Screenshot in window mode not working

I have the weird situation that the screenshot utility "grab.app" returns a blank image (of correct dimensions) when I select "capture window" and point to a window. All other modes work just fine. This is on all user accounts and with 10.6.3 (updated by the combo installer). Deleting preferences didn't help. A differently configured machine with same OS update history doesn't have the problem.
So, any clues what might be broken?
Thanks,
Jazz

Yes, it's not a permission issue. And it only happens on this one machine too. No error messages in any of the log files. This is a real tough one. I'm tempted to think that it might be a graphics driver issue. The machine with the problem is a 2008 Mac Pro with a GeForce 8800 GT. So if anyone with a similar configuration could test it I'd at least have another hint for what's going on.
As an interesting sidenote, other capture applications like Voila work fine, which makes the graphics driver theory unlikely, but well, I'm running out of possible causes.
Thanks,
Jazz

Similar Messages

Same issue Network Discovery not working and Windows Update not working

I've read the threads.
This is a Vista Ultimate upgrade. My OOOOH My I have clocked 8 hours
Everything was working before. I tried all of the recommended services turning on restarting.
Also, ran into the problem of my memory being eaten. Suspected cause hibernate mode, which I had to disable. Scott Hasselman blog recommended the fix which is a cheap work around that limits machines functionality!!
I'm and IT Engineer specializing in MS product lines since Windows 1.0. MFC foundation classes etc.. What is the real problem ?
I don't have the NetBIOS over tcp/ip in my services?
I figure that the cost of my time and other individuals pays for the OS four times over. Give me a Microsoft developer subscription or something to make me happy. This is my development machine and I'm loosing time and money.
FYI, Just upgraded my second machine to Windows 8.1 OMG !!2 Hours to upgrade after the download. I loose my configuration settings. I required to have a Windows Live whatever account!!! This is not the way to compete and keep customers.
Windows XP has been by far the best deployment experience. I need a Knowledge base that gives solutions , not a troubleshooting scenario that does or does not work!!
Please , don't tell me to go and by a OEM Surface I cannot recommend this to my clients.
Thank You

Hi,
If it worked previously, a quick solution is to run System Restore and get back to the previous status when the issue didn’t occur.
What is System Restore?
http://windows.microsoft.com/en-us/windows7/What-is-System-Restore
When you turn on network discovery, do you get any error prompt?
Please check if you have any error message about network discovery in event viewer.
Open Event Viewer
http://windows.microsoft.com/en-US/windows7/Open-Event-Viewer
What information appears in event logs (Event Viewer)?
http://windows.microsoft.com/en-US/windows7/What-information-appears-in-event-logs-Event-Viewer
Please use Windows Live SkyDrive (http://www.skydrive.live.com/) to upload the Error logs to a public folder and share the URLs with us.
Also, please temporarily turn off your firewall and all the security programs for a test.
As far as I know, Network discovery requires that the DNS Client, DNS Client, Network Connections, Network Location Awareness, Remote Procedure Call (RPC), Function Discovery
Resource Publication, TCP/IP Netbios helper, SSDP Discovery, and UPnP Device Host services are started and set to automatic.
You should check again if you have started all these services.
Regarding the update issue, I suggest you try the following suggestions.
1. Temporarily disable firewall and antivirus program to test the issue.
2. Open the Windows Update troubleshooter
http://windows.microsoft.com/en-US/windows7/Open-the-Windows-Update-troubleshooter
3. Reset Windows Update components
http://support.microsoft.com/kb/971058
You may follow the steps from the link below to fix the issue.
Windows Update Not Working.
http://support.microsoft.com/kb/555989
You may also see the common Windows Updates troubleshooting guide.
Fix Microsoft Windows Update Issues
http://support.microsoft.com/kb/906602
Hope it helps.
Regards,
Blair Deng
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Adobe Bridge CS5 in windows 7 not working?

Adobe Bridge CS5 in windows 7 not working. I was using bridge perfectly for last 2 years. It stops working since 3 days. I tried to install updates. Showing some error to install.
Tried to install creative cloud..again some error. Error code : 82
Could you please advice how I can fix my adobe bridge.

https://www.youtube.com/watch?v=xDYpTOoV81Q&feature=youtu.be
please check this video I uploaded..this is what happens when I click adobe bridge.. just blinks and go off. bridge not working on task manager

Why the buttons created by Acrobat XI in window do not work in android mobile or ipod touch?

Why the buttons created by Acrobat XI in window do not work in android mobile or ipod touch?

Hi,
Could you please send us a test file which has those form buttons? Please email that file to us at DL-adobereader-android <[email protected]>
Thanks,
- Reader Mobile team

Popups: Navigation from view to window does not work

Hi,
I open a second window as popup. This window has 2 views embedded, displaying view1 first. On some actions I would like to navigate to view2.
Defining an outbound plug on view1 and an inbound plug on view2, connecting them and firing the outbound withith the onaction works absolutely fine.
However, for some reasons I would like to avoid a direct navigation, but would like to navigate from view1 to the popupo window and from there to view2 (or maybe another view, ofcourse also embedded in the same popup window). Unfortunately I fail on this scenario - I can fire the view-to-window plug, but the destination on the window side (handle in method) is never reached.
Since the same concept works fine on non-popup windows I wonder whether a navigation from view to embedded window does not work for popups?
Any idea?

Hi Yashpal,
no, just one window.
The first link is view1 -> window, the second window -> view2.
I.e., I fire in the view the outbound plug, which is connected with its window.
In the window I fire an outbound plug, which is connected to view2.
In theory this should work - for non-popup windows I do not have any problem at all, however, for popup windows the navigation from view1 to the window is not processed.
In the meantime I played a little bit further: Instead of firing a navigation from view1, I now fire an event defined in the component contoller, on which an event method is registered within the window. Doing so, I reach the window, which I didn't reach via the navigation link. Once in the window, firing to view2 works just fine ...
Hope the issue is a bit clearer now. Also I found a solution, I am surprised that the simpler way via navigation does not work.

ITunes drag to import new songs in library or to create playlists from folders on windows does not work!

iTunes drag to import new songs in library or to create playlists from folders on windows does not work!
WHY? I have to solve, how can I do? Thank you

up

Windows updates not working because it extract patches on Mac partition first., Windows updates not working because it extract patches on Mac partition first.

I have installed BootCamp 5.1 and Windows updates not working because it extract files on Mac partition before installation. Is there any workaround for same ?

To replicate this issue - Try to download .net framework 4.5 from microsoft website and than run that setup on windows partition.
Before installation. it will first extract all the binaries to a other drivers, since in my case other primary drive is E which is a Mac partition so it always give me an error while extractiing and therefore setup is not able to execute propely.
Let me try to get the screen shot of error and send it here.

Widgets on my desktop using dev-mode not working in Lion

I'm trying to get iStat back ontop of my desktop like I had in Snow Leopard. Dev-mode not working to bring widgets forward anymore. Any Ideas how to do this in lion? In Snow Leopard it was defaults write com.apple.sashboard devmode YES now that isn't working.

When I connect my MBP (mid 2010) to iMac 27" (mid 2010), via Mini DisplayPorts, after pressing Command+F2, iMac screen went "blank" while MBP screen stays "blue" for few seconds and went back to normal. How to solve this problem?

Blue screen on start up. Safe mode not working?

Blue screen on start up. Safe mode not working, any suggestions?

Thank you, I had forgotten about target mode. I was able to back up all of my files. I also copied some additional 50 GB of files of the disk as a stress test and the hard drive worked fine and quick (and because it was quicker than retrieving the same files from a network drive to my desktop).
I was hoping to also unpack the Applejack files on my desktop and put them back so I could run them in single user mode without running /etc/rc. However I haven't been able to get my Linux desktop to mount the iBook in Read-Write instead of Read-Only yet (I don't have access to another Mac at the moment).

Windows 10 sleep mode not working

windows 10 sleep mode not working

I hope this helps. But... I had the same problem last week. Now I don't as of 8/17/15. I am not sure if a windows 10 update fixed this. I do not like problems that without any assistance fix themselves. However, try sleep mode again. This problem may have been fixed.

Target Display Mode not working iMac 27(2012) Bootcamp to iMac 27(2013)

Hi All,
I recently purchased an iMac 27" 2013 which replaced my iMac 27" 2010.
===============
PREVIOUS SETUP
===============
(1) iMac 27" 2012 - Running Windows 8.1
(2) iMac 27" 2010 - Running OS X Mavericks
(1)+(2) were connected with a Mini-Display-Port cable.
(1) was using (2) as external display while (2) was set to Target Display Mode using CMD+F2
==============
CURRENT SETUP
==============
(1) iMac 27" 2013 - Running Windows 8.1
(2) iMac 27" 2012 - Running OS X Mavericks
(1)+(2) are connected with Thunderbolt cable.
(1) can't use (2) as external display anymore becuase CMD+F2 has no effect anymore on (2) in this scenario.
If (1) and (2) are both running OS X all works as expected.
I am aware about the support hint from Apple where they state TDM is not working under Bootcamp.
And I agree, while booted into Windows Bootcamp this machine can't serve as external display. Makes sense because TDM is baked into OS X display drivers.
Anyone had the same experience and came to a soltuion?
Thanks,
Martin

"Apple has no plans to implement a client driver for Windows since there is no Thunderbolt SW stack available for Windows like there is for Display Port."
That is a little bit funny since Gigabyte and other big companies have said that 2014 is the year that they are going to implement Thunderbolt in many motherboards.
"GIGABYTE 7 series motherboards are the very first to offer fully certified dual onboard Thunderbolt™ ports. Capable of connecting up to 12 devices plus 3 digital displays simultaneously with breathtaking data transfer speeds that can transfer 1TB of data in only five minutes, GIGABYTE Thunderbolt™ motherboards offer the fastest connection interface on the desktop PC."
Have you asked Apple about that? I dont understand why Apple is crippling Thunderbolt on their devices...

N95 8Gb USB Data Transfer Mode not working

I have a bizarre problem with USB Data transfer.
a) I upgraded to the new 15.x firmware with the correct HKCSL package - 0557980
b) I connected PC #1 in data transfer mode with no issue and copied a bunch of installers onto the mass memory and went on to install them - to the PHONE memory.
c) Later in the day, connected PC #2 and did the same with the last few applications.
d) Next day tried to connect PC #1 and it didn't work
e) Thought I must have an application using the MASS storage but checked and not so - all apps on Phone memory.
f) Went to PC #2 and tried - Data transfer mode works - no problem.
g) Tried PC #1 again, and still not working. I get all the right messages (Mass storage cannot be used at this time etc) on the handset, and I get the "safely remove hardware" option appearing on the PC - but I don't get a drive letter assigned in the Windows Explorer.
h) I have tried it on PC #3 and this works as well - no problem.
1. The working PC's both have PC Suite 2-Beta installed, while the problem PC has no PC suite at all.
2. I have downloaded the Nokia-connectivity_cable_driver_rel_6_85_10_0 and it installs properly - giving all the expected wireless... options in Device Manager, but I still don't get a drive letter assigned with the basic data transfer mode on this problem PC #1
So the issue seems to be with a PC that has never seen any version of PC suite, but it worked straight after the firmware upgrade.
All PC's are XP SP2.
Any suggestions on anything else to try ?
Regards

SOLVED by:
- attaching N95, selecting USB Data Transfer Mode
- Going to Device Manager
- Selecting the USB Mass Storage Device for N95
- "Uninstall"
- Remove cable when N95 says its safe to
- Re-attach cable
The PC then re-discovered and reloaded the drivers including the mass storage which then worked normally.
No idea what messed it up in the first place though.

Airport in bridge mode not working in Windows7

Hi everyone,
Last night as I was browsing the web on my iPad the internet stopped working...I am using an Airport Express router plugged directly into the wall socket of my apartment which was configured by the ISP.
I have been using this config for the past 7 months with no issues but last night it just stopped working and the yellow indicator started flashing.
I went into Airport utility and it tells me the Double NAT problem has been found (maybe the ISP changed something?)...and they suggest to change the Airport configuration to Bridge Mode ... said and done...now the Internet works fine under OSX and on my iPad but it does not work anymore in Windows 7.
Some of my family uses Windows 7 for some very specific apps and now it's just dead, internet does not work anymore.
Also, in OSX / iOS I didn't make any changes, I just changed the Airport configuration to Bridge mode and it worked right off the bat.
Has anybody else confronted such problems before ? If so, what would be the best way to fix this ?
Thanks!

" I tried trunk port also but it got disabled" <----- if your L2 config is not correct, nothing will work.
What is the setup on the switch ? Trunk or access vlan ?
What is the status of the interface ? up ? down ?
Do you see something in your arp table ?
Gilles.

Right click on a link and selecting "open in new window" does not work. How do I gewt this feature to work? PS Right click on a link and selecting open in new tab does.

No matter where the link is - in an e-mail or on a web page - the "Open in new window" feature does not work. Very annoying. Also I close Firefox in a session, but then cannot re-open it. When I shut my PC down I get a prompt to End Task -[ Firefox ] and a window opens asking if I want to save tabs and quit; quit; or cancel. After closing Firefox it does not show as an application running in Task Manager
== This happened ==
Every time Firefox opened
== I recently re-installed Firefox.

Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]
If it does work in Safe-mode then disable all your extensions and then try to find which is causing it by enabling one at a time until the problem reappears.
You can use "Disable all add-ons" on the ''Safe mode'' start window.
You have to close and restart Firefox after each change via "File > Exit" (on Mac: "Firefox > Quit")

MAXIMIZE WINDOW DOES NOT WORK IN FORMS 9i

Hi,
I am performing forms conversion and developing new forms in Forms 9i. The problem I am running into is that :
the SET_WINDOW_PROPERTY(FORMS_MDI_WINDOW, WINDOW_STATE, MAXIMIZE)
and SET_WINDOW_PROPERTY(ROOT_WINDOW, WINDOW_STATE, MAXIMIZE)
in the When_new_form_instance trigger don't work.
I've also tried adding a parameter to initiate the running mode as WEB as suggested in a response that I saw on this
forum, with that parameter I would set the ROOT_WINDOW State to NORMAL
then set WIDHT=800, HEIGHT=600, POSITION=0, 24.........
but it still does not work. When I run the form, the browser opens up as a full screen, but the form only fills up the gray rectangular
area when the Jiniator is running and loading the applet.
If I don't set the Maximize property of the main window to Yes then the vertical and horizontal scroll bars are automatically added,
if I do set so then no scroll bar is added and the form is cut off.
Is it a known problem ? and is there a solution to it?
Any response is greatly appreciated.
Thanks.
TLe

Thanks, it worked, and I've been playing with other parameters, such as replacing the lookandfeel (this works), but splashscreen and background don't when I specified the .GIF file name, it did not display the GIF image.
Thanks again.

Screenshot in window mode not working

Similar Messages

Maybe you are looking for