SCSI warnings - Solaris 10 Install - Netra 240

Hi Friends,
Im doing some installation using Netra 240 & I've external storage (Via Store Edge S1) - However after i finished the installation I keep getting this messages on the console.
Im not sure what these messages are. If anyone can throw some lo
i keep getting these messages,
ct 13 08:01:15 C69N2 got SCSI bus reset
Oct 13 08:01:15 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd5):
Oct 13 08:01:15 C69N2 auto request sense failed (reason=reset)
Oct 13 08:01:21 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2 (glm0):
Oct 13 08:01:21 C69N2 Resetting scsi bus, got incorrect phase from (0,0)
Oct 13 08:01:21 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2 (glm0):
Oct 13 08:01:21 C69N2 got SCSI bus reset
Oct 13 08:01:21 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd5):
Oct 13 08:01:21 C69N2 auto request sense failed (reason=reset)
Oct 13 08:01:24 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd5):
Oct 13 08:01:24 C69N2 drive offline
Oct 13 08:01:24 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd5):
Oct 13 08:01:24 C69N2 i/o to invalid geometry
Oct 13 08:01:24 C69N2 md_stripe: WARNING: md: d17: write error on /dev/dsk/c1t0d0s7
Oct 13 08:01:27 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2 (glm0):
Oct 13 08:01:27 C69N2 Resetting scsi bus, got incorrect phase from (0,0)
Oct 13 08:01:27 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2 (glm0):
Oct 13 08:01:27 C69N2 got SCSI bus reset
Oct 13 08:01:27 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd5):
Oct 13 08:01:27 C69N2 auto request sense failed (reason=reset)
Oct 13 08:01:33 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2 (glm0):
Oct 13 08:01:33 C69N2 Resetting scsi bus, got incorrect phase from (0,0

bash-3.00#
bash-3.00# iostat -En
c1t1d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: SEAGATE Product: ST373453LSUN72G Revision: 0449 Serial No: 0444J28H3B
Size: 73.40GB <73400057856 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c0t0d0 Soft Errors: 2 Hard Errors: 0 Transport Errors: 1
Vendor: TEAC Product: DV-28E-C Revision: 1.4B Serial No:
Size: 0.00GB <0 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 2 Predictive Failure Analysis: 0
c1t0d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: SEAGATE Product: ST373453LSUN72G Revision: 0449 Serial No: 0448J2F3JK
Size: 73.40GB <73400057856 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c2t12d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: FUJITSU Product: MAT3147N SUN146G Revision: 0602 Serial No: 0513C0144Y
Size: 146.80GB <146800115712 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c2t13d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: FUJITSU Product: MAT3147N SUN146G Revision: 0602 Serial No: 0513C0143U
Size: 146.80GB <146800115712 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c2t14d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: FUJITSU Product: MAT3073N SUN72G Revision: 0602 Serial No: 0512B02E3N
Size: 73.40GB <73400057856 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
bash-3.00#
bash-3.00#

Similar Messages

Netra 240 - SSH not working

We are having a problem with a Sun Netra 240 � (Solaris 10) and are unable to SSH to the server. When entering the login and password � after about 15 seconds it closes out. We had NO trouble last week logging in using secure shell.
We can go to the console port with no problem.
Any ideas as to what might be the problem or fix?
Thanks,

You'll have to upgrade your IOS & license-
"ENTERPRISE PLUS IPSEC 3DES-Supports all the ENTERPRISE PLUS features, plus adds support for Triple Digital Encryption Standard (3DES) encryption to enable features that require this security, such as Secure Shell (SSH) Protocol and IP Security (IPSec) tunnels"
Hope it helps

Sun Netra 240 runs max level POST every power up

Hello, I have a Sun Netra 240 server box that on every power up runs the max level POST which takes a good 5 minutes to complete. I have the power key switch set to the normal position and not DIAG mode and I have the Diag-level set to "off" for the system configuration settings. Nothing gets reported as an error during the POST but it still continues to run full POST on every power cycle. Can anyone tell me what else to check or look at to make it stop? Thanks in advance.

I have no way to get a copy of this from the screen so I had to write it all down and hand jam it in. I only put my values, not the default values. These have not been changed though so I don't think it is any of these settings. Just for some background this server has been fine for the past year or so and then one day it just started doing this out of the blue.
test-args -
diag-passes 1
asr-policy normal
local-mac-address? true
fcode-debug false
silent-mode? false
scsi-initiator-id 7
oem-logo -
oem-logo? false
oem-banner -
oem-banner? false
ansi-terminal true
screen-#col 80
screen-#row 34
ttyb-rts-dtr-off false
ttyb-ignore-cd true
ttya-rts-dtr-off false
ttya-ignore-cd true
ttyb mode 9600,8,n,1,-
ttya mode 9600,8,n,1,-
output-device screen
input-device keyboard
auto-boot-on-error false
load base 16384
auto-boot? true
boot-command boot
diag-device disk
use-NVRAMRC true
security mode command
NVRAMRC devalias radbkup
security-#bad-logins 2
post-trigger power-on-reset
diag-script none
diag-level off
diag-switch false
obdiag-trigger power-on-reset
error-reset-recovery boot
Edited by: 941057 on Jun 15, 2012 2:38 PM

Slow installation for Soaris 5.8 on Netra 240 using DVD

Hello,
I am installaing a Solaris 5.8 sparc OS on Netra 240 using a DVD-RAM.
The installation is very slow (more than 1.5 hours).
Is any configuration needed in the OBP ?
What is the required firmware version ?
Any other options ?
Thanks in advance,
Simcha Behar

Hello,
I am installaing a Solaris 5.8 sparc OS on Netra 240 using a DVD-RAM.
The installation is very slow (more than 1.5 hours).
Is any configuration needed in the OBP ?
What is the required firmware version ?
Any other options ?
Thanks in advance,
Simcha Behar

Problems making Solaris 10 install disk for x86

I have an Ultra 40 M2. I made a boot/install DVD disk with Solaris 10 for x86.
The system just doesn't recognize it at all, like there is nothing in the DVD drive.
What am I doing wrong?
The DVD drive does recognize other DVDs, just not the Solaris 10 install one (I created two install disks to no avail)

How are you burning the DVD. What software/options.
Theres a howto here
http://www.sun.com/software/solaris/self_help.jsp#burning

Solaris 10 instalation in Guest Domain - Timed out waiting for TFTP reply

I have the next trouble
I have a Sun Fire T1000 and i want install two Guest LDOM's with Solaris10 in each one, I Install the LDOM Manager 1.0.3 and the service is "online" also the another services needed
First Setup the 2 Guest LDOM's in the primary Domain sucesfully .... here is a desc of the configuration.
# ldm list-bindings
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME
primary active -n-cv SP 4 1G 0.1% 2h 14m
MAC
00:14:4f:a7:85:1e
VCPU
VID PID UTIL STRAND
0 0 0.2% 100%
1 1 0.2% 100%
2 2 0.1% 100%
3 3 0.1% 100%
MAU
ID CPUSET
0 (0, 1, 2, 3)
MEMORY
RA PA SIZE
0x8000000 0x8000000 1G
VARIABLES
diag-switch?=true
security-#badlogins=0
IO
DEVICE PSEUDONYM OPTIONS
pci@780 bus_a
pci@7c0 bus_b
VCC
NAME PORT-RANGE
primary-vcc0 5000-5100
CLIENT PORT
aplica_srss1@primary-vcc0 5001
aplica_prod@primary-vcc0 5000
VSW
NAME MAC NET-DEV DEVICE MODE
primary-vsw0 00:14:4f:a7:85:1e bge0 switch@0
PEER MAC
vnet2@aplica_srss1 00:14:4f:fb:f4:e0
vnet1@aplica_prod 00:14:4f:fb:2c:60
VDS
NAME VOLUME OPTIONS DEVICE
primary-vds0 vol1 /dev/dsk/c0t0d0s3
CLIENT VOLUME
vdisk1@aplica_prod vol1
VCONS
NAME SERVICE PORT
SP
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME
aplica_prod active -t--- 5000 4 2G 15% 9m
MAC
00:14:4f:fb:2c:60
VCPU
VID PID UTIL STRAND
0 4 35% 100%
1 5 0.0% 100%
2 6 7.0% 100%
3 7 84% 100%
MEMORY
RA PA SIZE
0x8000000 0x48000000 2G
VARIABLES
auto-boot?=true
boot-device=
use-nvramrc?=true
NETWORK
NAME SERVICE DEVICE MAC
vnet1 primary-vsw0@primary network@0 00:14:4f:fb:2c:60
PEER MAC
primary-vsw0@primary 00:14:4f:a7:85:1e
vnet2@aplica_srss1 00:14:4f:fb:f4:e0
DISK
NAME VOLUME TOUT DEVICE SERVER
vdisk1 vol1@primary-vds0 disk@0 primary
VCONS
NAME SERVICE PORT
aplica_prod primary-vcc0@primary 5000
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME
aplica_srss1 bound ----- 5001 24 13184M
MAC
00:14:4f:fb:ad:fb
VCPU
VID PID UTIL STRAND
0 8 100%
1 9 100%
2 10 100%
3 11 100%
4 12 100%
5 13 100%
6 14 100%
7 15 100%
8 16 100%
9 17 100%
10 18 100%
11 19 100%
12 20 100%
13 21 100%
14 22 100%
15 23 100%
16 24 100%
17 25 100%
18 26 100%
19 27 100%
20 28 100%
21 29 100%
22 30 100%
23 31 100%
MEMORY
RA PA SIZE
0x8000000 0xc8000000 13184M
VARIABLES
auto-boot?=true
boot-device=
NETWORK
NAME SERVICE DEVICE MAC
vnet2 primary-vsw0@primary network@0 00:14:4f:fb:f4:e0
PEER MAC
primary-vsw0@primary 00:14:4f:a7:85:1e
vnet1@aplica_prod 00:14:4f:fb:2c:60
VCONS
NAME SERVICE PORT
aplica_srss1 primary-vcc0@primary 5001
Then i mount the ISO images of The solaris OS 5/08, Later install the jumpstart server without troubles.... Here are the Configuration files needed for the properly setup of the service for a better guide

# ./add_install_client -d -e 0:14:4f:fb:2c:60 -s Zolder:/var/jump_start/ sun4v
cleaning up preexisting install client "0:14:4f:fb:2c:60"
To disable 0:14:4f:fb:2c:60 in the DHCP server,
remove the entry with Client ID 0100144FFB2C60
To enable 0100144FFB2C60 in the DHCP server, ensure that
the following Sun vendor-specific options are defined
(SinstNM, SinstIP4, SinstPTH, SrootNM, SrootIP4,
SrootPTH, and optionally SbootURI, SjumpCF and SsysidCF),
and add a macro to the server named 0100144FFB2C60,
containing the following option values:
Install server (SinstNM) : Zolder
Install server IP (SinstIP4) : 172.24.0.10
Install server path (SinstPTH) : /var/jump_start/
Root server name (SrootNM) : Zolder
Root server IP (SrootIP4) : 172.24.0.10
Root server path (SrootPTH) : /mnt/s0/Solaris_10/Tools/Boot
Boot file (BootFile) : 0100144FFB2C60
# cat /etc/inet/hosts // The Content of this file is exactly with ipnodes file
127.0.0.1 localhost
172.24.0.10 Zolder loghost
172.24.0.9 primary-vsw0
172.24.0.8 aplica_prod
172.24.0.7 aplica_srss1
# cat /etc/ethers
00:14:4f:fb:2c:60 aplica_prod
# cat /etc/bootparams
aplica_prod root=Zolder:/mnt/s0/Solaris_10/Tools/Boot install=Zolder:/var/jump_start/ boottype=:in rootopts=:rsize=8192
# cat /etc/dfs/dfstab
share -F nfs -o ro,anon=0 /var/jump_start/
share -F nfs -o ro,anon=0 /mnt/s0/Solaris_10/Tools/Boot
share -F nfs -o ro,anon=0 /mnt/s1
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
vsw0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 172.24.0.10 netmask fffffe00 broadcast 172.24.1.255
ether 0:14:4f:a7:85:1e
vsw0:1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 172.24.0.9 netmask fffffe00 broadcast 172.24.1.255
Here i plumb up the networks interfaces and setup the vsw0 device and change the MAC address of the vsw0 for the same of the bge0 device.
Then i Log to a Guest LDOM aplica_prod
----------START CONSOLE 1-------------------------------
# telnet localhost 5000
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
Connecting to console "aplica_prod" in group "aplica_prod" ....
Press ~? for control options ..
----END CONSOLE 1----
At the same time i open another console for startup the Guest LDOM aplica_prod i make a snoop of the vsw0 interface
---START CONSOLE 2---
# ldm start aplica_prod
LDom aplica_prod started
-bash-3.00# snoop -d vsw0 | grep aplica_prod
Using device /dev/vsw0 (promiscuous mode)
---END CONSOLE 2-----
In the other console is produced the next exit
----START CONSOLE 1------
Sun Fire(TM) T1000, No Keyboard
Copyright 2008 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.28.9, 2048 MB memory available, Serial #66792544.
Ethernet address 0:14:4f:fb:2c:60, Host ID: 83fb2c60.
Boot device: File and args:
ERROR: boot-read fail
Evaluating:
Can't locate boot device
{0} ok boot vnet1 install
Boot device: /virtual-devices@100/channel-devices@200/network@0 File and args: install
Requesting Internet Address for 0:14:4f:fa:82:17
Requesting Internet Address for 0:14:4f:fa:82:17
Timed out waiting for TFTP reply
---END CONSOLE 1-----
in the console 2 the snoop generates an exit of the net traffic for the vsw0 device
----START CONSOLE 2--------
primary-vsw0 -> aplica_prod RARP R 0:14:4f:fb:2c:60 is 172.24.0.8, aplica_prod
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
primary-vsw0 -> aplica_prod RARP R 0:14:4f:fb:2c:60 is 172.24.0.8, aplica_prod
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
Zolder -> aplica_prod TFTP Error: access violation
aplica_prod -> BROADCAST TFTP Read "AC180008" (octet)
----END CONSOLE 2----
Once start the snoop to produce messages make a ping to the IP's that should be assigned in the host file and all give a succesful answer BUT without start the Solaris 10 Instalation
# ping 172.24.0.8
172.24.0.8 is alive
# ping 172.24.0.9
172.24.0.9 is alive
# ping 172.24.0.10
172.24.0.10 is alive
I really need help with this trouble ..and any help or advice will be thrully appreciated
Thanks
PD: any other required configuration file will be provided if is needed

Moving disks while maintaining Solaris 10 install from one v240 to another.

Hi,
I want to move a Solaris 10 install from a sunfire v240
with a single cpu to another sunfire v240 with dual cpu's. Here are the
details of the hosts as well as configuration.
I have 2 sunfire v240's. One has a single 1 Ghz cpu and the second has
dual 1.5 Ghz cpu. I want to move the disks of the single cpu host to
the host with dual cpu's. I want to keep the installed version of
Solaris 10 intact. The installation of Solaris is split across 2
mirrored disks, i.e. 4 disks in total. I am using Suns volume manager
for mirroring and also have one files system mirrored with zfs.
The questions I have are the following:
1) Can I simply shut down the servers and swap the disks to the
destination host, in the same disk slots? The controllers the disks are
on line up and are the same between the 2 hosts.
2) Will the kernel pickup the changes moving from a single 1 Ghz cpu to
dual 1.5. Ghz cpu's with out any problems? Will the kernel pickup the
faster cpu's speeds. i.e. will it know it is now running dual 1.5. Ghz
cpu opposed to a single 1 Ghz?
3) Would we have to break the mirroring on the OS before shutting it
down?
4) As another option, instead of swapping disks, could we swap the
cpus? Move the dual 1.5. Ghz cpu's to the other host? Will the
motherboards read the updates of the cpu or are their jumper settings we
would need to update?
Thanks for your help.

Box A
Sparc Solaris 9, Oracle 10g
Box B
Solaris 10 x86, Oracle 11g
I know there are many factors, but I'm pretty new to both unix & oracle, so I >needed some general steps to get me started. You have many options.
Since you're in 10g, Have the Target Database created in Solaris 10 x86, Oracle 11g.
you can use,
RMAN - Cross platform Transportable Tablespaces.
Datapump Export and Datapump import.
Read the following:
How To Use RMAN CONVERT DATABASE for Cross Platform Migration - 413586.1
http://download-uk.oracle.com/docs/cd/B19306_01/backup.102/b14191/dbxptrn.htm
http://www.oracle-base.com/articles/10g/OracleDataPump10g.php
http://www.oracle-base.com/articles/10g/RMANEnhancements10g.php#cross_platform_tablespace_conversion

Solaris 10 Install Hangs at 15% on my HP DL 585?

Solaris 10 Install Hangs at 15% on my HP DL 585
I have taken out all the additional extra cards so I am left with the basic box, it has been configured to run in Raid 1 so my four disks become two.
I can still get it to bring up a shell and do other things, but the installer just appears not to want to go pass 15%
Help?

Which version of Solaris and how much memory do you have in the system.

Minimize and maximize Solaris 10 installed on VM virtual Box.

How can I minimize and maximize Solaris 10 installed on VM virtual Box.
Thanks
Paulo

Solaris is working just fine. Everything is ok. now since I open Solaris via VM Virtual box, the Solaris main page fills only half of the monitor. I can minimize/maximize the Virtual Box. But Solaris dimensions are fix and doesn't change. This leaves me a little room to open applications on Solaris. I had the same problems with my Ubuntu, by installing adds-on it was fixed. For Solaris I installed Guest additions, didnt help.
Thanks
Paulo

Netra 240 Key switch position chnage to UNKNOWN

I cannot boot up NETRA 240 , the key switch position is change to UNKNOWN even if the rotary switch is set up to NORMAL position!
I boot up the NETRA in using bootmode option skip_diag but after a while the system goes down and I cannot boot up after!
SEP 21 02:31:51 spatialnetra9: 00040076: "Keyswitch position has been changed to UNKNOWN."
SEP 21 02:50:33 spatialnetra9: 00060000: "SC Login: User admin Logged on."
SEP 21 04:02:30 spatialnetra9: 0004000a: "SC set bootmode to skip_diag, will expire THU SEP 21 04:12:30 UTC 2006."
SEP 21 04:02:42 spatialnetra9: 00040001: "SC Request to Power On Host."

Unfortunately, we do not use netmgt port (it is disconnected).
Even though, I can not use login and pass info in script (security reasons).

Adding packages from solaris 8 install disks

I need Solaris Make for Solaris 8. I have installed Solaris 8 off of downloaded Solaris 8 install disks. I apparently forgot to include Solaris Make in the install and now need to add it. When I copy the pkg SUNWxcu4t (the pkg for make and scc) and pkgadd it it claims installation is sucessful but still I have no make. It is supposed to install to /usr but there is no make there.
What am I doing wrong?
Thanks

Ok I have all of my compilling isuse resolved!
Just in case anyone else browsing this forum has the same problems here is what I have learned:
These are the relevent Packages:
for tools (ar, sccs, lex, yacc, make, nm, truss, ld, as)
SUNWbtool, SUNWsprot, SUNWtoo
for libraries & headers:
SUNWhea, SUNWarc, SUNWlibm, SUNWlibms
SUNWdfbh, SUNWcg6h
for ucb compat:
SUNWsra, SUNWsrh
You definatly need to use Solaris make (found in SUNWsprot), Solaris ar (found in SUNWbtool),
gnu tar, and gnu cc both from sunfreeware.com (I love pkg-get ^_^)
either add /opt/sfw/bin/ to your path or put a dynamic link for gcc into /usr/local/bin/ I prefer the latter.
and add /usr/ccs/bin/ to your path permanently.
Thanks for your help every one.

Please, solaris 10 installed in my X86 computer, but do not recognize NIC

Even I get a sun NIC, I do not know hot to install driver. So I am wondering, if I install a Sun PCI NIC, does the
solaris 10 recognize the sun PCI NIC automatically? If solaris can install NIC driver by itself, I will not install NIC driver, thanks

A number of drivers for supported cards were installed by default.
Solaris will not take any additional action when you add hardware. Either you've already got the driver and it'll be recognized, or you don't. If you don't have the driver, there might be a third-party driver available that you can download and install.
Best course of action is to add devices that are on the hardware compatibility list.
Darren

Solaris 10 on Netra T1 install issues....

I have gentoo installed on my netraT1 (which is apparently in the sun4u Platform Group) it has a 500mhz UltraSparc IIe processor and 1Gig of RAM.
I decided to try solaris 10 so I downloaded all the cd images to my winows machine and used nero to burn them all. I put the first one in and typed boot cdrom and got a panic:
ok boot cdrom
Boot device: /pci@1f,0/pci@1,1/ide@d/cdrom@0,0:f File and args:
Short read. 0x0 chars read
krtld: error during initial load/link phase
panic - boot: exitto64 returned from client program
Program terminated
Ok
Here is some more info:
ok probe-scsi
Target 0
Unit 0 Disk SEAGATE ST318305LSUN18G 0340
Target 1
Unit 0 Disk SEAGATE ST34371W SUN4.2G7462
Firmware CORE Release 1.0.12 created 2002/1/8 13:0
Release 4.0 Version 12 created 2002/01/08 13:01
cPOST version 1.0.12 created 2002/1/8
CORE 1.0.12 2002/01/08 13:00
Is there anything I could do to get this install to work? This is my only sun machine so I dont think I could get netbooting to work. I tried burning the first cd 2 times just to make sure it wasnt my burner and it still was getting the same errors ;(
Thanks,
Ryan

I have no really good answer here..
I guess you are using a Netra T1 AC200, right?
Some futher questions;
Are you using an internal CD-Rom?
Have you tried the CD-Rom before so you know it works?
What happens if you try "boot cdrom" without inserting any CD? I think the bootpath to the cd-rom looks a bit strange, and testing that would be the easiest way of verifying if its correct or not. If the path is correct you should get a different error if you attemt to boot from a non-existing CD.
Last question; which Solaris 10 version did you download?
7/M.

Attempting to install Solaris 10 on Netra t1 via external DVD-Rom

Hello Experts,
I am trying to install Solaris 10 on my Netra t1 via external DVD. I connected the DVD-ROM to the scsi port on the back. System recognized the DVD but does not allow me to boot from it. I have done many things without any success. Following are the details:
System info:
Netra t1 (UltraSPARC-IIi 440MHz), No Keyboard
OpenBoot 3.10.25 ME, 1024 MB memory installed,
Ran the scsi test and it doesn't report any issues:
ok test scsi
Probe-scsi-all shows the drive:
ok probe-scsi-all
/pci@1f,0/pci@1,1/scsi@2
Target 0
Unit 0 Disk SEAGATE ST318404LSUN18G 4207
Target 1
Unit 0 Disk SEAGATE ST318404LSUN18G 4207
Target 4
Unit 0 Removable Read Only device TOSHIBA DVD-ROM SD-M14011009
devalias also shows as cdrom1:
ok devalias
cdrom1 /pci@1f,0/pci@1,1/scsi@2/disk@6,0:f
cdrom /pci@1f,0/pci@1/pci@1/ide@e/cdrom@2:f
ide-disk /pci@1f,0/pci@1/pci@1/ide@e/disk@0:f
ide-cdrom /pci@1f,0/pci@1/pci@1/ide@e/cdrom@2:f
ide /pci@1f,0/pci@1/pci@1/ide@e
I created devalias manually also with no help. Following is what I get when I try to boot from it:
ok boot cdrom1
Resetting ...
Netra t1 (UltraSPARC-IIi 440MHz), No Keyboard
OpenBoot 3.10.25 ME, 1024 MB memory installed,
Executing last command: boot cdrom1
Boot device: /pci@1f,0/pci@1,1/scsi@2/disk@6,0:f File and args:
Drive not ready
Evaluating: boot cdrom1
Can't open boot device
I verified the DVD and it works just fine. I install the OS with the same DVD on Netra-440 system without any issues.
Please tell me what am I missing here or doing wrong. Please help.

Sun-worshiper,
Thank you so much for pointing that out. I was loosing it.
Just in case someone else runs into this type of issue:
When you run probe-scsi-all please pay attention to the target. In order to boot from the DVD, I executed the following commands from the ok prompt:
ok nvalias dvd /pci@1f,0/pci@1,1/scsi@2/disk@4,0:f
ok boot dvd

Installing solaris 10 on netra t1 105

im need to sun computer system....i have got to the point of hyperterm lom> and booting the system, but it has no software installed.. im trying to install solaris on a sun netra t1 105 256 mb ram and 19gb hd and NO CDROM im trying to "network install" from a windows 2003 server.. is this possibly or do i have to a sun workstation to install as boot/install server... or could i connect the hard drive to a windows 2003 server and format and install solaris on it using virual pc.... i haveit networked to my wireless router as well a x86 computer...
Edited by: lebaronman on Feb 28, 2008 2:01 AM

I have no really good answer here..
I guess you are using a Netra T1 AC200, right?
Some futher questions;
Are you using an internal CD-Rom?
Have you tried the CD-Rom before so you know it works?
What happens if you try "boot cdrom" without inserting any CD? I think the bootpath to the cd-rom looks a bit strange, and testing that would be the easiest way of verifying if its correct or not. If the path is correct you should get a different error if you attemt to boot from a non-existing CD.
Last question; which Solaris 10 version did you download?
7/M.

SCSI warnings - Solaris 10 Install - Netra 240

Similar Messages

Maybe you are looking for