow Troubleshooting security software. Often, uninstalling third-party security software will resolve these errors.
There may be third-party software that modifies your default packet size in Windows by inserting a TcpWindowSize entry into your registry. Your default packet size being set incorrectly can cause these errors. Contact the manufacturer of the software that installed the packet size modification for assistance or follow this article by Microsoft: How to reset Internet Protocol (TCP/IP).
Verify that access to ports 80 and 443 are allowed on your network.
Verify that communication to albert.apple.com or photos.apple.com is not blocked by a firewall, or other Internet security setting.
Discard the .ipsw file, open iTunes and attempt to download the update again. See the steps underAdvanced Steps > Rename, move, or delete the iOS software file (.ipsw) below for file locations.
Restore your device while connected to a different network.
Restore using a different computer.
http://support.apple.com/kb/TS3694#error6

Execution does not end even after all records updated..

Hi,
I have plsql code like :
declare
begin
for x in ( select .......) loop -- about 4000 times
for y in ( select ............) loop -- about 50 times
end loop;
-- some code goes here to manipulate clob data
-- like creating free temp clobs - use - then free them
-- Update statement that update some table using clob values.
insert into tablex values(sysdate);
commit;
end loop;
end;
Here I can monitor from other window howmany records are inserted into tablex and howmany updated in update statement by...
select count(1) from tablex;
After 50 mins i can see that all records are updated but...
plsql code does not end its execution it continues even after all records are updated..untill i have to kill the session or let be run for long time.. :(
I can not understand why this it is not ending execution..
What could be the problem ...

Hi,
Here it is.....
declare
v_text_data TableA.text_data%type;
v_clob clob;
type dummyclob_t is table of clob index by binary_integer;
dummyclob dummyclob_t;
v_str varchar2(255) := 'ddfsajfdkeiueimnrmrrttrtr;trtkltwjkltjiu4i5u43iou43i5u4io54urnmlqwmreqwnrewmnrewmreqwnm,rewqnrewqrewqljlkj';
begin
select data bulk collect into dummyclob from sfdl_clob; -- five rows containing clob data upto 1MB
for x in (select object_id
from TableA
where object_type = 'STDTEXT' ) loop
dbms_lob.createtemporary(v_text_data,TRUE);
for y in (select '<IMG "MFI_7579(@CONTROL=' || ref_id || ',REF_ID=' || ref_id || ').@UDV">' temp_data
from TableB
where object_id = x.object_id) loop
v_text_data := v_text_data ||
case
when trunc(dbms_random.value(0,7)) = 0
then chr(10)
else v_str
end ||
y.temp_data;
end loop;
select text_data into v_clob from TableA where object_id = x.object_id for update;
if v_text_data is not null then
dbms_lob.append(v_clob,v_text_data);
end if;
dbms_lob.append(v_clob,dummyclob(trunc(dbms_random.value(1, 6))));
dbms_lob.freetemporary(v_text_data);
insert into xyz values (sysdate);
commit;
end loop;
end;
Thanks for your time..:)
Rushang.

Time Machine does not start after external hard drive is connected

Time Machine does not start after external hard drive is connected

These are the iCloud storage options: http://www.apple.com/icloud/includes/lightbox-storage.html
Also bear in mind that:
1. restoring data over icloud takes time
2. iCloud is not designed as a replacement to Time Machine.

Installing patch 5217019 takes long time and does not end

Hi,
I try to install patch 5217109 to my TEST instance.While installing patch the 8 workers are selected default.7 of workers are in statu of completed but 1 worker is waiting for long times and does not end.
What can be my problem?

Start time for file is: Mon Aug 10 2009 11:45:01
sqlplus -s APPS/***** @/oracle/TEST/testappl/ad/11.5.0/admin/sql/adpcpcmp.pls APPLSYS &pw_fnd APPS &pw_apps &systempwd 8 1 NONE FALSE
Arguments are:
AOL_schema = APPLSYS, AOL_password = *****,
Schema_to_compile = APPS, Schema_to_compile_pw = *****,
SYSTEM_password = *****, Total_workers = 8, Logical_worker_num = 1
Object_type_to_not_compile = NONE
Use_stored_dependencies = FALSE
Connected.
Checking for previously-invalid objects which are now valid...
PL/SQL procedure successfully completed.
Elapsed: 00:00:00.03
Commit complete.
Elapsed: 00:00:00.00
Deleting any errors from previous run of this logical worker
0 rows deleted.
Elapsed: 00:00:00.00
Commit complete.
Elapsed: 00:00:00.00
Compiling invalid objects...

Access DB (& .ldb file) does not close after crystal reports

Post Author: mgold
CA Forum: Crystal Reports
Access DB (& .ldb file) does not close after crystal reports
Hi! We have a VB application using Crystal Reports 6 that has worked successfully on hundreds of systems for over 10 years. Now, on one network, the application and access database does not close. It seems to hang on the [.Close] command.
When we open the application an peruse the screens without opening up a report (using crystal reports), the application and access db closes fine. But as soon as we run a report and then close the report and try to close the application, the access db does not close. Many of the screens open the db and grab data from the access db, but it's only after running crystal reports that we have this problem. (Please see more information below.)
Setup: Application and data (access 97 db) reside on a server in the same folder, but application shortcut is kicked off on client PC. Kicking off the shortcut on the client PC means that the image/process runs on the client PC (not on the server). In this problem case, the application shortcut is on a Windows XP Pro Version 2002 SP2 PC with the app & data on a Windows 2003 server. Users are local Admins on their PCs with "Full Control"over the directory and files on the server where the data (access 97 db) resides. This type of setup is typical and has worked without any problems for clients.
The application is written in Visual Basic, using Crystal Reports 6 (using DAO). We close the recordset, set it to zero and then it hangs on closing the db (.Close command).
A few key pieces of information:
- The application closes fine if the app & data (access 97 db) are on a local PC. This includes closing fine if the application is run directly on the Windows 2003 server where the data is stored.
- It worked on this client's network until sometime in the last few weeks.
- One thing that changed is that the company is using VMWare on its servers. Not sure if they started using VMWare at the same time as it started failing. This may be unrelated. Possibly other things changed, but can't get any more information ... yet.
- It works fine running the application from a Windows Vista PC with a user who is a domain admin.
- The access db and application hang for about 10-20 minutes and then eventually closes. It appears that somehow
Crystal Reports is keeping the db open, but I'm not sure why.The application doesn't quit and the database doesn't close even if I try to end the task with the Task Manager.
- The Crystl32.ocx version being used is 8.0.0.4 (if that matters).
- I copied 6 month old program files and database files to a test folder on the Windows 2003 server. It fails using these files that worked fine 6 months ago.
Any ideas or help would be greatly appreciated! If you know of another good place to post this, please let me know.
Thanks!
- Mark

Crystal doesn't support tables in HTML interpretation.
You can probably work your way around this by doing Replace() calls on the relevant tags.
See:
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_erq/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/scn_bosap/notes%7B6163636573733d36393736354636443646363436353344333933393338323636393736354637333631373036453646373436353733354636453735364436323635373233443330333033303331333233313337333033383334%7D.do
The supported HTML tags are:
" html
" body
" div (causes a paragraph break)
" tr (causes only a paragraph break; does not
preserve column structure of a table)
" span
" font
" p (causes a paragraph break)
" br (causes a paragraph break)
" h1 (causes a paragraph break, makes the font bold
& twice default size)
" h2 (causes a paragraph break, makes the font bold
& 1.5 times default size)
" h3 (causes a paragraph break, makes the font bold
& 9/8 default size)
" h4 (causes a paragraph break, makes the font bold)
" h5 (causes a paragraph break, makes the font bold
& 5/6 default size)
" h6 (causes a paragraph break, makes the font bold
& 5/8 default size)
" center
" big (increases font size by 2 points)
" small (decreases font size by 2 points if it's 8
points or larger)
" b
" i
" s
" strike
" u
The supported HTML attributes are:
" align
" face
" size
" color
" style
" font-family
" font-size
" font-style
" font-weight

Site does not load after some minutes of creation or after restart the server

Hello,
I have been asked to create a test enviroment identical to the production enviroment. So, what I did was:
Backed up the production web application's content database: Prod_WSS_ContentDB
Created new test servers (domain controller, sql server and sharepoint 2013 server) in a new, completely isolated, network environment, without any connection with the production environment (specifically Azure)
Created a new web application in test environment with a new content database.
Dismounted the new content database with powershell: Dismount-spcontentdatabase Test_WSS_Content
Copy the Prod_WSS_ContentDB database to the test sql server and restored it with Management Studio.
Mount the Prod_WSS_ContentDB databe to the web application with powershell:
Mount-spcontentdatabse Prod_WSS_ContentDB -WebApplication http://testsp/
Then, when I type http://testsp in the browser it redirects me to http://testsp/SitePages/Home.aspx
and the site loads exactly as the production environment.
But, after some minutes, or if I restart the Sharepoint Server, when I navigate to
http://sitesp I am redirected to http://testsp/SitePages/Home.aspx
as expected, but the site does not load, the browser just show a complety blank page.
The Central Administration site loads normally.
Trying to fix it I found that if I dismount the content database Prod_WSS_ContentDB, then mount the test database Test_WSS_Content,
then navigate to the site, dismount Test_WSS_Content and finally mount again Prod_WSS_ContentDB, the site loads normally, no blank page, but after some minutes or if I restart the same happens again.
For the error event I receice in event viewer it seems that the problem is related to database. I have not found a solution for this error... How can I solve this?
The error is:
Log Name: Application
Source: Microsoft-SharePoint Products-SharePoint Foundation
Date: 6/27/2014 2:44:22 PM
Event ID: 5586
Task Category: Database
Level: Error
Keywords:
User: UCETEST\spaccount
Computer: TESTSP01.ucetest.edu.do
Description:
Unknown SQL Exception -2146893055 occurred. Additional error information from SQL Server is included below.
A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: SSL Provider, error: 0 - The handle specified is invalid)
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-SharePoint Products-SharePoint Foundation" Guid="{6FB7E0CD-52E7-47DD-997A-241563931FC2}" />
<EventID>5586</EventID>
<Version>15</Version>
<Level>2</Level>
<Task>3</Task>
<Opcode>0</Opcode>
<Keywords>0x4000000000000000</Keywords>
<TimeCreated SystemTime="2014-06-27T14:44:22.743159500Z" />
<EventRecordID>4742</EventRecordID>
<Correlation />
<Execution ProcessID="1688" ThreadID="1692" />
<Channel>Application</Channel>
<Computer>TESTSP01.ucetest.edu.do</Computer>
<Security UserID="S-1-5-21-2552298216-324766354-3392103171-1108" />
</System>
<EventData>
<Data Name="int0">-2146893055</Data>
<Data Name="string1">A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: SSL Provider, error: 0 - The handle specified is invalid)</Data>
</EventData>
</Event>
Melvintt
MCTS, Windows Server 2008 R2: Network Infrastructure
MCTS, Windows Server 2008 R2: Active Directory, Configuring

Hi,
According to your post, my understanding is that Site does not load after some minutes of creation or after restart the server.
Please make sure you create a test environment for existing production site correctly.
Here are some great articles for your reference:
Moving content between SharePoint environments
Copy SharePoint production data to a test environment
Build a SharePoint 2010 Test/Development Farm
Best Regards,
Linda Li
Linda Li
TechNet Community Support
Hello Linda Li,
I follwed that steps to create my test enviroment... and I have recreated it some times using that same steps, but the problem persits. After some minutes or after I restart the SharePoint server the site does not load.
Melvintt
MCTS, Windows Server 2008 R2: Network Infrastructure
MCTS, Windows Server 2008 R2: Active Directory, Configuring

TX2500Z touchscreen does not work after Windows7 upgrade from HP specific to S/N, etc on laptop.

My TX2500Z touchscreen does not work after I upgraded to Windows 7. I cannot find any support or drivers, etc. to fix. I bought Windows 7 directly from HP specific to my P/N and S/N on my TX2500Z. Any help? Thanks.

after 2,5 days (spending half a day within the apple shop as well with this problem) i have it all back on track.
i did a lot of different things: trying to remove and reinstall iPhoto; did a SL installation over the old SL I had on my HD; backing up all the data of course before and reformatting my HD and installing a new clean SL version on it + a new clean version of iLife9 with all the updates and than I migrate with migrate assistant all the data and setting with time machine back onto it, but all this didn't work, because it also migrated the error/bug through time machine with it.
so at the end i just installed a brand new, clean SL version on my hard drive, than I did the updates and put all my data, photos, docs, movies, mail, bookmarks, music, etc manual back into the system (drag and drop from my external HD, where i had an exact copy of my internal HD) and did all the settings again in all the different programs.
the only thing i used migrant assistant with time machine for was for the programs. it seems to work now all fine and i even got more free space on my HD, because some of the old stuff i always carried with me but i never used, i didn't take over.
basically everything is clean now. At least i hope and works fine. touch wood!

Process does not end when binding a object to registry

I am writing a Unit Test case in which i need to create a datasource and bind it to RMI registry so that the methods i need to test can get a database connection . The problem is that after the test cases have finished running the process does not end and i have to shut it down manually . When i do not bind the datasource , the process ends put with errors because the methods do not get a connection. Even unbinding it after running the test cases does not help.
Edited by: gurpreetbhalla on Jun 25, 2009 11:56 AM

public void testIntraDayForClient() throws Exception
          ConstantConfig.JNDI_FACTORY = "com.sun.jndi.rmi.registry.RegistryContextFactory";
          Hashtable env = new Hashtable();
          env.put(Context.INITIAL_CONTEXT_FACTORY,"com.sun.jndi.rmi.registry.RegistryContextFactory");
          env.put(Context.PROVIDER_URL, "rmi:");
InitialContext ic = new InitialContext(env);
// Construct DataSource
SQLServerConnectionPoolDataSource ds = new SQLServerConnectionPoolDataSource();
ds.setURL("jdbc:sqlserver://10.200.41.201:1433;databaseName=TradeportTC");
ds.setUser("sa");
ds.setPassword("superuser");
DataSource d = ds;
     ic.unbind("TCDB_JNDI");
ic.bind("TCDB_JNDI", ds);
          HttpServletRequest req = new MockHttpRequest();
          HttpServletResponse resp = EasyMock.createMock(HttpServletResponse.class);
          ActionContext context = EasyMock.createMock(ActionContext.class);
          HttpSession session = EasyMock.createMock(HttpSession.class);
          EasyMock.expect(session.getAttribute("ZephyrUserName")).andReturn("sclient90");
          EasyMock.expect(session.getAttribute("ZephyrDomainId")).andReturn("8a48a9cb1860e2a4011860e2c64d003a");
          EasyMock.expect(session.getAttribute("isTrader")).andReturn(false);
          EasyMock.expect(session.getAttribute("accountsDataDB")).andReturn(null);
          EasyMock.expect(context.getSession()).andReturn(session).times(12);
          session.setAttribute("vawTrades", null);
          session.setAttribute("noOfDays", null);
          session.setAttribute("accountNo", null);
          session.setAttribute("exchange", null);
          session.setAttribute("symbolName", null);
          session.setAttribute("trCode", null);
          session.setAttribute("status", null);
          session.setAttribute("accountsDataDB", null);
          EasyMock.replay(session);
          EasyMock.replay(context);
          MyOrdersAction action = new MyOrdersAction();
          action.execute(req, resp, context);
This is the unit test case which does not exit , if i skip this binding ic.bind("TCDB_JNDI", ds);
then it exits normally with a failure,

Getting Lync enable users who are modified after specified time

Getting Lync enable users who are modified after specified time
Hi,
I need to get all the Lync enabled users from Lync 2010 server who are modified after specified time.
I have written a client with this below code for my purpose
string
dateString = "11/4/2014 11:19:10 PM";
DateTime
lastModifiedTime = DateTime.Parse(dateString, System.Globalization.CultureInfo.InvariantCulture);
PSCommand command = new PSCommand();
command.AddCommand("Get-CsUser");
command.AddParameter("Filter",
"WhenChanged -gt " + lastModifiedTime.ToString());
powershell.Commands
= command;
Collection<PSObject> outPut = powershell.Invoke();
But on calling Invoke method I am getting the below exception,
Cannot bind parameter 'Filter' to the target. Exception setting "Filter": "Invalid cast problem for value: "11" type: "System.Nullable`1[System.DateTime]" query: "WhenChanged -gt 11/4/2014 11:19:10 PM" "17""
Can anyone please point me what am I doing wrong.
This command
Get-CsUser -filter {whenchanged -gt
"11/4/2014 11:19:10 PM"}
when run directly on Windows Powershell works fine.
Thanks in advance.
Sandeep

It appears you may be casting the date variable wrong.
If you have
command.AddParameter("Filter",
"WhenChanged -gt 11/4/2014 11:19:10 PM"
And avoid the lastModifiedTime.ToString() addition, does it work?
If so, it's just the way you're doing your date manipulation.
Also, why convert from a string to a datetype and back for the datestring? Are you trying to correct a timezone issue?
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
SWC Unified Communications
This forum post is based upon my personal experience and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

HT2693 My UPAD lite does not start after recent update. I have lots of info in it. Can anybody help me to get it back. Can I get the update out somehow? Thanks

My UPAD lite does not start after recent update. I have lots of info in it. Can anybody help me to get it back? Can I somehow undo the update? Thanks

"UPAD lite?"
I expect that you mean some version of iPad.
First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore, go into Recovery Mode per the instructions here.

Screensaver does not end after specified time

Similar Messages

Maybe you are looking for