Scsi error during solaris 8 ia installation

Hi folks,
I try to (re-)install Intel Solaris 8 on my machine and fail getting the error message "Warning: /pci@0,0/pci9005,f@6 (cadp0): timeout: abort request, target=0, lun=0". This varies, sometimes I get "abort device", sometimes "reset bus". Then: "SCSI transport failed, reason: timeout (or reason reset)". Can anyone give me a hint what to do about that?
- I am using an Adaptec 7890 scsi controller. My dealer ensures me that it is not defective and he has successfully installed win95 on it.
- I've been successfully running Solaris 8 on this same machine for quite a while, so hardware is compatible. (Trouble started when I tried to install the recommended patch set. Anything went wrong after that, and nothing short of complete reinstallation would do.)
- I tried webstart installation and interactive installation, same result.
I'd appreciate any help. Thanks in advance!
Bernd.

After all, the hard disk did turn out to be defective inspite of
my dealers protestations. After replacing the disk everything was
fine ...
Not really everything. Something IS wrong with the recommended patch
set (Solaris 8 x86_Recommended Patch Cluster Mar/09/0)! After
installing the patch set my machine refused to boot, and I had to
install the os all over again!

Similar Messages

Error During Solaris 8 Installation

Hi
I am getting the following error message while installing solaris 8 on my intel based computer.
Error : Could not mount filesystems .
Error : could not opern /a/etc/vfstab .
and the installation halts and the prompt comes up.
The packages are partially installed.
Pls help me out in this.
SG Krishnan

At this point in the install there are so many things that could lead
to these errors. I would suggest going right to Sun's Install support
by calling 800 USA-4SUN and following the prompts to warranty
support. There you can verify your hardware compatibility and any
other issue you might have.
Hope this helps.

Not able to add driver update during Solaris 10 installation on IBM x3550

I am facing a problem with installation of Solaris 10 on IBM x3550.
My question is not specific to IBM server.
I am trying to add SAS driver during Solaris 10 installation. I selected option "Apply device driver update" (option # 4). It is asking to insert driver disk. But only showing floppy (f) and cdrom (c).
IBM server 3550 doesnt have floppy drive and I have the driver image only in a USB stick. Unfortunately, Solaris 10 installation is not showing usb device during driver installation.
Is there any way we can add usb device to the driver update disk list??
Thanks in advance.

Does no one have an idea?

Getting error during the Oracle9i installation "Oracle9i Database Release 2 (9.2.0.1.0) for Compaq Tru64 machine"

Hi All,
Getting follwing error during the Oracle9i installation “Oracle9i Database Release 2 (9.2.0.1.0) for Compaq Tru64 machine"
u01/app/oracle/product/9.2.0/install/make.log
- Linking Oracle
rm -f /u01/app/oracle/product/9.2.0/rdbms/lib/oracle
cc -L/u01/app/oracle/product/9.2.0/lib/ -L/u01/app/oracle/product/9.2.0/rdbms/lib -o /u01/app/oracle/product/9.2.0/rdbms/lib/oracla
ld:
load_whole_file: Could not malloc 31328. bytes, for /u01/app/oracle/product/9.2.0/lib//libn9.a(asndata.o), didnt attempt to mmap
Stop.
*** Exit 1
While checked the memory details in the machine its showing plenty of free virtual memory.
# ps aux
USER PID %CPU %MEM VSZ RSS TTY S STARTED TIME COMMAND
oracle 1353 0.6 27.2 601M 555M pts/2 S N 09:14:07 5:49.67 /tmp/OraInstall2014-01-21_09-14-02AM/jre/bin/../bin/alpha/native_threads/java -Doracle.installe
root 3033 0.0 0.4 10.4M 7.7M pts/0 R + 10:59:44 0:00.06 ps aux
oracle 1351 0.0 0.0 2.46M 320K pts/2 I N 09:14:02 0:01.36 ksh /tmp/OraInstall2014-01-21_09-14-02AM/installer -Doracle.installer.library_loc=/tmp/OraInsta
oracle 1277 0.0 0.0 2.48M 312K pts/2 I + 09:02:44 0:00.04 -ksh (ksh)
root 1269 0.0 0.0 2.56M 232K pts/2 I 09:01:23 0:00.01 -sh (sh)
root 1268 0.0 0.0 5.31M 768K ?? I 09:01:22 0:00.11 /usr/bin/X11/xterm -ls
root 1 0.0 0.0 608K 96K ?? IL 08:45:31 0:00.08 /sbin/init -a
root 0 0.0 3.9 2.52G 79M ?? R < 08:45:31 0:23.16 [kernel idle]
And I have rebooted the machine still also getting the same error.
Is there any way to resolve this issue??
Regards
prasanta

Pl elaborate the business / technical reason for installing a 15+ year old unsupported software on a 15+ year old unsupported hardware, assuming you are installing an a supported OS version
HTH
Srini

Error during ecc6.0 installation ..plz help asap

Hi all
i am installing ecc 6.0 on windows 2003 standard 64 bit
with database ibm db2 version 9
i am getting the following error during the installation phase
error during abap import phase
i am attaching error log files
import.monitor.log
===============================================================
INFO: 2007-05-03 22:17:51
Import Monitor is started.
CONFIG: 2007-05-03 22:17:51
Application options:
dbCodepage=1100
dbType=DB6
extFiles=no
importDirs=E:\idesins\51032413\1of6\EXP1;E:\idesins\51032413\2of6\EXP2;E:\idesins\51032413\3of6\EXP3;E:\idesins\51032413\4of6\EXP4;E:\idesins\51032413\5of6\EXP5;E:\idesins\51032413\6of6\EXP6;E:\idesins\51032413\6of6\EXP7;E:\idesins\51032413\6of6\EXP8;E:\idesins\51032413\6of6\EXP9;E:\idesins\51032413\6of6\EXP10;E:\idesins\51032413\6of6\EXP11
installDir=C:\Program Files\sapinst_instdir\ERP\SYSTEM\DB6\CENTRAL\AS
jobNum=3
loadArgs= -stop_on_error -loadprocedure fast
monitorTimeout=30
orderBy=
r3loadExe=E:\usr\sap\IDE\SYS\exe\nuc\NTAMD64\R3load.exe
sapinst=
trace=all
tskFiles=yes
CONFIG: 2007-05-03 22:17:51
List of packages with table structure: 'SAP0000'.
CONFIG: 2007-05-03 22:17:51
List of packages with views: 'SAPVIEW'.
TRACE: 2007-05-03 22:17:51 com.sap.inst.migmon.imp.ImportStandardTask preCreate
Parse of 'C:\Program Files\sapinst_instdir\ERP\SYSTEM\DB6\CENTRAL\AS\DDLDB6.TPL' template file is started.
INFO: 2007-05-03 22:17:51 com.sap.inst.migmon.imp.ImportStandardTask preCreate
Parse of 'C:\Program Files\sapinst_instdir\ERP\SYSTEM\DB6\CENTRAL\AS\DDLDB6.TPL' template file is successfully completed.
Primary key creation: after load.
Index creation: after load.
INFO: 2007-05-03 22:17:51
Data codepage 4103 is determined using TOC file 'E:\idesins\51032413\1of6\EXP1\DATA\SAPAPPL0.TOC' for package 'SAPAPPL0'.
INFO: 2007-05-03 22:17:53
Version table 'SVERS' is found in STR file 'E:\idesins\51032413\4of6\EXP4\DATA\SAPSDIC.STR' from package 'SAPSDIC'.
INFO: 2007-05-03 22:17:53
Data conversion tables 'DDNTF,DDNTF_CONV_UC,DDNTT,DDNTT_CONV_UC' are found in STR file 'E:\idesins\51032413\4of6\EXP4\DATA\SAPSDIC.STR' from package 'SAPSDIC'.
TRACE: 2007-05-03 22:17:53 com.sap.inst.migmon.LoadTask run
Loading of 'SAPSDIC' import package is started.
TRACE: 2007-05-03 22:17:53 com.sap.inst.migmon.LoadTask processPackage
Task file generation for 'SAPSDIC' import package:
E:\usr\sap\IDE\SYS\exe\nuc\NTAMD64\R3load.exe -ctf I E:\idesins\51032413\4of6\EXP4\DATA\SAPSDIC.STR "C:\Program Files\sapinst_instdir\ERP\SYSTEM\DB6\CENTRAL\AS\DDLDB6.TPL" SAPSDIC.TSK DB6 -l SAPSDIC.log
TRACE: 2007-05-03 22:17:53 com.sap.inst.migmon.LoadTask processPackage
Loading of 'SAPSDIC' import package into database:
E:\usr\sap\IDE\SYS\exe\nuc\NTAMD64\R3load.exe -i SAPSDIC.cmd -dbcodepage 1100 -l SAPSDIC.log -stop_on_error -loadprocedure fast
ERROR: 2007-05-03 22:17:53 com.sap.inst.migmon.LoadTask run
Loading of 'SAPSDIC' import package is interrupted with R3load error.
Process 'E:\usr\sap\IDE\SYS\exe\nuc\NTAMD64\R3load.exe -i SAPSDIC.cmd -dbcodepage 1100 -l SAPSDIC.log -stop_on_error -loadprocedure fast' exited with return code 2.
For mode details see 'SAPSDIC.log' file.
Standard error output:
sapparam: sapargv( argc, argv) has not been called.
sapparam(1c): No Profile used.
sapparam: SAPSYSTEMNAME neither in Profile nor in Commandline
WARNING: 2007-05-03 22:18:21
Cannot continue import because not all import packages with data conversion tables are loaded successfully.
WARNING: 2007-05-03 22:18:21
1 error(s) during processing of packages.
INFO: 2007-05-03 22:18:21
Import Monitor is stopped.
=============================================================
import.monitor.java.log
======
java version "1.4.2_14"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.4.2_14-b05)
Java HotSpot(TM) 64-Bit Server VM (build 1.4.2_14-b05, mixed mode)
Import Monitor jobs: running 1, waiting 18, completed 0, failed 0, total 19.
Loading of 'SAPSDIC' import package: ERROR
Import Monitor jobs: running 0, waiting 18, completed 0, failed 1, total 19.
=========================
sapsdic.log
E:\usr\sap\IDE\SYS\exe\nuc\NTAMD64\R3load.exe: sccsid @(#) $Id: //bas/700_REL/src/R3ld/R3load/R3ldmain.c#8 $ SAP
E:\usr\sap\IDE\SYS\exe\nuc\NTAMD64\R3load.exe: version R7.00/V1.4
Compiled Aug 31 2006 22:40:33
E:\usr\sap\IDE\SYS\exe\nuc\NTAMD64\R3load.exe -i SAPSDIC.cmd -dbcodepage 1100 -l SAPSDIC.log -stop_on_error -loadprocedure fast
(DB) INFO: connected to DB
(DB) ERROR: DDL statement failed
(CREATE TABLE "/SDF/PAT03" ( "PATCH" SAPDB6VARCHAR(20) DEFAULT ' ' NOT NULL , "SHORT_TEXT" SAPDB6VARCHAR(60) DEFAULT ' ' NOT NULL , "STATUS" SAPDB6FIXCHAR(1) DEFAULT ' ' NOT NULL , "DELIV_DATE" SAPDB6VARCHAR(8) DEFAULT '00000000' NOT NULL , "DELIV_TIME" SAPDB6VARCHAR(6) DEFAULT '000000' NOT NULL , "RESPONSIBL" SAPDB6VARCHAR(12) DEFAULT ' ' NOT NULL , "IMPLE_DATE" SAPDB6VARCHAR(8) DEFAULT '00000000' NOT NULL , "IMPLE_TIME" SAPDB6VARCHAR(6) DEFAULT '000000' NOT NULL , "L_IMPL_REL" SAPDB6VARCHAR(4) DEFAULT ' ' NOT NULL , "CONFLICTS" SAPDB6FIXCHAR(1) DEFAULT ' ' NOT NULL , "CONFIRMED" SAPDB6FIXCHAR(1) DEFAULT ' ' NOT NULL , "BACKUP" SAPDB6VARCHAR(20) DEFAULT ' ' NOT NULL , "FROM_REL" SAPDB6VARCHAR(4) DEFAULT ' ' NOT NULL , "TO_REL" SAPDB6VARCHAR(4) DEFAULT ' ' NOT NULL , "OS" SAPDB6VARCHAR(10) DEFAULT ' ' NOT NULL , "DB" SAPDB6VARCHAR(10) DEFAULT ' ' NOT NULL , "PATCH_TYPE" SAPDB6VARCHAR(3) DEFAULT ' ' NOT NULL , "ANCESTOR" SAPDB6VARCHAR(20) DEFAULT ' ' NOT NULL , "STRICT_SEQ" SAPDB6FIXCHAR(1) DEFAULT ' ' NOT NULL , "NO_GEN" SAPDB6FIXCHAR(1) DEFAULT ' ' NOT NULL , "SPAMFIX" SAPDB6FIXCHAR(1) DEFAULT ' ' NOT NULL , "ADDON_ID" SAPDB6VARCHAR(10) DEFAULT ' ' NOT NULL , "ADDON_REL" SAPDB6VARCHAR(12) DEFAULT ' ' NOT NULL , "IGN_CONFLI" SAPDB6FIXCHAR(1) DEFAULT ' ' NOT NULL , "AP_ANCEST" SAPDB6VARCHAR(20) DEFAULT ' ' NOT NULL , "EPSFILSIZ" SAPDB6VARCHAR(4) DEFAULT ' ' NOT NULL , "HI_ANCEST" SAPDB6VARCHAR(2) DEFAULT ' ' NOT NULL , "COMP_REL" SAPDB6VARCHAR(10) DEFAULT ' ' NOT NULL , "COMPONENT" SAPDB6VARCHAR(30) DEFAULT ' ' NOT NULL ) IN IDE#DDICD INDEX IN IDE#DDICI LONG IN IDE#DDICD)
DbSlExecute: rc = 102
(SQL error -601)
error message returned by DbSl:
SQL0601N The name of the object to be created is identical to the existing name "SAPIDE./SDF/PAT03" of type "TABLE". SQLSTATE=42710
(DB) INFO: disconnected from DB
E:\usr\sap\IDE\SYS\exe\nuc\NTAMD64\R3load.exe: job finished with 1 error(s)
E:\usr\sap\IDE\SYS\exe\nuc\NTAMD64\R3load.exe: END OF LOG: 20070503221753
=============================================
any help will be much appreciated.
thanks.
Message was edited by:
Abdul Wahid Khan

Hi,
Restart the installation from the begining
Regards
Umesh K

Error during Database instance installation of NW04s Portal installation

Hello All,
 This is our system environment:
 Portal - NW04s SR1 (SCS instance on one host) -- finished successfully
 Database - MS SQL Server 2005 on a separate host
We are doing a domain installation. The database was installed successfully, but when trying to install the database instance during the NW04s installation, I am getting the following errors:
ERROR 2007-01-03 11:30:10 [syxxsyshlp.cpp:78]
 syslib::printOSError(const iastring &, int, DWORD, const iastring &, CMessage::eLogMessage) FSL-00001 System call failed. Error 5 (Access is denied.
) in execution of system call 'CopyFile' with parameter (
DCASAPHR05\sapmnt\EPD\SYS\profile\DEFAULT.PFL,
DCASAPHR05\sapmnt\EPD\SYS\profile\DEFAULT.1.PFL, FALSE), line (478) in file (synxcfile.cpp).
ERROR 2007-01-03 11:30:10 [syxxcnode.cpp:402]
 CSyNodeImpl::move(const CSyPath &
DCASAPHR05/sapmnt/EPD/SYS/profile/DEFAULT.1.PFL, ISyNode::CopyMoveMode_t 0x3) FSL-02039 Unable to move or rename node
DCASAPHR05/sapmnt/EPD/SYS/profile/DEFAULT.PFL with type file/directory to
DCASAPHR05/sapmnt/EPD/SYS/profile/DEFAULT.1.PFL: Overlapped I/O operation is in progress.
ERROR 2007-01-03 11:30:10
 CJSlibModule::writeError_impl() MUT-03025 Caught ESyException in Modulecall: ESAPinstException: error text undefined.
ERROR 2007-01-03 11:30:10 [iaxxgenimp.cpp:736]
 showDialog() FCO-00011 The step createDefaultProfile with step key |NW_Java_DB|ind|ind|ind|ind|0|0|NW_System|ind|ind|ind|ind|6|0|createDefaultProfile was executed with status ERROR .
Could anybody please help me through this process?
Thanks much in advance,
Sunitha

Hi,
I would try adding epdadm and SAPServiceEPD accounts to Administrators group and give Administrators full access to sapmnt shared area. Also double check SAP_EPD_GlobalAdmin domain admin authority and SAP_LocalAdmin and SAP_EPD_LocalAdmin accounts.
Open
DCASAPHR05\sapmnt\EPD\SYS\profile folder using explorer and created file and see if there is any authorzation issues with domail\sapinst account.
good luck
Kondala Rao

Error during Extension Builder installation on Mac OS

I downloaded extension builder 2.1 trial version from adobe website: Extension_Builder_2_1_LS1_trial.dmg
When I try to install it, at the end of the installation process, during "validating packages" process it stops and shows me "The installation failed. The installer encountered an error that caused the installation to fail. Contact software manufacturer...".
1. System: OS X v. 10.9 (mavericks)
2. I have Flash Builder 4.7 premium installed on my computer.
3. I have Photoshop CC installed on my computer.
What may be the cause of installation errors?
What do you suggest?
Is there any other version of Extension Builder than I could try to install?

This is not an Adobe error message. Please check your system to rule out any environmental issues such as insufficient hard disk space (2G or so needed after you copied the installer since it will need to unpack some installation files), pending system reboot, download file corrupted etc. then retry installation.

Error during iTunes 10 installation - iPod Service failed to start

Hi Everyone,
I am getting this error during installation of iTunes 10(Windows XP).
+*"Service (iPod Service)failed to start.Verify that you have sufficient priveleges to start system services."*+
*Can any of you please help?* I ignored it first and continued with the installation. Then tried to update iphone to iOS 4.1 which crashed. I had to go to Apple store to get my iphone restored. I am having trouble installing itunes and cannot restore data from backup.
I tried uninstalling itunes and deleted all itunes data as suggested by the guy at the Apple store. Still not working. Will appreciate if someone can help resolve this error. Thanks.

I just got off the phone with Apple tech support. The problem with that iPod Service is a problem with XP Service Pack 3, but can be fixed this way:
1. Right click on "My Computer", select "Properties"
2. Click on the Advanced tab.
3. in the Startup and Recovery section, click the Settings button.
4. Click the Edit byutton to edit your boot.ini file in notepad.
5. Look for "/noexecute=" in the file and change the word after the equals to "optin" (sorry - I don't remember what the original setting was anymore).
6. Save the file, close notepad, click the OK button on Startup and Recovery window, then reboot.
The warning message about the iPod Service should stop. Also, this helps with iPhones that are not recognized by Windows or iTunes after an install fails.

URGENT- checksum error during database instance installation

Hi Experts and Developers,
I would be glad,if you can help me solve this.
I did not have any problem during Central instance installation.But getting 2 checksum errors during my database instance installation.
The log file for 1st error says
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: START OF LOG: 20060917024333
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: sccsid @(#) $Id: //bas/640_REL/src/R3ld/R3load/R3ldmain.c#6 $ SAP
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: version R6.40/V1.4 [UNICODE]
C:\usr\sap\SAA\SYS\exe\run/R3load.exe -ctf I E:/DVD1/EXPORTS/EXP1/DATA/SAPSSEXC.STR C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/DDLORA.TPL C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/SAPSSEXC.TSK ORA -l C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/SAPSSEXC.log
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: job completed
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: END OF LOG: 20060917024333
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: START OF LOG: 20060917024703
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: sccsid @(#) $Id: //bas/640_REL/src/R3ld/R3load/R3ldmain.c#6 $ SAP
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: version R6.40/V1.4 [UNICODE]
C:\usr\sap\SAA\SYS\exe\run/R3load.exe -dbcodepage 4103 -i C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/SAPSSEXC.cmd -l C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/SAPSSEXC.log -stop_on_error
DbSl Trace: ORA-1403 when accessing table SAPUSER
(DB) INFO: connected to DB
(DB) INFO: DbSlControl(DBSL_CMD_NLS_CHARACTERSET_GET): UTF8
Syslog: k xxx : rscpexcc 11
(rscpsumg) Please look also into "C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/SAPSSEXC001.xml".
Syslog: k CQ3 : UMGSETTING& rscpexcc 12
(DB) INFO: BRATEXT created #20060917024719
(IMP) INFO: import of BRATEXT completed (259725 rows) #20060917024803
(DB) INFO: BRATEXT~0 created #20060917025001
(DB) INFO: D010INC created #20060917025001
(IMP) INFO: import of D010INC completed (338126 rows) #20060917025011
(((((I did copy only the first and last few lines))))
(DB) INFO: DM45T~0 created #20060917030515
(DB) INFO: DM46S created #20060917030515
(IMP) INFO: import of DM46S completed (99 rows) #20060917030516
(DB) INFO: DM46S~0 created #20060917030516
(DB) INFO: DM46S~A created #20060917030516
(DB) INFO: DOKCLU created #20060917030516
(RFF) ERROR: invalid checksum in data file "E:/DVD1/EXPORTS/EXP1/DATA/SAPSSEXC.001"
 current table was "DOKCLU"
(DB) INFO: disconnected from DB
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: job finished with 1 error(s)
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: END OF LOG: 20060917030913
The log file for second error says
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: START OF LOG: 20060917024334
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: sccsid @(#) $Id: //bas/640_REL/src/R3ld/R3load/R3ldmain.c#6 $ SAP
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: version R6.40/V1.4 [UNICODE]
C:\usr\sap\SAA\SYS\exe\run/R3load.exe -ctf I E:/DVD1/EXPORTS/EXP2/DATA/SAPAPPL1.STR C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/DDLORA.TPL C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/SAPAPPL1.TSK ORA -l C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/SAPAPPL1.log
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: job completed
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: END OF LOG: 20060917024335
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: START OF LOG: 20060917024703
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: sccsid @(#) $Id: //bas/640_REL/src/R3ld/R3load/R3ldmain.c#6 $ SAP
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: version R6.40/V1.4 [UNICODE]
C:\usr\sap\SAA\SYS\exe\run/R3load.exe -dbcodepage 4103 -i C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/SAPAPPL1.cmd -l C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/SAPAPPL1.log -stop_on_error
DbSl Trace: ORA-1403 when accessing table SAPUSER
(DB) INFO: connected to DB
(DB) INFO: DbSlControl(DBSL_CMD_NLS_CHARACTERSET_GET): UTF8
Syslog: k xxx : rscpexcc 11
(rscpsumg) Please look also into "C:\Program Files\sapinst_instdir\NW04SR1\WEBAS_ABAP_ORA_UC\DB/SAPAPPL1001.xml".
Syslog: k CQ3 : UMGSETTING& rscpexcc 12
(DB) INFO: /SAPDMC/LSOFIL created #20060917024728
(IMP) INFO: import of /SAPDMC/LSOFIL completed (0 rows) #20060917024728
(DB) INFO: /SAPDMC/LSOFIL~0 created #20060917024729
(DB) INFO: /SAPDMC/LSOFIW created #20060917024729
(IMP) INFO: import of /SAPDMC/LSOFIW completed (0 rows) #20060917024729
(DB) INFO: /SAPDMC/LSOFIW~0 created #20060917024730
 (((( I did copy only first and last few lines of this log file ))))
(DB) INFO: IDXRCVPOR created #20060917025240
(IMP) INFO: import of IDXRCVPOR completed (0 rows) #20060917025240
(DB) INFO: IDXRCVPOR~0 created #20060917025241
(DB) INFO: IDXRCVPOR~TIM created #20060917025241
(DB) INFO: INDX created #20060917025241
(RFF) ERROR: invalid checksum in data file "E:/DVD1/EXPORTS/EXP2/DATA/SAPAPPL1.001"
 current table was "INDX"
(DB) INFO: disconnected from DB
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: job finished with 1 error(s)
C:\usr\sap\SAA\SYS\exe\run/R3load.exe: END OF LOG: 20060917025244
For your understanding ,
Here are the steps that i followed,
(1)I am Installing SAP XI on Windows 2003 server standard edition with oracle 9i as database.
(2)I copied the DVDs to HARD DRIVE
(3)I created the Microsoft Loopback adapter,assigned an ip.
(4) Then installed j2sdk 1.4.2 for windows
(5) installed central instance with SAPinst

Hi Carsten,
Thank you for taking a look at my problem.
I am using NW_2004_SR1 (Netweaver 2004 SR1).
Just for your information, the size for those two files on my Hard drive are
SAPSSEXC.001 is 650,240 Kb
SAPAPPL1.001 is 126,608 Kb
and my label.asc in Exports directory is
SAP:NETWEAVER:04SR1:DVD_EXPORT:NETWeaver 04 SR 1 EXPORT DVD:D51030721
label.asc in EXP1 directory is
SAP:NETWEAVER:04SR1:EXPORT(1/3):NetWeaver 04 SR 1 Export CD 1/3:CDxxxxxxxx
label.asc in EXP2 is
SAP:NETWEAVER:04SR1:EXPORT(2/3):NetWeaver 04 SR 1 Export CD 2/3:CDxxxxxxxx
label.asc in EXP3 directory is
SAP:NETWEAVER:04SR1:EXPORT(3/3):NetWeaver 04 SR 1 Export CD 3/3:CDxxxxxxxx
Thank you,

Error during Database Instance Installation

Hi,
We are installing SAP CRM 4.0.Central Instance Installation is over without problem.However during Database Instance Installation we are getting an Error which says :
"The node E:\sap\DATA does not exist".
I created this folder manually.Then is gave another error saying
"Node C:\Program Files\sapinst_instdir\CRM_40SR1_ABAP_UC\DB\CRM\DATA does not exist."
I created this again.Then it gave another Error saying :
"Node C:\Program Files\sapinst_instdir\CRM_40SR1_ABAP_UC\DB\4.0\DATA does not exist."
Why is this error coming up again and again and any solution to this problem?
Thanks,
Suparna

This is happening because installation program is checking the existence of DB Export directories which you specified to the installation program. It has to do with the installation screen where you specify the location of your DB Export CD/DVD during installation of Database instance. Usually what helps is if you copy the DB Export CD's to a directory in your hard disk and specify that as the target for copy. Just check what you are specifying DB Export parameter screen.
Cheers,
Sanjeev

Fatal Error during Live Office Installation

Hi Friends,
I am facing issue in Live Office.
I had installated Live Office but since the Live Office option was not seen in any of the MS Office applications so I tried to uninstall Live Office software.
But its giving me Fatal Error during installation.
Could you please let me know how can I reinstall only BO Live Office software.
Thanks in advance.
Regards
Sindhu

Hi Shubhodeep,
The Live Office version is 3.1
MS OFfice: 2003
Also, I ahve installated BO XI3.1 server.
Earlier it everything was working fine.
Later as the Live office icon was not seen in the Excel so I tried repair it.
After that I am getting this problem: nFata error during installation.
I tried rintsllaing entire BO 3.1 setup completly by cleaning the resigstry. But that also did not help.
It would be great if someone can provide any solution ASAP.
Thnaks
Sindhu

Error No disks Found during Solaris 10 installation

Hi,
i am trying to install Solaris 10 x86 on an Ml370 server that we bought. during the installation it gives the error No Disks Found. how can i correct this problem?

One question:
Does this server ,ML370 G5, support Solaris in 64 bit mode?
http://www.sun.com/bigadmin/hcl/data/systems/details/1891.html doesn't indicate if it is certified for 64 bits.
and http://h71028.www7.hp.com/enterprise/cache/493913-0-0-0-121.html indicates ony 32 bits.

Equium A100-549: Blue Screen error during Recovery CD installation

Hey,
I recently purchased a Toshiba laptop, everything worked perfectly until my laptop was attacked. I got rid of the virus and went to reformat due to lots of problems occurring. The main one being a error has accursed and "Blah Blah" program needs to close. Also i kept getting loads of errors.
http://aumha.org/win5/kbestop.htm
Them types.
Now then the Toshiba reformatting disk said simply put the disk into the CD drive and turn off. I did this, great. The toshiba disk said press F12 upon starting and click run the CD. The CD fires up and gets half way thro reformatting.
I suddenly get a blue screen error. I thought oh well ill reboot and carry on. This is where the problem started. Because i was half way thro deleting/reinstalling windows i was missing some files. I go to reinstall or try to use the Toshiba CD I get a blue screen error.
0x00000050: PAGE_FAULT_IN_NONPAGED_AREA
(Click to consult the online Win XP Resource Kit article, or see Windows 2000 Professional Resource Kit, p. 1548.)
Requested data was not in memory. An invalid system memory address was referenced. Defective memory (including main memory, L2 RAM cache, video RAM) or incompatible software (including remote control and antivirus software) might cause this Stop message, as may other hardware problems (e.g., incorrect SCSI termination or a flawed PCI card).
Any ideas what i can do? I don't want to send the laptop back to Toshiba to fix however im thinking this is the only way out.
Please if repplying try to keep technical lanuage to a minnium. Many thanks, Dan.

Hi
Its very strange because the installation from the Toshiba recovery CD should works properly and without any Blue screen messages.
Usually if the BSOD appears if there is a serious software problem or something wrong with the hardware.
I dont think that the software on the recovery CD could be corrupt.
Did you try to install the OS from original Microsoft Windows CD? It would be very interesting to know if the blue screen will also appear.
However, I think your notebook is new and the warranty is valid. In my opinion you should ask the Toshiba service partner for the help because the guys could start the diagnostic test and could locate the fault.

Error during 9.3 installation on vista 64

Hello,
It's impossible to install last 9 version (or 8 version) on my new PC (Vista 64).
The error occurs at last step and the message is : an error occured during installation of assembly component.
Is there somebody can help me ?
Thanks,
Dominique

I'm having the same problem on vista 64. I keep getting a permission problem installing to "Program Files (x86)". The instructions on the adobe website say to change ownership on the ProgramData folder which doesn't help. I tried redirecting the install to ProgramData but it still tries to write to (x86) folder. I tried changing ownership of Program Files(x86)/adobe and that didn't work. I can't even vew that folder. I am working from an administrator account. Please help.

Java-Error during Solution Manager Installation

During the Installation at point "Prepare to install minimal configuration" I'm getting the following error message:
An error occurred while processing option SAP Solution Manager 7.1 > SAP Systems > MS SQL Server > Central System > Central System( Last error reported by the step :Assertion failed: in
function NW_Call_Offline_CTC_ind_ind_ind_ind_SubComponentContainer_callOfflineCTC() {
 var nw = NWInstall.getSystem(context.get("sid"));
 var ctcDirFs = nw.getCI().getInstanceDir().concat("j2ee", "ctc");
 var ctcExeFile = installer.onWindows() ? "LaunchOfflinectc.bat" : "LaunchOfflinectc.sh";
 var ctcCall = ctcDirFs.concat(ctcExeFile);
 installer.writeTrace("CTC is in" + ctcCall);
 ASSERT(arguments.callee, ctcCall.isExisting(), "CTC executable cannot be found in " + ctcCall.toString());
 var pmgt = new ProcessMgt();
 var app = pmgt.createChildApplication(ctcCall, []);
 var userData = nw.getUsers().getAccountData(NWUsers.roles.SIDAdm);
 var user = (new AccountMgt()).getUser(userData.name);
 var env = pmgt.getProcessEnvironment();
 if (installer.onUnix()) {
 env.setUser(user);
 } else {
 if (installer.onOS400()) {
 env.setUser(user);
 env.setGroup(user.getPrimaryGroup());
 env.setKernelLibrary(nw.getOS4_Krnlib());
 env.setWorkingDirectory(ctcDirFs.getNode());
 var javaHome = nw.getJavaHome().toString();
 env.setEnvironmentVariable(new Property("JAVA_HOME", javaHome));
 installer.writeTrace("For the Offline CTC Call, JAVA_HOME is set to " + env.getEnvironmentVariable("JAVA_HOME"));
 app.setEnvironment(env);
 var retval = app.run([], true);
 ASSERT(arguments.callee, retval == 0, "CTC retval is not 0 but " + retval);
 installer.writeTrace("CTC has been called in Offline Mode.");
CTC retval is not 0 but 1)
As a JVM I'm using the version provided by SAP on DVD, JDK is ver6_26-rev_b21, JCE_policy is version 6.
Can anyone help me here?

WARNING 2011-12-07 13:09:36.864
Execution of the command "C:\usr\sap\DSM\DVEBMGS00\j2ee\ctc\LaunchOfflinectc.bat" finished with return code 1. Output:
 1 file(s) copied.
java.io.BufferedInputStream@4a4e79f1
Dec 7, 2011 1:09:34 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Info: Start Execution of Offline CTC TemplatInstaller
Dec 7, 2011 1:09:34 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Info: Looking for initial Properties in file '../../../config/usagetypes.properties'
Dec 7, 2011 1:09:34 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Info: Loading of initial Properties-File successful
Dec 7, 2011 1:09:34 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Info: Selected Usages:SolManager:SolManager Java
PerfTimes : loadNativeLayer: loading jperflib failed. no jperflib in java.library.path
Dec 7, 2011 1:09:36 PM ...ProviderFactory.initalize(Context)_1! [Thread[main,5,main]] Info:
Dec 7, 2011 1:09:36 PM ...rovider(ConfigurationProviderFactory) [Thread[main,5,main]] Info: !BrokerRegistry.register!ConfigManagerProvider
Dec 7, 2011 1:09:36 PM ...DataModelRepository.registerExtension [Thread[main,5,main]] Path: entering 'registerExtension'
Dec 7, 2011 1:09:36 PM ...DataModelRepository.registerExtension [Thread[main,5,main]] Info: registering extensions for 'http://www.sap.com/ctc/configurationmanager'
Dec 7, 2011 1:09:36 PM ...DataModelRepository.registerExtension [Thread[main,5,main]] Path: entering 'registerExtension'
Dec 7, 2011 1:09:36 PM ...DataModelRepository.registerExtension [Thread[main,5,main]] Info: registering extensions for 'http://www.sap.com/ctc/configurationmanager'
Dec 7, 2011 1:09:36 PM ...onControllerImpl.startUpProcessEngine [Thread[main,5,main]] Path: entering 'startUpProcessEngine'
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: The class XMLPathUtil_1_5 is not supported in 7.0
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: java.lang.IllegalStateException:The class XMLPathUtil_1_5 is not supported in 7.0
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.metamodel.util.XMLPathUtil_1_5:getStringValue25
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.metamodel.util.XMLPathUtil:getStringValue161
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.metamodel.process.transform.XML2Action:transformInternal390
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.metamodel.process.transform.XML2Action:transform118
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.metamodel.process.transform.XML2Action:transform89
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.metamodel.process.transform.XML2JavaProcessFactory:lightLoadProcessFromXML191
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.metamodel.process.controller.ProcessRegistry:loadProcess402
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.metamodel.process.controller.ProcessRegistry:getVisibleProcessesInternal350
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.metamodel.process.controller.ProcessRegistry:getVisibleRootProcesses222
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.metamodel.process.controller.ProcessEngine:getVisibleRootProcesses489
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.OfflineTemplateImporterJAR:executeWizard121
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.tc.lm.ctc.OfflineTemplateImporterJAR:main585
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: sun.reflect.NativeMethodAccessorImpl:invoke0-2
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: sun.reflect.NativeMethodAccessorImpl:invoke39
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: sun.reflect.DelegatingMethodAccessorImpl:invoke25
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: java.lang.reflect.Method:invoke597
Dec 7, 2011 1:09:36 PM ....tc.lm.ctc.OfflineTemplateImporterJAR [Thread[main,5,main]] Error: com.sap.engine.offline.OfflineToolStart:main81
Program terminated abnormally

Scsi error during solaris 8 ia installation

Similar Messages

Maybe you are looking for