SCXI 1520 quarter bridge setup will not output excitation voltage, but full bridge will

My SCXI system will not output an excitation voltage to the quarter bridge(verified with voltmeter). It works for a full bridge setup. When connected to a 'quarter bridge I' configuration, I can use MAX to null and shunt calibrate. The quarter bridge circuit appears to be balanced after the calibration, but the calibration results post a software gain factor close to zero, as well as a close to zero excitation voltage (eventhough I have the voltage configured for 5 volts). I have the SCXI 1520 module, the virtual channels, and the wiring properly configured (several years experience with this device). I'm using an old E series DAQ card AI-16XE-50, with the 50 pin cable that plugs in the back of the SCXI chassis. I noticed I had two bent pins with the cable connector module that plugs into the SCXI backplane. I was able to straighten them, so the cable connects properly, but I suspect the bent pin incident caused electrical circuit damage. Any suggestions on trouble shooting? None of the three 1520 modules I have will output an excitation voltage for a quarter bridge.

Sorry that I don't have an answer for you tyea, but I'm interested in your thread because I have a similar issue with a 1520. My excitation votltage, as measured with a DVM, is always 1V. I've tried 0V, 1V, 5V --- it's always 1V, on Full or Quarter bridge. I'm using a similar DAQ to yours - a PCI 16XE-10 (and a PCI-6030E on antother system).
I don't have a lot of experience with these modules. This could be a wiring or programmatic thing I'm doing wrong.
Richard

Similar Messages

Blend will not read my PC but my PC will read the Classic

On my Classic the only page I gave when I open Blend is:
Blackberry Blend
Open Device Connection Page
I can read the Claccic from the PC but not the phine to the PC

Are you trying to view files on your PC via the File Manager application?
Did someone help you? Click Like! Did a post solve your issue? Click Accept as Solution!

Firefox will not load any web page, other programs will. Continuously "connecting"

Firefox will not load any pages, but Google Chrome will. Firefox will 'load' the home page, but with any other site, the tab will continuously circle and say "connecting". I have tried clearing my cache, starting in safe mode, and restarting my computer. So far, nothing is working.

Update..when I open firefox from scratch, the main firefox pages on the home page seem to work. But as soon as I try to go anywhere else, IE going to a website in the address bar or even trying to access the defauly bookmark links, it just sits there loading but never brings anything up.

Final cut 10.1 will not output or input thru Blackmagic intensity shuttle thunderbolt on 2013 Retina MBP while Premere Cs6 does

Final Cut 10.1 will not output or input thru Blackmagic intensity shuttle thunderbolt on 2013 Retina MBP while Premere Cs6 does

As I mentioned, Premere Cs6 has no issues with the BM Intensity Shuttle Thunderbolt. This proves that the Mac sees the shuttle. iMovie, like FCPX 10.1 does not see it. Not sure if this is an Apple issue or a BlackMagic issue. I plan to contact BlackMagic on Monday out of curiosity. This issue is more of a surprise than a dead end. Happily there are easy workarounds for capture. I use the BlackMagic software to capture. My main issue seems to be that I am unable to use FCPX to output through the Shuttle. Fortunately I have a Mac Pro and an older BlackMagic card which has worked. It is so very nice to skim video on an SSD. No lag and no wear and tear on a mechanical hard drive. The 1Tb Apple SSD is shockingly fast. It is a new world.

I upgraded from PS5 to PS 6 and Bridge will not open in RAW, AMT Failure, also will let me update

I upgraded from PS5 to PS 6 and Bridge will not open in RAW, AMT Failure, also will not let me update and closes Bridge down.
I have uninstalled and reinstalled 3 times and still no success. Any suggestions?

What system are you on? Did you run the Creative Suite Cleaner Tool inbetween your install attempts? If not, try that to produce a "clean" install with factory defaults. Other than that there could be some specific system issues at play, but again, we'd need to actually know what system you are on...
Mylenium

I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you plea

I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you please advise?

You may need many other updates to retain compatibility with Lion. I suggest you reinstall Snow Leopard. Unfortunately, you will need to erase the drive first. Be sure to backup your data if you haven't done so already.
Clean Install of Snow Leopard
Be sure to make a backup first because the following procedure will erase
the drive and everything on it.
     1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
         with your computer. Insert the disc into the optical drive and restart the computer.
         After the chime press and hold down the "C" key. Release the key when you see
         a small spinning gear appear below the dark gray Apple logo.
     2. After the installer loads select your language and click on the Continue
         button. When the menu bar appears select Disk Utility from the Utilities menu.
         After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
         size.) Click on the Partition tab in the DU main window. Set the number of
         partitions to one (1) from the Partitions drop down menu, click on Options button
         and select GUID, click on OK, then set the format type to MacOS Extended
         (Journaled, if supported), then click on the Apply button.
     3. When the formatting has completed quit DU and return to the installer. Proceed
         with the OS X installation and follow the directions included with the installer.
     4. When the installation has completed your computer will Restart into the Setup
         Assistant. After you finish Setup Assistant will complete the installation after which
         you will be running a fresh install of OS X. You can now begin the update process
         by opening Software Update and installing all recommended updates to bring your
         installation current.
Download and install Mac OS X 10.6.8 Update Combo v1.1.

Hello I have 2 seperate airport express systems on my network, each connecting to a stereo in a different room. suddenly, the one in the living room will not stop flashing amber, but the one in the bedroom works fine. I have already tried resetting it

Hello
I have 2 seperate airport express systems on my network, each connecting to a stereo in a different room. suddenly, the one in the living room will not stop flashing amber, but the one in the bedroom works fine. I have already tried resetting it with a pin, resetting it while plugging it in, and trying to find it in airport express setup (the setup assistant can't find it at all).
What am i doing wrong?

How do I configure the AX to connect to the hub's wireless network? It will only scan one base station Airport Express at a time in the Airport Utility. I think what I am trying to do is use the hub as a router to the two AX's. Is there a specific way to set this up?
To set up the AX to join a wireless network as a "Wireless Client," using the AirPort Utility, either connect to the AX's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, try these settings:
Launch the AirPort Utility.
Select the AX.
If not already connected to the AX's wireless network, go ahead and switch to it when prompted.
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <type in the network name/SSID of the wireless network that you want to join or select it from the pop-up menu>
Wireless Security: None OR, if you are using security on your wireless network:
Wireless Security: <Select the appropriate level of security for the existing wireless network: WPA/WPA2 Personal | WPA2 Personal>
Password: <enter your wireless network security password>
Verify Password: <re-enter the same security password>
Click Update to write the new settings to the AX.

HP LaserJet 1536dnf MFP will not copy or scan but does print

My HP LaserJet 1536dnf MFP will not copy or scan but does print. It does not matter if I use the ADF or the glass. When copying or scanning I get a completey black page. The light bar does move from one end of the printer glass to the other. There are no connectivity issues as the printing function and the e-print function work fine.
Thank you for your help

Hi @akb3,
I understand that when you try to scan or copy, you are getting a black page. I can help you with this.
Please keep the scanner lid open and then press the copy button.
Check if the scanner bulb glows.
Check if the scanner moves freely across the glass.
If it does not try connecting the printer directly to the wall jack and try again.
Update the printer's firmware if the bulb glows and scanner moves freely. HP LaserJet Pro M1536dnf Multifunction Printer Drivers.
If the issue persists, then I would recommend to call HP Tech Support for further assistance to see what other options are available for you at 800-474-6836. If you live outside the US/Canada Region please click the link below to get the support number for your region. Contact HP Worldwide.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

All the CD's I have imported will not play. The only music that will play is cd's I have purchased from itunes. How can I get all my albums to play, please??

All the CD's I have imported will not play. The only music that will play is cd's I have purchased from itunes. How can I get all my albums to play, please??

iTunes Store- Transferring purchases from iOS device or iPod to a computer
Downloading past purchases from the App Store, iBookstore, and iTunes Store
How to dowload purchased music

My ipod touch 5th gen will not connect to itunes, but my computer registers my ipod. i have tried placing my ipod in recovery mode, uninstalled and reinstalled itunes, and restarted my laptop but my ipod will not connect to my itunes..... help ._.

My ipod touch 5th gen will not connect to itunes, but my computer registers my ipod. i have tried placing my ipod in recovery mode, uninstalled and reinstalled itunes, and restarted my laptop but my ipod will not connect to my itunes..... help ._.

Try
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
or
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
Before you reinstall the Apple software, also remove iCloud vi Control Panel Remove programs. The reinstall the Apple programs
New cable and different USB port?
Runs this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
Try on another computer to help determine if computer or iPod problem

Javascript will not open in mozllia but it will open in internet explorer

Java script is enabled in Mozilla options. When I try to open an item with script it will not open in Mozilla.but when I try to access the same item it will open Internet Explorer

No problems here to open the login page.<br />
It is a frameset with the second frame being the login form: https://www.ingdirect.com.au/client/Login.aspx
* "Clear the Cache": Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
* "Remove the Cookies" from sites that cause problems: Tools > Options > Privacy > Cookies: "Show Cookies"
Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]

Ibookg4 will not go past the grey screen and will not accept a disc

my ibook will not go past the grey screen and will not accept a disc

Have you tried starting up in Safe Mode? If not, I suggest that you give it a try. This will take quite awhile longer than a normal startup because it does a file check and repair of the hard disk.
If this works you will see your normal desktop. Once completely started up in Safe Mode, try to restart normally, and go to Applications > Utilities > Disk Utility. Click on the top hard drive icon in the left sidebar and note the S.M.A.R.T. status at the bottom right of the pane. What does it say?
Select the named boot volume in the left sidebar, ("Macintosh HD" unless you've renamed it). What is the hard drive capacity and how much space remains available on it? Repair permissions on it.
See if you are able to do a little hard drive maintenance to help things out.

Farmville will not load using Firefox, but it will with IE, for over a week now.

Farmville will not load using Firefox, but it will with IE, for over a week now. I have cleared the cache and cookies multiple times, updated flash player, did a virus and malware scan, allowed java script, allowed mozilla in the Windows firewall, contacted Zynga multiple times, and yet Farmville still will not load using Firefox, my main and preferred browser. I'm very frustrated and want this fixed.

Thanks for the advice cor-el, but if you would read the info I posted, I already did that, SEVERAL TIMES. That's not the solution unfortunately.

Using Lion, recent Movies with .mov extension will not play in Quicktime, but earlier ones taken with same camera (Kodak M530) will play fine.

Using Lion, recent Movies with .mov extension will not play in Quicktime, but earlier ones taken with same camera (Kodak M530) will play fine. I have got VLC which runs them fine but cannot get movies saved in iPhoto to play in VLC...and of course its a real bugger to copy moves from iPhoto to another folder; in fact if anyone can tell me how to do that I will accept defeat!

Hello Shad:
Have you downloaded and installed Flip4Mac?
http://www.microsoft.com/mac/otherproducts/otherproducts.aspx?pid=windowsmedia
Barry

Pandora will not play in Firefox, but it will play in Chrome and IE.

Pandora will not play in Firefox, but it will play in Chrome and IE. In Firefox, it loads the initial Pandora page, which just says Pandora. In Chrome and IE, it then loads the player automatically. In Firefox it just sits there on the initial page that just says "Pandora," and it never loads the player. My Flash Player is updated, and I cleared all the caches... not sure what the problem is. Can anyone help?

Is your version of Firefox the latest one?

SCXI 1520 quarter bridge setup will not output excitation voltage, but full bridge will

Similar Messages

Maybe you are looking for