Secure boot not working with MSI Z77a-G45 And system reserve not showing

Ok so i re did my windows after i did a zero fill on my hard drive as it was showing a corrupted sector on my disk that seemed to fix it for now, until it comes back if it does crossing my fingers it gone for good. But now i can't seem to get Secure boot to work i mean i did not have it before as i just slapped the motherboard in with a existing windows, that was to be expected but this is a clean install of windows 8.1 and i even have secure boot on but its not working and reports as off in windows. Is it because i have my bios set to legacy+UEFI??? would that make secure boot not work??. i even went as far as turning it off and back on again the secure boot setting nothing made a difference. I mean its not a big deal bit would be nice to know why its not working, also another wired thing and i will post pictures of it, as i cant see my system reserved partition in disk management but diskpart says it there, i will post those pictures any ideas??.

fixed it is my legacy+uefi another forum got back to me.

Similar Messages

Wifi not working with iTunes, apps store and some, but not all Internet sites....why???

Yesterday I noticed while browsing Internet that some sites would not open and that some games I regularly play would not open. I also found that I could not open either the apps store or iTunes. Everything seemed to be working the day before and I have not recently upgraded ios (been on version 6.1.3 for a while) or changed any settings on my iPad (2). With Internet research today I found suggestion that if I switched to 3G I would be able to access these apps and,sure enough, under 3G connection everything works fine. Some other forums suggest changing wifi router settings to fix the issue ....I have not tried this as I wouldn't like to mess with my router and end up effecting other peripherals/pc's connected to it that are working fine....especially when I am not terribly IT savvy when it comes to hardware settings. But as I haven't changed anything on my ipad why would my wifi suddenly stop connecting to some apps on my iPad, but not all??? Interestingly I can access many Internet sites (forums) with wifi connection but not the apple forum! To get to anything apple related I have to switch back to 3G ....that includes checking the iOS version I am on via settings!
I also mention that I have done all the other suggested fixes found on various forums, such as rebooting iPad, renewing wifi lease, clearing cookies, closing all apps etc etc, to no avail. Seems the only suggested fix I have not tried is mucking around with my router which I am very hesitant to do given the **** I went through with my telco when my home Internet connection suddenly stopped working last year. Took me weeks of phone calls to get my internet connection back and being forced by the telco to a more expensive plan, hence very reluctant to start mucking around with that side of things, but why should I need to when it does seem to be working ok with other devices in the home?
I have started this as new discussion as, even though I am not terribly IT savvy, I cant see how this could be related to the wifi issues that many on the newer devices (iPhone 5 and iPad mini etc) are reporting as I haven't recently upgraded anything on my ipad and all was working perfectly up until yesterday.
Any other suggestions on how to get wifi working correctly again on iPad or do I really have to risk the working of every other device in my home and chase it from modem/router side?

Hi there,
You mentioned that you have tried a few troubleshooting steps already, but you may want to take a look at the article below, specifically the section titled "If you are unable to access the Internet while connected to a Wi-Fi network"
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
Hope that helps,
Griff W.

Mail app not working with iCloud, new emails and recently sent not showing at all in the app.

I've been using the iCloud mail for quite some time now

A lot of people have been unable to access Yahoo e-mail on their iPhones or iPads. My wife’s iPad was not downloading Yahoo mail, although her iPhone was. Both used IOS 8.2. We tried deleting the account several times and troubleshooting all of the other settings. The problem appears to have been that allowing the IOS to automatically create the account on the iPad resulted in the wrong settings for the incoming server. The following procedure, pieced together from two websites, fixed the problem for us. So far, so good.
https://portal.smartertools.com/kb/a2659/configure-imap-for-iphone-or-ipad.aspx
https://help.yahoo.com/kb/mobile-mail/imap-server-settings-sln4075.html
On the iPhone, tap Settings.
Tap Mail, Contacts, Calendars.
Tap your Yahoo account, then delete it.
Tap Add Account.
Tap Other.
Tap Add Mail Account.
Complete the Name, Address (email address), Password and Description fields.
Click Next.
Ensure IMAP is selected.
Enter the following incoming mail server information:
Incoming Mail (IMAP) Server - Requires SSL
Server: imap.mail.yahoo.com
Port: 993
Requires SSL: Yes
Hostname is mail.yahoo.com.
Username is your full email address
Password is the same password used to access webmail.
Enter the following outgoing mail server information:
Outgoing Mail (SMTP) Server - Requires SSL
Server: smtp.mail.yahoo.com
Port: 465 or 587
Requires SSL: Yes
Requires authentication: Yes
Username is your full email address
Password is the same password used to access webmail. It may have been entered for you.
Tap Next.
The iPhone will establish an SSL connection to your IMAP and SMTP servers.
That’s all!

Lync Server 2010 conference not working with Windows 8.1 and IE 10

Hello,
The problem is that whenever a Windows 8.1 user tries to join a Lync server 2010 conference using Internet Explorer 10 (or 11, tried that too) the user can't join the conference. If the conference is created by a Lync server 2013 user joining works fine.
When using Lync 2010 client we get the following error in the client: "error id 87 source id 7".
When using Lync 2013 client we end up with a blank conversation window.
There are no traces in server log, client log or event log.
Below is a set of use cases that may help you to understand what is the problem scenario. Each of these works or does not work with both Lync 2010 and Lync 2013 client.
- Lync server 2010 conference, windows 7, Chrome, Firefox, IE 10 or 11 --> Works.
- Lync server 2010 conference, windows 8.1, IE 10 or 11 --> Does not work.
- Lync server 2010 conference, windows 8.1, Chrome or Firefox --> Works.
- Lync server 2013 conference, windows 8.1, Chrome, Firefox, IE 10 or 11 --> Works.
It does not help to add the meet address to IE compatibility list (Compatibility View Settings).
If i press F12 in IE and change the document mode of the meet page to IE 9 version then i can join meetings with Windows 8.1 and IE 10. Unfortunately i cannot make that as a default setting for the meet website.
Any ideas on how to get Lync server 2010 meetings working with Windows 8.1 and IE 10 or 11?
IE is the company default browser. Windows 8.1 is not a default operating system but we have increasing number of Windows 8.1 computers in our environment (mainly directors).

According to your description, it is hard to tell whether the issue is related with IE or Lync Server 2010 or both.
Compare the log when Lync client on Window 8.1 with IE 10 or IE 11 join Lync server 2010 conferencing and Lync Server 2013 conferencing.
Lisa Zheng
TechNet Community Support

I keep trying to download Photoshop CS3 and a get a 404 error page, does Photoshop CS3 not working with a new Mac operating system?

I keep trying to download Photoshop CS3 and a get a 404 error page, does Photoshop CS3 not working with a new Mac operating system?

you must also use a browser that allows cookies. try a different browser or download from adobe.com
Downloads available:
Suites and Programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4 | CS3
Acrobat: XI, X | 9,8 | 9 standard
Premiere Elements: 12 | 11, 10 | 9, 8, 7
Photoshop Elements: 12 | 11, 10 | 9,8,7
Lightroom: 5.5 (win), 5.5 (mac) | 5.4 (win), 5.4 (mac) | 5 | 4 | 3
Captivate: 8 | 7 | 6 | 5
Contribute: CS5 | CS4, CS3
Download and installation help for Adobe links
Download and installation help for Prodesigntools links are listed on most linked pages. They are critical; especially steps 1, 2 and 3. If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'.

My imsg is not working with only one person and her imsg is working perfectly fine with her friends

My imsg is not working with only one person and her imsg is working perfectly fine with her friends

See this thread:
https://discussions.apple.com/thread/5306216?tstart=0
From Apple:
MacBook Air (Mid 2013): FaceTime HD Camera might not work after OS X 10.8.5 update
Yes, a fix is coming soon.

TS1365 My Mac book pre suddenly got power off meanwhile it was fully charged. I tried to turn on but it's not working. I reconnected charger and the green light showing with blinking.

My Mac book pre suddenly got power off meanwhile it was fully charged. I tried to turn on but it's not working. I reconnected charger and the green light showing with blinking. How can I fix it?

cooldedar wrote:
I reconnected charger and the green light showing with blinking.
Well the blinking light shows it's charging, however just to make sure.
Reset the SMC, then connect the machine to a power source that doesn't have a lot of other power items on the same lines (in the walls) in the same room and see how it is in the morning.
For instance use a powerline in another spare room that isn't being used as much.
https://support.apple.com/kb/HT3964

Three beeps when booting new computer with MSI Z77A-G43 Mobo

I just built this pc and pressed the power button. Nothing happens for a few seconds and then I hear 3 beeps from the PC speaker. It powers off by itself and opens again, with 3 beeps again, and repeats this until i press the power button to close it down forcefully.
Board: MSI Z77A-G43
Bios: I am not sure, but the box says Click BIOS II
VGA: MSI 7850 Twin Frozr III
PSU: Corsair Builder 600W 80 PLUS Bronze Certified ATX12V Power Supply
CPU: Intel Core i5-3570K 3.4GHz Quad-Core Processor LGA 1155
MEM: Corsair
HDD: 1 TB Western Digital Caviar Black
COOLER: CoolMaster Hyper 212 EVO
OC: none

3 beeps is a memory failure!
try each stick in slot 2 individually as you may possibly have a bad stick?
if the first suggestion doesn't work remove the CPU and check the socket as you may have a bent pin in there causing the issue?

MSI Z77A-G45 and Samsung 840 Series weirdness

Ok so here's the thing
about a week ago i decided that it was time to build a new computer with a Z77A-G45 motherboard
put it together, installed windows 7 64-bit and everything was working just fine - for about 5 days -
but then one morning when i turned on my computer it decided not to boot and just sat there with fans running with an A2 code at the bottom left of the screen
i tried taking out the ram leaving just 1 in and moving it to different slots and trying a different ram block boots thinking it might be faulty ram,
when that didn't work i tried removing the graphics card and boot with just the onboard VGA, reset the CMOS jumper, and even replaced that battery on the motherboard thinking the shop might have shipped an almost dead one, took everything apart and booted it outside the case on a glass surface to make sure it wasn't some sort of short
but the only time it actually wanted to get past the A2 code was when i booted with only 1 of my hard drives, so i started changing my drives around using various combinations of SATA cables and ports (luckily had an extra 5 SATA cables lying around)
eventually i narrowed it down to it wanting to boot with 2 of my 3 drives but the 3rd one (a Samsung 840 series 500 GB SSD, that has no system files or anything fancy other then music, movies and a few games at the moment) getting it stuck on the A2 code
so i set it up as an external USB drive with a SATA/USB converter i had sitting around but then it would get stuck on B4 instead if i booted with the drive connected
however everything would work just fine if i connected the drive after the system had booted up (or even just unplugging and replugging it when it got stuck on the B4)
once back in windows with the drive connected i ran all the diagnostics i could think of but nothing showed anything wrong with it
(and the only thing i had done with the drive before it stopped wanting to boot was to defrag it)
eventually i decided to copy all the files from the drive to a different drive and reformat it as sort of a hail-mary
and to my surprise that actually made it boot up just fine
so i moved it back inside the case as a normal drive just to make sure it would still work (which it did) and then moved all the files back to see if any of them were the culprit - that turned out not to be the case however
it booted up without complaint with all the original files on it
so now my question is why?
what the heck is going on?
did defragging cause some sort of data fault that caused the bios to not be able to read the drive properly or did i just buy a haunted computer?
like i said everything is back in the state it was the day before it didn't want to boot and bios and been defaulted so it's not really an issue at the moment but I'd still like to know what's going on so i can hopefully avoid it in the future
any answers or comments will be appreciated
for your reference a full parts list:
Motherboard: MSI Z77A-G45
Bios Version: 2.10
Graphics card: Club3D GeForce GTX 550ti 2GB
PSU: Corsair TX 950W - 100-240V ~ 12A 50/60Hz
CPU: Intel Core i7 3770K / 3.5 GHz Processor (Stock boxed fan)
RAM: Corsair Vengeance - 32 GB (4 x 8 GB) - DIMM 240-pin - DDR3 - 1600 MHz ( PC3-12800 )
HDD: OCZ-Vertex2 128GB SSD (OS)
Hitachi HDS722020ALA330 2TB HDD (Media/Backup)
Samsung 840 Series 500GB SSD (Media/Backup)
OS: Windows 7 64bit Ultimate

This is strange
I have Z77A-G43, and have exactly the same problem with one 1GB sata drive, that works just fine in every other PC.
In my case PC run into restart loop, but with same code A2 as yours.
Strangest part was PC was restarting even if I put HDD into PCI Sata/Raid card !?
So I am guessing here its not a hardware problem, but a software (BIOS) problem.
Now whole pc with Z77A-G43 is at Service because of faulty DVI output (not working).
Will try reformating drive, but need first to buy >1gb hdd to backup that one
Drive is currently working just fine in this 10y old MSI PC =.=
It seams they have stopped making things as they used to, this old mb is one durrable dog.
which was the main reason I went to same company when in question was mb...

HT1430 my iphone 4 has suddenly ceased to work with a full battery and switch will not display slider. How can I reactivate it?

My iphone 4 has suddenly ceased to operate with a full battery and switch will not display slider. How can I reactivate it? Is the memory gone? Will T Mobile replace the memory or the phone if necessary?

Hello,
If you're in a country where there's an apple shop (unfortunately not mine), go check it and ask the employee about it: he's gonna check your Iphone on a "device"
I've got an iphone 5 and it's working very well with me but I have to admit that its battery lasts (slower) than my Ipad 2.
Still i can help with some tips that may improve your iohone's battery by an hour in addition (hopefully):
- close all apps by multitasking....
- do NOT keep the brightness to the max
Believe me you're gonna regret changing your phone to a samsung
Hope i've helped and sorry for my bad english (has english as 3rd language)

The expand on Youtube is not working with many Youtube sites and they work on Internet Explorer

On many of the sites on Youtube the expand does not work with Mozilla Firefox 4. I have gone to Internet Explorer and they work there. When I come back from Internet Explorer strange enough the expand on Firefox works. Obviously its picking up programming from Internet Explorer, unfortunately it does not last long. I've tried plug ins, reloading flash player after I deleted it and re-installed it, the problem still exist. Also on the expand screens that do work on the right side there is a very thin white line coming down the border. I'm not the only one with this problem. please help with this problem.

Indeed, this is a bug in HTTPS-everywhere which you can see here : https://trac.torproject.org/projects/tor/ticket/4032

My sound is not working with the computer speakers and with headphones, help?!

my sound is not working with my headphones or the the computer speakers

You indicate you have a "brand new Air", you have a 14 day exchange, and the warranty of which you paid for regarding genius bar in-shop diagnostics (and repair if necessary)
What year model Air do you have?
On the first question,....are the headphones attached when you have your Air in sleep?
If yes, then refrain from having phones attached when you close the monitor to prevent this until it is resolved
resolution as to same yet, no.

MSI GTX 970 not working on MSI z77a-gd65

The screen only shows a underline in the superior left, lights on, fans on, old vga "MSI GTX 560ti" works normally.
PC specs.
MSI z77a-GD65(MS-7751)
Intel i53570k
PSU Seasonic 520w model ss520gb active pfc f3 80plus

Quote from: Svet on 19-March-15, 04:53:06
have you done a >>Clear CMOS Guide<< with power cord removed?
what is the mainboard bios version used?
this mean top left or?
any boot codes?
I updated the bios, its working now, thanks for the reply.

Need some help with MSI Z77A-G45 Gaming Motherboard

Hey guys I want to buy the z77a-g45 gaming Motherboard.
but i dont now if i could use my RAM that i own now. could you help me out.
My ram is: Corsair Vengeance CMZ16GX3M4A1600C9 4x4GB

As said before:
Quote from: flobelix on 21-October-13, 04:11:33
None the less that Corsair kit should work although a 4x4GB kit is not optimal for a dual channel system (as 2x4 or 2x8GB would be ideal). That matched 1.5V kit should none the less work.

Flash CS4 not working with Windows 7 64bit and Kaspersky Internet Security

I have a new i5 core computer running Windows 7 64bit retail. With Kaspersky Internet Security 2010 installed Flash CS4 becomes so unresponsive that it is completely unusable. Uninstall KIS and it works absolutely fine. I've already read on another forum that someone else is experiencing the same issue with the same combination of products. Is anyone else having this problem amd if so how did you solve it? I've posted on the Kaspersky forum with no solution thus far.
Does Norton work OK with Windows 7(64) and CS4?

*** PROBLEM SOLVED ***
Taxxem you are a star. Ideed turning off 'disable external service control' and disabling 'self defense' under 'settings -options' does indeed bring Flash back to life. Disabling self-defense had the most impact (and causes Kaspersky to grumble somewhat) but disabling external service control also had an impact, albeit much smaller. I'll post this solution against my Kaspersky forum post and hopefully they will do something about it.

Secure boot not working with MSI Z77a-G45 And system reserve not showing

Similar Messages

Maybe you are looking for