SD card detected but not assigned a device

I have a Dell XPS 14 notebook which comes with a SD card slot. I plug in my SanDisk 8GB card from my camera and the following shows up in dmesg:
[821605.639247] mmc1: cannot verify signal voltage switch
[821605.750637] mmc1: new ultra high speed SDR50 SDHC card at address e624
And that's it. The card is not assigned to any device. lsmod seems to indicate that I have the required modules loaded:
± % lsmod | egrep 'mmc|sdhci|sd'
sd_mod 31361 3
rtsx_pci_sdmmc 13911 0
scsi_mod 132250 4 usb_storage,libata,sd_mod,sr_mod
sdhci_pci 12604 0
sdhci 28820 1 sdhci_pci
mmc_core 95465 3 sdhci,rtsx_pci_sdmmc,sdhci_pci
rtsx_pci 32305 2 rtsx_pci_ms,rtsx_pci_sdmmc
lspci also shows the SD card controller:
03:00.1 SD Host controller: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01)
But fdisk -l just shows my hard drive
± % fdisk -l
Disk /dev/sda: 465.8 GiB, 500107862016 bytes, 976773168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disklabel type: gpt
Disk identifier: 0FBC37E2-A97E-4040-996C-F290C0C9CF0A
Device Start End Size Type
/dev/sda1 2048 1050623 512M EFI System
/dev/sda2 1050624 976773134 465.3G Linux filesystem
Anything else I need to do to get the SD card assigned to a device so I can mount it.

It's considered a removable drive. I have a USB card reader that if I insert it after the computer has been booted it gives me a little trouble, but having it inserted on booting it wants to put the device in a different order.

Similar Messages

TS3694 iOS: Device detected but not identified properly on iTunes for Windows error 54

iOS: Device detected but not identified properly on iTunes for Windows error 54 my iPhone 4s ois 7.1.2 my pc is windows 8.1 my iTunes ver 11.3.1.2. I cant sync with itunes

Look in your Pictures folder and delete the iPhone Photo Cache.

IPod Nano 6th Gen detected but not recognized

Since recently, my IPod is not being recognized by iTunes (11.1.4.62 ). The error says that it is detected but not be identified properly. I went through all the troubleshooting steps including resetting my ipod, re-starting the driver, re-installing iTunes but nothing works. Interestingly, if iTunes is not open, I can see the iPod as a storage device, I can open and browse it. So I assume there is no error with the wire, the iPod itself or the driver. As soon as iTunes gives the above error, it stops being visible as a storage device. How can I fix this?

Aridra,
Thanks very much for this - I had exactly the same problem; went through the same steps to no avail unitl I read your post. Similarly, I uninstalled EVERYTHING Apple on my PC and re-installed. Bingo !! my iPod is now recognised and synched.

Works on emulators but not on mobile devices

Hello,
My project works on emulators but not on mobile devices (no image and on Samsung it says "unsupported file").
Please help, I don't know what to do. My configurations: MIDP 2.1, CLDC 1.1.
Thanks in advance.
Edited by: Vitali.pom on Oct 27, 2011 12:01 PM

Edit: I succeeded to solve it accidentally. I did the following: Sign the jar in Netbeans, clean and build, the jar didn't work, I wiped out the .ks from the jar and clean and build again. Now it worked.
Edited by: Vitali.pom on Oct 30, 2011 1:28 AM

What would happen if I turn off my backup and delete backup data From my device? Will it delete my music and everything for ever or just stay in the cloud but not on my device?

What would happen if I turn off my backup and delete backup data From my device? Will it delete my music and everything for ever or just stay in the cloud but not on my device?

If you have multiple devices backing up to the Cloud, you will see all of them listed. You would click on each device to change what is backed up from that device. You can then delete your individual back-ups.
Once you have all your settings to your liking, you can then go back to Settings>iCloud>Storage & Backup, and click on Back Up Now (bottom of the screen) to create a fresh backup with your new settings.
Cheers,
GB

When i plug in my ipod nano (6th generation) a message comes up saying it's 'detected but not identified' i've spend like all day trying to solve it, uninstalled it, reinstalled it and nothing seems to work..

when i plug in my ipod nano (6th generation) a message on itunes saying the ipod is 'detected but not identified'- i've spent all day trying to fix it and nothing seems to work so i can't sync any songs..

Hello beafraser,
Here's an article to help troubleshoot when your iPod is detected but not identified.
iPod nano: Error message saying that iPod 'could not be identified properly'
http://support.apple.com/kb/ts3218
Hope that helps.
Thank you for visiting Apple Support Communities.
Nubz

HT2534 How to connect to iTunes apps, I do not, in July to conduct a credit card number, but not the button none..

How to connect to iTunes apps, I do not, in July to conduct a credit card number, but not the button

Follow the steps in this article EXACTLY:
http://support.apple.com/kb/ht2534

IPhone Detected But Not Identified?

I hooked up my iPhone to my base that goes into my cpu and I got this message: "An iPhones was detected, but could not be identified properly. Please disconnect and reconnect the iPhone and try again." I havent had any problems like this before. Will a reinstall over this iTunes fix the problem? I am running Windows XP. I have also noticed that when I plug up my phone, the Scanner and Camera Wizard pops up recognizing the iPhone as a camera. Also when running iTunes after I got that message, my cpu will freeze for about 5 seconds and work fine a little while then freeze again for 5 seconds. But when I close iTunes, it stops freezing.

I am having the same issue iPhone detected, but not identified. Did you get a solution to the problem? Had to go to th Apple store to register my phone. iPhone connected fine with their MacBook. That doesn't help me at home though.

What do you do when ipod is detected but not identified?

What do you do when ipod is detected but not identified?

Hi there schnee2,
You may find the troubleshooting steps in the article below helpful.
iPod not recognized in My Computer and in iTunes for Windows
http://support.apple.com/kb/ts1369
-Griff W.

Webcam detected but not enumerated. Logitec cam, JMF, GNU/Linux, v4l2

Hi,
I've been trying the whole day to get my "Logitech, Inc. QuickCam for DELL Notebooks" with Java Media Framework.
From searching the web and mainly the sun forums I kind of understand that JMF is not getting much attention from the developers.
Maybe I'm wrong. (I hope so)
I need to use something to capture video from a webcam on linux using java.
JMF uses v4l but, as the v4l people say on their site, v4l2 support of v4l is broken...
I downloaded the jmf-2_1_1e-linux-i586.bin, tried to run the programs, they run but the webcam is not listed for capture.
When I search for devices the program outputs: (jmfinit or the others from jmf package)
JavaSound Capture Supported = true
JavaSoundAuto: Committed ok
Name = v4l:UVC Camera (046d:08c6):0
Trying 4 320 240
Trying 15 768 576
java.lang.Error: Can't open video card 1
java.lang.Error: Can't open video card 9
Apparently the camera is detected but something else prevents it from being used.
I would say the v4l interface...
I can view correctly the output from my webcam using:
mplayer -fps 30 -tv driver=v4l2:width=640:height=480:device=/dev/video0 tv://
but if I change driver=v4l2 to driver=v4l it wont work anymore...
Is there a workaround? Am I missing something? because a few people were able to use it so why not me =)

nanom wrote:
I know I am resurrecting an old thread but I would like to have a solution on this topic and notice that colector may have one base on another thread, where I wrote but the thread was locked.
Please before locking this tread can you please facilitate me colector's mail or some way to contact him?If his email address is not public in his profile you cannot contact him directly.
As you have been told once already, please start your own thread. Locking this thread.

Image Capture connects to card reader but not camera

Image Capture and iPhoto do not detect new connected Canon camera. Will read card via card reader. Camera will connect to older macbook iPhoto and Image Capture but not my iMac. Image Capture in Mountain Lion has no perferences anymore. Tried Repairing Disk Permissions but no success. Any ideas?

Sorry, there is no setting on the AirPort Extreme card built-in your new iMac that can be tweaked to "force" a connection to the Netgear's "n" network.
Does your Netgear allow for different Network Names (or SSIDs) for each of its radios? If so, you can try an experiment by renaming the 5 GHz radio's Network Name, and then, specifically connect the iMac to it.
Also, since "n" can operate on either radio, it appears that your iMac is "locking" on the 2.4 GHz radio. Does your iMac have any trouble connecting to any other "n" Wi-Fis? If so, then there may be a problem with either the AirPort Extreme card or the internal antennae on the iMac ... and it would warrant a visit to your local Apple Store to have them take a look.

EGalax Touchscreen Detected But Not Working

I installed Arch Linux x64 in Lenovo S400 Touch, it has a "eGalax Inc. eGalaxTouch" Thouchscreen, i have tried most of the thread, yet i cant figure out how to get it to work!
Here is the output from lsusb
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 04f2:b420 Chicony Electronics Co., Ltd
Bus 001 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. RTS5129 Card Reader Controller
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 002: ID 0eef:a107 D-WAV Scientific Co., Ltd
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Here is the output from Xorg Log
[ 33.081] (II) config/udev: Adding input device eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00 (/dev/input/event5)
[ 33.081] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Applying InputClass "evdev touchscreen catchall"
[ 33.133] (II) systemd-logind: got fd for /dev/input/event5 13:69 fd 15 paused 0
[ 33.134] (II) Using input driver 'evdev' for 'eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00'
[ 33.134] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: always reports core events
[ 33.134] (**) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Device: "/dev/input/event5"
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Vendor 0xeef Product 0xa107
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found absolute axes
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found absolute multitouch axes
[ 33.134] (II) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: No buttons found, faking one.
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found x and y absolute axes
[ 33.134] (--) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Found absolute touchscreen
[ 33.134] (II) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: Configuring as touchscreen
[ 33.134] (**) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: YAxisMapping: buttons 4 and 5
[ 33.134] (**) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 33.134] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.0/0003:0EEF:A107.0001/input/input6/event5"
[ 33.134] (II) XINPUT: Adding extended input device "eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00" (type: TOUCHSCREEN, id 9)
[ 33.134] (II) evdev: eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: initialized for absolute axes.
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) keeping acceleration scheme 1
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) acceleration profile 0
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) acceleration factor: 2.000
[ 33.135] (**) eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00: (accel) acceleration threshold: 4
[ 33.135] (II) config/udev: Adding input device eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00 (/dev/input/mouse0)
[ 33.135] (II) No input driver specified, ignoring this device.
[ 33.135] (II) This device may have been added with another device file.
[ 33.136] (II) config/udev: Adding input device Lenovo EasyCamera (/dev/input/event12)
[ 33.136] (**) Lenovo EasyCamera: Applying InputClass "evdev keyboard catchall"
[ 33.136] (**) Lenovo EasyCamera: Applying InputClass "system-keyboard"
[ 33.137] (II) systemd-logind: got fd for /dev/input/event12 13:76 fd 16 paused 0
[ 33.137] (II) Using input driver 'evdev' for 'Lenovo EasyCamera'
Here is the output from xinput --list
xinput --list
⎡ Virtual core pointer id=2 [master pointer (3)]
⎜ ↳ Virtual core XTEST pointer id=4 [slave pointer (2)]
⎜ ↳ eGalax Inc. eGalaxTouch EXC7910-1018-08.00.00 id=9 [slave pointer (2)]
⎜ ↳ SynPS/2 Synaptics TouchPad id=13 [slave pointer (2)]
⎣ Virtual core keyboard id=3 [master keyboard (2)]
↳ Virtual core XTEST keyboard id=5 [slave keyboard (3)]
↳ Power Button id=6 [slave keyboard (3)]
↳ Video Bus id=7 [slave keyboard (3)]
↳ Power Button id=8 [slave keyboard (3)]
↳ Lenovo EasyCamera id=10 [slave keyboard (3)]
↳ Ideapad extra buttons id=11 [slave keyboard (3)]
↳ AT Translated Set 2 keyboard id=12 [slave keyboard (3)]
Here is the output from xrandr
Screen 0: minimum 8 x 8, current 1366 x 768, maximum 32767 x 32767
LVDS1 connected primary 1366x768+0+0 (normal left inverted right x axis y axis) 309mm x 173mm
1366x768 60.10*+
1024x768 60.00
800x600 60.32 56.25
640x480 59.94
DP1 disconnected (normal left inverted right x axis y axis)
HDMI1 disconnected (normal left inverted right x axis y axis)
VGA1 disconnected (normal left inverted right x axis y axis)
VIRTUAL1 disconnected (normal left inverted right x axis y axis)
Here is the output of lsmod
Module Size Used by
fuse 87590 3
ctr 12927 2
ccm 17534 2
coretemp 12820 0
hwmon 12930 1 coretemp
intel_rapl 17605 0
iosf_mbi 12682 1 intel_rapl
arc4 12536 2
brcmsmac 536435 0
cordic 12352 1 brcmsmac
brcmutil 13136 1 brcmsmac
b43 414640 0
mac80211 648753 2 b43,brcmsmac
x86_pkg_temp_thermal 12951 0
intel_powerclamp 17122 0
cfg80211 476584 3 b43,brcmsmac,mac80211
kvm_intel 143417 0
uvcvideo 84822 0
snd_hda_codec_hdmi 49263 1
ssb 65506 1 b43
rng_core 12808 1 b43
videobuf2_vmalloc 13286 1 uvcvideo
videobuf2_memops 12519 1 videobuf2_vmalloc
videobuf2_core 39635 1 uvcvideo
pcmcia 53108 2 b43,ssb
v4l2_common 12814 1 videobuf2_core
videodev 135040 3 uvcvideo,v4l2_common,videobuf2_core
pcmcia_core 18431 1 pcmcia
media 18365 2 uvcvideo,videodev
joydev 17063 0
snd_hda_codec_realtek 67322 1
snd_hda_codec_generic 63161 1 snd_hda_codec_realtek
rtsx_usb_ms 16899 0
memstick 13696 1 rtsx_usb_ms
bcma 46203 3 b43,brcmsmac
mousedev 17272 0
r8169 76869 0
kvm 435299 1 kvm_intel
mii 12675 1 r8169
iTCO_wdt 12831 0
iTCO_vendor_support 12649 1 iTCO_wdt
crct10dif_pclmul 13394 0
crc32_pclmul 12915 0
shpchp 35210 0
snd_hda_intel 26387 3
snd_hda_controller 26857 1 snd_hda_intel
ideapad_laptop 17447 0
snd_hda_codec 112621 5 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
ac 12715 0
crc32c_intel 21809 0
psmouse 107442 0
snd_hwdep 17244 1 snd_hda_codec
snd_pcm 88779 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_hda_controller
snd_timer 26614 1 snd_pcm
snd 73436 14 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel
ghash_clmulni_intel 12978 0
thermal 17559 0
cryptd 18553 1 ghash_clmulni_intel
pcspkr 12595 0
serio_raw 12849 0
battery 17452 0
mei_me 17987 0
mei 75468 1 mei_me
soundcore 13031 2 snd,snd_hda_codec
sparse_keymap 12818 1 ideapad_laptop
rfkill 18867 3 cfg80211,ideapad_laptop
i2c_i801 16965 0
evdev 21544 13
lpc_ich 20768 0
mac_hid 12633 0
processor 27777 0
sch_fq_codel 17343 6
ext4 514390 1
crc16 12343 1 ext4
mbcache 17171 1 ext4
jbd2 86379 1 ext4
rtsx_usb_sdmmc 25280 0
led_class 12855 3 b43,brcmsmac,rtsx_usb_sdmmc
mmc_core 110613 3 b43,ssb,rtsx_usb_sdmmc
rtsx_usb 17487 2 rtsx_usb_sdmmc,rtsx_usb_ms
hid_multitouch 17057 0
usbhid 48596 0
hid 110513 2 hid_multitouch,usbhid
sd_mod 43575 2
atkbd 22254 0
libps2 12739 2 atkbd,psmouse
ahci 33248 1
libahci 27215 1 ahci
libata 181461 2 ahci,libahci
xhci_pci 12675 0
ehci_pci 12512 0
scsi_mod 147395 2 libata,sd_mod
xhci_hcd 152471 1 xhci_pci
ehci_hcd 69979 1 ehci_pci
usbcore 199382 7 uvcvideo,rtsx_usb,ehci_hcd,ehci_pci,usbhid,xhci_hcd,xhci_pci
usb_common 12561 1 usbcore
i8042 18002 2 libps2,ideapad_laptop
serio 18282 6 serio_raw,atkbd,i8042,psmouse
i915 1002518 3
button 12953 1 i915
intel_gtt 17848 1 i915
i2c_algo_bit 12744 1 i915
video 22205 1 i915
drm_kms_helper 98881 1 i915
drm 273079 5 i915,drm_kms_helper
i2c_core 50240 7 drm,i915,i2c_i801,drm_kms_helper,i2c_algo_bit,v4l2_common,videodev
I have blacklisted "usbtouchscreen" module
It seems to be detected, but i have no idea how to make it work, it isnt even registering any kind of touch event, i even tried installing eGalax driver from AUR, it still didnt work.
Please help me by pointing me in the right direction!
Any help is appreciated. Thank you!
Last edited by kshergil (2015-04-20 19:08:28)

i posted output of that command without starting X
Here is complete output after starting X
[samtech@M4800 ~]$ journalctl -b | grep -i bluetooth
Dec 10 21:37:45 localhost kernel: Bluetooth: Core ver 2.19
Dec 10 21:37:45 localhost kernel: Bluetooth: HCI device and connection manager initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: HCI socket layer initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: L2CAP socket layer initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: SCO socket layer initialized
Dec 10 21:37:45 localhost kernel: Bluetooth: hci0: read Intel version: 370710018002030d00
Dec 10 21:37:45 localhost kernel: Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.7.10-fw-1.80.2.3.d.bseq
Dec 10 21:37:45 localhost kernel: Bluetooth: hci0: Intel Bluetooth firmware patch completed and activated
Dec 10 21:39:12 localhost NetworkManager[308]: <info> Loaded device plugin: /usr/lib/NetworkManager/libnm-device-plugin-bluetooth.so
Last edited by samtech09 (2014-12-10 16:52:30)

Detected but not transferring

Your comment is awaiting moderation.
For some reason everything is working (camera detected and controls working) but the only problem is that when I take a picture it shows up on my camera screen and says no card detected and doesn’t transfer to where its suppose to go in my lightroom library…frustrated especially since I know its worked previously. The only reason I’m changing back to sad tethering through lightroom is because canon has not upgraded their software for yosemite on mac. Thanks in advance for any help concerning this issue.

Canon 5D Mark III
Lightroom 4.6
Mac Yosemite
It worked before but not sure if it is Yosemite that is causing the problem...everything looks good until I press the shutter and the picture shows up on the camera screen but doesn't transfer to lightroom. It is mind boggling. Thanks for any help.

Can control desktop via devices, but not streaming TO devices?

Just got "Remote" app, and have iTunes on my PC/desktop. I've turned on Home Sharing on both desktop iTunes and on iPad 3 and iPhone 5. I can browse iTunes just fine from devices, and control my desktop just fine from here in another room, but the music is not streaming to devices as I believe it should.
What step am I missing? In "Settings" in both remote devices, I don't see a "More" option in either "Music" or "Videos" like the online instructions say.
Suggestions?
Thanks

Hi
+"Is it possible that my computer at work only accepts incoming connections but can't connect to the outside?"+
Yes. Some network environments (typically Windows Active Directory/ISA Servers) block outbound VPN and/or VNC connections. I have known this at a number of sites I support. Especially educational sites where you may be dealing with more than one filter/proxy. Outbound connectivity may be allowed locally but may be blocked further upstream.
Has it ever worked? If it has in the past and it's not working now that may be because your home IP address (external one) has changed? Residential IP addresses are generally dynamically assigned. You may want to consider logmein instead? This makes connectivity possible via standard http ports.
HTH
Tony

My nano has been detected, but not identified. What do I do?

Help. I plugged in my iPod, and a little warning showed up that said, "An iPod has been detected, but could not be identified properly. Please disconnect and reconnect the iPod, then try again." Guess what? I did that maybe thirty times. Didn't work. Advice?

First I assume youre using ipod nano 5g and you have downloaded newest itunes 9?
(thats a must).
Something that often gets usb devices to run again: (i dont run vista but you can google how to find the info here is one link as to how to find device manager in vista;http://pcsupport.about.com/od/windowsvista/f/opendmvista.htm)
Once you find device manager the basic info below applies:
Plug the nano in. Now in your Start menu, right-click "Computer" and select "Manage". Click "Device Manager".
"Expand "USB devices". Can you see an entry in there for the Apple iPod driver? If so, right click on that and select "Uninstall" Or if it offers to repair it can try that first. Click OK. (The uninstall choice may take a while, leave it to its own devices for a while. this only uninstalls drivers not itunes to my knowledge).
After the driver uninstalls, unplug the nano. Wait until it has finished saying OK to disconnect on the nano screen
Now plug the nano back in. This should reinstall the driver"
I found this info in the other forum for connecting nano to windows but Ive used it in past.
another link with info: http://discussions.apple.com/thread.jspa?threadID=2293079&tstart=0
And from apple info: http://support.apple.com/kb/TS1369
Message was edited by: slothofms7

SD card detected but not assigned a device

Similar Messages

Maybe you are looking for