SCSI Disc Read-Only

hi
i have Arch linux installed on my SCSI disc (Seagate Cheetah 18GB)
my controler is
Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 (rev 04)
working on kernel 2.6.15-ARCH (from 0.7.1 installation CD)
with default initrd ....
sometimes i get error like
(scsi0:A:0:0): Unexpected busfree in Data-out phase
SEQADDR == 0x7d
sd 0:0:0:0: SCSI error: return code = 0x10000
end_request: I/O error, dev sda, sector 664214
Buffer I/O error on device sda3, logical block 6718
lost page write due to I/O error on sda3
and my filesystem goes read-only ... after reset everything goes back to normal ... how i can prevent going read-only on "/" and restarting my linux ?

well disabling one of modules doesn't help
i created my own initrd with
HOSTCONTROLLER_SCSI: aic7xxx sd_mod
and only this module is loadedfor my scsi controller
but i still get error
after error i restarted my computer and runned
Drive Verify
in SCSI Controller Setup (Ctrl-A at start up) and and drive was veryfied without  any error so i guess that isn't my drive problem
maybe will help that after this error my linux doesn't hang-up .. just FS goes readonly .. i still can read every file on disc .. just cannot write to them
... after restart everything is ok for about 2-3 days ....
please help ..

Similar Messages

  • I have downloaded Mountain Lion and Time Machine says that my Free Agent Goflex (Seagate) external 2gb drive cannot be used as it is read only. I tried disc utility to repair permissions but that block is greyed out. The disc verifies as being OKI

    Since installing Mountain Lion, Time Machine says says that my Free Agent Goflex (Seagate) external 2gb drive cannot be used as it is read only. I tried disc utility to repair permissions but that block is greyed out. The disc verifies as being OKI What next?

    Ok, I solved this problem! I ejected the drive and then disconnected it both from the power supply and the USB connector. I then reconnected everything and powered it up again and Then went into TM preferences and chose the drive as the backup. TM did a new backup (well over an hour) and now works as advertised.

  • Installing Yosemite failed, and it turned my disc into "read only"

    Tried to upgrade my MacBook Pro (Early 2011) to 10.10 from 10.9.5 AppStore. It failed after reboot. Then the disaster began...
    (Yes, unfortunately I didn't backup...)
    My disc became "Read only":
    I couldn't install 10.10, neither reinstall 10.9.5.
    Tried to repair the disc and permissions with 10.10 Disk Utility, both failed.
    Tried Disk Utility in 10.9.5 recovery, it says "unable to mount the disc".
    Tried to use Disk Utility "Restore", to copy the entire volume to another disc, it gave me "Could not restore - Input/output error",
    Tried to create a new image from that disc, still Input/output error.
    Then I used a new disc, clean installed Yosemite on it. However, I couldn't migrate my data from the old disc. In Migration Assistant, it couldn't find any source. (Tried to connect to another disc with clean installed Yosemite, Migration Assistant could find it)
    When I tried to simply copy "all files" (including all hidden files) to another empty disc, I always ended up with "The operation can’t be completed because you don’t have permission to access “some file”." ("some file" changes every time).
    Thai disc had been working for over one year without any problem, until I hit "Upgrade to Yosemite"...
    It's been a week now, and I have no idea what else I can try to repair my disc / make it writable again / migrate system information from that disc... Please help!

    First, look at this article and see if your model can do an Internet Recovery: Computers that can be upgraded to use OS X Internet Recovery. If yours needs the firmware update, then do that  before moving on.
    Install Mavericks, Lion/Mountain Lion Using Internet Recovery
    Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
    Boot to the Internet Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
    Partition and Format the hard drive:
    Select Disk Utility from the main menu and click on the Continue button.
    After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
    Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
    This should restore the version of OS X originally pre-installed on the computer.
    If for some reason your hard drive cannot be repartitioned or is not even visible in Disk Utility, then the drive has failed and needs to be replaced.

  • Can You Burn an Disc with JPEGs That is Read Only

    Is it possible to burn a disc through the finder that will have only JPEGs and have it be read only so no one can copy the images to another computer? Just see them, not copy.

    No.
    Screen capture utilities exist that circumvent that protection. Better to embed a watermark if you are worried about copying.

  • 'CD-RW' discs being read as 'READ ONLY'

    meaning I can't burn anything...
    I've tried a few different discs and each time I'm opening Disk Utility and their 'write ability' is 'read only'.
    This is the second time I've had a problem with my Superdrive.
    Could anyone suggest anything? Before i have to go to the Apple store?
    Thanks

    Hi greggle,
    don't worry, it just the way disk utility read the info.
    you can try to insert the blank cd and as soon as it shows up at desktop, drag files you want to burn and eject, it will burn the files instead of eject it.
    system preference > cd & DVD > when you insert blank cd > open finder (to show the cd at your desktop)
    Good luck.

  • Help.  After updating my software my external disc is "read" only.  How do I change this back to read and write?, help.  After updating my software my external disc is "read" only.  How do I change this back to read and write?

    Help.  After updating my software my external disc is "read" only.  How do I change it back to Read and Write?
    Thanks

    Have you formatted it for Mac using Disk Utility?
    If not, open Disk Utility (Applications>Utilities folder) and select the drive to the left. Make sure that you select "Mac OS Extended (Journaled)" and then the erase button.
    If you have already formatted the drive, call back...
    Clinton

  • External hard disc is read only on my MacBook air and I can't safe and export files on it, how can I change that

    My external hard drive is read only on my MacBook air and I cand safe  or export files to it. How can I change this so I can use the external hard drive to export my files and work on an other pc.

    Eject and disconnect the drive (and its power supply, if it has a separate one) for a few moments, then restart it.  Restart your Mac, then reconnect the drive.
    If that doesn't help, the directory structure may be damaged.  See if you can Repair it, per #6 in Using Disk Utility.

  • Read only filesystem problem

    Hi,
    I have a strange problem. After some time of running archlinux the root filesystem suddenly becomes read-only. It happened 3 times yet. I'm using LVM and the root volume is /dev/mapper/VG0-archlinux2 and filesystem type is reiserfs.
    If i tried to remount it read-write using command
    mount -o remount,rw /
    i got this:
    sudo: unable to open /var/db/sudo/uiii/3: Read-only file system
    mount: /dev/mapper/VG0-archlinux2: can't read superblock
    Only reboot helps.
    my machine is (uname -a):
    Linux uiii-arch 3.5.4-1-ARCH #1 SMP PREEMPT Sat Sep 15 08:12:04 CEST 2012 x86_64 GNU/Linux
    /etc/mtab (when problem occured):
    rootfs / rootfs rw 0 0
    proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0
    sys /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0
    dev /dev devtmpfs rw,nosuid,relatime,size=1990100k,nr_inodes=497525,mode=755 0 0
    run /run tmpfs rw,nosuid,nodev,relatime,mode=755 0 0
    /dev/mapper/VG0-archlinux2 / reiserfs ro,relatime 0 0
    devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000 0 0
    shm /dev/shm tmpfs rw,nosuid,nodev,relatime 0 0
    tmpfs /tmp tmpfs rw,nosuid,nodev,relatime 0 0
    /dev/sda1 /boot ext2 rw,relatime 0 0
    /dev/mapper/VG0-uloziste /mnt/uloziste ext4 rw,relatime,data=ordered 0 0
    binfmt /proc/sys/fs/binfmt_misc binfmt_misc rw,relatime 0 0
    gvfs-fuse-daemon /home/uiii/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,relatime,user_id=1000,group_id=100 0 0
    dmesg output is this:
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Linux version 3.5.4-1-ARCH (tobias@T-POWA-LX) (gcc version 4.7.1 20120721 (prerelease) (GCC) ) #1 SMP PREEMPT Sat Sep 15 08:12:04 CEST 2012
    [ 0.000000] Command line: root=/dev/mapper/VG0-archlinux2 ro initrd=../initramfs-linux.img BOOT_IMAGE=../vmlinuz-linux
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cfedffff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000cfee0000-0x00000000cfee2fff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000cfee3000-0x00000000cfeeffff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x00000000cfef0000-0x00000000cfefffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000012fffffff] usable
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] DMI 2.4 present.
    [ 0.000000] DMI: Gigabyte Technology Co., Ltd. GA-MA790X-UD4/GA-MA790X-UD4, BIOS F3 06/03/2009
    [ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x130000 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-C7FFF write-protect
    [ 0.000000] C8000-FFFFF uncachable
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
    [ 0.000000] 1 base 000080000000 mask FFFFC0000000 write-back
    [ 0.000000] 2 base 0000C0000000 mask FFFFF0000000 write-back
    [ 0.000000] 3 base 0000CFF00000 mask FFFFFFF00000 uncachable
    [ 0.000000] 4 base 000100000000 mask FFFFE0000000 write-back
    [ 0.000000] 5 base 000120000000 mask FFFFF0000000 write-back
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] TOM2: 0000000130000000 aka 4864M
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] e820: update [mem 0xcff00000-0xffffffff] usable ==> reserved
    [ 0.000000] e820: last_pfn = 0xcfee0 max_arch_pfn = 0x400000000
    [ 0.000000] found SMP MP-table at [mem 0x000f5600-0x000f560f] mapped at [ffff8800000f5600]
    [ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
    [ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
    [ 0.000000] Using GB pages for direct mapping
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0xcfedffff]
    [ 0.000000] [mem 0x00000000-0xbfffffff] page 1G
    [ 0.000000] [mem 0xc0000000-0xcfdfffff] page 2M
    [ 0.000000] [mem 0xcfe00000-0xcfedffff] page 4k
    [ 0.000000] kernel direct mapping tables up to 0xcfedffff @ [mem 0x1f9fd000-0x1fffffff]
    [ 0.000000] init_memory_mapping: [mem 0x100000000-0x12fffffff]
    [ 0.000000] [mem 0x100000000-0x12fffffff] page 2M
    [ 0.000000] kernel direct mapping tables up to 0x12fffffff @ [mem 0xcfede000-0xcfedffff]
    [ 0.000000] RAMDISK: [mem 0x7fc62000-0x7fffefff]
    [ 0.000000] ACPI: RSDP 00000000000f7010 00014 (v00 GBT )
    [ 0.000000] ACPI: RSDT 00000000cfee3000 0003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
    [ 0.000000] ACPI: FACP 00000000cfee3040 00074 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
    [ 0.000000] ACPI: DSDT 00000000cfee30c0 05980 (v01 GBT GBTUACPI 00001000 MSFT 03000000)
    [ 0.000000] ACPI: FACS 00000000cfee0000 00040
    [ 0.000000] ACPI: SSDT 00000000cfee8b00 008F5 (v01 PTLTD POWERNOW 00000001 LTP 00000001)
    [ 0.000000] ACPI: HPET 00000000cfee9400 00038 (v01 GBT GBTUACPI 42302E31 GBTU 00000098)
    [ 0.000000] ACPI: MCFG 00000000cfee9440 0003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
    [ 0.000000] ACPI: TAMG 00000000cfee9480 0030A (v01 GBT GBT B0 5455312E BG?? 53450101)
    [ 0.000000] ACPI: APIC 00000000cfee8a40 00084 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] Scanning NUMA topology in Northbridge 24
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000012fffffff]
    [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x12fffffff]
    [ 0.000000] NODE_DATA [mem 0x12fffc000-0x12fffffff]
    [ 0.000000] [ffffea0000000000-ffffea0004bfffff] PMD -> [ffff88012b600000-ffff88012f5fffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00010000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal [mem 0x100000000-0x12fffffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00010000-0x0009efff]
    [ 0.000000] node 0: [mem 0x00100000-0xcfedffff]
    [ 0.000000] node 0: [mem 0x100000000-0x12fffffff]
    [ 0.000000] On node 0 totalpages: 1048175
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 6 pages reserved
    [ 0.000000] DMA zone: 3913 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 16320 pages used for memmap
    [ 0.000000] DMA32 zone: 831264 pages, LIFO batch:31
    [ 0.000000] Normal zone: 3072 pages used for memmap
    [ 0.000000] Normal zone: 193536 pages, LIFO batch:31
    [ 0.000000] ACPI: PM-Timer IO Port: 0x4008
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x10b9a201 base: 0xfed00000
    [ 0.000000] SMP: Allowing 4 CPUs, 1 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
    [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
    [ 0.000000] PM: Registered nosave memory: 00000000cfee0000 - 00000000cfee3000
    [ 0.000000] PM: Registered nosave memory: 00000000cfee3000 - 00000000cfef0000
    [ 0.000000] PM: Registered nosave memory: 00000000cfef0000 - 00000000cff00000
    [ 0.000000] PM: Registered nosave memory: 00000000cff00000 - 00000000e0000000
    [ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
    [ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
    [ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 0000000100000000
    [ 0.000000] e820: [mem 0xcff00000-0xdfffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88012fc00000 s83392 r8192 d23104 u524288
    [ 0.000000] pcpu-alloc: s83392 r8192 d23104 u524288 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1028713
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: root=/dev/mapper/VG0-archlinux2 ro initrd=../initramfs-linux.img BOOT_IMAGE=../vmlinuz-linux
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] __ex_table already sorted, skipping sort
    [ 0.000000] Checking aperture...
    [ 0.000000] No AGP bridge found
    [ 0.000000] Node 0: aperture @ c4000000 size 32 MB
    [ 0.000000] Aperture pointing to e820 RAM. Ignoring.
    [ 0.000000] Your BIOS doesn't leave a aperture memory hole
    [ 0.000000] Please enable the IOMMU option in the BIOS setup
    [ 0.000000] This costs you 64 MB of RAM
    [ 0.000000] Mapping aperture over 65536 KB of RAM @ c4000000
    [ 0.000000] PM: Registered nosave memory: 00000000c4000000 - 00000000c8000000
    [ 0.000000] Memory: 3980204k/4980736k available (4645k kernel code, 788036k absent, 212496k reserved, 4207k data, 760k init)
    [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] NR_IRQS:4352 nr_irqs:712 16
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 16777216 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.003333] Fast TSC calibration using PIT
    [ 0.006666] Detected 2813.035 MHz processor.
    [ 0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 5628.48 BogoMIPS (lpj=9376783)
    [ 0.000005] pid_max: default: 32768 minimum: 301
    [ 0.000027] Security Framework initialized
    [ 0.000031] AppArmor: AppArmor disabled by boot time parameter
    [ 0.000260] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.001554] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.002140] Mount-cache hash table entries: 256
    [ 0.002315] Initializing cgroup subsys cpuacct
    [ 0.002317] Initializing cgroup subsys memory
    [ 0.002326] Initializing cgroup subsys devices
    [ 0.002327] Initializing cgroup subsys freezer
    [ 0.002328] Initializing cgroup subsys net_cls
    [ 0.002330] Initializing cgroup subsys blkio
    [ 0.002349] tseg: 00cff00000
    [ 0.002351] CPU: Physical Processor ID: 0
    [ 0.002352] CPU: Processor Core ID: 0
    [ 0.002353] mce: CPU supports 6 MCE banks
    [ 0.002358] LVT offset 0 assigned for vector 0xf9
    [ 0.002362] using AMD E400 aware idle routine
    [ 0.002998] ACPI: Core revision 20120320
    [ 0.019730] ftrace: allocating 17970 entries in 71 pages
    [ 0.027072] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.060076] CPU0: AMD Phenom(tm) II X3 720 Processor stepping 02
    [ 0.165799] Performance Events: AMD PMU driver.
    [ 0.165802] ... version: 0
    [ 0.165803] ... bit width: 48
    [ 0.165803] ... generic registers: 4
    [ 0.165804] ... value mask: 0000ffffffffffff
    [ 0.165805] ... max period: 00007fffffffffff
    [ 0.165806] ... fixed-purpose events: 0
    [ 0.165807] ... event mask: 000000000000000f
    [ 0.185858] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.199154] Booting Node 0, Processors #1 #2
    [ 0.235675] Brought up 3 CPUs
    [ 0.235679] Total of 3 processors activated (16884.46 BogoMIPS).
    [ 0.239344] devtmpfs: initialized
    [ 0.240745] PM: Registering ACPI NVS region [mem 0xcfee0000-0xcfee2fff] (12288 bytes)
    [ 0.241490] NET: Registered protocol family 16
    [ 0.241574] node 0 link 0: io port [c000, ffff]
    [ 0.241576] TOM: 00000000d0000000 aka 3328M
    [ 0.241578] Fam 10h mmconf [mem 0xe0000000-0xe00fffff]
    [ 0.241580] node 0 link 0: mmio [a0000, bffff]
    [ 0.241582] node 0 link 0: mmio [d0000000, dfffffff]
    [ 0.241584] node 0 link 0: mmio [f0000000, fe02ffff]
    [ 0.241586] node 0 link 0: mmio [e0000000, e03fffff] ==> [e0100000, e03fffff]
    [ 0.241588] TOM2: 0000000130000000 aka 4864M
    [ 0.241589] bus: [00, 03] on node 0 link 0
    [ 0.241590] bus: 00 [io 0x0000-0xffff]
    [ 0.241591] bus: 00 [mem 0x000a0000-0x000bffff]
    [ 0.241592] bus: 00 [mem 0xd0000000-0xdfffffff]
    [ 0.241593] bus: 00 [mem 0xe0400000-0xffffffff]
    [ 0.241594] bus: 00 [mem 0xe0100000-0xe03fffff]
    [ 0.241595] bus: 00 [mem 0x130000000-0xfcffffffff]
    [ 0.241649] ACPI: bus type pci registered
    [ 0.241696] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.241698] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
    [ 0.252350] PCI: Using configuration type 1 for base access
    [ 0.252819] bio: create slab <bio-0> at 0
    [ 0.252870] ACPI: Added _OSI(Module Device)
    [ 0.252871] ACPI: Added _OSI(Processor Device)
    [ 0.252872] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.252873] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.253366] ACPI: EC: Look up EC in DSDT
    [ 0.258796] ACPI: Interpreter enabled
    [ 0.258802] ACPI: (supports S0 S3 S4 S5)
    [ 0.258819] ACPI: Using IOAPIC for interrupt routing
    [ 0.261632] ACPI: No dock devices found.
    [ 0.261636] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.261677] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.261731] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7]
    [ 0.261733] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff]
    [ 0.261735] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
    [ 0.261737] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff]
    [ 0.261738] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xfebfffff]
    [ 0.261768] PCI host bridge to bus 0000:00
    [ 0.261770] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.261772] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.261773] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.261775] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
    [ 0.261777] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xfebfffff]
    [ 0.261786] pci 0000:00:00.0: [1002:5958] type 00 class 0x060000
    [ 0.261797] pci 0000:00:00.0: reg 1c: [mem 0xe0000000-0xffffffff 64bit]
    [ 0.261830] pci 0000:00:02.0: [1002:5978] type 01 class 0x060400
    [ 0.261858] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
    [ 0.261878] pci 0000:00:0a.0: [1002:597f] type 01 class 0x060400
    [ 0.261906] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold
    [ 0.261931] pci 0000:00:11.0: [1002:4390] type 00 class 0x01018f
    [ 0.261949] pci 0000:00:11.0: reg 10: [io 0xff00-0xff07]
    [ 0.261958] pci 0000:00:11.0: reg 14: [io 0xfe00-0xfe03]
    [ 0.261967] pci 0000:00:11.0: reg 18: [io 0xfd00-0xfd07]
    [ 0.261976] pci 0000:00:11.0: reg 1c: [io 0xfc00-0xfc03]
    [ 0.261985] pci 0000:00:11.0: reg 20: [io 0xfb00-0xfb0f]
    [ 0.261994] pci 0000:00:11.0: reg 24: [mem 0xfe02f000-0xfe02f3ff]
    [ 0.262013] pci 0000:00:11.0: set SATA to AHCI mode
    [ 0.262058] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310
    [ 0.262070] pci 0000:00:12.0: reg 10: [mem 0xfe02e000-0xfe02efff]
    [ 0.262132] pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310
    [ 0.262145] pci 0000:00:12.1: reg 10: [mem 0xfe02d000-0xfe02dfff]
    [ 0.262212] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320
    [ 0.262230] pci 0000:00:12.2: reg 10: [mem 0xfe02c000-0xfe02c0ff]
    [ 0.262309] pci 0000:00:12.2: supports D1 D2
    [ 0.262311] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
    [ 0.262334] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310
    [ 0.262346] pci 0000:00:13.0: reg 10: [mem 0xfe02b000-0xfe02bfff]
    [ 0.262408] pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310
    [ 0.262421] pci 0000:00:13.1: reg 10: [mem 0xfe02a000-0xfe02afff]
    [ 0.262493] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320
    [ 0.262511] pci 0000:00:13.2: reg 10: [mem 0xfe029000-0xfe0290ff]
    [ 0.262590] pci 0000:00:13.2: supports D1 D2
    [ 0.262591] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
    [ 0.262616] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500
    [ 0.262711] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a
    [ 0.262726] pci 0000:00:14.1: reg 10: [io 0x0000-0x0007]
    [ 0.262735] pci 0000:00:14.1: reg 14: [io 0x0000-0x0003]
    [ 0.262744] pci 0000:00:14.1: reg 18: [io 0x0000-0x0007]
    [ 0.262753] pci 0000:00:14.1: reg 1c: [io 0x0000-0x0003]
    [ 0.262762] pci 0000:00:14.1: reg 20: [io 0xfa00-0xfa0f]
    [ 0.262817] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300
    [ 0.262837] pci 0000:00:14.2: reg 10: [mem 0xfe024000-0xfe027fff 64bit]
    [ 0.262901] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
    [ 0.262915] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100
    [ 0.262987] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401
    [ 0.263028] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310
    [ 0.263041] pci 0000:00:14.5: reg 10: [mem 0xfe028000-0xfe028fff]
    [ 0.263105] pci 0000:00:18.0: [1022:1200] type 00 class 0x060000
    [ 0.263119] pci 0000:00:18.1: [1022:1201] type 00 class 0x060000
    [ 0.263130] pci 0000:00:18.2: [1022:1202] type 00 class 0x060000
    [ 0.263141] pci 0000:00:18.3: [1022:1203] type 00 class 0x060000
    [ 0.263155] pci 0000:00:18.4: [1022:1204] type 00 class 0x060000
    [ 0.263201] pci 0000:01:00.0: [10de:05e2] type 00 class 0x030000
    [ 0.263210] pci 0000:01:00.0: reg 10: [mem 0xfa000000-0xfaffffff]
    [ 0.263219] pci 0000:01:00.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.263229] pci 0000:01:00.0: reg 1c: [mem 0xf8000000-0xf9ffffff 64bit]
    [ 0.263235] pci 0000:01:00.0: reg 24: [io 0xef00-0xef7f]
    [ 0.263242] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0007ffff pref]
    [ 0.269149] pci 0000:00:02.0: PCI bridge to [bus 01-01]
    [ 0.269155] pci 0000:00:02.0: bridge window [io 0xe000-0xefff]
    [ 0.269157] pci 0000:00:02.0: bridge window [mem 0xf8000000-0xfbffffff]
    [ 0.269161] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.269200] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000
    [ 0.269213] pci 0000:02:00.0: reg 10: [io 0xde00-0xdeff]
    [ 0.269232] pci 0000:02:00.0: reg 18: [mem 0xfdfff000-0xfdffffff 64bit pref]
    [ 0.269245] pci 0000:02:00.0: reg 20: [mem 0xfdfe0000-0xfdfeffff 64bit pref]
    [ 0.269253] pci 0000:02:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
    [ 0.269300] pci 0000:02:00.0: supports D1 D2
    [ 0.269301] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.275814] pci 0000:00:0a.0: PCI bridge to [bus 02-02]
    [ 0.275820] pci 0000:00:0a.0: bridge window [io 0xd000-0xdfff]
    [ 0.275822] pci 0000:00:0a.0: bridge window [mem 0xfdc00000-0xfdcfffff]
    [ 0.275825] pci 0000:00:0a.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
    [ 0.275865] pci 0000:03:07.0: [168c:001a] type 00 class 0x020000
    [ 0.275887] pci 0000:03:07.0: reg 10: [mem 0xfdee0000-0xfdeeffff]
    [ 0.276014] pci 0000:03:0e.0: [104c:8024] type 00 class 0x0c0010
    [ 0.276035] pci 0000:03:0e.0: reg 10: [mem 0xfdeff000-0xfdeff7ff]
    [ 0.276047] pci 0000:03:0e.0: reg 14: [mem 0xfdef8000-0xfdefbfff]
    [ 0.276136] pci 0000:03:0e.0: supports D1 D2
    [ 0.276138] pci 0000:03:0e.0: PME# supported from D0 D1 D2 D3hot
    [ 0.276174] pci 0000:00:14.4: PCI bridge to [bus 03-03] (subtractive decode)
    [ 0.276177] pci 0000:00:14.4: bridge window [io 0xc000-0xcfff]
    [ 0.276181] pci 0000:00:14.4: bridge window [mem 0xfde00000-0xfdefffff]
    [ 0.276185] pci 0000:00:14.4: bridge window [mem 0xfdd00000-0xfddfffff pref]
    [ 0.276186] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.276188] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.276190] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.276191] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
    [ 0.276193] pci 0000:00:14.4: bridge window [mem 0xd0000000-0xfebfffff] (subtractive decode)
    [ 0.276205] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [ 0.276360] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
    [ 0.276399] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
    [ 0.276426] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCEA._PRT]
    [ 0.276447] pci0000:00: Requesting ACPI _OSC control (0x1d)
    [ 0.276449] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
    [ 0.276450] ACPI _OSC control for PCIe not granted, disabling ASPM
    [ 0.282962] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.282993] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.283022] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.283049] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.283077] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.283104] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.283131] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.283158] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.283250] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.283252] vgaarb: loaded
    [ 0.283253] vgaarb: bridge control possible 0000:01:00.0
    [ 0.283281] PCI: Using ACPI for IRQ routing
    [ 0.291632] PCI: pci_cache_line_size set to 64 bytes
    [ 0.291638] pci 0000:00:00.0: no compatible bridge window for [mem 0xe0000000-0xffffffff 64bit]
    [ 0.291701] e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
    [ 0.291703] e820: reserve RAM buffer [mem 0xcfee0000-0xcfffffff]
    [ 0.291778] NetLabel: Initializing
    [ 0.291779] NetLabel: domain hash size = 128
    [ 0.291780] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.291789] NetLabel: unlabeled traffic allowed by default
    [ 0.291804] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
    [ 0.291807] hpet0: 4 comparators, 32-bit 14.318180 MHz counter
    [ 0.293841] Switching to clocksource hpet
    [ 0.298189] pnp: PnP ACPI init
    [ 0.298200] ACPI: bus type pnp registered
    [ 0.298257] pnp 00:00: [bus 00-ff]
    [ 0.298260] pnp 00:00: [io 0x0cf8-0x0cff]
    [ 0.298262] pnp 00:00: [io 0x0000-0x0cf7 window]
    [ 0.298264] pnp 00:00: [io 0x0d00-0xffff window]
    [ 0.298265] pnp 00:00: [mem 0x000a0000-0x000bffff window]
    [ 0.298267] pnp 00:00: [mem 0x000c0000-0x000dffff window]
    [ 0.298268] pnp 00:00: [mem 0xd0000000-0xfebfffff window]
    [ 0.298295] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
    [ 0.298303] pnp 00:01: [io 0x0010-0x001f]
    [ 0.298304] pnp 00:01: [io 0x0022-0x003f]
    [ 0.298306] pnp 00:01: [io 0x0044-0x005f]
    [ 0.298307] pnp 00:01: [io 0x0062-0x0063]
    [ 0.298308] pnp 00:01: [io 0x0065-0x006f]
    [ 0.298310] pnp 00:01: [io 0x0074-0x007f]
    [ 0.298311] pnp 00:01: [io 0x0091-0x0093]
    [ 0.298312] pnp 00:01: [io 0x00a2-0x00bf]
    [ 0.298313] pnp 00:01: [io 0x00e0-0x00ef]
    [ 0.298315] pnp 00:01: [io 0x04d0-0x04d1]
    [ 0.298316] pnp 00:01: [io 0x0220-0x0225]
    [ 0.298317] pnp 00:01: [io 0x0290-0x0294]
    [ 0.298353] system 00:01: [io 0x04d0-0x04d1] has been reserved
    [ 0.298355] system 00:01: [io 0x0220-0x0225] has been reserved
    [ 0.298356] system 00:01: [io 0x0290-0x0294] has been reserved
    [ 0.298359] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.298785] pnp 00:02: [io 0x4100-0x411f]
    [ 0.298789] pnp 00:02: [io 0x0228-0x022f]
    [ 0.298791] pnp 00:02: [io 0x040b]
    [ 0.298792] pnp 00:02: [io 0x04d6]
    [ 0.298793] pnp 00:02: [io 0x0c00-0x0c01]
    [ 0.298794] pnp 00:02: [io 0x0c14]
    [ 0.298796] pnp 00:02: [io 0x0c50-0x0c52]
    [ 0.298797] pnp 00:02: [io 0x0c6c-0x0c6d]
    [ 0.298798] pnp 00:02: [io 0x0c6f]
    [ 0.298799] pnp 00:02: [io 0x0cd0-0x0cd1]
    [ 0.298801] pnp 00:02: [io 0x0cd2-0x0cd3]
    [ 0.298802] pnp 00:02: [io 0x0cd4-0x0cdf]
    [ 0.298803] pnp 00:02: [io 0x4000-0x40fe]
    [ 0.298804] pnp 00:02: [io 0x4210-0x4217]
    [ 0.298806] pnp 00:02: [io 0x0b00-0x0b0f]
    [ 0.298807] pnp 00:02: [io 0x0b10-0x0b1f]
    [ 0.298808] pnp 00:02: [io 0x0b20-0x0b3f]
    [ 0.298810] pnp 00:02: [mem 0x00000000-0x00000fff window]
    [ 0.298812] pnp 00:02: [mem 0xfee00400-0xfee00fff window]
    [ 0.298818] pnp 00:02: disabling [mem 0x00000000-0x00000fff window] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.298844] pnp 00:02: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0007ffff pref]
    [ 0.298848] pnp 00:02: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:02:00.0 BAR 6 [mem 0x00000000-0x0000ffff pref]
    [ 0.298885] system 00:02: [io 0x4100-0x411f] has been reserved
    [ 0.298887] system 00:02: [io 0x0228-0x022f] has been reserved
    [ 0.298889] system 00:02: [io 0x040b] has been reserved
    [ 0.298891] system 00:02: [io 0x04d6] has been reserved
    [ 0.298892] system 00:02: [io 0x0c00-0x0c01] has been reserved
    [ 0.298894] system 00:02: [io 0x0c14] has been reserved
    [ 0.298896] system 00:02: [io 0x0c50-0x0c52] has been reserved
    [ 0.298897] system 00:02: [io 0x0c6c-0x0c6d] has been reserved
    [ 0.298899] system 00:02: [io 0x0c6f] has been reserved
    [ 0.298900] system 00:02: [io 0x0cd0-0x0cd1] has been reserved
    [ 0.298902] system 00:02: [io 0x0cd2-0x0cd3] has been reserved
    [ 0.298904] system 00:02: [io 0x0cd4-0x0cdf] has been reserved
    [ 0.298905] system 00:02: [io 0x4000-0x40fe] has been reserved
    [ 0.298907] system 00:02: [io 0x4210-0x4217] has been reserved
    [ 0.298908] system 00:02: [io 0x0b00-0x0b0f] has been reserved
    [ 0.298910] system 00:02: [io 0x0b10-0x0b1f] has been reserved
    [ 0.298912] system 00:02: [io 0x0b20-0x0b3f] has been reserved
    [ 0.298914] system 00:02: [mem 0xfee00400-0xfee00fff window] has been reserved
    [ 0.298917] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.298986] pnp 00:03: [dma 4]
    [ 0.298988] pnp 00:03: [io 0x0000-0x000f]
    [ 0.298989] pnp 00:03: [io 0x0080-0x0090]
    [ 0.298991] pnp 00:03: [io 0x0094-0x009f]
    [ 0.298992] pnp 00:03: [io 0x00c0-0x00df]
    [ 0.299014] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.299038] pnp 00:04: [irq 0 disabled]
    [ 0.299049] pnp 00:04: [irq 8]
    [ 0.299051] pnp 00:04: [mem 0xfed00000-0xfed003ff]
    [ 0.299070] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
    [ 0.299088] pnp 00:05: [io 0x0070-0x0073]
    [ 0.299108] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.299114] pnp 00:06: [io 0x0061]
    [ 0.299134] pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
    [ 0.299140] pnp 00:07: [io 0x00f0-0x00ff]
    [ 0.299147] pnp 00:07: [irq 13]
    [ 0.299167] pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.299271] pnp 00:08: [io 0x03f0-0x03f5]
    [ 0.299272] pnp 00:08: [io 0x03f7]
    [ 0.299279] pnp 00:08: [irq 6]
    [ 0.299281] pnp 00:08: [dma 2]
    [ 0.299312] pnp 00:08: Plug and Play ACPI device, IDs PNP0700 (active)
    [ 0.299438] pnp 00:09: [io 0x03f8-0x03ff]
    [ 0.299445] pnp 00:09: [irq 4]
    [ 0.299485] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
    [ 0.299507] pnp 00:0a: [io 0x0060]
    [ 0.299509] pnp 00:0a: [io 0x0064]
    [ 0.299516] pnp 00:0a: [irq 1]
    [ 0.299543] pnp 00:0a: Plug and Play ACPI device, IDs PNP0303 (active)
    [ 0.299562] pnp 00:0b: [mem 0xe0000000-0xefffffff]
    [ 0.299596] system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved
    [ 0.299598] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.299674] pnp 00:0c: [mem 0x000cda00-0x000cffff]
    [ 0.299675] pnp 00:0c: [mem 0x000f0000-0x000f7fff]
    [ 0.299677] pnp 00:0c: [mem 0x000f8000-0x000fbfff]
    [ 0.299678] pnp 00:0c: [mem 0x000fc000-0x000fffff]
    [ 0.299680] pnp 00:0c: [mem 0xcfee0000-0xcfefffff]
    [ 0.299681] pnp 00:0c: [mem 0xffff0000-0xffffffff]
    [ 0.299682] pnp 00:0c: [mem 0x00000000-0x0009ffff]
    [ 0.299684] pnp 00:0c: [mem 0x00100000-0xcfedffff]
    [ 0.299685] pnp 00:0c: [mem 0xfec00000-0xfec00fff]
    [ 0.299687] pnp 00:0c: [mem 0xfee00000-0xfee00fff]
    [ 0.299688] pnp 00:0c: [mem 0xfff80000-0xfffeffff]
    [ 0.299692] pnp 00:0c: disabling [mem 0x000cda00-0x000cffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.299694] pnp 00:0c: disabling [mem 0x000f0000-0x000f7fff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.299696] pnp 00:0c: disabling [mem 0x000f8000-0x000fbfff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.299698] pnp 00:0c: disabling [mem 0x000fc000-0x000fffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.299701] pnp 00:0c: disabling [mem 0x00000000-0x0009ffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.299703] pnp 00:0c: disabling [mem 0x00100000-0xcfedffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.299745] system 00:0c: [mem 0xcfee0000-0xcfefffff] could not be reserved
    [ 0.299747] system 00:0c: [mem 0xffff0000-0xffffffff] has been reserved
    [ 0.299749] system 00:0c: [mem 0xfec00000-0xfec00fff] could not be reserved
    [ 0.299750] system 00:0c: [mem 0xfee00000-0xfee00fff] could not be reserved
    [ 0.299752] system 00:0c: [mem 0xfff80000-0xfffeffff] has been reserved
    [ 0.299755] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.299768] pnp: PnP ACPI: found 13 devices
    [ 0.299769] ACPI: ACPI bus type pnp unregistered
    [ 0.306130] pci 0000:01:00.0: BAR 6: assigned [mem 0xfb000000-0xfb07ffff pref]
    [ 0.306133] pci 0000:00:02.0: PCI bridge to [bus 01-01]
    [ 0.306135] pci 0000:00:02.0: bridge window [io 0xe000-0xefff]
    [ 0.306138] pci 0000:00:02.0: bridge window [mem 0xf8000000-0xfbffffff]
    [ 0.306140] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.306144] pci 0000:02:00.0: BAR 6: assigned [mem 0xfdf00000-0xfdf0ffff pref]
    [ 0.306145] pci 0000:00:0a.0: PCI bridge to [bus 02-02]
    [ 0.306147] pci 0000:00:0a.0: bridge window [io 0xd000-0xdfff]
    [ 0.306149] pci 0000:00:0a.0: bridge window [mem 0xfdc00000-0xfdcfffff]
    [ 0.306152] pci 0000:00:0a.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
    [ 0.306155] pci 0000:00:14.4: PCI bridge to [bus 03-03]
    [ 0.306157] pci 0000:00:14.4: bridge window [io 0xc000-0xcfff]
    [ 0.306162] pci 0000:00:14.4: bridge window [mem 0xfde00000-0xfdefffff]
    [ 0.306165] pci 0000:00:14.4: bridge window [mem 0xfdd00000-0xfddfffff pref]
    [ 0.306191] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.306193] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.306195] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.306197] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
    [ 0.306198] pci_bus 0000:00: resource 8 [mem 0xd0000000-0xfebfffff]
    [ 0.306200] pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
    [ 0.306202] pci_bus 0000:01: resource 1 [mem 0xf8000000-0xfbffffff]
    [ 0.306203] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.306205] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
    [ 0.306207] pci_bus 0000:02: resource 1 [mem 0xfdc00000-0xfdcfffff]
    [ 0.306209] pci_bus 0000:02: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref]
    [ 0.306210] pci_bus 0000:03: resource 0 [io 0xc000-0xcfff]
    [ 0.306212] pci_bus 0000:03: resource 1 [mem 0xfde00000-0xfdefffff]
    [ 0.306214] pci_bus 0000:03: resource 2 [mem 0xfdd00000-0xfddfffff pref]
    [ 0.306215] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
    [ 0.306217] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
    [ 0.306219] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.306220] pci_bus 0000:03: resource 7 [mem 0x000c0000-0x000dffff]
    [ 0.306222] pci_bus 0000:03: resource 8 [mem 0xd0000000-0xfebfffff]
    [ 0.306249] NET: Registered protocol family 2
    [ 0.306336] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.307016] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
    [ 0.309549] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    [ 0.309858] TCP: Hash tables configured (established 524288 bind 65536)
    [ 0.309859] TCP: reno registered
    [ 0.309868] UDP hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.309895] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.309974] NET: Registered protocol family 1
    [ 0.710572] pci 0000:01:00.0: Boot video device
    [ 0.710585] PCI: CLS 4 bytes, default 64
    [ 0.710637] Unpacking initramfs...
    [ 0.774193] Freeing initrd memory: 3700k freed
    [ 0.776235] PCI-DMA: Disabling AGP.
    [ 0.776306] PCI-DMA: aperture base @ c4000000 size 65536 KB
    [ 0.776307] PCI-DMA: using GART IOMMU.
    [ 0.776309] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
    [ 0.779581] LVT offset 1 assigned for vector 0x400
    [ 0.779589] IBS: LVT offset 1 assigned
    [ 0.779613] perf: AMD IBS detected (0x0000001f)
    [ 0.779743] audit: initializing netlink socket (disabled)
    [ 0.779753] type=2000 audit(1348861535.663:1): initialized
    [ 0.789269] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.790783] VFS: Disk quotas dquot_6.5.2
    [ 0.790820] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.790894] msgmni has been set to 7909
    [ 0.791048] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.791075] io scheduler noop registered
    [ 0.791076] io scheduler deadline registered
    [ 0.791112] io scheduler cfq registered (default)
    [ 0.791228] pcieport 0000:00:02.0: irq 40 for MSI/MSI-X
    [ 0.791319] pcieport 0000:00:0a.0: irq 41 for MSI/MSI-X
    [ 0.791449] GHES: HEST is not enabled!
    [ 0.791503] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.812101] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.832955] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.833141] Linux agpgart interface v0.103
    [ 0.833180] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
    [ 0.833181] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
    [ 0.833304] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.833378] mousedev: PS/2 mouse device common for all mice
    [ 0.833425] rtc_cmos 00:05: RTC can wake from S4
    [ 0.833539] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
    [ 0.833571] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
    [ 0.833577] cpuidle: using governor ladder
    [ 0.833578] cpuidle: using governor menu
    [ 0.833689] drop_monitor: Initializing network drop monitor service
    [ 0.833749] TCP: cubic registered
    [ 0.833835] NET: Registered protocol family 10
    [ 0.833965] NET: Registered protocol family 17
    [ 0.833973] Key type dns_resolver registered
    [ 0.834070] PM: Hibernation image not present or could not be loaded.
    [ 0.834076] registered taskstats version 1
    [ 0.834539] rtc_cmos 00:05: setting system clock to 2012-09-28 19:45:35 UTC (1348861535)
    [ 0.835479] Freeing unused kernel memory: 760k freed
    [ 0.835631] Write protecting the kernel read-only data: 8192k
    [ 0.839453] Freeing unused kernel memory: 1488k freed
    [ 0.841313] Freeing unused kernel memory: 612k freed
    [ 0.848497] systemd-udevd[70]: starting version 189
    [ 0.851135] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 0.861403] Floppy drive(s): fd0 is 1.44M
    [ 0.868797] ACPI: bus type usb registered
    [ 0.868817] usbcore: registered new interface driver usbfs
    [ 0.868825] usbcore: registered new interface driver hub
    [ 0.868995] usbcore: registered new device driver usb
    [ 0.869288] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.869717] ehci_hcd 0000:00:12.2: EHCI Host Controller
    [ 0.869754] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
    [ 0.869763] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
    [ 0.869785] QUIRK: Enable AMD PLL fix
    [ 0.869787] ehci_hcd 0000:00:12.2: applying AMD SB600/SB700 USB freeze workaround
    [ 0.869799] ehci_hcd 0000:00:12.2: debug port 1
    [ 0.869827] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe02c000
    [ 0.871224] SCSI subsystem initialized
    [ 0.872843] libata version 3.00 loaded.
    [ 0.874245] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [ 0.877166] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
    [ 0.877278] hub 1-0:1.0: USB hub found
    [ 0.877281] hub 1-0:1.0: 6 ports detected
    [ 0.878035] FDC 0 is a post-1991 82077
    [ 0.878198] ehci_hcd 0000:00:13.2: EHCI Host Controller
    [ 0.878204] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
    [ 0.878211] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
    [ 0.878223] ehci_hcd 0000:00:13.2: applying AMD SB600/SB700 USB freeze workaround
    [ 0.878238] ehci_hcd 0000:00:13.2: debug port 1
    [ 0.878264] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe029000
    [ 0.887161] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
    [ 0.887266] hub 2-0:1.0: USB hub found
    [ 0.887269] hub 2-0:1.0: 6 ports detected
    [ 0.887719] ahci 0000:00:11.0: version 3.0
    [ 0.887841] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
    [ 0.887844] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc
    [ 0.888332] scsi0 : ahci
    [ 0.888396] scsi1 : ahci
    [ 0.888447] scsi2 : ahci
    [ 0.888494] scsi3 : ahci
    [ 0.888576] ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22
    [ 0.888578] ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22
    [ 0.888580] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22
    [ 0.888583] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22
    [ 0.888675] ohci_hcd 0000:00:12.0: OHCI Host Controller
    [ 0.888681] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 3
    [ 0.888719] ohci_hcd 0000:00:12.0: irq 16, io mem 0xfe02e000
    [ 0.944618] hub 3-0:1.0: USB hub found
    [ 0.944624] hub 3-0:1.0: 3 ports detected
    [ 0.944916] ohci_hcd 0000:00:12.1: OHCI Host Controller
    [ 0.944922] ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 4
    [ 0.944936] ohci_hcd 0000:00:12.1: irq 16, io mem 0xfe02d000
    [ 1.001279] hub 4-0:1.0: USB hub found
    [ 1.001285] hub 4-0:1.0: 3 ports detected
    [ 1.001404] ohci_hcd 0000:00:13.0: OHCI Host Controller
    [ 1.001409] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
    [ 1.001435] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe02b000
    [ 1.057932] hub 5-0:1.0: USB hub found
    [ 1.057938] hub 5-0:1.0: 3 ports detected
    [ 1.058071] ohci_hcd 0000:00:13.1: OHCI Host Controller
    [ 1.058076] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 6
    [ 1.058089] ohci_hcd 0000:00:13.1: irq 18, io mem 0xfe02a000
    [ 1.114589] hub 6-0:1.0: USB hub found
    [ 1.114595] hub 6-0:1.0: 3 ports detected
    [ 1.114705] ohci_hcd 0000:00:14.5: OHCI Host Controller
    [ 1.114710] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 7
    [ 1.114723] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe028000
    [ 1.171271] hub 7-0:1.0: USB hub found
    [ 1.171277] hub 7-0:1.0: 2 ports detected
    [ 1.207184] ata3: SATA link down (SStatus 0 SControl 300)
    [ 1.207225] ata4: SATA link down (SStatus 0 SControl 300)
    [ 1.300449] usb 2-4: new high-speed USB device number 3 using ehci_hcd
    [ 1.373774] ata2: softreset failed (device not ready)
    [ 1.373843] ata2: applying PMP SRST workaround and retrying
    [ 1.373866] ata1: softreset failed (device not ready)
    [ 1.373934] ata1: applying PMP SRST workaround and retrying
    [ 1.425928] hub 2-4:1.0: USB hub found
    [ 1.426276] hub 2-4:1.0: 4 ports detected
    [ 1.540428] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 1.540459] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 1.541221] ata1.00: ATA-8: WDC WD3200AAKS-75L9A0, 01.03E01, max UDMA/133
    [ 1.541224] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    [ 1.542034] ata1.00: configured for UDMA/133
    [ 1.542185] scsi 0:0:0:0: Direct-Access ATA WDC WD3200AAKS-7 01.0 PQ: 0 ANSI: 5
    [ 1.552905] ata2.00: ATAPI: LITE-ON DVDRW LH-20A1L, BL05, max UDMA/100
    [ 1.565919] ata2.00: configured for UDMA/100
    [ 1.567862] scsi 1:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1L BL05 PQ: 0 ANSI: 5
    [ 1.570090] scsi4 : pata_atiixp
    [ 1.570937] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
    [ 1.570968] sd 0:0:0:0: [sda] Write Protect is off
    [ 1.570970] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 1.570992] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 1.571032] scsi5 : pata_atiixp
    [ 1.571566] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14
    [ 1.571568] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15
    [ 1.574704] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
    [ 1.574707] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 1.574836] sr 1:0:0:0: Attached scsi CD-ROM sr0
    [ 1.583928] sda: sda1 sda2 sda3 sda4
    [ 1.584257] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 1.677054] usb 5-3: new full-speed USB device number 2 using ohci_hcd
    [ 1.780379] Refined TSC clocksource calibration: 2812.808 MHz.
    [ 1.780391] Switching to clocksource tsc
    [ 1.850813] usbcore: registered new interface driver usbhid
    [ 1.850814] usbhid: USB HID core driver
    [ 1.851297] input: HID 1d57:0005 as /devices/pci0000:00/0000:00:13.0/usb5/5-3/5-3:1.0/input/input1
    [ 1.851380] hid-generic 0003:1D57:0005.0001: input,hidraw0: USB HID v1.10 Mouse [HID 1d57:0005] on usb-0000:00:13.0-3/input0
    [ 1.914434] usb 2-4.4: new high-speed USB device number 4 using ehci_hcd
    [ 1.925431] device-mapper: uevent: version 1.0.3
    [ 1.925535] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
    [ 2.294145] REISERFS (device dm-3): found reiserfs format "3.6" with standard journal
    [ 2.294160] REISERFS (device dm-3): using ordered data mode
    [ 2.294161] reiserfs: using flush barriers
    [ 2.294331] REISERFS (device dm-3): journal params: device dm-3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    [ 2.294793] REISERFS (device dm-3): checking transaction log (dm-3)
    [ 2.328438] REISERFS (device dm-3): Using r5 hash to sort names
    [ 3.521243] systemd-udevd[196]: starting version 192
    [ 3.731543] vboxdrv: Found 3 processor cores.
    [ 3.731692] vboxdrv: fAsync=0 offMin=0x421 offMax=0x19b7
    [ 3.731735] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
    [ 3.731736] vboxdrv: Successfully loaded version 4.2.0_OSE (interface 0x001a0004).
    [ 4.078334] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
    [ 4.078340] ACPI: Power Button [PWRB]
    [ 4.078389] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    [ 4.078391] ACPI: Power Button [PWRF]
    [ 4.118249] wmi: Mapper loaded
    [ 4.264495] sp5100_tco: SP5100 TCO WatchDog Timer Driver v0.01
    [ 4.264551] sp5100_tco: mmio address 0xfec000f0 already in use
    [ 4.266129] EDAC MC: Ver: 2.1.0
    [ 4.308369] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/input/input4
    [ 4.326814] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input5
    [ 4.326881] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input6
    [ 4.326938] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
    [ 4.326984] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
    [ 4.327034] input: HDA ATI SB Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
    [ 4.327093] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input10
    [ 4.327137] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input11
    [ 4.327181] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input12
    [ 4.331081] k10temp 0000:00:18.3: unreliable CPU thermal sensor; monitoring disabled
    [ 4.331239] ACPI Warning: 0x0000000000000b00-0x0000000000000b07 SystemIO conflicts with Region \SOR1 1 (20120320/utaddress-251)
    [ 4.331244] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 4.370081] firewire_ohci 0000:03:0e.0: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x2
    [ 4.370182] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
    [ 4.370266] r8169 0000:02:00.0: irq 42 for MSI/MSI-X
    [ 4.370532] r8169 0000:02:00.0: eth0: RTL8168c/8111c at 0xffffc90000656000, 00:24:1d:14:eb:1c, XID 1c4000c0 IRQ 42
    [ 4.370534] r8169 0000:02:00.0: eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
    [ 4.460371] MCE: In-kernel MCE decoding enabled.
    [ 4.461269] AMD64 EDAC driver v3.4.0
    [ 4.461326] EDAC amd64: DRAM ECC disabled.
    [ 4.461332] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
    Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
    (Note that use of the override may cause unknown side effects.)
    [ 4.681980] cfg80211: Calling CRDA to update world regulatory domain
    [ 4.870047] firewire_core 0000:03:0e.0: created device fw0: GUID 0019f1ec0000241d, S400
    [ 4.906613] ath5k 0000:03:07.0: registered as 'phy0'
    [ 5.157960] kvm: Nested Virtualization enabled
    [ 5.157964] kvm: Nested Paging enabled
    [ 5.212068] powernow-k8: Found 1 AMD Phenom(tm) II X3 720 Processor (3 cpu cores) (version 2.20.00)
    [ 5.212100] powernow-k8: 0 : pstate 0 (2800 MHz)
    [ 5.212101] powernow-k8: 1 : pstate 1 (2100 MHz)
    [ 5.212102] powernow-k8: 2 : pstate 2 (1600 MHz)
    [ 5.212103] powernow-k8: 3 : pstate 3 (800 MHz)
    [ 5.445767] microcode: CPU0: patch_level=0x01000086
    [ 5.513053] ath: EEPROM regdomain: 0x809c
    [ 5.513060] ath: EEPROM indicates we should expect a country code
    [ 5.513064] ath: doing EEPROM country->regdmn map search
    [ 5.513067] ath: country maps to regdmn code: 0x52
    [ 5.513070] ath: Country alpha2 being used: CN
    [ 5.513073] ath: Regpair used: 0x52
    [ 5.720324] microcode: failed to load file amd-ucode/microcode_amd.bin
    [ 5.720419] microcode: CPU1: patch_level=0x01000086
    [ 5.721269] microcode: failed to load file amd-ucode/microcode_amd.bin
    [ 5.721373] microcode: CPU2: patch_level=0x01000086
    [ 5.722356] microcode: failed to load file amd-ucode/microcode_amd.bin
    [ 5.722563] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 5.801835] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
    [ 5.802304] ath5k: phy0: Atheros AR2413 chip found (MAC: 0x78, PHY: 0x45)
    [ 6.296710] nvidia: module license 'NVIDIA' taints kernel.
    [ 6.296714] Disabling lock debugging due to kernel taint
    [ 6.309419] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
    [ 6.309823] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.51 Tue Sep 18 17:16:56 PDT 2012
    [ 6.321474] Linux media interface: v0.10
    [ 6.384863] Linux video capture interface: v2.00
    [ 6.452628] uvcvideo: Found UVC 1.00 device <unnamed> (046d:0808)
    [ 6.469190] input: UVC Camera (046d:0808) as /devices/pci0000:00/0000:00:13.2/usb2/2-4/2-4.4/2-4.4:1.0/input/input13
    [ 6.469404] usbcore: registered new interface driver uvcvideo
    [ 6.469407] USB Video Class driver (1.1.1)
    [ 7.020908] usbcore: registered new interface driver snd-usb-audio
    [ 7.051400] set resolution quirk: cval->res = 384
    [ 8.232297] reiserfs: enabling write barrier flush mode
    [ 8.511269] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
    [ 8.515067] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
    [ 8.556782] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
    [ 10.739934] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 11.452652] wlan0: authenticate with 00:1f:c6:3d:84:ba
    [ 11.461052] wlan0: send auth to 00:1f:c6:3d:84:ba (try 1/3)
    [ 11.462516] wlan0: authenticated
    [ 11.469067] wlan0: associate with 00:1f:c6:3d:84:ba (try 1/3)
    [ 11.470817] wlan0: RX AssocResp from 00:1f:c6:3d:84:ba (capab=0x401 status=0 aid=3)
    [ 11.471130] wlan0: associated
    [ 11.471521] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    [ 24.567793] NVRM: GPU at 0000:01:00: GPU-ac314c58-0b61-fb24-fa28-bac76d8e581b
    [ 27.419761] fuse init (API version 7.19)
    [ 31.119563] EXT4-fs (dm-2): re-mounted. Opts: commit=0
    [ 2088.845650] ata1.00: exception Emask 0x50 SAct 0x78000ffc SErr 0x400800 action 0x6 frozen
    [ 2088.845660] ata1.00: irq_stat 0x08000000, interface fatal error
    [ 2088.845667] ata1: SError: { HostInt Handshk }
    [ 2088.845674] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845687] ata1.00: cmd 61/08:10:97:ae:07/00:00:1a:00:00/40 tag 2 ncq 4096 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845694] ata1.00: status: { DRDY }
    [ 2088.845699] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845711] ata1.00: cmd 61/08:18:b7:ae:07/00:00:1a:00:00/40 tag 3 ncq 4096 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845716] ata1.00: status: { DRDY }
    [ 2088.845721] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845732] ata1.00: cmd 61/20:20:bf:ae:07/00:00:1a:00:00/40 tag 4 ncq 16384 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845737] ata1.00: status: { DRDY }
    [ 2088.845742] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845753] ata1.00: cmd 61/c8:28:df:ae:07/00:00:1a:00:00/40 tag 5 ncq 102400 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845758] ata1.00: status: { DRDY }
    [ 2088.845763] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845774] ata1.00: cmd 61/90:30:a7:af:07/00:00:1a:00:00/40 tag 6 ncq 73728 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845779] ata1.00: status: { DRDY }
    [ 2088.845783] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845795] ata1.00: cmd 61/b8:38:37:b0:07/00:00:1a:00:00/40 tag 7 ncq 94208 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845800] ata1.00: status: { DRDY }
    [ 2088.845804] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845815] ata1.00: cmd 61/a8:40:ef:b0:07/00:00:1a:00:00/40 tag 8 ncq 86016 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845820] ata1.00: status: { DRDY }
    [ 2088.845825] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845836] ata1.00: cmd 61/80:48:97:b1:07/00:00:1a:00:00/40 tag 9 ncq 65536 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845841] ata1.00: status: { DRDY }
    [ 2088.845845] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845857] ata1.00: cmd 61/b0:50:17:b2:07/00:00:1a:00:00/40 tag 10 ncq 90112 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845862] ata1.00: status: { DRDY }
    [ 2088.845867] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845878] ata1.00: cmd 61/d8:58:c7:b2:07/00:00:1a:00:00/40 tag 11 ncq 110592 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845883] ata1.00: status: { DRDY }
    [ 2088.845889] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845900] ata1.00: cmd 61/08:d8:8f:ae:07/00:00:1a:00:00/40 tag 27 ncq 4096 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845905] ata1.00: status: { DRDY }
    [ 2088.845910] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845922] ata1.00: cmd 61/08:e0:9f:ae:07/00:00:1a:00:00/40 tag 28 ncq 4096 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845927] ata1.00: status: { DRDY }
    [ 2088.845931] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845942] ata1.00: cmd 61/08:e8:a7:ae:07/00:00:1a:00:00/40 tag 29 ncq 4096 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845947] ata1.00: status: { DRDY }
    [ 2088.845954] ata1.00: failed command: WRITE FPDMA QUEUED
    [ 2088.845965] ata1.00: cmd 61/08:f0:af:ae:07/00:00:1a:00:00/40 tag 30 ncq 4096 out
    res 40/00:5c:c7:b2:07/00:00:1a:00:00/40 Emask 0x50 (ATA bus error)
    [ 2088.845970] ata1.00: status: { DRDY }
    [ 2088.845978] ata1: hard resetting link
    [ 2089.329937] ata1: softreset failed (device not ready)
    [ 2089.329948] ata1: applying PMP SRST workaround and retrying
    [ 2089.496590] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 2089.498245] ata1.00: configured for UDMA/133
    [ 2089.509941] sd 0:0:0:0: [sda]
    [ 2089.509950] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.509956] sd 0:0:0:0: [sda]
    [ 2089.509959] Sense Key : 0xb [current] [descriptor]
    [ 2089.509966] Descriptor sense data with sense descriptors (in hex):
    [ 2089.509969] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.509987] 1a 07 b2 c7
    [ 2089.509996] sd 0:0:0:0: [sda]
    [ 2089.509999] ASC=0x0 ASCQ=0x0
    [ 2089.510004] sd 0:0:0:0: [sda] CDB:
    [ 2089.510006] cdb[0]=0x2a: 2a 00 1a 07 ae 97 00 00 08 00
    [ 2089.510021] end_request: I/O error, dev sda, sector 436711063
    [ 2089.510032] Buffer I/O error on device dm-3, logical block 631
    [ 2089.510035] lost page write due to I/O error on dm-3
    [ 2089.510058] sd 0:0:0:0: [sda]
    [ 2089.510061] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.510066] sd 0:0:0:0: [sda]
    [ 2089.510068] Sense Key : 0xb [current] [descriptor]
    [ 2089.510073] Descriptor sense data with sense descriptors (in hex):
    [ 2089.510075] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.510091] 1a 07 b2 c7
    [ 2089.510099] sd 0:0:0:0: [sda]
    [ 2089.510101] ASC=0x0 ASCQ=0x0
    [ 2089.510106] sd 0:0:0:0: [sda] CDB:
    [ 2089.510108] cdb[0]=0x2a: 2a 00 1a 07 ae b7 00 00 08 00
    [ 2089.510121] end_request: I/O error, dev sda, sector 436711095
    [ 2089.510126] Buffer I/O error on device dm-3, logical block 635
    [ 2089.510129] lost page write due to I/O error on dm-3
    [ 2089.510140] sd 0:0:0:0: [sda]
    [ 2089.510142] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.510146] sd 0:0:0:0: [sda]
    [ 2089.510149] Sense Key : 0xb [current] [descriptor]
    [ 2089.510153] Descriptor sense data with sense descriptors (in hex):
    [ 2089.510155] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.510171] 1a 07 b2 c7
    [ 2089.510178] sd 0:0:0:0: [sda]
    [ 2089.510181] ASC=0x0 ASCQ=0x0
    [ 2089.510185] sd 0:0:0:0: [sda] CDB:
    [ 2089.510187] cdb[0]=0x2a: 2a 00 1a 07 ae bf 00 00 20 00
    [ 2089.510200] end_request: I/O error, dev sda, sector 436711103
    [ 2089.510205] Buffer I/O error on device dm-3, logical block 636
    [ 2089.510208] lost page write due to I/O error on dm-3
    [ 2089.510212] Buffer I/O error on device dm-3, logical block 637
    [ 2089.510215] lost page write due to I/O error on dm-3
    [ 2089.510220] Buffer I/O error on device dm-3, logical block 638
    [ 2089.510222] lost page write due to I/O error on dm-3
    [ 2089.510227] Buffer I/O error on device dm-3, logical block 639
    [ 2089.510230] lost page write due to I/O error on dm-3
    [ 2089.510245] sd 0:0:0:0: [sda]
    [ 2089.510248] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.510252] sd 0:0:0:0: [sda]
    [ 2089.510254] Sense Key : 0xb [current] [descriptor]
    [ 2089.510258] Descriptor sense data with sense descriptors (in hex):
    [ 2089.510261] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.510276] 1a 07 b2 c7
    [ 2089.510284] sd 0:0:0:0: [sda]
    [ 2089.510286] ASC=0x0 ASCQ=0x0
    [ 2089.510290] sd 0:0:0:0: [sda] CDB:
    [ 2089.510293] cdb[0]=0x2a: 2a 00 1a 07 ae df 00 00 c8 00
    [ 2089.510305] end_request: I/O error, dev sda, sector 436711135
    [ 2089.510310] Buffer I/O error on device dm-3, logical block 640
    [ 2089.510313] lost page write due to I/O error on dm-3
    [ 2089.510317] Buffer I/O error on device dm-3, logical block 641
    [ 2089.510320] lost page write due to I/O error on dm-3
    [ 2089.510325] Buffer I/O error on device dm-3, logical block 642
    [ 2089.510327] lost page write due to I/O error on dm-3
    [ 2089.510332] Buffer I/O error on device dm-3, logical block 643
    [ 2089.510335] lost page write due to I/O error on dm-3
    [ 2089.510400] sd 0:0:0:0: [sda]
    [ 2089.510403] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.510407] sd 0:0:0:0: [sda]
    [ 2089.510409] Sense Key : 0xb [current] [descriptor]
    [ 2089.510414] Descriptor sense data with sense descriptors (in hex):
    [ 2089.510416] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.510432] 1a 07 b2 c7
    [ 2089.510440] sd 0:0:0:0: [sda]
    [ 2089.510442] ASC=0x0 ASCQ=0x0
    [ 2089.510446] sd 0:0:0:0: [sda] CDB:
    [ 2089.510449] cdb[0]=0x2a: 2a 00 1a 07 af a7 00 00 90 00
    [ 2089.510461] end_request: I/O error, dev sda, sector 436711335
    [ 2089.510502] sd 0:0:0:0: [sda]
    [ 2089.510505] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.510509] sd 0:0:0:0: [sda]
    [ 2089.510511] Sense Key : 0xb [current] [descriptor]
    [ 2089.510515] Descriptor sense data with sense descriptors (in hex):
    [ 2089.510518] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.510533] 1a 07 b2 c7
    [ 2089.510541] sd 0:0:0:0: [sda]
    [ 2089.510543] ASC=0x0 ASCQ=0x0
    [ 2089.510548] sd 0:0:0:0: [sda] CDB:
    [ 2089.510550] cdb[0]=0x2a: 2a 00 1a 07 b0 37 00 00 b8 00
    [ 2089.510563] end_request: I/O error, dev sda, sector 436711479
    [ 2089.510610] sd 0:0:0:0: [sda]
    [ 2089.510613] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.510617] sd 0:0:0:0: [sda]
    [ 2089.510619] Sense Key : 0xb [current] [descriptor]
    [ 2089.510623] Descriptor sense data with sense descriptors (in hex):
    [ 2089.510626] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.510641] 1a 07 b2 c7
    [ 2089.510649] sd 0:0:0:0: [sda]
    [ 2089.510651] ASC=0x0 ASCQ=0x0
    [ 2089.510656] sd 0:0:0:0: [sda] CDB:
    [ 2089.510658] cdb[0]=0x2a: 2a 00 1a 07 b0 ef 00 00 a8 00
    [ 2089.510670] end_request: I/O error, dev sda, sector 436711663
    [ 2089.510713] sd 0:0:0:0: [sda]
    [ 2089.510716] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.510720] sd 0:0:0:0: [sda]
    [ 2089.510722] Sense Key : 0xb [current] [descriptor]
    [ 2089.510727] Descriptor sense data with sense descriptors (in hex):
    [ 2089.510729] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.510744] 1a 07 b2 c7
    [ 2089.510752] sd 0:0:0:0: [sda]
    [ 2089.510754] ASC=0x0 ASCQ=0x0
    [ 2089.510759] sd 0:0:0:0: [sda] CDB:
    [ 2089.510761] cdb[0]=0x2a: 2a 00 1a 07 b1 97 00 00 80 00
    [ 2089.510774] end_request: I/O error, dev sda, sector 436711831
    [ 2089.510812] sd 0:0:0:0: [sda]
    [ 2089.510815] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.510819] sd 0:0:0:0: [sda]
    [ 2089.510821] Sense Key : 0xb [current] [descriptor]
    [ 2089.510825] Descriptor sense data with sense descriptors (in hex):
    [ 2089.510828] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.510843] 1a 07 b2 c7
    [ 2089.510851] sd 0:0:0:0: [sda]
    [ 2089.510854] ASC=0x0 ASCQ=0x0
    [ 2089.510858] sd 0:0:0:0: [sda] CDB:
    [ 2089.510860] cdb[0]=0x2a: 2a 00 1a 07 b2 17 00 00 b0 00
    [ 2089.510873] end_request: I/O error, dev sda, sector 436711959
    [ 2089.510919] sd 0:0:0:0: [sda]
    [ 2089.510922] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.510926] sd 0:0:0:0: [sda]
    [ 2089.510928] Sense Key : 0xb [current] [descriptor]
    [ 2089.510933] Descriptor sense data with sense descriptors (in hex):
    [ 2089.510935] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.510951] 1a 07 b2 c7
    [ 2089.510959] sd 0:0:0:0: [sda]
    [ 2089.510961] ASC=0x0 ASCQ=0x0
    [ 2089.510966] sd 0:0:0:0: [sda] CDB:
    [ 2089.510968] cdb[0]=0x2a: 2a 00 1a 07 b2 c7 00 00 d8 00
    [ 2089.510980] end_request: I/O error, dev sda, sector 436712135
    [ 2089.511030] sd 0:0:0:0: [sda]
    [ 2089.511033] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.511037] sd 0:0:0:0: [sda]
    [ 2089.511039] Sense Key : 0xb [current] [descriptor]
    [ 2089.511043] Descriptor sense data with sense descriptors (in hex):
    [ 2089.511046] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.511061] 1a 07 b2 c7
    [ 2089.511069] sd 0:0:0:0: [sda]
    [ 2089.511071] ASC=0x0 ASCQ=0x0
    [ 2089.511076] sd 0:0:0:0: [sda] CDB:
    [ 2089.511078] cdb[0]=0x2a: 2a 00 1a 07 ae 8f 00 00 08 00
    [ 2089.511090] end_request: I/O error, dev sda, sector 436711055
    [ 2089.511111] sd 0:0:0:0: [sda]
    [ 2089.511114] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.511118] sd 0:0:0:0: [sda]
    [ 2089.511120] Sense Key : 0xb [current] [descriptor]
    [ 2089.511125] Descriptor sense data with sense descriptors (in hex):
    [ 2089.511128] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.511144] 1a 07 b2 c7
    [ 2089.511151] sd 0:0:0:0: [sda]
    [ 2089.511154] ASC=0x0 ASCQ=0x0
    [ 2089.511158] sd 0:0:0:0: [sda] CDB:
    [ 2089.511160] cdb[0]=0x2a: 2a 00 1a 07 ae 9f 00 00 08 00
    [ 2089.511173] end_request: I/O error, dev sda, sector 436711071
    [ 2089.511188] sd 0:0:0:0: [sda]
    [ 2089.511191] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.511195] sd 0:0:0:0: [sda]
    [ 2089.511197] Sense Key : 0xb [current] [descriptor]
    [ 2089.511201] Descriptor sense data with sense descriptors (in hex):
    [ 2089.511204] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.511219] 1a 07 b2 c7
    [ 2089.511227] sd 0:0:0:0: [sda]
    [ 2089.511230] ASC=0x0 ASCQ=0x0
    [ 2089.511234] sd 0:0:0:0: [sda] CDB:
    [ 2089.511236] cdb[0]=0x2a: 2a 00 1a 07 ae a7 00 00 08 00
    [ 2089.511249] end_request: I/O error, dev sda, sector 436711079
    [ 2089.511263] sd 0:0:0:0: [sda]
    [ 2089.511266] Result: hostbyte=0x00 driverbyte=0x08
    [ 2089.511270] sd 0:0:0:0: [sda]
    [ 2089.511272] Sense Key : 0xb [current] [descriptor]
    [ 2089.511277] Descriptor sense data with sense descriptors (in hex):
    [ 2089.511279] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 2089.511295] 1a 07 b2 c7
    [ 2089.511302] sd 0:0:0:0: [sda]
    [ 2089.511305] ASC=0x0 ASCQ=0x0
    [ 2089.511309] sd 0:0:0:0: [sda] CDB:
    [ 2089.511311] cdb[0]=0x2a: 2a 00 1a 07 ae af 00 00 08 00
    [ 2089.511324] end_request: I/O error, dev sda, sector 436711087
    [ 2089.511343] ata1: EH complete
    [ 2089.511517] REISERFS abort (device dm-3): Journal write error in flush_commit_list
    error.log (only part related to the current session):
    Sep 28 20:20:21 localhost kernel: [ 2088.845650] ata1.00: exception Emask 0x50 SAct 0x78000ffc SErr 0x400800 action 0x6 frozen
    Sep 28 20:20:21 localhost kernel: [ 2088.845660] ata1.00: irq_stat 0x08000000, interface fatal error
    Sep 28 20:20:21 localh

    uzsolt wrote:
    I've same problem with an asus laptop, with one hdd. On the device I've some partitions (home, root, backup, var) but this error appears with 'home' only. Sometimes the mount options turns into "read-only", but only on home-partition (ext4, but root, var and a download-directory is ext4 too but they works well).
    I found this: https://bbs.archlinux.org/viewtopic.php … 9#p1052099 - I hope this helps for me - and for you too
    Errors in logs:
    Dec 02 09:44:03 [kernel] [ 666.911555] ata1.00: exception Emask 0x50 SAct 0x4 SErr 0x400800 action 0x6 frozen
    Dec 02 09:44:03 [kernel] [ 666.911561] ata1.00: irq_stat 0x08000000, interface fatal error
    Dec 02 09:44:03 [kernel] [ 666.911564] ata1: SError: { HostInt Handshk }
    Dec 02 09:44:03 [kernel] [ 666.911568] ata1.00: failed command: WRITE FPDMA QUEUED
    Dec 02 09:44:03 [kernel] [ 666.911574] ata1.00: cmd 61/68:10:53:25:2a/00:00:04:00:00/40 tag 2 ncq 53248 out
    Dec 02 09:44:03 [kernel] [ 666.911574] res 40/00:10:53:25:2a/00:00:04:00:00/40 Emask 0x50 (ATA bus error)
    Dec 02 09:44:03 [kernel] [ 666.911577] ata1.00: status: { DRDY }
    Dec 02 09:44:03 [kernel] [ 666.911583] ata1: hard resetting link
    Dec 02 09:44:03 [kernel] [ 667.396660] ata1: softreset failed (device not ready)
    Dec 02 09:44:03 [kernel] [ 667.396668] ata1: applying PMP SRST workaround and retrying
    Dec 02 09:44:03 [kernel] [ 667.563375] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    Dec 02 09:44:03 [kernel] [ 667.614772] ata1.00: configured for UDMA/133
    Dec 02 09:44:03 [kernel] [ 667.614796] sd 0:0:0:0: [sda]
    Dec 02 09:44:03 [kernel] [ 667.614798] Result: hostbyte=0x00 driverbyte=0x08
    Dec 02 09:44:03 [kernel] [ 667.614801] sd 0:0:0:0: [sda]
    Dec 02 09:44:03 [kernel] [ 667.614802] Sense Key : 0xb [current] [descriptor]
    Dec 02 09:44:03 [kernel] [ 667.614806] Descriptor sense data with sense descriptors (in hex):
    Dec 02 09:44:03 [kernel] [ 667.614808] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    Dec 02 09:44:03 [kernel] [ 667.614816] 04 2a 25 53
    Dec 02 09:44:03 [kernel] [ 667.614821] sd 0:0:0:0: [sda]
    Dec 02 09:44:03 [kernel] [ 667.614822] ASC=0x0 ASCQ=0x0
    Dec 02 09:44:03 [kernel] [ 667.614825] sd 0:0:0:0: [sda] CDB:
    Dec 02 09:44:03 [kernel] [ 667.614827] cdb[0]=0x2a: 2a 00 04 2a 25 53 00 00 68 00
    Dec 02 09:44:03 [kernel] [ 667.614834] end_request: I/O error, dev sda, sector 69870931
    Dec 02 09:44:03 [kernel] [ 667.614862] ata1: EH complete
    Dec 02 09:44:03 [kernel] [ 667.614949] Aborting journal on device sda3-8.
    Dec 02 09:44:03 [kernel] [ 667.614962] EXT4-fs error (device sda3) in ext4_reserve_inode_write:4550: Journal has aborted
    Dec 02 09:44:04 [kernel] [ 667.692734] EXT4-fs error (device sda3) in ext4_dirty_inode:4669: Journal has aborted
    Dec 02 09:44:04 [kernel] [ 667.720681] EXT4-fs error (device sda3): ext4_journal_start_sb:349: Detected aborted journal
    Dec 02 09:44:04 [kernel] [ 667.720690] EXT4-fs (sda3): Remounting filesystem read-only
    Dec 02 09:44:04 [kernel] [ 667.721798] EXT4-fs error (device sda3): ext4_journal_start_sb:349: Detected aborted journal
    Dec 02 09:44:30 [kernel] [ 694.098612] ata1.00: exception Emask 0x50 SAct 0x40 SErr 0x800 action 0x6 frozen
    Dec 02 09:44:30 [kernel] [ 694.098622] ata1.00: irq_stat 0x08000000, interface fatal error
    Dec 02 09:44:30 [kernel] [ 694.098627] ata1: SError: { HostInt }
    Dec 02 09:44:30 [kernel] [ 694.098635] ata1.00: failed command: WRITE FPDMA QUEUED
    Dec 02 09:44:30 [kernel] [ 694.098647] ata1.00: cmd 61/08:30:53:a6:e5/00:00:05:00:00/40 tag 6 ncq 4096 out
    Dec 02 09:44:30 [kernel] [ 694.098647] res 40/00:30:53:a6:e5/00:00:05:00:00/40 Emask 0x50 (ATA bus error)
    Dec 02 09:44:30 [kernel] [ 694.098653] ata1.00: status: { DRDY }
    Dec 02 09:44:30 [kernel] [ 694.098663] ata1: hard resetting link
    Dec 02 09:44:30 [kernel] [ 694.583317] ata1: softreset failed (device not ready)
    Dec 02 09:44:30 [kernel] [ 694.583328] ata1: applying PMP SRST workaround and retrying
    Dec 02 09:44:31 [kernel] [ 694.749997] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    Dec 02 09:44:31 [kernel] [ 694.804387] ata1.00: configured for UDMA/133
    Dec 02 09:44:31 [kernel] [ 694.804425] sd 0:0:0:0: [sda]
    Dec 02 09:44:31 [kernel] [ 694.804428] Result: hostbyte=0x00 driverbyte=0x08
    Dec 02 09:44:31 [kernel] [ 694.804434] sd 0:0:0:0: [sda]
    Dec 02 09:44:31 [kernel] [ 694.804437] Sense Key : 0xb [current] [descriptor]
    Dec 02 09:44:31 [kernel] [ 694.804443] Descriptor sense data with sense descriptors (in hex):
    Dec 02 09:44:31 [kernel] [ 694.804447] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    Dec 02 09:44:31 [kernel] [ 694.804463] 05 e5 a6 53
    Dec 02 09:44:31 [kernel] [ 694.804472] sd 0:0:0:0: [sda]
    Dec 02 09:44:31 [kernel] [ 694.804475] ASC=0x0 ASCQ=0x0
    Dec 02 09:44:31 [kernel] [ 694.804480] sd 0:0:0:0: [sda] CDB:
    Dec 02 09:44:31 [kernel] [ 694.804482] cdb[0]=0x2a: 2a 00 05 e5 a6 53 00 00 08 00
    Dec 02 09:44:31 [kernel] [ 694.804497] end_request: I/O error, dev sda, sector 98936403
    Dec 02 09:44:31 [kernel] [ 694.804505] Buffer I/O error on device sda3, logical block 9437196
    Dec 02 09:44:31 [kernel] [ 694.804508] lost page write due to I/O error on sda3
    Dec 02 09:44:31 [kernel] [ 694.804537] ata1: EH complete
    The other partition works well on same disk as I wrote above.
    Is /home on /dev/sda3?

  • Time Machine - External Hard Drive Read only error

    Just recently got a Iomega 1TB MiniMax FireWire 800 USB 2.0 Desktop Hard Drive and used Time Machine to backup my computer. This was my first time using Time Machine and it successfully backed up 350 GBs. It continued to do backups every hour. When I turned my computer off and then turned it on the next day Time Machine wouldn't allow me to do a backup because it said the hard drive was read only. When I checked info it said it was read/write. I used disc utility to verify disc it said it could not verify disc do a disc repair. Disc repair failed and it said reformat disc. I erased the hard drive tried again and I got the same error message. The hard drive is formatted Mac OS Extended (Journaled). I searched this forum and the trouble shooting links and couldn't find anything on how to correct this. Any help on this problem would be appreciated.

    See the following:
    What to do if Time Machine reports you don't have permission
    This was posted in the Apple Discussions by V.K. I have only modified it slightly to be more generic.
    The problem seems to be that 10.5.6 changes permissions on a file so that even the root user doesn't have write peivileges. I have no idea why they did this. The workaround suggested in [an]other post will probably work, too, but i did something less drastic. Instead of deleting the file I changed permissions on it, and it worked just fine. An added benefit is that the permission change seems to stick, so you don't have to delete the file every time you change a drive.
    [Open the Terminal application in your Utilities folder. At the prompt [enter] the following command:
    sudo chmod 644 /volumes/"TM drive name"/.xxxxxxxxxxxx
    The name of the file .xxxxxxxxxxxx is based on the MAC address of your computer and will be different for every computer. Put the name of the TM drive in the above and keep the quotes.
    You'll have to enter your admin password (which you won't see) which is normal.
    This was edited by Kappy just for cleanup.
    Enable Finder to Show Invisible Files and Folders
    Open the Terminal application in your Utilities folder. At the prompt enter or paste the following command line then press RETURN.
    defaults write com.apple.finder AppleShowAllFiles TRUE
    To turn off the display of invisible files and folders enter or paste the following command line and press RETURN.
    defaults write com.apple.finder AppleShowAllFiles FALSE
    Alternatively you can use one of the numerous third-party utilities such as TinkerTool or ShowHideInvisibleFiles - VersionTracker or MacUpdate.
    Also, see User Tips for Time Machine for help with TM problems. Also you can select Mac Help from the Finder's Help menu and search for "time machine" to locate articles on how to use TM. See also Mac 101- Time Machine.
    Message was edited by: Kappy

  • External hard drive read-only?

    Just got a Macbook Pro last week and I have found that my external drive is read-only, where it used to work perfectly on my old Windows laptop.
    I can assume that the drive is formatted as NTFS from reading other posts, and that I must format it as FAT32 (I believe), but in the Disc Utility I do not see this option.
    Can someone aid with this slight problem? I seem to be heading in the right direction as I'm not too keen on using third-party applications to enable writing.
    Additionally, sometimes the drive will not connect (light stays red) but I assume that this is possibly related to the formatting issue at hand. Any suggestions?
    Thanks in advance

    It is FAT32.  For some reason, OS X refers to it just as "FAT".
    As AussieDJ indicated, you can use NTFS 3G.  This allows your Mac to write to NTFS formatted drives.  I personally have used this for quite a while and have never had issues.  I have seen some posts from people saying it can be problematic.  As I have never had a problem, I can't say specifically what issues might arise.  Apple does offer it directly on their download pages:
    http://www.apple.com/downloads/macosx/system_disk_utilities/ntfs3g.html

  • [Solved] Laptop Suspend puts Hard Drive into Read-Only

    My problem is that s2ram brings back X (and the virtual console, if I'm on one), but never the hard drive.
    s2ram -f -a 1 suspends just like s2ram -f. -a 2 and 3 just make a high pitched sound.
    I tried both http://wiki.archlinux.org/index.php/Suspend_to_RAM and http://wiki.archlinux.org/index.php/Pm-utils methods.
    I updated my BIOS drivers but that didn't help
    s2disk works perfectly.
    This is a COMPAQ Presario CQ60-215DX
    Here is my log of the trouble during resume:
    ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    sd 3:0:0:0: [sda] Starting disk
    ata4.00: qc timeout (cmd 0xec)
    ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata4.00: revalidation failed (errno=-5)
    ata3.00: qc timeout (cmd 0xa1)
    ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata3.00: revalidation failed (errno=-5)
    ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3.00: qc timeout (cmd 0xa1)
    ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata3.00: revalidation failed (errno=-5)
    ata3: limiting SATA link speed to 1.5 Gbps
    ata4.00: qc timeout (cmd 0xec)
    ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata4.00: revalidation failed (errno=-5)
    ata4: limiting SATA link speed to 1.5 Gbps
    ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    ata4: SATA link up <unknown> (SStatus 103 SControl 310)
    And my full log:
    Linux version 2.6.30-ARCH (root@T-POWA-LX) (gcc version 4.4.1 (GCC) ) #1 SMP PREEMPT Fri Jul 31 07:30:28 CEST 2009
    Command line: root=/dev/disk/by-uuid/9ae7dfa5-74b2-41e2-89bc-b344bbf47109 ro
    KERNEL supported cpus:
    Intel GenuineIntel
    AMD AuthenticAMD
    Centaur CentaurHauls
    libata version 3.00 loaded.
    pata_amd 0000:00:06.0: version 0.4.1
    pata_amd 0000:00:06.0: setting latency timer to 64
    scsi0 : pata_amd
    scsi1 : pata_amd
    ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x30c0 irq 14
    ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x30c8 irq 15
    ahci 0000:00:09.0: version 3.0
    ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 22
    ahci 0000:00:09.0: PCI INT A -> Link[LSI0] -> GSI 22 (level, low) -> IRQ 22
    ahci 0000:00:09.0: irq 25 for MSI/MSI-X
    ahci 0000:00:09.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl IDE mode
    ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pmp pio slum part
    ahci 0000:00:09.0: setting latency timer to 64
    scsi2 : ahci
    scsi3 : ahci
    ata3: SATA max UDMA/133 abar m8192@0xc0004000 port 0xc0004100 irq 25
    ata4: SATA max UDMA/133 abar m8192@0xc0004000 port 0xc0004180 irq 25
    ata2: port disabled. ignoring.
    Clocksource tsc unstable (delta = 4397486409693 ns)
    ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata4.00: ATA-8: TOSHIBA MK2555GSX, FG002C, max UDMA/100
    ata4.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
    ata4.00: configured for UDMA/100
    ata3.00: ATAPI: Optiarc DVD RW AD-7580S, FH03, max UDMA/100
    ata3.00: configured for UDMA/100
    scsi 2:0:0:0: CD-ROM Optiarc DVD RW AD-7580S FH03 PQ: 0 ANSI: 5
    scsi 3:0:0:0: Direct-Access ATA TOSHIBA MK2555GS FG00 PQ: 0 ANSI: 5
    Driver 'sr' needs updating - please use bus_type methods
    sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 2:0:0:0: Attached scsi CD-ROM sr0
    Driver 'sd' needs updating - please use bus_type methods
    sd 3:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
    sd 3:0:0:0: [sda] Write Protect is off
    sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda: sda1 sda2 sda3 < sda5 > sda4
    sd 3:0:0:0: [sda] Attached SCSI disk
    EXT4-fs: INFO: recovery required on readonly filesystem.
    EXT4-fs: write access will be enabled during recovery.
    EXT4-fs: barriers enabled
    kjournald2 starting: pid 569, dev sda2:8, commit interval 5 seconds
    EXT4-fs: delayed allocation enabled
    EXT4-fs: file extents enabled
    EXT4-fs: mballoc enabled
    EXT4-fs: sda2: orphan cleanup on readonly fs
    ext4_orphan_cleanup: deleting unreferenced inode 148384
    ext4_orphan_cleanup: deleting unreferenced inode 147907
    ext4_orphan_cleanup: deleting unreferenced inode 147903
    EXT4-fs: sda2: 3 orphan inodes deleted
    EXT4-fs: recovery complete.
    EXT4-fs: mounted filesystem sda2 with ordered data mode
    rtc_cmos 00:06: RTC can wake from S4
    rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
    udev: starting version 141
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    ACPI: AC Adapter [ADP1] (on-line)
    forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
    ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 21
    forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
    forcedeth 0000:00:0a.0: setting latency timer to 64
    sr 2:0:0:0: Attached scsi generic sg0 type 5
    sd 3:0:0:0: Attached scsi generic sg1 type 0
    usbcore: registered new device driver usb
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    cfg80211: Calling CRDA to update world regulatory domain
    input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
    ACPI: Power Button [PWRF]
    input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
    ACPI: Lid Switch [LID0]
    input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
    ACPI: Sleep Button [SLPB]
    input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
    ACPI: Power Button [PWRB]
    processor ACPI_CPU:00: registered as cooling_device0
    processor ACPI_CPU:01: registered as cooling_device1
    forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1f:16:74:cb:72
    forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt lnktim msi desc-v3
    ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 17
    ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 17 (level, low) -> IRQ 17
    ehci_hcd 0000:00:02.1: setting latency timer to 64
    ehci_hcd 0000:00:02.1: EHCI Host Controller
    ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:02.1: debug port 1
    ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
    ehci_hcd 0000:00:02.1: irq 17, io mem 0xc0007000
    ACPI: WMI: Mapper loaded
    ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 3 ports detected
    i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
    i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
    ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 17
    ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 17 (level, low) -> IRQ 17
    ohci_hcd 0000:00:02.0: setting latency timer to 64
    ohci_hcd 0000:00:02.0: OHCI Host Controller
    ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
    ohci_hcd 0000:00:02.0: irq 17, io mem 0xc0006000
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 3 ports detected
    ACPI: PCI Interrupt Link [Z011] enabled at IRQ 16
    ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z011] -> GSI 16 (level, low) -> IRQ 16
    ehci_hcd 0000:00:04.1: setting latency timer to 64
    ehci_hcd 0000:00:04.1: EHCI Host Controller
    ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 3
    ehci_hcd 0000:00:04.1: debug port 1
    ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
    ehci_hcd 0000:00:04.1: irq 16, io mem 0xc0007400
    ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 4 ports detected
    ACPI: PCI Interrupt Link [Z010] enabled at IRQ 16
    ohci_hcd 0000:00:04.0: PCI INT A -> Link[Z010] -> GSI 16 (level, low) -> IRQ 16
    ohci_hcd 0000:00:04.0: setting latency timer to 64
    ohci_hcd 0000:00:04.0: OHCI Host Controller
    ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
    ohci_hcd 0000:00:04.0: irq 16, io mem 0xc0008000
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 4 ports detected
    thermal LNXTHERM:01: registered as thermal_zone0
    ACPI: Thermal Zone [TZS0] (68 C)
    ACPI: Battery Slot [BAT0] (battery present)
    thermal LNXTHERM:02: registered as thermal_zone1
    ACPI: Thermal Zone [TZS1] (68 C)
    usb 1-1: new high speed USB device using ehci_hcd and address 2
    nvidia: module license 'NVIDIA' taints kernel.
    Disabling lock debugging due to kernel taint
    usb 1-1: configuration #1 chosen from 1 choice
    Synaptics Touchpad, model: 1, fw: 7.0, id: 0x1a0b1, caps: 0xd04711/0xa00000
    acpi device:13: registered as cooling_device2
    input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:10/device:11/input/input6
    ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
    usb 3-4: new high speed USB device using ehci_hcd and address 2
    input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input7
    ath5k 0000:07:00.0: PCI INT A -> Link[Z012] -> GSI 23 (level, low) -> IRQ 23
    ath5k 0000:07:00.0: setting latency timer to 64
    ath5k 0000:07:00.0: registered as 'phy0'
    usb 3-4: configuration #1 chosen from 1 choice
    ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 20
    nvidia 0000:02:00.0: PCI INT A -> Link[LGPU] -> GSI 20 (level, low) -> IRQ 20
    nvidia 0000:02:00.0: setting latency timer to 64
    NVRM: loading NVIDIA UNIX x86_64 Kernel Module 185.18.31 Tue Jul 28 17:52:27 PDT 2009
    EXT4 FS on sda2, internal journal on sda2:8
    Adding 3148700k swap on /dev/sda5. Priority:-1 extents:1 across:3148700k
    scsi 4:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
    sd 4:0:0:0: Attached scsi generic sg2 type 0
    usb-storage: device scan complete
    sd 4:0:0:0: [sdb] Attached SCSI removable disk
    scsi 5:0:0:0: Direct-Access USB Driver 0.00 PQ: 0 ANSI: 0 CCS
    sd 5:0:0:0: Attached scsi generic sg3 type 0
    usb-storage: device scan complete
    sd 5:0:0:0: [sdc] 7827456 512-byte hardware sectors: (4.00 GB/3.73 GiB)
    sd 5:0:0:0: [sdc] Write Protect is off
    sd 5:0:0:0: [sdc] Mode Sense: 23 00 00 00
    sd 5:0:0:0: [sdc] Assuming drive cache: write through
    sd 5:0:0:0: [sdc] Assuming drive cache: write through
    sdc:
    sd 5:0:0:0: [sdc] Attached SCSI removable disk
    forcedeth 0000:00:0a.0: irq 26 for MSI/MSI-X
    eth0: no link during initialization.
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    ADDRCONF(NETDEV_UP): eth0: link is not ready
    PM: Syncing filesystems ... done.
    Freezing user space processes ... (elapsed 0.00 seconds) done.
    Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
    Suspending console(s) (use no_console_suspend to debug)
    sd 3:0:0:0: [sda] Synchronizing SCSI cache
    sd 3:0:0:0: [sda] Stopping disk
    ath5k 0000:07:00.0: PCI INT A disabled
    forcedeth 0000:00:0a.0: wake-up capability disabled by ACPI
    forcedeth 0000:00:0a.0: PME# disabled
    forcedeth 0000:00:0a.0: PCI INT A disabled
    HDA Intel 0000:00:07.0: PCI INT A disabled
    ata2: port disabled. ignoring.
    ehci_hcd 0000:00:04.1: PCI INT B disabled
    ehci_hcd 0000:00:04.1: PME# disabled
    ohci_hcd 0000:00:04.0: PCI INT A disabled
    ohci_hcd 0000:00:04.0: PME# disabled
    ehci_hcd 0000:00:02.1: PCI INT B disabled
    ehci_hcd 0000:00:02.1: PME# disabled
    ohci_hcd 0000:00:02.0: PCI INT A disabled
    ohci_hcd 0000:00:02.0: PME# disabled
    ACPI: Preparing to enter system sleep state S3
    Disabling non-boot CPUs ...
    CPU 1 is now offline
    SMP alternatives: switching to UP code
    CPU0 attaching NULL sched-domain.
    CPU1 attaching NULL sched-domain.
    CPU0 attaching NULL sched-domain.
    CPU1 is down
    Extended CMOS year: 2000
    x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    Back to C!
    Extended CMOS year: 2000
    Enabling non-boot CPUs ...
    SMP alternatives: switching to SMP code
    Booting processor 1 APIC 0x1 ip 0x6000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 4001.76 BogoMIPS (lpj=6666816)
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 512K (64 bytes/line)
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
    CPU1: AMD Athlon Dual-Core QL-62 stepping 01
    CPU0 attaching NULL sched-domain.
    Switched to high resolution mode on CPU 1
    CPU0 attaching sched-domain:
    domain 0: span 0-1 level MC
    groups: 0 1
    CPU1 attaching sched-domain:
    domain 0: span 0-1 level MC
    groups: 1 0
    CPU1 is up
    ACPI: Waking up from system sleep state S3
    ohci_hcd 0000:00:02.0: restoring config space at offset 0x1 (was 0xb00007, writing 0xb00003)
    ehci_hcd 0000:00:02.1: restoring config space at offset 0x1 (was 0xb00006, writing 0xb00002)
    ohci_hcd 0000:00:04.0: restoring config space at offset 0x1 (was 0xb00007, writing 0xb00003)
    ehci_hcd 0000:00:04.1: restoring config space at offset 0x1 (was 0xb00006, writing 0xb00002)
    pata_amd 0000:00:06.0: restoring config space at offset 0x1 (was 0xb00005, writing 0xb80005)
    HDA Intel 0000:00:07.0: restoring config space at offset 0xf (was 0x5020100, writing 0x502010a)
    HDA Intel 0000:00:07.0: restoring config space at offset 0x4 (was 0x0, writing 0xc0000000)
    HDA Intel 0000:00:07.0: restoring config space at offset 0x1 (was 0xb00000, writing 0xb00002)
    ahci 0000:00:09.0: restoring config space at offset 0x1 (was 0xb00007, writing 0xb00407)
    pcieport-driver 0000:00:14.0: restoring config space at offset 0x7 (was 0x1f1, writing 0x200001f1)
    pcieport-driver 0000:00:14.0: restoring config space at offset 0x1 (was 0x100107, writing 0x1005
    nvidia 0000:02:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
    nvidia 0000:02:00.0: restoring config space at offset 0x9 (was 0x1, writing 0x4001)
    nvidia 0000:02:00.0: restoring config space at offset 0x7 (was 0xc, writing 0xc400000c)
    nvidia 0000:02:00.0: restoring config space at offset 0x5 (was 0xc, writing 0xd000000c)
    ath5k 0000:07:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
    nForce2_smbus 0000:00:01.1: PME# disabled
    ohci_hcd 0000:00:02.0: PME# disabled
    ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 17 (level, low) -> IRQ 17
    ohci_hcd 0000:00:02.0: setting latency timer to 64
    ohci_hcd 0000:00:02.0: PME# disabled
    ehci_hcd 0000:00:02.1: PME# disabled
    ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 17 (level, low) -> IRQ 17
    ehci_hcd 0000:00:02.1: setting latency timer to 64
    ehci_hcd 0000:00:02.1: PME# disabled
    usb usb1: root hub lost power or was reset
    ehci_hcd 0000:00:02.1: debug port 1
    ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
    ohci_hcd 0000:00:04.0: PME# disabled
    ohci_hcd 0000:00:04.0: PCI INT A -> Link[Z010] -> GSI 16 (level, low) -> IRQ 16
    ohci_hcd 0000:00:04.0: setting latency timer to 64
    ohci_hcd 0000:00:04.0: PME# disabled
    ehci_hcd 0000:00:04.1: PME# disabled
    ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z011] -> GSI 16 (level, low) -> IRQ 16
    ehci_hcd 0000:00:04.1: setting latency timer to 64
    ehci_hcd 0000:00:04.1: PME# disabled
    usb usb3: root hub lost power or was reset
    ehci_hcd 0000:00:04.1: debug port 1
    ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
    pata_amd 0000:00:06.0: restoring config space at offset 0x1 (was 0xb00005, writing 0xb80005)
    pata_amd 0000:00:06.0: setting latency timer to 64
    ata2: port disabled. ignoring.
    HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 19 (level, low) -> IRQ 19
    HDA Intel 0000:00:07.0: setting latency timer to 64
    pci 0000:00:08.0: setting latency timer to 64
    ahci 0000:00:09.0: setting latency timer to 64
    forcedeth 0000:00:0a.0: wake-up capability disabled by ACPI
    forcedeth 0000:00:0a.0: PME# disabled
    ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    forcedeth 0000:00:0a.0: irq 26 for MSI/MSI-X
    eth0: no link during initialization.
    pci 0000:00:0b.0: setting latency timer to 64
    ath5k 0000:07:00.0: PCI INT A -> Link[Z012] -> GSI 23 (level, low) -> IRQ 23
    sd 3:0:0:0: [sda] Starting disk
    ata4.00: qc timeout (cmd 0xec)
    ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata4.00: revalidation failed (errno=-5)
    ata3.00: qc timeout (cmd 0xa1)
    ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata3.00: revalidation failed (errno=-5)
    ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3.00: qc timeout (cmd 0xa1)
    ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata3.00: revalidation failed (errno=-5)
    ata3: limiting SATA link speed to 1.5 Gbps
    ata4.00: qc timeout (cmd 0xec)
    ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata4.00: revalidation failed (errno=-5)
    ata4: limiting SATA link speed to 1.5 Gbps
    ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    ata4: SATA link up <unknown> (SStatus 103 SControl 310)
    ata4.00: qc timeout (cmd 0xec)
    ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata4.00: revalidation failed (errno=-5)
    ata4.00: disabled
    ata3.00: qc timeout (cmd 0xa1)
    ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
    ata3.00: revalidation failed (errno=-5)
    ata3.00: disabled
    sd 3:0:0:0: [sda] START_STOP FAILED
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 134590273
    Buffer I/O error on device sda2, logical block 1094141
    lost page write due to I/O error on sda2
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 135807281
    Buffer I/O error on device sda2, logical block 1246267
    lost page write due to I/O error on sda2
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 135815833
    Buffer I/O error on device sda2, logical block 1247336
    lost page write due to I/O error on sda2
    JBD2: Detected IO errors while flushing file data on sda2:8
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 155463993
    Aborting journal on device sda2:8.
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 155459417
    Buffer I/O error on device sda2, logical block 3702784
    lost page write due to I/O error on sda2
    JBD2: I/O error detected when updating journal superblock for sda2:8.
    PM: Device 3:0:0:0 failed to resume: error 262144
    usb 1-1: reset high speed USB device using ehci_hcd and address 2
    usb 3-4: reset high speed USB device using ehci_hcd and address 2
    Restarting tasks ... <2>ext4_abort called.
    EXT4-fs error (device sda2): ext4_journal_start_sb: Detected aborted journal
    Remounting filesystem read-only
    ext4_da_writepages: jbd2_start: 1024 pages, ino 131086; err -30
    Pid: 20, comm: pdflush Tainted: P 2.6.30-ARCH #1
    Call Trace:
    [<ffffffffa00d738d>] ? ext4_da_writepages+0x47d/0x4b0 [ext4]
    [<ffffffff8026c6a4>] ? bit_waitqueue+0x24/0xe0
    [<ffffffff802c8332>] ? do_writepages+0x32/0x60
    [<ffffffff80321b7a>] ? __writeback_single_inode+0xba/0x490
    [<ffffffff802406e6>] ? dequeue_task_fair+0x56/0x1d0
    [<ffffffff8020a95c>] ? __switch_to+0xdc/0x3b0
    [<ffffffff803223b3>] ? generic_sync_sb_inodes+0x193/0x530
    [<ffffffff803229c5>] ? writeback_inodes+0x65/0x120
    [<ffffffff802c85a6>] ? wb_kupdate+0xc6/0x160
    [<ffffffff802c995b>] ? pdflush+0x16b/0x2a0
    [<ffffffff802c84e0>] ? wb_kupdate+0x0/0x160
    [<ffffffff802c97f0>] ? pdflush+0x0/0x2a0
    [<ffffffff802c97f0>] ? pdflush+0x0/0x2a0
    [<ffffffff8026c204>] ? kthread+0x64/0xc0
    [<ffffffff8024af20>] ? schedule_tail+0x30/0x80
    [<ffffffff8020d4fa>] ? child_rip+0xa/0x20
    [<ffffffff8026c1a0>] ? kthread+0x0/0xc0
    [<ffffffff8020d4f0>] ? child_rip+0x0/0x20
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 126637417
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 126637417
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 126637417
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 126637417
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 126637417
    done.
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 130097993
    EXT4-fs error (device sda2): ext4_find_entry: reading directory #139292 offset 0
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 126637417
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 126004889
    EXT4-fs error (device sda2): ext4_find_entry: reading directory #98457 offset 0
    sd 3:0:0:0: [sda] Unhandled error code
    sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
    end_request: I/O error, dev sda, sector 126004889
    EXT4-fs error (device sda2): ext4_find_entry: reading directory #98457 offset 0
    ANY help would be much appreciated.
    Last edited by Cappy (2009-08-10 08:19:09)

    Nevermind .. *sigh* ... pci=msi on the kernel fixed it .. going to go cut myself now ...

  • My external hard drive is in Read Only mode...

    My external hard drive, which I have used before, is in "Read Only Mode."
    I have put files on this drive and taken files off of it before, so it isn't an NTFS issue.
    I am still able to write with a different Mac.
    FYI, this is a Late-2011 Macbook Air.

    You are about to format your storage device. Be sure to copy and take the back up before formatting. Just select the physical disc you want to reformat in the tree on the left-hand side of Disk Utility. You can select a new file system format from the drop down below, and also name the new volume to be created. Showing the info of the newly formatted drive, you can see the disc is now set to read and write.

  • Read only file system

    One of my Parabola installations has started to always mount the / partition read-only. I've booted into a different install on the same machine, and can mount the affected partition without problems. I've done a fsck, and run the SMART disk checks. No problems. I've touched /forcefsck so a file system check is done every time I boot, but still the partition is read-only when it finishes booting.
    This is the output of 'mount':
    proc on /proc type proc (rw,nosuid,nodev,noexec,relatime)
    sys on /sys type sysfs (rw,nosuid,nodev,noexec,relatime)
    dev on /dev type devtmpfs (rw,nosuid,relatime,size=1024388k,nr_inodes=256097,mode=755)
    run on /run type tmpfs (rw,nosuid,nodev,relatime,mode=755)
    /dev/sdb10 on / type ext4 (ro,relatime,data=ordered)
    tmpfs on /tmp type tmpfs (rw,nosuid,nodev,relatime)
    /dev/sdb9 on /boot type ext4 (rw,relatime,data=ordered)
    /dev/sdb1 on /media/Stuff type fuseblk (rw,nosuid,nodev,noexec,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096)
    binfmt on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,relatime)
    This is the output of 'dmesg':
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Linux version 3.6.3-1-LIBRE (nobody@root) (gcc version 4.7.2 (GCC) ) #1 SMP PREEMPT Tue Oct 23 00:29:01 UYST 2012
    [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux-libre root=UUID=f0206707-f1ca-4bea-9eb3-c5d3713e4a4e ro resume=UUID=5b4248ba-30c3-48e5-a090-3a9c9f49d9c4 quiet
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007ff8ffff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000007ff90000-0x000000007ff9dfff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x000000007ff9e000-0x000000007ffcffff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x000000007ffd0000-0x000000007ffddfff] reserved
    [ 0.000000] BIOS-e820: [mem 0x000000007ffe0000-0x000000007fffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] DMI present.
    [ 0.000000] DMI: System manufacturer System Product Name/P5KPL-CM, BIOS 0702 08/27/2010
    [ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x7ff90 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-DFFFF write-protect
    [ 0.000000] E0000-EFFFF write-through
    [ 0.000000] F0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask F80000000 write-back
    [ 0.000000] 1 disabled
    [ 0.000000] 2 disabled
    [ 0.000000] 3 disabled
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [ffff8800000ff780]
    [ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
    [ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x7ff8ffff]
    [ 0.000000] [mem 0x00000000-0x7fdfffff] page 2M
    [ 0.000000] [mem 0x7fe00000-0x7ff8ffff] page 4k
    [ 0.000000] kernel direct mapping tables up to 0x7ff8ffff @ [mem 0x1fbfd000-0x1fffffff]
    [ 0.000000] RAMDISK: [mem 0x37a10000-0x37cfffff]
    [ 0.000000] ACPI: RSDP 00000000000fb6a0 00014 (v00 ACPIAM)
    [ 0.000000] ACPI: RSDT 000000007ff90000 0003C (v01 A_M_I_ OEMRSDT 08001027 MSFT 00000097)
    [ 0.000000] ACPI: FACP 000000007ff90200 00084 (v02 A_M_I_ OEMFACP 08001027 MSFT 00000097)
    [ 0.000000] ACPI: DSDT 000000007ff905c0 07BFA (v01 A0968 A0968000 00000000 INTL 20060113)
    [ 0.000000] ACPI: FACS 000000007ff9e000 00040
    [ 0.000000] ACPI: APIC 000000007ff90390 0006C (v01 A_M_I_ OEMAPIC 08001027 MSFT 00000097)
    [ 0.000000] ACPI: MCFG 000000007ff90400 0003C (v01 A_M_I_ OEMMCFG 08001027 MSFT 00000097)
    [ 0.000000] ACPI: OEMB 000000007ff9e040 00080 (v01 A_M_I_ AMI_OEM 08001027 MSFT 00000097)
    [ 0.000000] ACPI: HPET 000000007ff981c0 00038 (v01 A_M_I_ OEMHPET 08001027 MSFT 00000097)
    [ 0.000000] ACPI: GSCI 000000007ff9e0c0 02024 (v01 A_M_I_ GMCHSCI 08001027 MSFT 00000097)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000007ff8ffff]
    [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x7ff8ffff]
    [ 0.000000] NODE_DATA [mem 0x7ff8c000-0x7ff8ffff]
    [ 0.000000] [ffffea0000000000-ffffea0001ffffff] PMD -> [ffff88007d600000-ffff88007f5fffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00010000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal empty
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00010000-0x0009efff]
    [ 0.000000] node 0: [mem 0x00100000-0x7ff8ffff]
    [ 0.000000] On node 0 totalpages: 524063
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 6 pages reserved
    [ 0.000000] DMA zone: 3913 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 8127 pages used for memmap
    [ 0.000000] DMA32 zone: 511953 pages, LIFO batch:31
    [ 0.000000] ACPI: PM-Timer IO Port: 0x808
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
    [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
    [ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
    [ 0.000000] e820: [mem 0x80000000-0xfedfffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88007fc00000 s84608 r8192 d21888 u524288
    [ 0.000000] pcpu-alloc: s84608 r8192 d21888 u524288 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 515866
    [ 0.000000] Policy zone: DMA32
    [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux-libre root=UUID=f0206707-f1ca-4bea-9eb3-c5d3713e4a4e ro resume=UUID=5b4248ba-30c3-48e5-a090-3a9c9f49d9c4 quiet
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] __ex_table already sorted, skipping sort
    [ 0.000000] Checking aperture...
    [ 0.000000] No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 2048780k/2096704k available (4726k kernel code, 452k absent, 47472k reserved, 4144k data, 772k init)
    [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
    [ 0.000000] NR_IRQS:4352 nr_irqs:712 16
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 8388608 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration using PIT
    [ 0.000000] tsc: Detected 1613.131 MHz processor
    [ 0.003338] Calibrating delay loop (skipped), value calculated using timer frequency.. 3227.68 BogoMIPS (lpj=5377103)
    [ 0.003342] pid_max: default: 32768 minimum: 301
    [ 0.003391] Security Framework initialized
    [ 0.003397] AppArmor: AppArmor disabled by boot time parameter
    [ 0.003643] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.004961] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.005580] Mount-cache hash table entries: 256
    [ 0.005927] Initializing cgroup subsys cpuacct
    [ 0.005933] Initializing cgroup subsys memory
    [ 0.005946] Initializing cgroup subsys devices
    [ 0.005949] Initializing cgroup subsys freezer
    [ 0.005951] Initializing cgroup subsys net_cls
    [ 0.005953] Initializing cgroup subsys blkio
    [ 0.005995] CPU: Physical Processor ID: 0
    [ 0.005998] CPU: Processor Core ID: 0
    [ 0.006000] mce: CPU supports 6 MCE banks
    [ 0.006010] CPU0: Thermal monitoring enabled (TM2)
    [ 0.006015] process: using mwait in idle threads
    [ 0.006021] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
    Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32
    tlb_flushall_shift is 0xffffffff
    [ 0.008169] ACPI: Core revision 20120711
    [ 0.013350] ftrace: allocating 18348 entries in 72 pages
    [ 0.026962] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.059974] smpboot: CPU0: Intel(R) Celeron(R) CPU E1200 @ 1.60GHz stepping 0d
    [ 0.059996] Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
    [ 0.059996] perf_event_intel: PEBS disabled due to CPU errata
    [ 0.059996] ... version: 2
    [ 0.059996] ... bit width: 40
    [ 0.059996] ... generic registers: 2
    [ 0.059996] ... value mask: 000000ffffffffff
    [ 0.059996] ... max period: 000000007fffffff
    [ 0.059996] ... fixed-purpose events: 3
    [ 0.059996] ... event mask: 0000000700000003
    [ 0.083501] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.096681] smpboot: Booting Node 0, Processors #1
    [ 0.109825] Brought up 2 CPUs
    [ 0.109825] smpboot: Total of 2 processors activated (6455.37 BogoMIPS)
    [ 0.110104] devtmpfs: initialized
    [ 0.112186] PM: Registering ACPI NVS region [mem 0x7ff9e000-0x7ffcffff] (204800 bytes)
    [ 0.112186] NET: Registered protocol family 16
    [ 0.112186] ACPI: bus type pci registered
    [ 0.112186] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
    [ 0.112186] PCI: not using MMCONFIG
    [ 0.112186] PCI: Using configuration type 1 for base access
    [ 0.113367] bio: create slab <bio-0> at 0
    [ 0.113401] ACPI: Added _OSI(Module Device)
    [ 0.113401] ACPI: Added _OSI(Processor Device)
    [ 0.113401] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.113401] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.114233] ACPI: EC: Look up EC in DSDT
    [ 0.116040] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.122816] ACPI: SSDT 000000007ffa00f0 001D2 (v01 AMI CPU1PM 00000001 INTL 20060113)
    [ 0.122816] ACPI: Dynamic OEM Table Load:
    [ 0.122816] ACPI: SSDT (null) 001D2 (v01 AMI CPU1PM 00000001 INTL 20060113)
    [ 0.122816] ACPI: SSDT 000000007ffa02d0 00143 (v01 AMI CPU2PM 00000001 INTL 20060113)
    [ 0.122816] ACPI: Dynamic OEM Table Load:
    [ 0.122816] ACPI: SSDT (null) 00143 (v01 AMI CPU2PM 00000001 INTL 20060113)
    [ 0.122816] ACPI: Interpreter enabled
    [ 0.122816] ACPI: (supports S0 S1 S3 S4 S5)
    [ 0.122816] ACPI: Using IOAPIC for interrupt routing
    [ 0.122816] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
    [ 0.122816] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in ACPI motherboard resources
    [ 0.136077] ACPI: No dock devices found.
    [ 0.136086] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.136182] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.136328] pci_root PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
    [ 0.136382] PCI host bridge to bus 0000:00
    [ 0.136387] pci_bus 0000:00: busn_res: [bus 00-ff] is inserted under domain [bus 00-ff]
    [ 0.136390] pci_bus 0000:00: root bus resource [bus 00-ff]
    [ 0.136394] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.136397] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.136400] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.136403] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff]
    [ 0.136406] pci_bus 0000:00: root bus resource [mem 0x80000000-0xffffffff]
    [ 0.136420] pci 0000:00:00.0: [8086:29c0] type 00 class 0x060000
    [ 0.136478] pci 0000:00:01.0: [8086:29c1] type 01 class 0x060400
    [ 0.136533] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    [ 0.136587] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
    [ 0.136606] pci 0000:00:1b.0: reg 10: [mem 0xfe9fc000-0xfe9fffff 64bit]
    [ 0.136697] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.136723] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
    [ 0.136803] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.136831] pci 0000:00:1c.1: [8086:27d2] type 01 class 0x060400
    [ 0.136910] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    [ 0.136941] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
    [ 0.136986] pci 0000:00:1d.0: reg 20: [io 0xc480-0xc49f]
    [ 0.137022] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
    [ 0.137067] pci 0000:00:1d.1: reg 20: [io 0xc800-0xc81f]
    [ 0.137108] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
    [ 0.137153] pci 0000:00:1d.2: reg 20: [io 0xc880-0xc89f]
    [ 0.137190] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
    [ 0.137235] pci 0000:00:1d.3: reg 20: [io 0xcc00-0xcc1f]
    [ 0.137282] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
    [ 0.137304] pci 0000:00:1d.7: reg 10: [mem 0xfe9fbc00-0xfe9fbfff]
    [ 0.137395] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.137419] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
    [ 0.137491] pci 0000:00:1f.0: [8086:27b8] type 00 class 0x060100
    [ 0.137581] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
    [ 0.137630] pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018a
    [ 0.137645] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
    [ 0.137656] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
    [ 0.137667] pci 0000:00:1f.1: reg 18: [io 0x08f0-0x08f7]
    [ 0.137678] pci 0000:00:1f.1: reg 1c: [io 0x08f8-0x08fb]
    [ 0.137689] pci 0000:00:1f.1: reg 20: [io 0xffa0-0xffaf]
    [ 0.137730] pci 0000:00:1f.2: [8086:27c0] type 00 class 0x01018f
    [ 0.137747] pci 0000:00:1f.2: reg 10: [io 0xc400-0xc407]
    [ 0.137757] pci 0000:00:1f.2: reg 14: [io 0xc080-0xc083]
    [ 0.137767] pci 0000:00:1f.2: reg 18: [io 0xc000-0xc007]
    [ 0.137777] pci 0000:00:1f.2: reg 1c: [io 0xbc00-0xbc03]
    [ 0.137786] pci 0000:00:1f.2: reg 20: [io 0xb880-0xb88f]
    [ 0.137827] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.137845] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
    [ 0.137901] pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]
    [ 0.137974] pci_bus 0000:01: busn_res: [bus 01] is inserted under [bus 00-ff]
    [ 0.137991] pci 0000:01:00.0: [1002:68f9] type 00 class 0x030000
    [ 0.138008] pci 0000:01:00.0: reg 10: [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.138021] pci 0000:01:00.0: reg 18: [mem 0xfeac0000-0xfeadffff 64bit]
    [ 0.138031] pci 0000:01:00.0: reg 20: [io 0xd000-0xd0ff]
    [ 0.138047] pci 0000:01:00.0: reg 30: [mem 0xfeaa0000-0xfeabffff pref]
    [ 0.138085] pci 0000:01:00.0: supports D1 D2
    [ 0.138109] pci 0000:01:00.1: [1002:aa68] type 00 class 0x040300
    [ 0.138125] pci 0000:01:00.1: reg 10: [mem 0xfeafc000-0xfeafffff 64bit]
    [ 0.138195] pci 0000:01:00.1: supports D1 D2
    [ 0.138231] pci 0000:00:01.0: PCI bridge to [bus 01]
    [ 0.138236] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
    [ 0.138240] pci 0000:00:01.0: bridge window [mem 0xfea00000-0xfeafffff]
    [ 0.138246] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.138291] pci_bus 0000:03: busn_res: [bus 03] is inserted under [bus 00-ff]
    [ 0.138295] pci 0000:00:1c.0: PCI bridge to [bus 03]
    [ 0.138347] pci_bus 0000:02: busn_res: [bus 02] is inserted under [bus 00-ff]
    [ 0.138372] pci 0000:02:00.0: [1969:1026] type 00 class 0x020000
    [ 0.138398] pci 0000:02:00.0: reg 10: [mem 0xfebc0000-0xfebfffff 64bit]
    [ 0.138412] pci 0000:02:00.0: reg 18: [io 0xec00-0xec7f]
    [ 0.138519] pci 0000:02:00.0: PME# supported from D3hot D3cold
    [ 0.138544] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    [ 0.138555] pci 0000:00:1c.1: PCI bridge to [bus 02]
    [ 0.138560] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
    [ 0.138565] pci 0000:00:1c.1: bridge window [mem 0xfeb00000-0xfebfffff]
    [ 0.138595] pci_bus 0000:04: busn_res: [bus 04] is inserted under [bus 00-ff]
    [ 0.138642] pci 0000:00:1e.0: PCI bridge to [bus 04] (subtractive decode)
    [ 0.138654] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.138657] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.138660] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.138663] pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
    [ 0.138666] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xffffffff] (subtractive decode)
    [ 0.138689] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [ 0.138794] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
    [ 0.138867] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
    [ 0.138903] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
    [ 0.138963] pci0000:00: ACPI _OSC support notification failed, disabling PCIe ASPM
    [ 0.138967] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x08)
    [ 0.145009] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *11 12 14 15)
    [ 0.145073] ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
    [ 0.145128] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 11 12 14 15)
    [ 0.145187] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *11 12 14 15)
    [ 0.145246] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 11 12 14 15) *0, disabled.
    [ 0.145306] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 11 12 14 15) *0, disabled.
    [ 0.145365] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 11 12 14 15) *0, disabled.
    [ 0.145425] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 11 12 14 15)
    [ 0.146698] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.146703] vgaarb: loaded
    [ 0.146705] vgaarb: bridge control possible 0000:01:00.0
    [ 0.146775] PCI: Using ACPI for IRQ routing
    [ 0.147301] PCI: pci_cache_line_size set to 64 bytes
    [ 0.147387] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
    [ 0.147389] e820: reserve RAM buffer [mem 0x7ff90000-0x7fffffff]
    [ 0.147545] NetLabel: Initializing
    [ 0.147548] NetLabel: domain hash size = 128
    [ 0.147550] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.147571] NetLabel: unlabeled traffic allowed by default
    [ 0.147588] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    [ 0.147593] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [ 0.147599] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    [ 0.166686] Switching to clocksource hpet
    [ 0.177018] pnp: PnP ACPI init
    [ 0.177044] ACPI: bus type pnp registered
    [ 0.177174] pnp 00:00: [bus 00-ff]
    [ 0.177179] pnp 00:00: [io 0x0cf8-0x0cff]
    [ 0.177182] pnp 00:00: [io 0x0000-0x0cf7 window]
    [ 0.177186] pnp 00:00: [io 0x0d00-0xffff window]
    [ 0.177189] pnp 00:00: [mem 0x000a0000-0x000bffff window]
    [ 0.177192] pnp 00:00: [mem 0x000d0000-0x000dffff window]
    [ 0.177195] pnp 00:00: [mem 0x80000000-0xffffffff window]
    [ 0.177279] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
    [ 0.177295] pnp 00:01: [mem 0xfed14000-0xfed19fff]
    [ 0.177363] system 00:01: [mem 0xfed14000-0xfed19fff] has been reserved
    [ 0.177369] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.177419] pnp 00:02: [dma 4]
    [ 0.177423] pnp 00:02: [io 0x0000-0x000f]
    [ 0.177426] pnp 00:02: [io 0x0081-0x0083]
    [ 0.177429] pnp 00:02: [io 0x0087]
    [ 0.177431] pnp 00:02: [io 0x0089-0x008b]
    [ 0.177434] pnp 00:02: [io 0x008f]
    [ 0.177437] pnp 00:02: [io 0x00c0-0x00df]
    [ 0.177478] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.177494] pnp 00:03: [io 0x0070-0x0071]
    [ 0.177508] pnp 00:03: [irq 8]
    [ 0.177544] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.177557] pnp 00:04: [io 0x0061]
    [ 0.177595] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
    [ 0.177609] pnp 00:05: [io 0x00f0-0x00ff]
    [ 0.177617] pnp 00:05: [irq 13]
    [ 0.177654] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.178000] pnp 00:06: [irq 6]
    [ 0.178004] pnp 00:06: [dma 2]
    [ 0.178007] pnp 00:06: [io 0x03f0-0x03f5]
    [ 0.178010] pnp 00:06: [io 0x03f7]
    [ 0.178096] pnp 00:06: Plug and Play ACPI device, IDs PNP0700 (active)
    [ 0.178501] pnp 00:07: [irq 7]
    [ 0.178504] pnp 00:07: [dma 3]
    [ 0.178508] pnp 00:07: [io 0x0378-0x037f]
    [ 0.178511] pnp 00:07: [io 0x0778-0x077f]
    [ 0.178686] pnp 00:07: Plug and Play ACPI device, IDs PNP0401 (active)
    [ 0.178731] pnp 00:08: [io 0x0000-0xffffffffffffffff disabled]
    [ 0.178735] pnp 00:08: [io 0x0000-0xffffffffffffffff disabled]
    [ 0.178738] pnp 00:08: [io 0x0290-0x0297]
    [ 0.178815] system 00:08: [io 0x0290-0x0297] has been reserved
    [ 0.178821] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.178918] pnp 00:09: [io 0x0010-0x001f]
    [ 0.178922] pnp 00:09: [io 0x0022-0x003f]
    [ 0.178925] pnp 00:09: [io 0x0044-0x005f]
    [ 0.178928] pnp 00:09: [io 0x0062-0x0063]
    [ 0.178934] pnp 00:09: [io 0x0065-0x006f]
    [ 0.178937] pnp 00:09: [io 0x0072-0x007f]
    [ 0.178939] pnp 00:09: [io 0x0080]
    [ 0.178942] pnp 00:09: [io 0x0084-0x0086]
    [ 0.178945] pnp 00:09: [io 0x0088]
    [ 0.178948] pnp 00:09: [io 0x008c-0x008e]
    [ 0.178951] pnp 00:09: [io 0x0090-0x009f]
    [ 0.178953] pnp 00:09: [io 0x00a2-0x00bf]
    [ 0.178956] pnp 00:09: [io 0x00e0-0x00ef]
    [ 0.178959] pnp 00:09: [io 0x04d0-0x04d1]
    [ 0.178962] pnp 00:09: [io 0x0800-0x087f]
    [ 0.178965] pnp 00:09: [io 0x0000-0xffffffffffffffff disabled]
    [ 0.178968] pnp 00:09: [io 0x0480-0x04bf]
    [ 0.178971] pnp 00:09: [mem 0xfed1c000-0xfed1ffff]
    [ 0.178974] pnp 00:09: [mem 0xfed20000-0xfed8ffff]
    [ 0.179068] system 00:09: [io 0x04d0-0x04d1] has been reserved
    [ 0.179072] system 00:09: [io 0x0800-0x087f] has been reserved
    [ 0.179076] system 00:09: [io 0x0480-0x04bf] has been reserved
    [ 0.179080] system 00:09: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.179083] system 00:09: [mem 0xfed20000-0xfed8ffff] has been reserved
    [ 0.179089] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.179173] pnp 00:0a: [mem 0xfed00000-0xfed003ff]
    [ 0.179219] pnp 00:0a: Plug and Play ACPI device, IDs PNP0103 (active)
    [ 0.179280] pnp 00:0b: [mem 0xffb00000-0xffbfffff]
    [ 0.179284] pnp 00:0b: [mem 0xfff00000-0xffffffff]
    [ 0.179332] pnp 00:0b: Plug and Play ACPI device, IDs INT0800 (active)
    [ 0.179387] pnp 00:0c: [mem 0xffc00000-0xffefffff]
    [ 0.179460] system 00:0c: [mem 0xffc00000-0xffefffff] has been reserved
    [ 0.179466] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.179524] pnp 00:0d: [mem 0xfec00000-0xfec00fff]
    [ 0.179528] pnp 00:0d: [mem 0xfee00000-0xfee00fff]
    [ 0.179608] system 00:0d: [mem 0xfec00000-0xfec00fff] could not be reserved
    [ 0.179612] system 00:0d: [mem 0xfee00000-0xfee00fff] has been reserved
    [ 0.179617] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.179660] pnp 00:0e: [io 0x0060]
    [ 0.179663] pnp 00:0e: [io 0x0064]
    [ 0.179673] pnp 00:0e: [irq 1]
    [ 0.179734] pnp 00:0e: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
    [ 0.179796] pnp 00:0f: [irq 12]
    [ 0.179852] pnp 00:0f: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
    [ 0.180166] pnp 00:10: [irq 4]
    [ 0.180170] pnp 00:10: [dma 0 disabled]
    [ 0.180173] pnp 00:10: [io 0x03f8-0x03ff]
    [ 0.180292] pnp 00:10: Plug and Play ACPI device, IDs PNP0501 (active)
    [ 0.180342] pnp 00:11: [mem 0xf0000000-0xf3ffffff]
    [ 0.180427] system 00:11: [mem 0xf0000000-0xf3ffffff] has been reserved
    [ 0.180433] system 00:11: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.180636] pnp 00:12: [mem 0x00000000-0x0009ffff]
    [ 0.180640] pnp 00:12: [mem 0x000c0000-0x000cffff]
    [ 0.180643] pnp 00:12: [mem 0x000e0000-0x000fffff]
    [ 0.180646] pnp 00:12: [mem 0x00100000-0x7fffffff]
    [ 0.180649] pnp 00:12: [mem 0x00000000-0xffffffffffffffff disabled]
    [ 0.180743] system 00:12: [mem 0x00000000-0x0009ffff] could not be reserved
    [ 0.180747] system 00:12: [mem 0x000c0000-0x000cffff] could not be reserved
    [ 0.180751] system 00:12: [mem 0x000e0000-0x000fffff] could not be reserved
    [ 0.180754] system 00:12: [mem 0x00100000-0x7fffffff] could not be reserved
    [ 0.180760] system 00:12: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.180916] pnp: PnP ACPI: found 19 devices
    [ 0.180919] ACPI: ACPI bus type pnp unregistered
    [ 0.188605] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 03] add_size 1000
    [ 0.188613] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000
    [ 0.188617] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 03] add_size 200000
    [ 0.188628] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
    [ 0.188646] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
    [ 0.188650] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
    [ 0.188653] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
    [ 0.188657] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
    [ 0.188664] pci 0000:00:1c.0: BAR 14: assigned [mem 0x80000000-0x801fffff]
    [ 0.188668] pci 0000:00:1c.0: BAR 15: assigned [mem 0x80200000-0x803fffff 64bit pref]
    [ 0.188673] pci 0000:00:1c.1: BAR 15: assigned [mem 0x80400000-0x805fffff 64bit pref]
    [ 0.188678] pci 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
    [ 0.188683] pci 0000:00:01.0: PCI bridge to [bus 01]
    [ 0.188687] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
    [ 0.188693] pci 0000:00:01.0: bridge window [mem 0xfea00000-0xfeafffff]
    [ 0.188697] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.188703] pci 0000:00:1c.0: PCI bridge to [bus 03]
    [ 0.188707] pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
    [ 0.188713] pci 0000:00:1c.0: bridge window [mem 0x80000000-0x801fffff]
    [ 0.188718] pci 0000:00:1c.0: bridge window [mem 0x80200000-0x803fffff 64bit pref]
    [ 0.188725] pci 0000:00:1c.1: PCI bridge to [bus 02]
    [ 0.188729] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
    [ 0.188735] pci 0000:00:1c.1: bridge window [mem 0xfeb00000-0xfebfffff]
    [ 0.188740] pci 0000:00:1c.1: bridge window [mem 0x80400000-0x805fffff 64bit pref]
    [ 0.188747] pci 0000:00:1e.0: PCI bridge to [bus 04]
    [ 0.188784] pci 0000:00:1c.0: enabling device (0104 -> 0107)
    [ 0.188805] pci 0000:00:1e.0: setting latency timer to 64
    [ 0.188810] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.188814] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.188817] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.188820] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
    [ 0.188824] pci_bus 0000:00: resource 8 [mem 0x80000000-0xffffffff]
    [ 0.188827] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
    [ 0.188830] pci_bus 0000:01: resource 1 [mem 0xfea00000-0xfeafffff]
    [ 0.188833] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.188836] pci_bus 0000:03: resource 0 [io 0x1000-0x1fff]
    [ 0.188840] pci_bus 0000:03: resource 1 [mem 0x80000000-0x801fffff]
    [ 0.188843] pci_bus 0000:03: resource 2 [mem 0x80200000-0x803fffff 64bit pref]
    [ 0.188846] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
    [ 0.188849] pci_bus 0000:02: resource 1 [mem 0xfeb00000-0xfebfffff]
    [ 0.188852] pci_bus 0000:02: resource 2 [mem 0x80400000-0x805fffff 64bit pref]
    [ 0.188856] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
    [ 0.188859] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
    [ 0.188862] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.188865] pci_bus 0000:04: resource 7 [mem 0x000d0000-0x000dffff]
    [ 0.188868] pci_bus 0000:04: resource 8 [mem 0x80000000-0xffffffff]
    [ 0.188916] NET: Registered protocol family 2
    [ 0.189551] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
    [ 0.192082] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    [ 0.192686] TCP: Hash tables configured (established 262144 bind 65536)
    [ 0.192758] TCP: reno registered
    [ 0.192773] UDP hash table entries: 1024 (order: 3, 32768 bytes)
    [ 0.192798] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
    [ 0.192949] NET: Registered protocol family 1
    [ 0.193147] pci 0000:01:00.0: Boot video device
    [ 0.193158] PCI: CLS 32 bytes, default 64
    [ 0.193230] Unpacking initramfs...
    [ 0.285578] Freeing initrd memory: 3008k freed
    [ 0.287514] audit: initializing netlink socket (disabled)
    [ 0.287533] type=2000 audit(1351450895.286:1): initialized
    [ 0.303689] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.306261] VFS: Disk quotas dquot_6.5.2
    [ 0.306342] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.306570] msgmni has been set to 4007
    [ 0.306904] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.306951] io scheduler noop registered
    [ 0.306955] io scheduler deadline registered
    [ 0.307043] io scheduler cfq registered (default)
    [ 0.307215] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
    [ 0.307324] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
    [ 0.307443] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
    [ 0.307659] intel_idle: does not run on family 6 model 15
    [ 0.307698] GHES: HEST is not enabled!
    [ 0.307788] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.328340] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.349279] 00:10: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.349579] Linux agpgart interface v0.103
    [ 0.349708] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
    [ 0.352389] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.352444] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.352607] mousedev: PS/2 mouse device common for all mice
    [ 0.352700] rtc_cmos 00:03: RTC can wake from S4
    [ 0.352865] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
    [ 0.352896] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
    [ 0.352913] cpuidle: using governor ladder
    [ 0.352915] cpuidle: using governor menu
    [ 0.353088] drop_monitor: Initializing network drop monitor service
    [ 0.353195] TCP: cubic registered
    [ 0.353379] NET: Registered protocol family 10
    [ 0.353609] NET: Registered protocol family 17
    [ 0.353626] Key type dns_resolver registered
    [ 0.353965] PM: Checking hibernation image partition UUID=5b4248ba-30c3-48e5-a090-3a9c9f49d9c4
    [ 0.377050] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 0.398600] PM: Hibernation image not present or could not be loaded.
    [ 0.398629] registered taskstats version 1
    [ 0.399166] rtc_cmos 00:03: setting system clock to 2012-10-28 19:01:35 UTC (1351450895)
    [ 0.400807] Freeing unused kernel memory: 772k freed
    [ 0.401093] Write protecting the kernel read-only data: 8192k
    [ 0.407007] Freeing unused kernel memory: 1408k freed
    [ 0.410355] Freeing unused kernel memory: 652k freed
    [ 0.424642] systemd-udevd[42]: starting version 194
    [ 0.484567] ACPI: bus type usb registered
    [ 0.484613] usbcore: registered new interface driver usbfs
    [ 0.484629] usbcore: registered new interface driver hub
    [ 0.484994] usbcore: registered new device driver usb
    [ 0.485924] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.485981] ehci_hcd 0000:00:1d.7: setting latency timer to 64
    [ 0.485987] ehci_hcd 0000:00:1d.7: EHCI Host Controller
    [ 0.485997] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    [ 0.489913] ehci_hcd 0000:00:1d.7: debug port 1
    [ 0.489922] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
    [ 0.489951] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe9fbc00
    [ 0.493550] SCSI subsystem initialized
    [ 0.496118] ACPI: bus type scsi registered
    [ 0.496720] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    [ 0.497003] hub 1-0:1.0: USB hub found
    [ 0.497013] hub 1-0:1.0: 8 ports detected
    [ 0.497923] uhci_hcd: USB Universal Host Controller Interface driver
    [ 0.497967] uhci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 0.497972] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [ 0.497982] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    [ 0.498020] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000c480
    [ 0.498143] libata version 3.00 loaded.
    [ 0.499305] hub 2-0:1.0: USB hub found
    [ 0.499317] hub 2-0:1.0: 2 ports detected
    [ 0.499540] uhci_hcd 0000:00:1d.1: setting latency timer to 64
    [ 0.499547] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [ 0.499557] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    [ 0.499610] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c800
    [ 0.500253] hub 3-0:1.0: USB hub found
    [ 0.500264] hub 3-0:1.0: 2 ports detected
    [ 0.500442] uhci_hcd 0000:00:1d.2: setting latency timer to 64
    [ 0.500448] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [ 0.500463] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    [ 0.500512] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000c880
    [ 0.500811] hub 4-0:1.0: USB hub found
    [ 0.500822] hub 4-0:1.0: 2 ports detected
    [ 0.501016] uhci_hcd 0000:00:1d.3: setting latency timer to 64
    [ 0.501022] uhci_hcd 0000:00:1d.3: UHCI Host Controller
    [ 0.501039] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    [ 0.501090] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000cc00
    [ 0.502169] hub 5-0:1.0: USB hub found
    [ 0.502179] hub 5-0:1.0: 2 ports detected
    [ 0.502422] ata_piix 0000:00:1f.1: version 2.13
    [ 0.502499] ata_piix 0000:00:1f.1: setting latency timer to 64
    [ 0.503963] scsi0 : ata_piix
    [ 0.504744] scsi1 : ata_piix
    [ 0.505372] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
    [ 0.505378] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
    [ 0.505429] ata_piix 0000:00:1f.2: MAP [
    [ 0.505431] P0 P2 P1 P3 ]
    [ 0.505484] ata_piix 0000:00:1f.2: setting latency timer to 64
    [ 0.507566] scsi2 : ata_piix
    [ 0.508975] scsi3 : ata_piix
    [ 0.509624] ata3: SATA max UDMA/133 cmd 0xc400 ctl 0xc080 bmdma 0xb880 irq 19
    [ 0.509630] ata4: SATA max UDMA/133 cmd 0xc000 ctl 0xbc00 bmdma 0xb888 irq 19
    [ 0.684177] ata3.00: ATA-8: WDC WD6400AAKS-00A7B2, 01.03B01, max UDMA/133
    [ 0.684184] ata3.00: 1250263728 sectors, multi 16: LBA48 NCQ (depth 0/32)
    [ 0.691230] ata3.00: configured for UDMA/133
    [ 0.691417] scsi 2:0:0:0: Direct-Access ATA WDC WD6400AAKS-0 01.0 PQ: 0 ANSI: 5
    [ 0.699349] sd 2:0:0:0: [sda] 1250263728 512-byte logical blocks: (640 GB/596 GiB)
    [ 0.699463] sd 2:0:0:0: [sda] Write Protect is off
    [ 0.699468] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 0.699516] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 0.774080] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
    [ 0.775132] sd 2:0:0:0: [sda] Attached SCSI disk
    [ 1.096765] usb 2-2: new low-speed USB device number 2 using uhci_hcd
    [ 1.275214] usbcore: registered new interface driver usbhid
    [ 1.275219] usbhid: USB HID core driver
    [ 1.276959] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input1
    [ 1.277358] hid-generic 0003:04B3:310C.0001: input,hidraw0: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:1d.0-2/input0
    [ 1.290145] tsc: Refined TSC clocksource calibration: 1613.217 MHz
    [ 1.290153] Switching to clocksource tsc
    [ 1.426263] PM: Starting manual resume from disk
    [ 1.426269] PM: Hibernation image partition 8:8 present
    [ 1.426271] PM: Looking for hibernation image.
    [ 1.426530] PM: Image not found (code -22)
    [ 1.426535] PM: Hibernation image not present or could not be loaded.
    [ 1.648559] EXT4-fs (sda10): mounted filesystem with ordered data mode. Opts: (null)
    [ 12.388263] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
    [ 12.459036] fuse init (API version 7.20)
    [ 13.150864] Adding 1951860k swap on /dev/sda8. Priority:-1 extents:1 across:1951860k
    [ 0.691798] ACPI: Invalid Power Resource to register!
    [ 14.060519] synergys[417]: segfault at 0 ip 0000000000449fa9 sp 00007fff68a19a90 error 4
    [ 14.060531] in synergys[400000+cb000]
    (I disconnected the second hard drive in the machine to verify that it wasn't causing problems. Hence the sda / sdb discrepancy)
    I've been able to mount the partitions and chroot into them, but I don't know what to do from here. Oddly, I've discovered that 'ls' doesn't output anything, although bash completion seems to work ok.
    Any ideas on what I should do to get my system running again?
    Thanks in advance,
    Bernie

    Have you read the forum rules? Asking for support for Parabola isn't going to get you very far.
    https://wiki.archlinux.org/index.php/Fo … pport_ONLY

  • Correcting 'Read only' file problem ...

    I while ago I had an HD problem. I installed a new HD, upgraded to Leopard and then brought all my old files in from an external backup.
    My problem is that they're all now 'Read only'. Is there a way I can solve this problem at a stroke, without having to convert individual files to 'read & write'. Doing that is starting to drive me mad ...
    Thanks!

    Hey there,
    One solution is to repair disk permissions, which can be done through Disk Utility. The article below provides step-by-step instructions for using this feature to repair permissions. It is a better idea to use Disk Utility from your Mac Installation disc for this procedure. More on using disk utility can be found in the Apple document below. Hope this helps.
    http://www.askdavetaylor.com/whyis_my_mac_hard_drive_suddenlyreadonly.html
    http://support.apple.com/kb/HT1452
    B-rock

  • [SOLVED] Root mounted as "Read-only filesystem". mkinitcpio issue?

    I am currently in the middle of setting up system encryption with LUKS. I have been making good progress so far, but I do have one remaining issue.
    After typing my LUKS password, the Linux kernel starts to complain that root is a read-only filesystem. "Starting NetworkManager... cannot touch file XYZ: Read-only filesystem". When it has finally finished booting, I am dropped into a TTY. I can log in and cat my files, but I cannot write to any files our use any programs that do (like pacman).
    I wonder if this is an mkinitcpio issue, but I am not sure. For whatever it's worth, here's my basic setup:
    * /dev/sda1: Boot
    * /dev/sda2: Swap
    * /dev/sda3: Root (LUKS/ext4)
    * menu.lst looks like this
    * /etc/fstab contains this line:
    /dev/mapper/root / ext4 defaults 0 1
    * /etc/mkinitcpio.conf contains these lines:
    MODULES="ext4"
    HOOKS="base udev pata scsi sata encrypt filesystems"
    edit: I should note that I did reinstall the kernel after making those edits to mkinitcpio.conf.
    Any idea what I'm doing wrong? As always, I really do appreciate the help. Thanks in advance!
    Last edited by jalu (2011-04-16 22:14:20)

    So it looks like this major problem was caused by a minor mistake. The file /etc/rc.sysinit was not executable. This made it impossible for the kernel to run the script, which in turn made it impossible for the kernel to mount /dev/sda2 (the swap partition) at /dev/mapper/swap. For some unknown reason, this in turn caused /dev/sda2 to be mounted at /, messing everything up.
    Anyway, a simple sudo chmod +x /etc/rc.sysinit fixed the problem. Thanks for the help, MadTux!

Maybe you are looking for