SDM on 7600 series

Hy,
I have a 7609 and when logging with SDM v2.4 it says, it is an unsupported router.
At: http://www.cisco.com/en/US/products/sw/secursw/ps5318/prod_installation_guide09186a00803e4727.html#wp37069
I can't see the model, though I was wondering isn't there any other possibility of running SDM on this one? Maybe a newer SDM version?
Or if not SDM, other Cisco software ?
Regards,
Florin.

Please try the latest version. It should support 7609.
http://www.cisco.com/en/US/docs/security/security_management/cisco_security_manager/security_manager/3.2.2/compatibility/information/csmsdt322.html

Similar Messages

Cisco 7600 Series Ethernet Services cards types & queue values

Hello,
There is different types for the Cisco 7600 Series Ethernet Services cards.
( More expensive cards with high queue values and less expensive cards with
low queue values.)
http://www.cisco.com/en/US/prod/collateral/routers/ps368/data_sheet_c78-549419.html
Hardware queues
ES Plus XT 40G line cards
• 128,000 ingress queues
• 256,000 egress queues
ES Plus XT 20G line cards
*• 64,000 ingress queues*
• 128,000 egress queues
Hierarchical QoS (H-QoS)
http://www.cisco.com/en/US/prod/collateral/routers/ps368/data_sheet_c78-570730.html
Hardware queues
Cisco 7600 Series ES Plus Transport 40G and 20G Line Cards
*Supporting up to 16 level 4 queues per physical port*
Hierarchical QoS (H-QoS)
Low queue cards have got only 4 queues per physical port. High queue cards
have got minimum 64.000 queue. This is very huge difference. In what kind
of scenario do we have to use the High queue cards ? Could you give some
examples please ? Kind Regards.
Burak

HI Burak,
Each time you configure a class with bandwidth allocation or shaping,.. a queue will be used so if you use such card to provide QoS for a lot of subscribers sharing the same interface, you will need a lot of them !!
HTH
Laurent.

Cisco 7600 Series (7603) Router Information

Hello,
Does anyone have a link or reference to a good description of the Cisco 7600 boot process and various memory heirarchy functions? I'm looking for information on what should be in NVRAM, FLASH, SUP-BOOTFLASH etc. Thank you.

You can find all the 7600 series router info here.
http://www.cisco.com/en/US/products/hw/routers/ps368/products_data_sheet0900aecd801c5cab.html
http://www.cisco.com/en/US/products/hw/routers/ps368/prod_literature.html
HTH,
Sundar

Cisco 7600 Series can't back up it's config using Ciscoworks

We have a problem with Ciscoworks. Our client's Cisco 7600 can't back up it's configuration with Ciscoworks, while the rest of the devices can. They are all enrolled and discovered in the Ciscoworks of our client. Do you have any idea how to troubleshoot this? Thanks!

Have you partitioned the drive and formatted it Mac OS Extended (Journaled?) If not, try that and see if it helps:
Extended Hard Drive Preparation
1. Boot from your OS X Installer Disk. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.
Steps 4-6 are optional but should be used on a drive that has never been formatted before, if the format type is not Mac OS Extended, if the partition scheme has been changed, or if a different operating system (not OS X) has been installed on the drive.

IP SLA/Ethernet OAM on Cisco 7600 Series

Not sure if this is the appropriate place to post this discussion, so I appologize in advance if it is not.
I'm looking for iformation if CFM Local Maintenance End Point configured on Cisco 7606 router is able to respond to the Y.1731 Performance Monitoring (DMM/DMR ).
I know I can use IP SLA to configure Y.1731 PM measurements, but I just need a reflector that will answer for incoming DMM messages with DMRs.
Thanks

Not sure if this is the appropriate place to post this discussion, so I appologize in advance if it is not.
I'm looking for iformation if CFM Local Maintenance End Point configured on Cisco 7606 router is able to respond to the Y.1731 Performance Monitoring (DMM/DMR ).
I know I can use IP SLA to configure Y.1731 PM measurements, but I just need a reflector that will answer for incoming DMM messages with DMRs.
Thanks

Lexmark 7600 Series reinstall

Here are the reinstall instructions I got from Lexmark Support. Has anyone tried these?
<<We have the driver available online for your X7675 printer to work with MAC OS
10.6 Snow Leopard operating system. You need to delete all software associated
with the Lexmark printer first before installing it again. Below are the steps
on how to do it:
1. Go to HD>Library>Printers and drag the Lexmark folder to trash.
2. Click HD>Library>Printers>PPDs>Contents>Resources and drag the Lexmark
files to trash.
3. Open HD>Library>Receipts and drag the Lexmark files to trash.
4. Click HD>Library>Applications Support drag Lexmark files to trash.
5. Go to HD>Library>Image Capture>TWAIN Data Sources and drag Lexmark file to
trash.
6. Click HD>System>Library>Extensions folder and drag Lexmark files to trash.
7. Empty the trash.
8. Open Disk Utility and then do repair Disk Permission.
9. Reboot computer (it may take a few minutes to boot up completely).
Installation procedures for your Lexmark X76750 printer:
1. Click on this link and then download the driver, http://support.lexmark.com/index?locale=en&productCode=LEXMARKX7675&userlocale=EN_US&segment=DOWNLOAD&os=MAC_OS_X_10.6&page=downloadsList&oslo cale=enUS#2
2. Remove the USB cable before running the installation wizard again.
3. Follow the step by step instructions on configuring it wirelessly.
If you have any more questions or concerns, please contact me at your
convenience and I will be happy to assist you. (If I am not available, another
representative may reply to your request.)or contact our Technical Phone Support
at 1-800-LEXMARK(539 6275) for assistance. We’re open Mon - Fri: 8 am - 11 pm;
Sat & Sun: 11 am - 8 pm, Eastern Standard Time. >>
Phil

Had something similar with my Prevail 705. I ended up deleting the print queue, downloading the new printer driver from the Lexmark web site, then re-adding the print queue. I then did a software update from finder which installed the latest driver (I thought that was what I had done myself) Now it is all working correctly and I have now got back the use of the scanner etc.

Cannot print with Lexmark 7600 after installing Lion

Since installing Lion I haven't been abe to print. I use a Lexmark 7600 series. I reinstalled the printer a couple of times and I just downloaded the latest software update for the printer. The printer installs and I can see it in my system preferences but nothing happens when I click the print button. Not even an error message. I have tried both wirelessly and plugging in to the phisical printer. My other computer with Snow Leopard still prints without problems.

plane sailor wrote:
Tried all that and some but still can't get the lexmark to print. Guess I'll have to speak direct to Lexmark and ask them when their new drivers will be available.
We had similar problems with a Brothers printer just today. I suspected the driver was faulty but had the same results after a fresh software download from Apple, and one from Brothers web site. I print using a USB cable to my mac and my wife, who is running SL, prints wirelessly through my mac. We switched the cable to her mac, thinking this was a Lion problem, but had the exact same problem you describe above. A call to Brothers coached me through my System Preferences>Print & Scan> to select each printer in the "Printers" window and remove by clicking the "-" symbol. Then click "+" symbol and select the correct driver. Then select that printer as the "Default printer" in the lower dialog window.
Hope it works for you.

Which is the maximum number of simultaneous IP sessions on 7600 with/out SAMI?

Please I need help from someone who has ever wondered and get to know the maximum number of simultaneous IP sessions on 7600.
On the documentation, this is the applicable information that we find regarding the number of sessions:
http://www9.cisco.com/en/US/docs/ios/isg/configuration/guide/isg_acess_sub_sessns_ps6922_TSD_Products_Configuration_Guide_Chapter.html
Beginning in Cisco IOS Release 12.2(33)SRE, the Cisco 7600 router supports IP subscriber sessions only on the SIP400 and ES+ line cards
The Cisco 7600 router enforces limits on the number of IP subscriber sessions per line card and router chassis. If the number of active sessions exceeds the following limits, an error message displays:
- Cisco 7600 chassis—32,000 subscriber sessions (supported in Cisco IOS Release 12.2(33)SRE1 and later releases)
- ES+ line card—4000 subscriber sessions per port group; 16,000 sessions per line card (supported in Cisco IOS Release 12.2(33)SRE and later releases)
- SIP400 line card—8000 subscriber sessions (supported in Cisco IOS Release 12.2(33)SRD4 and later releases)
Let us suppose that we use the SIP400 line card, since ES+ is far from our networking requirements.
Please confirm/answer the following:
No special license is required to use ISG with SIP400.
Is the 8000 session limitation per SIP400 module or per SPA attached to it?
I read in the documentation, that the SAMI card enhances the maximum number of ISG sessions:
http://www.cisco.com/en/US/docs/ios/isg/configuration/guide/isg_sup_sami_blade.html
The ISG Support for SAMI Blade feature combines the subscriber management features and functions of the Cisco Intelligent Services Gateway (ISG) with the processing power of the Cisco Service Application Module for IP (SAMI). The Cisco SAMI blade has six PowerPC (PPC) processors and occupies just one slot in the Cisco 7600 series router. This means that you can support many ISG features for up to 600,000 subscribers on a single router.
We then assume that the SAMI blade overcomes the limitations noted above: 32,000 session/chassis and 8,000 sessions/SIP400. Correct?
No extra license is required to use ISG with SAMI.

How I can load a license in a home agent (modulo SAMI), which is installed in a 7606-S router?.

Ampliacion memoria 7600 de 1GB que usa BGP

Buenos días¡¡¡¡
Tenemos este equipo, un router 7600 que se utiliza para bgp e intercambia 500.000 rutas con un proveedor internacional Cogent.
Tiene muchas pérdidas de pines hacia direcciones de internet. Tiene 1 Giga de memoria.
Le hemos comprado 2 módulos de 2 gigas “MEM-RSP720-2G”.
Pensamos que la perdida de pines es porque no tiene recursos suficientes para la tabla FIB.
FUJINRTMORSE#sh mls cef max
FIB TCAM maximum routes :
=======================
Current :-
IPv4 + MPLS         - 192k (default)
IPv6 + IP Multicast - 32k (default)
Tenemos tres slot , dos para routing y uno para switching.
1º Qué combinación es la mejor para poder aumentar la table FIB. Ponemos un módulo de 2 gbit en el slot 1 y otro en el slot 3 ¿?
2º Es compatible con esta supervisora RSP720-3C-GE       los módulos de memoria MEM-RSP720-2G
FUJINRTMORSE#sh mod
Mod Ports Card Type                              Model              Serial No.
1    2 Route Switch Processor 720 (Active)    RSP720-3C-GE       JAE1113AQ5P
3   48 48 port 10/100/1000mb EtherModule      WS-X6148-GE-TX     SAL085071RH
Mod MAC addresses                       Hw    Fw           Sw           Status
1 0019.5679.9090 to 0019.5679.9093   5.2   12.2(33r)SRB 12.2(33)SRB7 Ok
3 0012.80f8.1370 to 0012.80f8.139f   6.1   7.2(1)       8.6(0.434)BA Ok
Mod Sub-Module                  Model              Serial       Hw     Status
1 Policy Feature Card 3       7600-PFC3C         JAE11129SD6 1.0    Ok
1 C7600 MSFC4 Daughterboard   7600-MSFC4         JAE1114B72R 1.0    Ok
Mod Online Diag Status
1 Pass
3 Pass
Gracias.

Hello.
As I understood the problem: FIB is limitted to 192K prefixes (while full BGP view requires 500K+).
This is due to the RP you are using - RSP720-3C-GE, this is not because of RAM memory.
Do be able to process full BGP table you need XL version, for example, RSP720-3CXL-GE.
PS: please find datasheet here - http://www.cisco.com/c/en/us/products/collateral/routers/7600-series-routers/product_data_sheet0900aecd8057f3b6.html
PS2: please write your questions/comments in English.

IDSM-2 blade in a 7600 router

Will the IDSM-2 blade work in a 7600 series router? Only documentation I see is that it is supported in the Catalyst 6500

Yes it will.

IPS on 1900 series Router

This should be a simple question.
Customer is thinking about the whole IDS/IPS environment.
He has some 1921 routers.
Am I correct is saying that If the router has the FL-SEC installed, then all they would need is to purchase the CON-SUSA-1921SEC subscription?
And if he has a plain router, then he needs to add the FL-SEC and then the CON-SUSA-1921SEC?
Thanks

Within the Cisco Virtual Switching System, one chassis is designated as the active virtual switch and the other is designated as the standby virtual switch. It should be noted that there is no requirement that the two members of the Cisco Virtual Switching System use the same chassis type. The members consisting of the Cisco Virtual Switching System can be different chassis with varying slot counts. Additionally, note that no Cisco 7600 Series chassis will be supported after the system is converted to Cisco Virtual Switching System mode. The initial release of the Cisco Virtual Switching System supports only one Supervisor Engine 720-10G VSS per chassis. A subsequent software release will allow for redundant supervisors to exist in a single physical chassis within the VSS.

VPLS on 7600

Can someone tell me on ehat supervisor engine on 7600 series router and what Interface Cards is VPLS supported? Additionally, can the VPLS, emulate the STP algorithm, in case a customer requests to interconnect 3 sites with redundant uplinks to PE Routers?

Check out the following link, should answer your questions:
http://www.cisco.com/en/US/products/hw/routers/ps368/products_configuration_guide_chapter09186a00801e5c06.html#wp1231162

7600+RSP 720-3CXL and 6500 Gbit ethernet modules (WS-X6748-***) compatible?

Hello all,
We are planning the replacement of a 7206 with a 7603-S, 7604 or 7606-S with RSP 720-3CXL to support full internet routing. The problem is RSP720 comes with only 2 x SFP and we need more L3 interfaces to terminate on the router.
Can the above configuration (7600 with RSP720-3CXL) work with WS-X6748-** line cards?
The "relevant interfaces and modules" link for the 7600:http://www.cisco.com/en/US/products/hw/routers/ps368/products_relevant_interfaces_and_modules.html does not list these as options.
If these are compatible, whats really the difference between a 6500 linecard and a SIP+SPA gbit configuration? (besides price)
Thanks in advance

Mario
They are listed under the Ethernet part of the table -
Cisco 7600 Series / Catalyst 6500 Series 10/100 & 10/100/1000 Ethernet Interface Modules
10/100 & 10/100/1000
Data Sheet
still worth checking the release notes to check your supervisor/IOS supports them.
As for difference, well the 67xx cards are purely ethernet, they don't support any other encapsulation whereas the SIP, from a quick check supports many encapsulations, although not ethernet.
I'm not that familiar with the SPAs but for example on the 67xx cards you cannot configure shaping which may be an issue for you. I don't know whether the SPAs permit shaping or not. Obviously you get a lot more port density using 67xx cards.
Only thing i can suggest is going through datasheets to see the difference.
Jon

EoMPLS over interface VLAN on 7600??

Hi all,
I ve read EoMPLS will not work on interface VLAN's in 7600 series routers... Is it for any specific IOS bug (if so is the same be fixed?) or the platform itsefl will not support...
Because we have an EoMPLS customer who is not able to work on interface VLAN..
Thanks in advance....

I got the below message as well:
LAB-R5-7604-CDAC-II(config-if)#mpls ip
MPLS CONFIG on LAN NOT RECOMMENDED: Cross-connect is currently configured
on interface vlans and WAN interfaces are facing the MPLS core.
By configuring MPLS on LAN interfaces, AToM on vlan interfaces may be non
functional.
LAB-R5-7604-CDAC-II(config-if)#mpls mtu 1546

MPLS-TE on 7600?

Does anyone have links to MPLS-TE 'tunnel mpls' support for 7600 series? Is the extent of MPLS support in the 7600 limited to MPLS VPN and EoMPLS?
Thanks,
Greg

Mainly looking for the basics right now.
interface Tunnel14
ip unnumbered Loopback0
tunnel destination 36.11.1.17
tunnel mode mpls traffic-eng
tunnel mpls traffic-eng autoroute announce
tunnel mpls traffic-eng autoroute metric absolute 500
tunnel mpls traffic-eng bandwidth 100
tunnel mpls traffic-eng priority 2 3
tunnel mpls traffic-eng affinity 400
tunnel mpls traffic-eng path-option 1 explicit name 14a
tunnel mpls traffic-eng path-option 2 explicit name 14b
ip explicit-path name 14a
next-address 14.14.14.14
next-address 15.15.15.15
ip explicit-path name 14b
next-address 41.41.41.41
next-address 51.51.51.51
Also, I assume fast reroute is not available yet?
Thanks,
Greg

SDM on 7600 series

Similar Messages

Maybe you are looking for