Second display turned off

Hello guys
I plug a 2nd screen (Philips) on my iMac late 2013 (with GTX 780M 4G°) by Minidisplay to HDMI.
It works fine... but, sometimes, when i reboot or start a new session, the display stay off and doesn't appear in the display preferences.
I change the cable, i unplugged and replugged... nothing. Only a reboot (sometimes) or a "Cmd Alt PR" solve the problem.
It worked fine with my late 2009 imac... Any idea ?

Hello there, Zeustef.
The following Knowledge Base article provides some great recommendations for troubleshooting issues with display:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
No video or no signal, image distortion, "snow," or flickering
Check connections
When using an external display be sure to check the following:
If you're using an Apple notebook, confirm the AC power cable or adapter is securely connected to the computer and the cable providing power to the display is also secure. It is always good to have your notebook connected to AC power when an external display is in use.
Confirm display adapters are fully seated in their respective connections and that they are supported models and for the computer and display. Refer to these articles to assist you with adapter compatibility and further configuration information:
Monitor and Display Adapter Table
About Mini DisplayPort to HDMI adapters
Apple Mini DisplayPort adapters: Frequently asked questions (FAQ)
Thunderbolt ports and displays: Frequently asked questions (FAQ)
Remove all display cable extenders, KVM switches, or other like devices and retest to determine if the issue is resolved.
Try unplugging the video adapter or cable and then plug it back in.
If more than one video adapter is in use (or "daisy-chained"), troubleshoot by using only one adapter.
Example: A mini DisplayPort to DVI adapter connected to a DVI to HDMI adapter is an unsupported configuration because there is a series of adapters in use.
If available, try using a different display and or adapter (or use a different connector by using DVI instead of VGA, for instance).
Reset the system
You can reset the Mac's parameter RAM and SMC.Reset the resolutionStart by resetting the Mac's parameter RAM. If the display does not come up, was previously set to an unsupported resolution, and still results in no video:
Start up in Safe Mode.
From the Apple () menu, choose System Preferences.
Choose Displays from the View menu to open the preferences pane.
Select any resolution and refresh rate that your display supports.
Restart your computer.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Similar Messages

Windows 10: Second display "turns off" in lock screen

Unfortunately some of these quirks are why people don't upgrade straight away, on the plus side by having over 14M people upgrade in less than 2 days MS now has a lot of faults found and fixes to work on - quickly. We hope.
That said I have a dual screen setup and my monitors retain the screen space settings.
The fact yours is a laptop maybe indicative of your issue - does your laptop have dual graphics, e.g. one for high use games and one for low use 2D?
Does it turn off 3D settings - it may not be a Windows 10 thing but more of a setting that has defaulted.

I don't recall having this problem with Win 7 Pro, just upgraded to 10 pro a few days ago.I have an HP Probook 450 G2 (with up-to-date graphics driver) and a dual monitor setup. Main display is on HDMI and second display is on VGA. When I lock my laptop (Win+L), it seems to "turn off" the second display and shifts any applications I had in the second display to the main display.While a relatively small issue, it is rather annoying to have to drag applications back over to the second display when I resume working.It doesn't seem to happen right away though, nor does it seem to trigger when display is set to sleep at 20 minutes. I'm not sure how else to explain this. I've found posts of a similar nature on Spiceworks and other forums, but nothing seems to help.Thispostis from a while ago and is related to Win 7, but does seem to describe...
This topic first appeared in the Spiceworks Community

Closing MacBook lid w/ mini-DVI to second display turns off second display

I hooked up a MacBook to another display via the mini-DVI to DVI adapter but, when I close the lid of the MacBook, the other display goes off. The display settings are set to mirror and this doesn't happen with my MacBook Pro. With my MacBook Pro, I can close the lid and continue working with the monitor connected directly to the DVI port without issues. Anyone have any suggestions as, to use my MacBook this way, both displays remain lit which is kind of pointless. Thanks in advance,
Derren.
Black 2 GHz Macbook Mac OS X (10.4.8) 1.5 GB RAM

It is puts the Macbook to sleep when you close the lid.
All you need to do is press a key on the external keyboard or mouse and it will wake up the Macbook with the lid closed. If you are using bluetooth for your external devices, ensure that the "wake from sleep" option is enabled under Bluetooth setting in System Preferences.

External display turns off when macbook isn't charging...

I have my old 2007 white Macbook hooked up to an external display. Recently I have been wanting to calibrate the battery while using it on the external display, but every time I remove the charger from the Macbook the external display will stay on for a couple of seconds then turn off, it will only come back on when I click the mouse or press something on the keyboard, but then it will go back to sleep. Note: when my Macbook is connected to the external display I keep the screen closed.

When you are looking at the displays in the System Prefs, all you have to do is click and drag the tiny rectangular bar from the main screen to the external monitor screen (this designates the primary monitor).
Once you've done that, all you have to do is close the lid. Your screen will flash a couple times, but the external monitor will then remain on and working, and you dont need to keep your lid open.
FYI, I would turn down the brightness of your MBP down all the way (for both the screen and keyboard). I have found that this reduces any heat build up that it may have from running with a closed lid.
Hope this helps!
Ben

White Stripes/Display Turning Off

Last night I noticed a bunch of white stripes flicker for about a quarter of a second on my display. This happened multiple times. I shut it down with no problems.
Today I had no problems until everything froze. I could move the mouse, but it would not change from a text cursor. I manually shut it down.
I turned it back on, after a few minutes I had the same issue.
I turned it off manually, unplugged the power for about a minute, plugged it back in and turned it on. After a few minutes the white stripes flickered. I decided to back up everything. After about 10 minutes, during the backup process, the screen went black. I could feel that the computer was still on, but the display was black. I manually turned it off.
I have now been on for about 30 minutes with no problems. The computer was very hot when the display went black. Is it possible that this is an overheating problem?
Any suggestions?

The iBook has a seperate display dimming (display turns off) and sleep mode timers. Go into the system preferences>energy saver to set these preferences. When your display turns off you should be able to reawaken it by pressing a key on the keyboard. Turning it off is not the best solution. If the problem happens while you are still using it or it doesn't awaken when you hit a key then you may need to post here again.

L305D-S5935 Unresponsive After Display Turns Off

I have a L305D-S5935 running Windows Vista and it becomes unresponsive after the display turns off as set to do so in the power settings. I cannot push any key or button or move around on the mouse pad to get it to turn back on. This is very frustrating and the only way to get it to come back on is to to a hard restart.

Turn off your laptop, unplug all wires, remove the battery, and hold the power button for thirty seconds. Afterwards, reattach the battery and connections.
Then reinstall TVAP.
Toshiba Value Added Package for Windows Vista/7 (32)(v1.2.33; 11-09-2009; 43.67M)
- Peter

T42 Display turns off after moving

Hello everybody!
I´ve got a problem with my Thinkpad T42 (2373fwg), XP prof. with the latest updates running. After installing the latest drivers for display (ati) and for "ThinkVantage Active Protection System " the display turns off immediately after moving the Thinkpad. I can turn the display on again only by reboot. The error appears even in a second after reboot, so it doesn´t concern to windows. The system doesn´t crash, it´s only the display. The problem might concern to the shock sensor, but I don´t know how to solve it.
Does anyone of you has an idea?
Thank you and kind regards
Bill
Message Edited by billyflinn on 01-26-2009 09:29 AM

I have a similar problem: T42 (2373-5wg) Screen blanks. At first screen blanking was rare and seemed to happen when moving the pc, but now the screen blanks within 1-3 minutes after turning on the laptop, even if the computer is left untouched after being turned on.
It is not OS related as the blanking appears even when in BIOS setup or booted on a liveOS CD.
I can't tell for sure if the system crashes or not as the display goes blank (doh!), however, I have seen no reports of registered crashes in the visible part of the boot process.
The screen blanking appears quicker (or even instantly) if the computer is warm (e.g. turned off just before being turned on).
Blanking appears simultaneously on the LCD and on any attached external monitor, so I believe this rules out a defective LCD, backlight or inverter board.
I'm thinking it's a failing graphics adapter or system board, or maybe a loose connection that causes a component to overheat and fail. But I don't know which or how to fix it.
It IS out of warranty, of course. Any ideas?
Thanks in advance,
Niels
EDIT: It seems this could be yet another case of badly soldered BGA chips that seems to be troubling the T4x series:
http://forum.thinkpads.com/viewtopic.php?f=2&t=33952&sid=99545e4d13d9a94ce7496a5022690ed8&start=30
http://www.technotaste.com/blog/thinkpad-t42-ati-radeon-9600-driver-and-the-blue-screen-of-death-bso...
Message Edited by NielsCN on 01-26-2009 12:11 PM
Message Edited by NielsCN on 01-26-2009 02:25 PM

Display Turns Off After Opening Computer

I have a very annoying problem of my display turning off and not turning on until I restart my Macbook Pro by holding down the power button.
For example, I will close my computer (power cord not plugged in) and it will go to sleep. If for some reason the computer turns on while it is still closed (this happens when I pick it up/move it around sometimes) and I then open the computer, the display will be on momentarily and then turn off leaving me with a black screen. The only way to turn the display on again is to restart my computer.
Another example: I might close the computer with the power cord in. I will then unplug the computer (still closed) and walk somewhere, then open the computer. The display will be on for a few seconds and then turn off, leaving me again to restart my computer.
The third example is the worst. Sometimes with the power cord still in, sometimes with no power cord, the display will just be blank when I open the computer.
With all of the above occurrences, I know the computer is running because I can see the caps lock key light change when I press it.
Does this make any sense? Please help me, I will be going to college on Tuesday and I would really like to have it so I don't have to restart my computer every time before class.
My display was not always this way, it has just been like this for a few months.

Im surfing this kinda of problemes. Its insteresting your computer turn on the screen after restart, but there no much good news for us in here: http://discussions.apple.com/thread.jspa?threadID=1478474&tstart=0

When I try powering up my phone it stays on the logo screen for a few seconds then turn off, whats wrong with it?

When I try to power up my iphone 4 32g, it will stay on the apple screen for a few seconds then turn off. even when I try connecting it to my computer it turns on for a few seconds then turns off. Whats wrong with it? and what do I do about it?

Have you tried charging it with another known working USB sync cable? After letting it sit to "charge" for at least 30 minutes, have you tried resetting the device by pressing and holding both the Select/Center and Menu buttons together long enough for the Apple logo to appear.
B-rock

In my ipad mini sound is there but somehow display turned off....please help...how to turn on the display

In my ipad mini sound is there but somehow display turned off....please help...how to turn on the display

Frozen or unresponsive iPad
Resolve these most common issues:
    •    Display remains black or blank
    •    Touch screen not responding
    •    Application unexpectedly closes or freezes
http://www.apple.com/support/ipad/assistant/ipad/
iPad Frozen, not responding, how to fix
http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
Black or Blank Screen on iPad or iPhone
http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
Home button not working or unresponsive, fix
http://appletoolbox.com/2013/04/home-button-not-working-or-unresponsive-fix/
Fixing an iPad Home Button
http://tinyurl.com/om6rd6u
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
 Cheers, Tom

Yoga display turns off after 1 minute

I'm having an annoying problem with my new Yoga related to the display and have not seen any other posts with a similar complaint so perhaps this is a simple fix that I'm just not able to sort out on my own. My display turns off after 1 minute of inactivity. The only means for changing behavior like this that I am aware of is through the Control Panel Power Options. My settings for "turn off the display" are 10 minutes on battery and Never while plugged in (note screen shot attached). Regardless of my settings, the screen turns off after 1 minute. I've changed the settings to multiple configurations and restarted with no change in behavior. Perhaps there's some other settings area, maybe something specific to Lenovo that I'm not aware of (since this is my first Lenovo laptop). Anyone with similar problems or insight?

This may be a Windows 8 issue. I finally fixed this problem by identifying the screen saver as the issue (and I wasn't using a screen saver). Type "lock the computer" into the search box after clicking the search charm, which brings up the screen saver dialog box. Mine was set to 1 minute, though I'd never set it myself. If you can't change it, choose a screen saver and you should be able to do so (and can then switch back to no screen saver). BUT, here's the problem. Other things you install (or settings within things you install) can apparently change and override whatever you type in for the delay time. Try applying your new time and exiting from the dialog box, then open it back up again. I was finding that it kept going back to 1 minute. To reset things so that you can get control again, type "user accounts" into the search box and when the dialog box comes up, choose "Reset Security Policies". Then you can go back to the screen saver dialog and successfully change the delay time. See http://social.technet.microsoft.com/Forums/windows/en-us/ace4085a-b0ba-4a98-898d-cd92d9e88e13/window... for some detail.

W520 - now changes to "projector only" whenever display turns off in power save mode

I have my W520 in a dock with an external monitor. The display is configured to Extend - the external monitor is primary, and the desktop extends onto the W520 screen. I don't have a screen saver. I turn off the display after 30 minutes of inactivity. Until recently both the laptop and monitor screens would turn off after 30 minutes, and then both resume when I moved the mouse or pressed a key.
Recently, the system has started changing to "Projector Only" when the display turns off. After resuming from power save mode, only the external monitor activates, and the W520 screen is disabled. I have to use Fn-F6 to switch back to "Extend" to re-activate the laptop screen.
I have rebooted and re-saved the power plan.
Why has this happened, and how do I fix it?

Hi, timg11
I have a few questions so that I may gain a better grasp of this issue:
1) What is your machine type and model? You can find this information on the bottom of your machine. It should be in format XXXX-XXX.
2) What is your operating system?
3) Does this issue occur is the computer is not in the docking station? (Please try if you haven't already).
Thanks in advance,
Adam
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it.

Did the most recent update and now my TB Display turns off randomly on both my air and mini. I running TB Firmware Version: 23.6

did the most recent update and now my TB Display turns off randomly on both my air and mini. I running TB Firmware Version:
23.6

When did you get this firmware version? My TBD is at 22.2 and the TBD bus is at 23.4. I thought I had the latest firmware.

I'm trying to use a madcatz controller on the mac but it turns on for 2 seconds and turns off. the system profiler picks it up as a xbox 360 gamepad but says its not been configured. how can i allow my self use this with my games.

i'm trying to use a madcatz controller on the mac but it turns on for 2 seconds and turns off. the system profiler picks it up as a xbox 360 gamepad but says its not been configured. how can i allow my self use this with my games!

I have exactly the same problem.
I'm a little peed-off with Microsoft on this. The original wireless controller I have doesn't work either since the cable I'm using is 'just' the charge and play cable, so a direct connection to my Mac won't work with this cable. It's a cable for god's sake. Why on EARTH put any limitations on this!?!?
Next I learn I need an additional USB wireless receiver from Microsoft to get my original 360 controller to talk to my Mac. As I certainly don't want to fork any more microsoft dollars on this, this is not an option.
Next I think, yes! I have a MadCatz 360 wired USB controller. This should surely do the trick just plugging it in and the way I go. But oh no, for some reason I plug my MadCatz Xbox360 controller in, it flashes a few times then switches off and can't be turned on again.
The System Profiles recognizes it as a MadCatz 360 device controller but that is about it, but the ontroller software I download for the System Prefs (360Controller, USBOverdrive etc) don't even recognize the controller as being plugged in.
What the **** Is The Microsoft Deal with all of this!?!?
PS: Oh, and I forgot to mention, there are No drivers for device 4716 that I can find on the MadCatz website, or am I going blind?
If anyone has a link, it would be appreciated.
Message was edited by: nostrawaggus

Installed runs for 10 seconds then turns off continues doin it

i installed firefox 4 it runs for about 10 seconds then turns off i re apply the programe thing runs a short while then turns off i have re installed from different sites several times still no joy

Which PowerMac is experiencing the issue ? (It's a powermac forum)
Which Mac OS ?
and which AirPort software version ? (use Get Info on AirPort Utility)
Which encryption method are you using on the Mac ? (it's been known to get it wrong)
ie. WEP 40-bit, WEP 128-bit, WPA, WPA2, WPA2 Personal (open Network Prefs, select AirPort and click Advanced).
Which encryption method are you using on the WiFi network ? Be exact.
There's a big difference between WPA, WPA2 and WPA2 Personal (and a few others).
Does the WiFi device have any filtering on it ? That could be anything from MAC address filtering to only using the wireless N protocol, which may xclude your wireless G (or wireless B) PowerMac.

Second display turned off

Similar Messages

Maybe you are looking for