Searching for a cable terminal block combination that works with the PXI-2568

Hi,
Has anyone figured out a cable-terminal block combination for the PXI-2568. I have a hard time finding something useful and would appreciate any part/supplier information from users who purchased a PXI-2568. Thanks.

If you download the specifications document for the PXI-2568 from NI's website there is a section close to the end that talks about cabling and accessories. The PXI-2568 uses a standard 62 pin D-sub connector. The cable and terminal blocks for this connector can be found at large electronic suppliers. I hope this helps and have a great day!
Bryan Snarr
Application Engineer
National Instruments
Bryan Snarr
Field Engineer
Northern California
National Instruments

Similar Messages

I need a USB Headset with Mic to use for Webinar's and Go To Meeting sessions. There looks to be very few options that work with the Mac as they seem to be designed for Windows. Any suggestions on equipment?

I am looking for a binaural USB headset with microphone to use during Go To Meeting sessions and Webinar's. Seems to be little that works with the iMac and most of the web searches have not been encouraging. Any suggestions on units that work. I have a new iMac running Snow Leopard 10.6.8.
Bob

I am looking for a binaural USB headset with microphone to use during Go To Meeting sessions and Webinar's. Seems to be little that works with the iMac and most of the web searches have not been encouraging. Any suggestions on units that work. I have a new iMac running Snow Leopard 10.6.8.
Bob

How do I get a driver for KONICA MINOLTA C250 UV2.0.0 that worka with os 10.6.

Where do I find a driver for KONICA MINOLTA C250 UV2.0.0 that works with os 10.6.7 on my MBP

I googled, "C250" and come up with this web site:
http://onyxftp.mykonicaminolta.com/download/SearchResults.aspx?productid=831&fil etypeid=0
scroll 3/4 down the page. It's there. You can google too.

Search for all words in a table column that any of the words start with a certain letter

I have products table. Each row has a Description which may have a few words within it. I wanted to know if it's possible to search through it and find all descriptions that have match the search. But, I want it to consider it a match even if it's not the
first word of the description, but rather the start of any word in the description.
For example:
Descriptions
Nice Casual Gloves(This should show up, and although it's not in the very beginning of the description it's at the beginning of a new word.)
Nice Dressy Gloves(This should show up, and although it's not in the very beginning of the description it's at the beginning of a new word.)
Great Dresses (This should show up)
Fancy Outerwear
Glasses (This should show up)
Shoes
Sheer Stockings (This should not show up because although it has a "g" it's not in the beginning of a word.)
Boots
Galoshes (This should show up)
I would want to search within this list Where Description like 'G%' but I don't want it to only get the descriptions that start with "g" at the beginning of the description, but rather any "g" at the beginning of any word. I do not want
to get all descriptions that have a "g" somewhere in the word (then I could just do WHERE DESCRIPTION LIKE '%g%'), rather only if it somewhere within the description but at the beginning of any word.
Thank you so much
Debra has a question

The most perfect solution would be to get a CLR routine to either (a) Do a regular expression match, (b) Run a split routine at CLR speeds then do a simple LIKE, or (c) both (a) and (b). If your requirements grow to handle more and more complex searches,
you may have to do it that way eventually.
However, like the other answers, here's a way to do it reasonably well given your current requirements. You may have to tweak the REPLACE logic if you have frequent OTHER forms of word delimiters.
Method: Pull data; add space before and after original text; replace all common word separators other than space with a space (so for example, "(These pretzels)", "He said 'These pretzels are making me thirsty" and so forth would
be replaced with a space before "The"; then do a Patindex (you could do with just a LIKE also) on the search string prefaced with a space. Here's an example, stealing from table sys.messages just for ease of demonstration.
With SampleData as
Select top 100 *
, ' ' + Replace(Replace(Replace(Replace(text, '"', ' '), '''', ' '), '/', ' '), '(', ' ') + ' ' as TextPlus
from sys.messages
where language_id = 1033
Select TextPlus
, patindex('% The%', textplus)
from SampleData
where patindex('% The%', textplus) > 1
Same logic, in the most concise format:
Select top 100 Text
from sys.messages
where language_id = 1033
and ' ' + Replace(Replace(Replace(Replace(text, '"', ' '), '''', ' '), '/', ' '), '(', ' ') + ' ' like '% the%'

Are there any apps that work with the G2 to block calls reliably?

I know this subject has been covered but, I have been using Call Control for years since I bought Pro way back when. Worked fine up until I got the G2. Now it says that the only proven method of blocking calls is using MUTE CALLS. The send to voicemail and pickup/hangup options are NOT recommended. I have tried a few others, but they all seem to hijack the call screen. I'm not overly worried about Caller ID features in an app. I know Call Control is in beta with a new version that shows ID, but it's rough and not aesthetically pleasing. Blocking texts isn't a big deal for me either. I know a lot of these apps block texts, but require you to use their messaging portion of their app. Anyone know of a proven pickup/hangup or send to VM app that works on G2?

Call Control works well, but being a beta tester I can tell you that features are changing. It's getting better, but even the Premium users are going to have to pay for lookups after x number credits. IOW, Premium users get a few credits per month and free users have to pay each time. Until that app decides to do right by the Premium users who have already paid for the app long ago I use Contactive because the ID seems better and more accurate than Call Control, Whitepages Current, Truecaller, LineWhoscall, and CallApp. Contactive doesn't have a direct pickup/hangup nor a send to VM, but the info is more correct and that means I can better block calls based on better info.

Global Switches for Frame Blend and Motion Blur aren't working with the newest version of After Effects 2014.1.1

I have been using After Effects regularly since 1995. So this isn't an operator error.
I am on a new Mac Pro six core with OSX 10.9.5 and 32 gigs of RAM.
Is anyone else having trouble with activating frame blend and motion blur?
Occasionally I am able to get the global switch to appear to be on. It still won't activate motion blur or frame blend.

I'll answer my own issue. The global switches actually work. The distinct dark boxes that indicate when the global switches are enabled have been removed and replaced by a light blue outline of the switch icon.

The bonjour service has been disabled and i need it for sharing. I cannot get it to work with the services directions. It keeps telling me services stopping. HELP!

Bonjour has been disabled and i do not know how to enable. Been in the services and followed the instruction without results. Help. Thx.

Using Windows Firewall currently - Bonjour is ticked as an exception so it should be ok... but still no luck

Will my old wall charger for Zen Vision:M will work with the (New) Z

i bought a wall charger from amazon for my Zen Vision: M 30GB, will it work with the (New)Zen? i just bought the Zen 6 GB and it doesn't comes with an adapter, pretty bad move there, well, does it has the same plug? i hope it's compatible. thanks

sebastiankf,
That third party adapter from your Amazon link is hard wired specifically for the Vision:M and will not work with any other Creative player unless it has the same pin-outs using the same docking interface. The Creative AC-5V adapters will either have a coaxial power plug connection that will work with most of the Creative hard disk based players, except for the original NJB and Zen Micro, or a USB Mini-B plug that will work with all of the flash players that have a USB connection and the Zen Micro.

Does anybody know how to modify the driver for the Tektronix 370A curve tracer so that it will work with the 370B?

I am trying to control a Tektronix 370B curve tracer using LabView via a GPIB interface. However, there are no drivers available for download for the 370B. There is one available for the 370A, but it is not compatible with the 370B and I have been unable to figure out how to modify it to make it work with the 370B. Does anyone know how to modify this driver, or know of an existing driver that works with the 370B? Thanks!

Hi S _Bracht,
Yeah, unfortunately, the Tektronix 370B does not currently have an instrument driver and the driver for the 370A is not supported by National Instruments (it is just posted on our website as a courtesy) - so I am afraid that there is not really any more information on the differences that might exist between the two available from National Instruments. As an alternative, you can always develop your own driver using the VISA and 488.2 drivers + a copy of the user manual for the Tektronix 370B. Otherwise, you may consider speaking with Tektronix or getting ahold of a User Manual for the 370A and comparing some of the settings - there are likely some differences in your configuration options at the very least. Or, if someone out there has tackled this before and shares their knowledge...
Good luck!
Regards,
Anna M.
National Instruments

We are using apple tv to try to access our itunes account on the computer. We see our library of music but when we click on the song it searches for a long time and then says that it cannot access the itunes store. Any ideas on what we are doing wrong?

We are using apple tv to try to access our itunes account on the computer. We see our library of music but when we click on the song it searches for a long time and then says that it cannot access the itunes store. Any ideas on what we are doing wrong?

Welcome to the Apple Community.
Try the following steps, check whether things are working after each step where appropriate, before trying the next.
Restart the Apple TV (Settings > General > Restart).
Restart the Apple TV by removing ALL the cables for 30 seconds.
Restart your router.
Reset the Apple TV (Settings > General > Reset > Reset all settings)
Restore the Apple TV (Settings > General > Reset > Restore)

LabVIEW 6.1 If For Loop count terminal is zero then value going through the loop is not passed on to the output of the loop

Hello, one of our customers just encountered an execution error in a vi running under LabVIEW 6.1, which doesn't exist under LabVIEW 5.1 or 6.01. I have a simple vi that has two encapsulated For Loops. Two string arrays go in, one goes out of the outer loop. Inside the outer loop the first array is indexed. The string which results from this indexing is compared with all other strings from the second string array in the inner loop. If it matches one of the strings of the second array, it is not outputted, otherwise this string goes through the inner For Loop to the output of the inner loop and from there to the output of the outer loop. The count
terminal of the outer/inner loop is connected to the Array Size of the first/second string array. If the second array is empty, that means that the element in test from the first arry cannot match anything from the second array, so the element in test is send to the output of the inner loop and from there to the output of the outer loop. This works fine in LabVIEW 5.1 and 6.01, but NOT in LabVIEW 6.1. In LabVIEW 6.1 the inner loop is never executed if the count value is zero (which is correct), but the data line running through the loop is not executed either, which is different to what LabVIEW 5.1 and 6.01 do. There, the input string is sent to the output of the inner loop correctly even if the loop counter is zero. The solution is easy - I just have to connect the output of the outer loop to the data line BEFORE it enters the inner loop. But: I don't know if this is a LabVIEW 6.1 bug or if it is supposed to be a feature, but it brings some incompatibility in programming between the
different LabVIEW versions.
Best regards,
Gabsi

Hi,
When a for-loop runs zero times, all outputs are 'undefined' (and should
be).
Besides, how would LV know what the output of a not executed routine should
be?
It might be handled differently in LV5 and LV6, which is unfortunate. In
both cases, the result is undefined.
It's not a bug. It's just something that should be avoided in any LV
version.
> The solution is easy - I just have to connect the
> output of the outer loop to the data line BEFORE it enters the inner
> loop. But: I don't know if this is a LabVIEW 6.1 bug or if it is
In some cases this does the trick. But if the data is changed in the inner
loop, this will effect the results if the N is not zero.
Technically, I think the output in this construction is also 'undefined'.
But LV handles this as expected / desired.
Another solution is to use a shift register. If N is zero, the input is
directly passed through to the output.
Regards,
Wiebe.
"Gabs" wrote in message
news:[email protected]...
> LabVIEW 6.1 If For Loop count terminal is zero then value going
> through the loop is not passed on to the output of the loop
>
> Hello, one of our customers just encountered an execution error in a
> vi running under LabVIEW 6.1, which doesn't exist under LabVIEW 5.1 or
> 6.01. I have a simple vi that has two encapsulated For Loops. Two
> string arrays go in, one goes out of the outer loop. Inside the outer
> loop the first array is indexed. The string which results from this
> indexing is compared with all other strings from the second string
> array in the inner loop. If it matches one of the strings of the
> second array, it is not outputted, otherwise this string goes through
> the inner For Loop to the output of the inner loop and from there to
> the output of the outer loop. The count terminal of the outer/inner
> loop is connected to the Array Size of the first/second string array.
> If the second array is empty, that means that the element in test from
> the first arry cannot match anything from the second array, so the
> element in test is send to the output of the inner loop and from there
> to the output of the outer loop. This works fine in LabVIEW 5.1 and
> 6.01, but NOT in LabVIEW 6.1. In LabVIEW 6.1 the inner loop is never
> executed if the count value is zero (which is correct), but the data
> line running through the loop is not executed either, which is
> different to what LabVIEW 5.1 and 6.01 do. There, the input string is
> sent to the output of the inner loop correctly even if the loop
> counter is zero. The solution is easy - I just have to connect the
> output of the outer loop to the data line BEFORE it enters the inner
> loop. But: I don't know if this is a LabVIEW 6.1 bug or if it is
> supposed to be a feature, but it brings some incompatibility in
> programming between the different LabVIEW versions.
> Best regards,
> Gabsi

Just installed Firefox 4 but when I try to search for add-ons every result fails to find anything or the loading gui just keeps spinning. What should I try to fix this problem?

Just installed Firefox 4 but when I try to search for add-ons every result fails to find anything or the loading gui just keeps spinning. What should I try to fix this problem?

Glad you seem to have sorted things out.
The warning about the warranty is light hearted, I think at one stage it warned "here be dragons" but also intended to make us think as it warns that making changes may produce problems.

Searching for a folder in document library doesn't work properly if the folder is at the root level.

Hi,
I have a folder named FS0 on my sharepoint 2013 site. The folder is the first level folder under
Default Document library (Shared Documents). When I search for FS0 on the sharepoint site, the search result give a link to home.aspx and not the folder. If I search for any folder that is a second level folder in the library, I get a search result that takes
me inside the folder on clicking it. In my case, I search for a folder named FS1 which directly under FS0. The search result takes me inside FS1 in this case. How can I make the search result display proper links for root level folders also?<o:p></o:p>
Thanks
Pranava

Hi Pranava,
I couldn't reproduce this issue, when I create root folder FS0 in "Shared Documents" and start a full crawl, I click the FS0 link from search results page, it will open the FS0 folder as well as folder under FS0.
Please right-click the FS0 name hyperlink (e.g. mine is http://sp/Shared%20Documents/FS0) and paste in IE browser see if it could be accessed successfully.
Also test if other Shared Documents have this issue in other site collection or web applications, if not, run a full crawl may do a trick (please reset search index if only full crawl still doesn't work).
Thanks
Daniel Yang
TechNet Community Support

Do the cables for the 700p work with the 700wx?

I used to have a treo 700p that I broke when I dropped it from a 2nd story balcony onto concrete. I still have the box and whatever cables came with it. Now, I'm able to buy a 700wx for a real low price, but the seller only has the phone and the charger for it, no other cables. Would the cables for my 700p, like the sync cable work with the 700wx? If they would, this would work out real nice!
Post relates to: Treo 700p (Sprint)

Yes it will work most of the cables for the Treo series will work as it is an interchangeable cable, there is some exceptions, but in your case it will work.

I have Mail with 5 accounts. The problem is that one of them is constantly active, that is with the moving wheel showing a search for new mails.

I have Mail with 5 accounts. The problem is that one of them is constantly active, that is, with the moving wheel showing a search for new mails, while the others accounts are not active.

hello
Would not take the moving wheel as indication that account is active. There could be other reasons for it. From the menu Window, choose 'connection doctor' that will show you how each account has connected. Next, from the Window menu choose 'activity veiwer' that will show you exactly what activity is causing the moving wheel.

Searching for a cable terminal block combinatio​n that works with the PXI-2568

Similar Messages

Maybe you are looking for

Searching for a cable terminal block combination that works with the PXI-2568