Seagate Backup Plus

I just installed Seagate Backup Plus on my Macbook Pro and am not seeing a user manual anywhere. It installed just fine, saved all of my documents etc. - took four hours. Now I want to make sure I don't lose the data on my computer.
Question - if I delete files on my computer, and I have the external drive set a Time Machine - when I plug the drive into my computer, will the files I deleted in my computer then be deleted on the drive? Because it is saving the changes from my computer - it will also delete the files on the drive?????
Also, I'm trying to see the files in the drive - they are there - it is showing in the number of GB used. The instructions etc. say go to the Dashboard - where is the dashboard? I cannot find it anywhere! I am not seeing my files in the drive.

No such thing as 'wasting money on a backup'
Ideally you need 2 external HD anyway, ....backup and archived important data.
* Also a lot of people use carbon copy cloner or (my fave) SuperDuper to make an exact copy of the HD that is bootable. So if the HD crashes, 15 mins you throw in the clone and your back and running.
external storage, quality too, is absurdly cheap right now.
Heres superslim external HD.
see this: only 7mm thick
$50
http://www.amazon.com/Toshiba-Canvio-Portable-External-Drive/dp/B009F1CXI2/ref=s r_1_1?s=electronics&ie=UTF8&qid=1377642728&sr=1-1&keywords=toshiba+slim+500gb
Or better still this HUGE HD, which is very small, very reliable and very cheap:
2 Terabytes, 2.5" and only $119
http://www.amazon.com/Toshiba-Canvio-Basics-Portable-HDTB120XK3CA/dp/B00ARJD56K
Its "updated design" cousin is here for $7 more ($127)
http://www.amazon.com/Toshiba-Canvio-Connect-Portable-HDTC720XK3C1/dp/B00CGUMS48 /ref=sr_1_4?s=electronics&ie=UTF8&qid=1379182740&sr=1-4&keywords=2tb+toshiba
Considering how many YEARS some people work on their data, and pics of dead loved once you CANNOT replace, .....its not only important, its IMPERATIVE people have at the very least 2 copies of that data.
What cost for priceless data when it comes down to a $65 hard drive???

Similar Messages

How can I transfer files from one external HD (WD My Passport) to another external HD (Seagate Backup Plus)? WD drive was improperly ejected and Finder no longer recognizes it. Tried fixing with Disk Utility but failed.

How can I transfer files from one external HD (WD My Passport 2T) to another external HD (Seagate Backup Plus 2T)? WD drive was improperly ejected (although we did tell it to eject) and now Finder no longer recognizes it. Using MacBook Pro and I just upgraded to Yosemite before this happened. Was told at Apple Store to use Disk Utility to repartition, but it failed. It says to backup files and restore. But how do I backup files? Or would appreciate any other suggestions to repair drive.

You may drag & drop between external hds.
Should you run into trouble.
Take the exernal drive appart. Take out the harddrive. Try reading the data via a usb adapter. Put a household finan on the hd.
http://www.cablewholesale.com/products/usb-firewire/usb-2.0-products/product-40u 2-01000.php?utm_source=Nextag&utm_medium=cpc&zmam=54972865&zmas=1&zmac=4&zmap=4 4 77

Seagate Backup Plus 3 HFS formatted drive when plugged in to new Airport Extreme causes it to shut off and shows constant amber light. Please help.

I just purchased a new 3tb Seagate Backup Plus 3 to attach to my new Airport Extreme. When I plug the Seagate's USB in to the AE, the drive starts spinning, clicks and then the AE light turns amber and the wifi connection is lost. After I unplug the HDD the signal comes back and the AE light turns green. I have even tried using 3 partitions on the drive to see if that would work. I have a 1tb portable drive that has worked on the AE but this new drive doesn't. I have formatted both drives with Macdrive 9 pro and only the portable drive has worked. I've tried everything I could find on the internet to resolve this. I hope someone out there can help.

When it blinks amber, use the airport utility to peek at the status to see what error it's telling you. I'm guessing you MAY need to use a powered hub...

Seagate Backup Plus Slim External USB 3 Hard Drive Not Working with Mac Pro

Hi, I have just purchased a brand new Mac Pro. I have three 2 TB Seagate Backup Plus Slim External USB 3 hard drives that just don't jive with the new Mac Pro's. When the drive is connected, I cannot access the drive, read/write or even format. Finder completely locks up and the drive cannot even be force ejected. When I try to format, Disk Utility either spits out an error that the drive cannot be read, or simply locks up. This happens regardless of the OS on the Mac Pro. I am currently running 10.10.2
I have ruled out an issues with the drives, as I have tested all of them on a variety of systems and OS's, including Power Mac, Mac Book Pro, PC, OS 10.7, 10.8, 10.9 as well as on Windows. I have tried formatting in every file system including Mac OS Extended, Mac OS Extended (Journaled), NTFS and exFAT. ALL other systems have no issues with the drives. Apple has replaced my Mac Pro with a brand new one and the drives still behave the same way. Furthermore, I have tested the drives on three other Mac Pro's at work and they all reject the drives. So, on their own, there is nothing wrong with the Mac Pro, or the drives. However, the configuration of them together is wreaking havoc.
I have contacted Seagate, and this was their response:
The most recent version of the Backup Plus drives use the USB Attached SCSI (UAS) standard to increase transfer rates. It's possible that the drivers being used currently on your Mac Pro are having issues using this feature with the standard USB 3.0 drivers installed. I would recommend contacting Apple to check for any driver updates or see if they any suggestions for issues involving drives using UAS.
I have also started a case with Apple Support (Case # 755934373) and am waiting to hear back regarding Seagate's response. I've spent DAYS trying to troubleshoot this and am now at a complete loss. If anyone has any ideas, I'm all ears (or eyes in this case).
Thanks!

Hi danielsh6,
I recently bought the new Lacie Thunderbolt 2 D2 3TB and I had the same problem as you, i have a macbook pro early 2011, those support thunderbolt but many times there is a bug that doesn't let you connect any thunderbolt drives to your computer. The solution I found was installing this update:
Thunderbolt Firmware Update v1.0
Before doing this I would recommend you updating to mountain lion (not yosemite yet as there is still some glitches and more on preview's macbook pro's).
Hope this helped!
Forest

Okay so I have a Seagate Backup Plus Drive External Hard Drive and I'm trying to get it to backup Applications and stuff on the dock such as iPhoto, and Photo Booth.

It's one of these External Hard Drives. I go to the Finder folder and go to the "Seagate Backup Plus Drive" to see what's in there and what I assume is that backups but the only thing that seems to be in there is folders from everything that is Desktop and a few Documents. The Applications folder seems to be empty and there are no folders for Photo Booth or iPhoto. Everything from GarageBand and iTunes seems to have been backed up according to the Seagate Backup folder when it is plugged in and opened. How do I get this thing to backup everything from Photo Booth and iPhoto? And by the way, I can't seem to access Time Machine the way you get it to where you can go back in time and see all of your stuff from previous dates. I don't know if this is important or a crucial part but I seem to not be able to access the actual time Machine Layout.

Simple on that one - Download Carbon Copy and follow the steps below:
if you have access to an external USB enclosure use it, or you can buy one for $10...
install your new ssd in the usb enclosure - connect to your macbook...
open disk utility and format/erase your ssd - mac os extended journaled.
open carbon copy - clone your drive with it - source (your old drive) + destination (your ssd).
once the clone is done, turn your macbook off - take old hard drive out - install new ssd in....
turn your macbook on - if boot time is more than 40 secs to desktop - go to system preferences - startup disk and select your new ssd as the startup disk - restart your macbook - should be about 14 sec boot time now.
install your old hard drive in your usb external enclosure and use it as a backup drive.
good luck

How do I reformat my External Hard Drive (Seagate Backup Plus).

Hello everyone. How do I reformat my External Hard Drive (Seagate Backup Plus Portable Device). I accidentally clicked to use it with Time Machine and my hard drive is of little use now. When I open my hard drive, it just shows 'backup', the same thing when I open it with Windows. Thinking of reformatting it back to be used to Mac and Windows. And not use it again with Time Machine. New to Apple, appreciate the help

Hello,
"Thinking of reformatting it back to be used to Mac and Windows. And not use it again with Time Machine"
If you want to format the External drive as universally compatible, your best bet is to format it as exFAT. Note that reformatting the drive erases all contents of the drive.
1) Open Disk Utility located in /Applications/Utilities/ (or simply type it in spotlight and the application will show up)
2) Select the external Hard drive
3) Click the 'erase' tab.
4) Under format: select exFAT
5) Click "Erase" in the lower right hand corner to reformat the drive.

I am using a Seagate backup plus portable drive on my iMac 7 with OSX 10.9.2. At startup up I always get a popup window stating "The disk you inserted is not readable by this computer. I click ignore and everything seems OK. Is it?

I am using a Seagate backup plus portable drive as my time machine backup on my iMac 7 with OSX 10.9.2 Mavericks. At startup I always get popup window stating "The disk you inserted is not readable by this computer..? I click ignore and everything seems to be OK. Time machine seems to be backuping up to the seagate. I can open time machine and see the history of backups. Why does this message come up at startup of computer????

If you installed the Seagate software, remove it according to the manufacturer's instructions.

Seagate Backup Plus won't show up anymore

I have a 1TB Seagate Backup Plus for Mac Portable Drive. I bought less than a year ago. It had been working great. Until recently. Since the last week or so, when I plug it in my Macbook Pro (10.9.5), the external drive lights up but it doesn't show up on my desktop. I checked Disk Utility as well. Nothing there either. It simply doesn't read it.
I have had OSX Mavericks installed for quite a while now. Recently I tried to update it to Yosemite, and it looked like it worked, but apparently not. My "About this Mac" still shows 10.9.5. Maybe it just updated to a higher version of Mavericks. I am wondering if the OSX might have something to do with my ext. drive not getting read. I already tried it on a different mac with a much older version OSX. Doesn't show up there either.
Of course, I also checked that the problem is not with my connection chord. I tried a different chord with my drive, but no changes. I also tried it on a friend's computer using his chord (which definitely works), but it doesnt show up on his computer either.
Any thoughts what the problem and the fix might be? I have important data on this hard drive, and have also backed up my Timeline on it. I cannot afford to lose my data, in any circumstances. Please help.
Thanks

Take out the HDD from the enclosure and install it in a different one. It could be that the internal SATA connection board is faulty.
Do not dismiss the possibility that the HDD has died.
Ciao.

I baught Seagate Backup plus 2T hard drive to use as my Backup time machine. But its not working when i connect to time machine its not coping files, it keep saying preparing files. Can someone help me please...

i baught Seagate Backup plus 2T hard drive to use as my Backup time machine. But its not working. when i connect to time machine its not coping files, it keep saying preparing files. Can someone help me please...

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Options for Seagate Backup Plus for Mac/Windows

I have a new Mac-mini (my first Mac since my original Mac 128), and just got a 3TB Seagate Backup Plus. It's so new, I haven't even read up on Time Macine though I assume that's the way to go.
I originally had in mind partitioning the Seagate with one HFS+ for the Mac and one NTFS for my Windows laptop (Win7) and old Windows desktop (XP). The latter is mainly for storing files in a place where it will be convenient to use them on the Mac. But with all the threads about partition and other errors, I'm wondering if that's not so wise.
The obvious alternatives are leave the drive as NTFS and find something other than Time Machine for backing up the Mac - or format it as HFS+, use TM to backup the Mac, and install HFS+ drivers at least on my laptop.
I usually like to try and research these sorts of questions directly, but with the learning curve moving to the Mac, and all sorts of other things, it would take me to next year to find my ideal solution. So for now, I'm just looking for suggestions on a backup strategy for the Mac that would, in addition to backups, leave space for manually archiving Mac files as well as exploiting the spare space on the external drive for some Windows purposes. (Not much videos, mostly photos, finances, and eventually my main reason for getting the Mac, ios development.)
Thanks for any suggestions.
Gary

The following troubleshooter from Seagate may help: http://knowledge.seagate.com/articles/en_US/FAQ/213059en

Seagate backup plus won't read

So my seagate backup plus external hard drive won't be read by my Mac.
It's functional, I can hear it running fine when I plug it into my USB port but the only place my mac show's it's connected is in the system profiler, no where else.
I can't find it in the Finder or the Disk Utility.
Any ideas of how to get it to read?
I have important documents on it.

If the HDD is formatted NTFS, then it suggests that there is a problem with the PC. Check with the manufacturer.
Ciao.

Time machine, seagate backup plus

Hi ive bought a seagat backup plus external hard drive. Ive been using it to transfer files from a pc to my new mac. When i originally used it for the first time, i think it asked me if i was using it between both windows and mac formats so i said yes, and this has worked seamlesly.
Now all my files are on the mac, i want to use it for a time machine back up. Upon trying this it failed because it is not in the correct format i think.
So here is a couple of questions....
1- How do i give it the correct format?
2- Some of my family still use the windows pc, and i would have liked to have still been able to use the hard drive across both formats. So if i format for Time machine, will this not then be possible?
Thanks.

Sorry, an external that is used only for Time Machine.
see > Mac Basics: Time Machine backs up your Mac
Because sooner than later, Time Machine will use all the space on the drive.

How do put files on my external hd (seagate backup plus)

I have the seagate backup plus. I installed it for the mac. I just want to move files to it so i have room on my hard drive

Drive Partition and Format
1. Open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Apply button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
You can transfer files manually using drag and drop. You can perform backups using a backup utility or by enabling Time Machine in OS X preferences.
Suggested Backup Software
1. Carbon Copy Cloner
2. Get Backup
3. Deja Vu
4. SuperDuper!
5. Synk Pro
6. Tri-Backup
Others may be found at MacUpdate.
Visit The XLab FAQs and read the FAQ on backup and restore. Also read How to Back Up and Restore Your Files.

Unable to write to Seagate Backup Plus drive on Mac

I just installed a brand new Seagate Backup Plus drive on my laptop with the goal of being able to use it on Macs and PCs.Seagate's web site says this:
Using the drive under MacOS and Windows
If you want to use the drive under Windows and MacOS, simply leave the drive in the NTFS format that it has when shipped from the factory (say No to "Do you want to use this drive with Time Machine?", if prompted). Install the included software which has a special driver that will allow the NTFS partition to be read and written under MacOS:
Plug in the drive.
Open the Seagate Backup Plus or FreeAgent GoFlex icon that appears on the desktop.
Double-click the Seagate Dashboard Installer.dmg (Backup Plus) or Mac Installer.dmg (GoFlex) file on the drive and follow the prompts.
If the driver is not installed, then the drive will be read-only under MacOS.
The installation process seemed seamless, but I was never prompted to download an extra driver and it would appear that the driver either didn't install or doesn't work as advertised.
I've found a user forum via Seagate addressing the inability to write to a GoFlex drive on a Mac:
http://forums.seagate.com/stx/board/crawl_message?board.id=UPHD_and_PU&message.i d=3360
One solution was to download a different driver (http://www.macupdate.com/app/mac/24481/ntfs-3g), however when I tried this I got an error from NTFS-3G that said "NTFS-3G could not mount the Seagate Backup Plus Drive because the following problem occurred: /Library/Filesystems/fusefs.fs/Support/fusefs.kext failed to load - (libkern/kext) link error; check the system/kernel logs for errors or try kextutil(8). the MacFUSE file system is not available (71)"
I opened up the user guide, which instructed me to download MacFUSE, but the driver still wouldn't mount.
In the end, I simply re-formatted the external HD with ExFAT in order to be able to read AND write. Has anyone else had a similar problem, or found a different answer?

I thought that those particular Seagate drives shipped with the Paragon NTFS for Mac utility? If not, it's a $20 investment that you need to make.
Download and install and then format the drive as NTFS on your PC. Your Mac should then be able to both read and write files to the drive.
Clinton

Problem using Time Machine with Seagate BackUp Plus Pls HELP!!

I have a late 2006 iMac (running OS 10.5.8) & am trying to back up using Time Machine with a new Seagate BackUp Plus drive. When I select the Seagate drive in Time Machine it tells me I msut first erase the (Seagate) disk. When I hit ERASE, I get a Time Machine error : COULD NOT UNMOUNT DISK. I see from various posts that 10,5 & 10,6 have issues with some external drives so want to upgrade to Mavericks (to get around this incompatibility issue): HOwever apparently my iMac is too old (by 1 year) to allow this. Can anyone give me any advice on how to get my iMac content backed up via Time Machine using the Seagate BackUP PLus drive I bought (becasue it is supposedly "compatible with PCs & Macs".
Thank you!!
Wendy

Your Seagate drive should work just fine. If it doesn't have any important data on it, try re-formatting it with Disk Utility to blank it out. Or run the Disk verify/repair and see if you can get it to fix any problems.
I have a Drobo FS too. You probably need a firmware update, they issued one a while back to fix problems with Time Machine. Use the Dashboard or download it from their support site, http://www.drobo.com/support/updates.php
Just curious how long you let it run after it "stalled". If it is a big file it could just be taking a while to copy over, do you see activity lights on the USB drive? The first time you use time machine let it run overnight, it's going to take a while, after that it will update quickly.
While you're at it, you might want to verify your start-up disk too with Disk Utility.

My external hard drive (Seagate backup plus) has stopped working on my macbook 10.8.5

I've been using Seagate Backup Plus for a year now and suddenly it has stopped working on my Macbook Pro (mountain lion 10.8.5). When I plug it in, it lights up and I can hear it running, but it won't show on my macbook. I've checked on Disk Utility but it won't recognise the hard drive. I also tried going on Terminal to see if my hard drive is listed by putting "diskutil list", and it's not. I also make sure that external hard drives are visible on Finder. Since my hard drive is on NTFS format, I tried uninstalling and reinstalling the NTFS drive, and still it won't work.
My hard drive is working perfectly on other devices and PCs so I'm sure the problem is on my macbook. Usb ports of my macbook are also working perfectly.
Please help. Thanks.

Open Disk Utility (Applications>Utilities folder) and format the disk as "Mac OS Extended (Journaled)" with a single GUID partition. Your Mac should see the drive and you should be able to use if for backups, storage, etc.
Clinton

Seagate Backup Plus

Similar Messages

Maybe you are looking for