Second audio missing

Hi Everybody,
I have a VOB file which has 2 audio streams. When imported in Pre only the first audio appears in the timeline.
The second one is missing. Are there any options I have to check out? Please advise if there is any workaround to get the second audio in Pre.
I have Pre Pro CS5.
Thanks
Shiva

You will need to rip the supplemental Audio Stream separately. Only the primary Audio Stream will be Imported from the VOB.
Good luck,
Hunt

Similar Messages

Why is audio missing from movie

why is audio missing from movie

I think I may have confused you a little bit, sorry. Hope this might be easier to follow.
1. Copied nieces VHS tape to DVD discs. Tape runs approximately 2hr. 39min.
2. Put first part on work copy 1. This consisted of the lead up to the ceremony and the ceremony itself, ending with still shots of the wedding party, in the park. About 1hr. 1min.
3. Put second part on work copy 2. This consisted of the wedding reception, beginning to end. About 1hr 38min. No possibility of overlapping content.
4. Ran both work copy 1 and work copy 2 on the VCR that's hooked up to the TV. (Not the Toshiba copy machine). Both ran through, beginning to end with no glitches.
5. Opened Adobe Premiere Elements and loaded work copy #1 so as to make three finished copies, one for bride and groom, one for bride's parents, one for groom's parents.
6. When placed on the timeline, contents of work copy 1 had no audio for VTS_01_1.VOB while VTS_01_2.VOB and VTS_01_3.VOB were whole.
7. Tried for several days to eliminate the problem with no success. A.P.E. showed file sizes of .99GB, .99GB and 47MB respectively. The 47MB is actually about 2 minutes of still pictures of       the wedding party. I was not going to attempt to burn the project until correcting the audio problem.
8. Wrote in to the community forum and happily received your response. Tried every thing you offered without success. Though I am thankful for all your time and effort. While nothing worked       so far, I have learned a few things and will retain my notes so as to keep this information at hand. (Don't know how you're able to maintain all that info).
9. At this point, in view of the results of step #4, I thought to try Windows DVD Maker to see what developed. Loaded work copy 1 into that program, which recognized the audio in the first clip       (VTS_01_1.VOB). I did not run the work copy, beginning to end, in this program. But I felt that as long as the audio was present in the first clip, this program would allow me to burn the           copy. When the burn button was pushed, I received the error message "Will Not Fit", and the duration of 30 min for clip 1, 30 min. for clip 2 and 25 hours and 30 min. for clip 3. Clip 3 being       the 2 minutes of still pictures. After trying unsuccessfully to remedy this problem it was time to try a different approach.
10. Opened A.P.E. and loaded work copy 2 onto the timeline. Successfully made three finished copies of this disk in a short period of time.
11. Took the VHS tape back to the Toshiba to make another copy (work copy 1A) of the first segment.
12. Played copy 1A in the TVs VCR and it played fine, no glitches.
13. Opened A.P.E. and put work copy 1A on the Timeline. This time there was audio in clip 1, which could be seen on the audio line, but it was the audio from work copy 2. This, even though       I had deleted the files from work copy 2.
14. Accepted the fact that this has become a career. Can't imagine what you're thinking. Since beginning this endeavor I have become much older and grouchier. My dog will no longer walk         with me. Neighbors go back in the house when they see me coming. Oh, and my wife sticks out her tongue and makes funny noises whenever I turn my back.

Audio missing in FCP after export

Hi
So I have an audio track in FCP which I sent to STP and added a limiter and reduce noise filter to. Saving it and going back to FCP I notice that 2 seconds are missing from the end of the audio.
I sent the referenced clip with no handles.
Now my sound is out of sync.
Thanks
Joe

Did you do a Send to a Multitrack Project?
STP expects to see 48k audio coming from FCP and send aiff 48k back as an exported file.

Audio missing from saved project

Hi All...
New user here, first-time "test movie" combines video with ambient audio, stills and a music track. Based on Mr. Hunt's article, here's the background information:
Dell Precision T1500 / Windows 7 Professional 64-bit OS, no pen or touch input
Processor: Inter Core i7CPU 870 @ 2.93 GHz
Installed memory: 8 GB
Single hard drive: 930 gb SATA file system, NTFS, compression unchecked / no RAID
"D" drive is HL-DT-ST- DVD+-RW GH50N DVD burner
"E" drive is HL-DT-ST BD-RE BH30N CD ROM drive
No external drives
Virtual memory: 8151 mb dynamically controlled by windows
Video Card: NVDIA QUADRO FX 580 / pci BUS 1 / driver no. 8.17.12.5896, driver date 7-9-2010
Audio System: Realtek high definition audio, 2-channel 16-bit 48000Hz / driver version 6.0.1.5919 / driver date: 8-18-09
Using PE 8.0.1, updated July 14
Project settings: Editing Mode: HD 1080i, timebase 29.97 fps, frame size 1920 x 1080, 16:9 / pixel aspect ratio: square pixels (1.0) / Fields: No Fields (progressive scan) / Display Format 30fps drop-frame timecode / title safe area 20 % / action safe area 10 % audio sample rate: 48000 Hz
Video clips: MPEG movies, image size 1440 x 1080, pixel depth: 32, frame rate 29.97. Average data rate 630-650 KB/second (there are a couple dozen clips, I didn't check them all...)
Source audio format: 48,000 Hz Compresses stereo; project audio format 48,000 Hz 32-bit floating point stereo
Music track: MP3 source audio format: 44,100Hz compressed stereo; project audio format 44,100 Hz 32-bit floating point stereo; average data rate 23KB/sec
Still images: all JPEGs, some 1280 x 960, some 2048 x 1636, pixel depth 32, pixel aspect ratio 1.0.
Other app's typically running: IE and/or Firefox, perhaps MS word and/or Publisher, Mozilla's Thunderbird. However, I've "saved" this project with *no other apps* running, and there's still no audio.
Hope all this suggests a solution...
Thanks for your help, all...
T

Thanks for all this information, T.
So why are you editing a 1440x1080 video in a 1920x1080 project? If this is AVCHD footage, it's very important to use the right project settings.
That has no effect on your audio, of course. But it could affect your video quality when you output your file.
That say, can you explain what you mean by "Audio missing from save project"?
Do you mean that you don't hear the audio in Premiere Elements -- or that you don't hear it when you output, say, an MOV or WMV file?
What file format are you exporting and what are you playing soundless this file on?
And, finally, is there no audio whatsoever, or is only some audio (music, for instance) missing from your output?

Second audio track named as the first, on TV

Hi to everyone,
just finished an Encore project and BR disk plays good and fine.
I've made two tracks (1 italian, 2 english).
Everything works great as mentioned, but if I push the audio botton of the Blue-Ray player remote control, audio changes correctly, TV displays "1 italian" and "2 italian" and not "1 italian" and "2 english" as expected.
Missed something in Encore or is it a BR player matter?
Second audio track in Encore timeline is marked "en".
Thanks
Giorgio

Here is a new,
just finished a DVD project with italian, english and czech (cs) audio track.
Well, it works fine, everything is displayed in the right way, czech track also.
So I tried to modify audio track hierarchy, putting italian as first, then english and czech as third with another empty french track as fourth.
Everything works OK.
So I'm in front of a "crossroad":
- or there is a problem in Blue-Ray (mpeg2) track identification process
- or I have something corrupted in my project, in this way I have to re-build the entire project
Let know in this thread...........LATER!!!!!!
Ciao
Giorgio

Audio missing when shared to QT

Hi,
I've shared a 52minute movie original in iM6HD to QuickTime and on two occasions the audio is completely missing in the resulting .mov (and also a .wmv version I made).
This is a pain as it takes hours to save to QT.
Where am I going wrong, guys?
TT

Your audio settings may have been changed.
1. Open Audio MIDI Setup (/Applications/Utilities/), then check the Audio Output setting.
2. Change the Audio Output setting to 44100.0 Hz.
3. Quit Audio MIDI Setup.
More info here:
http://support.apple.com/kb/HT2178?viewlocale=en_US
More info on audio missing in iMovie here:
http://support.apple.com/kb/TS2289
Alternatively, if the audio was from copy-protected tracks from iTunes, they won't copy over. If that is the case post back for a workaround.

Multi-Take Cycling Audio Missing Revisited...

Apologizes for all the typos in a previous email on the multi-take recording audio missing. I have since done some research and have better terminology to use so I'll restate. I believe this could be a bug and want folks to be aware of it at the very least.
Someone else posted a problem with the "cycle multi-takes" saying that after using pieces of several takes on one track, as done in the instruction video shown in the link below from Apple, his problem was the audio showed up but was not playing at all. I have done the same thing, but the audio just disappeared in 2 out of 10 of my takes, nowhere to be found. It played perfectly while I previewing and deciding what to use, and all takes are still appearing in the drop down list, but when you select them, they are empty. Tried to post a picture of my screen, but can't figure out how to do that!
http://www.apple.com/findouthow/music/garageband08.html#tutorial=multitake
The only thing I did different from the video was to make a new track and copy the multitakes to it, decide what I wanted where and copied it back to the main track after splitting it appropriately.
Thanks to all that offer help on this discussion board!

I believe I have the same problem. When I record multiple takes and then CMND+T to split the track and use different takes, they disappear, re-appear, and sometimes are lost again for good. This is the worst sin a software developer can make--losing a musician's best takes.
I am furious at Apple for this, particularly since Apple Care has consistently claimed ignorance. Apple if you're reading this, you have made a mess of several nights work on several occasions for me. Thanks a lot.

Help needed: audio missing - export to html & pdf

audio missing - export to html & pdf
both soundtrack and audio on specific pages play fine as slideshow and as export Quicktime.
exports to html & pdf are missing audio entirely.
the audio assets are not in the html folder.
i am not doing anything complicated, one .tiff image per page, approx 12mg apiece.
one soundtrack and one additional page specific audio track.
box checked for saving audio files in preferences and while 'saving'.
tried triggering with 'begin audio' builds.
tried different approved formats for audio.
tried different themes. at default settings.
i am out of ideas. any suggestions?
much appreciated.

Sound files are not included in html or pdf exports. There is no way to make it happen. If you need the sound you can export as Quicktime.

Audio missing from video recording.

I recorded some camp footage with a canon rebel T2i. there is audio when i play the clip in imovie timline, but when i export it there are peices of the audio missing. I have removed the clip and re-uploaded it several times and the audio is still missing in the same places. Im not sure if maybe i have the setting wrong or if maybe the file from my camera is corrupted.

Same problem with me and it seems a lot more users. Audio and Video are playing fine in other players and other types of video, everything is connected as it should. You would think that something major like this would not get past quality control before it's being released. I'm getting more and more agitated as there has been absolutely no mention of this from Apple, yet this seems to be a wide spread and major problem. I bought Season 1 of The Office tonight and it is rendered useless because audio won't play, and the DRM limits how you can view your videos.

ATV2 and second audio track

So, for Christmas, I sent out a home video to family, and as a bonus feature included an alternate audio track, which was accessible when playing the video in Quicktime, iTunes, and other i-devices.
I then saw the video played back on an AppleTV2, and to my surprise, it didn't see the alternate audio track at all. Confirmed that on the 'server' machine, iTunes could access the audio track, but when you hold down the 'select' button on the ATV2 remote, there's a tab for 'Audio', but it's grayed out and can't be selected. I also tried using AirPlay to push the video up, and the icon for changing the audio track disappears when you do that.
I tried tinkering around with the video using Subler, but none of my settings I tried were able to make it so that the ATV2 could select between two audio tracks.
Is this possible? The presence of the menu implies that it should be possible, but I haven't found a way to do it. Can anyone tell me what needs to be set or how the audio needs to be encoded?

I'm sure they're not encoded correctly, that's my question, really. How do they need to be encoded and configured?
I've tried the following configurations...
(In Subler there's a checkbox to indicate which audio is played normally, indicated with X for checked, _ for not checked)
1 X Stereo AAC
2 _ Stereo AC3
Defaults to AAC when played on QT or iTunes, ATV2 defaults to the AC3. ATV2 doesn't show track 1 as an option.
1 _ Stereo AAC
2 X Stereo AC3
Defaults to AC3 on all platforms, ATV2 doesn't show track 1 as an option.
1 X Stereo AC3
2 _ Stereo AC3
Defaults to the checked AC3 on all platforms, ATV2 doesn't show track 2 as an option
1 X Stereo AAC
Plays on all platforms
1 X Stereo AC3
Plays on all platforms
So as far as I can tell, ATV2 simply doesn't have support for a second audio track?

Second Audio Track

How can I have Front Row play the second audio track that is part of a video?
-Sgt. Baker

Welcome to the Apple Discussions!
No, I don't think that's possible. Since Front Row really has no user interface for turning on or off an option like that, you won't be able to make that choice. You can, however, play the file with the QuickTime Player application (the current version includes a full screen option without paying for the "Pro" version). Or, if it's a DVD, the DVD Player application gives you full access to all the options.
-Doug

HD video shoot on xdcam, channen 2 audio missing. how can i fix it?

HD video shoot on xdcam, channen 2 audio missing. how can i fix it?

XDCAM, and other codecs like AVCHD, have metadata located in the folders on the memory card. Best practice is to copy ENTIRE contents of card directly over to your hard drive, without using any "transfer utility" software. Then in Premiere, import via the "Media Browser" rather than "File > Import". This gives Premiere the very best chance of correctly figuring out what kind of video and audio assets it is dealing with so it can handle them correctly.
Hope this might help
Thanks
Jeff Pulera
Safe Harbor Computers

Second Audio Devic

I have had an Audigy 2 ZS platinum for quite some time... and it is the coolest thing since sliced bread. I was running Splinter Cell Chaos Theory and some of the audio tracks weren't playing. I ran a dxdiag and to my surprise I found that I had a second audio device installed. This is quite odd for a number of reasons. I have not an onboard sound chip or a modem installed on my computer. Further inspection in the control panel "sounds and audio devices properties" tab showed the audigy AND the "Modem # Line Playback". WTF!? I corrected the problem in Splinter Cell by turning down the acceleration on the dxdiag console... but now in creative wavestudio when you copy and paste a secion of audio... well suffice it to say it is messed up. I turned the acceleration on the "modem line" back up and the problem went away. SO wavestudio is using the modem line as a playback device (even though the menu says it isnt)? The hardware device manager has no flags for conflicting devices... I checked BIOS for the remote possibility I had something onboard enabled (nadda). I am thinking perhaps a total driver uninstall/reinstall. Here is the copied text from my dxdiag. THANK YOU FOR ANY HELP YOU MIGHT BE ABLE TO PROVIDE!
-------------Sound Devices------------- Description: SB Audigy 2 ZS Audio [B800] (emulated) Default Sound Playback: Yes Default Voice Playback: Yes Hardware ID: PCI\VEN_02&DEV_0004&SUBSYS_200202&REV_04 Manufacturer ID: Product ID: 00 Type: Emulated Driver Name: Driver Version: Driver Attributes: WHQL Logo'd: Date and Size: Other Files: Driver Provider: Creative HW Accel Level: Full Cap Flags: 0x2F Min/Max Sample Rate: 00, 00000Static/Strm HW Mix Bufs: 0, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, NoSensaura(tm) ZoomFX(tm): No Registry: OK Sound Test Result: Not run
Description: Modem # Line Playback (emulated) Default Sound Playback: No Default Voice Playback: No Hardware ID: Manufacturer ID: Product ID: 8 Type: Emulated Driver Name: Driver Version: Driver Attributes: WHQL Logo'd: Date and Size: Other Files: Driver Provider: HW Accel Level: Emulation Only Cap Flags: 0x0 Min/Max Sample Rate: 0, 0Static/Strm HW Mix Bufs: 0, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, NoSensaura(tm) ZoomFX(tm): No Registry: OK Sound Test Result: Not run

Yes something is definitely not right B800 is not emulated if you have card, it should be (WDM). I did a dxdiag and do not have modem # showing. Reinstall seems the way to go.

First four seconds of audio missing when exporting project as MPEG2

Hello all-
When I export my project from FCP (using version 6.0.6) using Compressor's (v. 3.0.5) MPEG2 Program Stream setting, everything works fine except for one slight problem: the first four seconds of audio are missing. I've looked back over my timeline (NTSC-DV with 4 tracks of 48khz 16bit audio), everything is fine, and the audio exported just fine using the H.264 codec. I've tried everything I can think of. Any suggestions?
Thanks so much,
Brett

Well I REALLY need some help with this one! I have tried so many different 'work arounds' without success. As mentioned in my first post the audio is not sync'ing with the video when exported. I have tried Exporting the file in QuickTime, I have tried using Compressor again exporting just the video then the audio - pulling it into a new session and lining it up again but everytime I pull it the newly exported file into a new project and render it FCP crashes not allowing it to render (nice!). I actually started from square one capturing the video footage again and assemble the project again without luck. I simply cannot believe what a pain in the arse this is!! I need to get this project done and it simply won't do it.
Where are my blood pressure pills????

30 Second Audio Render problem in Adobe Media Encoder?

I've been trying a few things out to fix this, but no luck.
Ok, so I export videos with a audio spectrums where audio would be necessary. Now I want to do this all in After Effects without editing the Audio in in Premiere Pro. After Effects does not render in H.264. So I send it Adobe Media Encoder. When I export to AME, the first 30 seconds is mute, without fail. only on AME though. I can export straight through AE with .mov and it works fine. but I don't like doing that with the large filesize. I also did this with WebM. Audio does not export for 30 seconds on AME.
I like to send everything to AME. So if I have to go to premiere to fix audio I will. so after fixing everything I send it over to AME and let it export. for some reason, it WILL give me audio. Is there something wrong with my settings in AE or AME?
Everything is CC if that helps any

OK, give this a shot.
FAQ: Why are some codecs and sequence presets missing from my installation of Premiere Pro?

Second audio missing

Similar Messages

Maybe you are looking for