Secure easy setup button on wrt54g v8

where can I find an explanation of what this button does and how it can help me print wirelessly to my HL-2070N brother printer.
What appears to happen when I press button is it flashes for a little while not long and then stops and remains lit.
What does that mean and what is it doing? I still cannot print to my 2070N

Okay Linksys understands there are dolt like me out here who can't figure out how to configure so this magic button is suppose to press at same time as something at http://192.168.1.1 except when I try to go to link I get The connection has timed out The server at 192.168.1.1 is taking too long to respond. * The site could be temporarily unavailable or too busy. Try again in a few moments. * If you are unable to load any pages, check your computer's network connection. * If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. Any suggestions would be appreciated.

Similar Messages

  • Secure Easy Setup Help WRT54GS

    Hi,
    Was wondering what it means when the Secure Easy Setup button on the router remains white.. It usually goes to yellow after the flashing, but this time it remains white...
    Everything seems to be fine on the wireless network, it's just not going back to yellow for some reason...
    I've tried pressing it again, but there is no change.....
    Any input would be greatly appreciated!!
    Thanks,
    JP
    Message Edited by ICE468 on 04-27-200705:23 PM

    That means the SES feature of your router is active. Your router wireless settings are randomly generated by the router and not personalized. For example, your wireless network name (SSID) might be linksys_SES_187498 ......

  • Can someone explain why the Secure Easy Setup light on a...

    Can someone explain why the Secure Easy Setup light on a WRT54G would change from a steady green to steady orange after firmware upgrade?  Everything is connecting properly, and I see no change in performance of network other than light change described.   Thanks. 

    The way I understand the Secure Easy Setup button is this.
    It will be orange when the router is in normal operation mode. The light turns green when you press the Cisco Systems button (that is orange normally) so that the router will search for the web device you are trying to connect to the router. If you want to disable this feature all together go into your router settings page at 192.168.1.1
    Go to the Wireless tab, and then the Advanced Wireless Settings sub-heading, once in there look for the option SecureEasysetup and simply set it to disable (enabled is default) then click the save now and apply the settings. The light should be out now meaning you don't have the Secure Setup feature enabled.
    It is just a personal choice to have it on or off, it should not affect router or internet performance unless you hit the button trying to connect a device to the network.
    Message Edited by MontanaXVI on 12-14-2007 07:12 PM

  • Secure-Easy-Setup Error?

    What happened was that when to go powercycle my router, I accidently pressed the Secure-Easy-Setup button. 3 seconds after I had un-pluged the router, I realized that I had had my hand on the button and was pressing it. I quickly let go and pluged my router back in. It still runs, but now I can't acess the internet on any of my computers. My iPod shows that a new network is present, but I strongly believe that it is my network, but reconfigured and renamed.
    What do I do to fix this?
    It is a:
    (Linksys/Cisco)
    Wireless-G
    Broadband Router
    Model: WRT54GL (EU)

    Press and hold the reset button in back for 30 seconds and release.  Wait 30 seconds and power cycle the router.  Connect via a wired computer to 192.168.1.1 username blank, password 'admin'.  Reconfigure your router back.

  • Added a scanner with Secure Easy Setup and my wireless network has disappeared?

    I just replaced my fax/scanner.  I have a secured wireless home network.  I installed the fax/scanner with Secure Easy Setup.  The fax works - but my home network as disappeared!!!  Where did it go?  Do I have to start over and reinstall my whole wireless network?  It took me forever to get it working the first time!  HELP!!!

    when u run easilink again it will give you the chance to change some settings wirelessly, it could be that you have changed some settings and missed that part...
    you could check that by accessing the set up page of the router 192.168.1.1

  • Wrt54gs & secure easy setup.

    For some time I had problems getting my router to see my WUSB54GS but after a couple of months  laying in the wardrobe I decided to dust it down and try again.
    reluctantly after a few hours it gave up and let me connect my two PCs together.  HAPPY DAYS.  The Internet was a bit slow on the second PC but it was working.  this PC could see and view the shared folders on the other but alas it couldnt see this one.
    I persisted until this morning when suddenly the 2nd PC could not connect.  I tried everything but it could see 3 or 4 other networks but not it's own.
    I eventually traced it down to the fact that the SSID was changed and the encryption method and key.  How did it change overnight with both PCs off?
    I ended up running the installation software again but when it asked for easy secure to be pressed then the lights all flashed, the yellow LED went out and now refuses to come on again!  the USB device says that the easy secure is not available.
    What have I done?  I'm used to working on PCs but networking is relatively new to me.  Switching firewalls off only reduced the internet to an absolute crawl and they still couldnt see each other.  all I wanted was a wifi connection to allow me to transfer files between PCs and maybe even run a LAN to game with but it's getting so difficult that I'm once again thinking of the wardrobe again or better still eBay.
    TIA.
    Robin

    That means the SES feature of your router is active. Your router wireless settings are randomly generated by the router and not personalized. For example, your wireless network name (SSID) might be linksys_SES_187498 ......

  • Since updating to Firefox 4.0.1 I have lost the Easy Edit button on my Wetpaint Wiki. How can I remove 4.0.1 and return to previous verison?

    The Wetpaint Wiki worked well with previous version of Firefox but doesn't work now. I can load wiki but it appears different to normal and the Easy Edit button no longer exists. I want to get rid of the new Firefox and go back to old one. How can I do this please?

    http://community.norton.com/t5/Norton-Internet-Security-Norton/Norton-Toolbar-not-compatible-with-FF-4-0-1/td-p/442788

  • E2000 won't connect to laptop using Easy Setup Key

    Running Win7. When trying to connect Lenovo laptop to E2000 with Easy Setup Key, the progress bar hangs at 25%. However, the E2000 will connect to the laptop with an Ethernet cable. Same problem on both of my Lenovo G555 laptops. Any ideas?

    I have heard about this concern with Atheros adapters and where it cannot connect with WPA or WPA2. Check if you set the security to WEP if it will connect. (Usually it does). And better check for updated drivers from this website. http://www.atheros.cz/ (manually update the drivers). The automatic update with windows will most of the time load the same driver version. So it would be best to update the drivers manually.

  • Loading New Easy Setups in Final Cut Pro 5

    I want to load the extra easy setups for the sequences in Final Cut Pro. Specifically I need to 24p presets. I have located the files but can anyone help me with a tip on how to get these .fcpre files into the program?
    Thanks for any reply!
    G
    G5   Mac OS X (10.4.6)  

    They are all there.
    When you create a sequence, click on the settings menu choice and elect to load preset.
    On launch, there is a "show all" button you can check.

  • TP 600X Always Boots to Easy-Setup

    Hello...
    It's a 600X 2646-D3U. BIOS is BIOS ITET55WW, 11/30/99
    I bought it used in 2004 and it has served two kids reasonably well. They've moved on to more current hardware and I'm trying to bring it back to life. 
    I replaced the 'button' battery, the li-Ion battery and the keyboard. It had/is been running WXP for a few years. But...
    No matter what I do, it always boots to the Easy-Setup screen. I've gone through all the options there and confirm/reset the config & boot options.
    If I then select 'Restart', it comes back to the Easy-Setup screen. If I just press ctrl+alt+del from the Easy-Setup screen it boots to WXP and the Windows Logon screen.
    It's almost like the F1 key is stuck down during power-on. There are no indications that the F1 key is not working correctly.
    Any suggestions/help would be appreciated. Thanks.

    I believe that a stuck F1 key is about the only one you can have stuck on the keyboard and still be able to boot into Windows.  I just duplicated your problem with one of my 600X systems by continuously pressing the F1 key and booting.  It goes right into the Easy-Setup menu and then Windows after the CTRL-ALT-DEL, while still holding onto the F1 key.  The F1 key is typically used by Windows programs to bring up a Help window. For example, if Firefox (3.5) is running, pressing the F1 key will open a tab at the support page; Internet Explorer opens up a popup Help utility.
    You can verify the functioning of all of the keyboard keys using PC Doctor for DOS.  The program can be downloaded directly from here:
    http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-495KW2
    This program will create a bootable floppy with the diagnostic program.  If you prefer to use a CD-R, then I host the same file as an .ISO here:
    http://www.kawakami-ca.com/ibm_600x/dgpcdoc.iso
    Boot the system with the media and select the 600X from the menu of supported systems.  Once the diagnostic is loaded, select the Interactive Tests menu option (using the trackpoint or arrow keys and then pressing Enter) and then the Keyboard test, the Keyboard Keys and finally the 84 key(US/Hebrew) option.  That should display a crude map of the keyboard.  Pressing any one of the keys will cause the corresponding key on the display to go "reverse video".  My guess would be that you won't be able to get any reaction from the F1 key.  I was able to completely load the PC Doctor diagnostic and get to this test while keeping the F1 key down the whole time.
    The fix would be to try to pry off the keycap of the F1 key and see if there's anything you can do underneath.  I was able to get the keycap off by lifting the "back" side of the key toward myself.  There's a plastic/rubber dome which should be present.  If it's "deflated" then that is the cause of your problem. If it's missing, then there's probably some contamination on the board (i.e., a short) which makes the keyboard think you're pressing the key.  It might be possible to replace the dome but you have to glue it down without interfering with the switch contacts.  It's probably easier just to get a replacement keyboard.
    Ray Kawakami
    X22;X24;X31;X41;X41T;X60;X60s;X61s;X300;X301;Z60m;Z61t;Z61p;560Z;600E;600X;T21;T22;T23;T41;R50;A21p;A22p;A31 and A31p
    Not a Lenovo employee; just a volunteer helping out here
    All personal links to PC-Doctor software removed 8/2012 by mfg request

  • Where is the "setup" button on a canon printer MX 452

    Where is the "setup" button on a canon printer MX 452. Does anybody know? I'm supposed to push it to align the print head.

    What OS are you running?
    There is no hardware WPS button on the TC.. you can use it via the airport uitlity.
    The latest utility has added it.
    http://support.apple.com/kb/DL1628
    It is also possible also in 5.6 utility.
    Start the manual setup.. go to the top menu.. it is not in the main box. Add wireless clients.
    That brings up a hidden page in the AU
    Personally I have always done it manually via the printer wizard and simply setup wireless in the printer as infrastructure mode with the correct wireless name and password/security settings..
    WPS is a security risk.. apple only initialise it when you bring up this menu.

  • How to configure the Easy Setup to match the sequence type for playback

    Plesae provide some suggestion for how to configure the Easy Setup in FCP 6.05.
    *Uncompressed HD 8-bit (1920 x 1080p30)video streams
    e.g:
    1. Choose Final Cut Pro > Easy Setup.
    2. Choose ?? from the Format pop-up menu
    3. Choose “all rates” from the Rate pop-up menu.
    4. Click the USE pop-up menu, choose which format?
    Also how about Uncompressed SD 8-bit (720 x 480p30) video streams ?
    Thanks,

    Thanks for the advice.
    In the project, I created two sequences.
    Import all my HD 8-bit clips into sequence 1, and say yes to mach the format
    and import all my SD 8-bit clips into sequence 2 and say yes.
    In Sequence-> setting-> I verified the configuration as following:
    However, that is "Load sequence preset" button, I am not sure what is that for and also do I need to go to Final cut pro -> easy setup to configure the format again?
    I just want to playback all my HD clips to make sure no dropped frame and
    then playback my SD clips sequence to make sure the performace are OK.
    Here are the format for HD clips:
    HD 1920x1080 HDTV 1080i (16:9); upper; uncompress 4:2:2.
    Here are the format for HD clips:
    SD 720x480 NTSSC DV (3:2), NTSC-CCIR601, lower , uncmpress 8-bit 4:2:2.

  • How to kill custom Easy Setup / Sequence Presets?

    I set up some experimental Sequence Presets and Easy Setups and now want to delete them. I have tried every recommendation that I could find (details below) but they still show up in the lists. Where on earth are these things stored??
    Here's what I've done:
    1. Repaired disk permissions
    2. In FCP, selected the Sequence Preset and pressed the Delete button.
    3. Exited Final Cut Pro.
    4. Trashed the preferences by deleting these files:
    ~/Library/Preferences/com.apple.FinalCutPro.plist
    ~/Library/Preferences/Final Cut Pro User Data/Final Cut Pro 6.0 Prefs
    ~/Library/Preferences/Final Cut Pro User Data/Final Cut Pro Obj Cache
    ~/Library/Preferences/Final Cut Pro User Data/Final Cut Pro Prof Cache
    5. Emptied the Trash
    6. Rebooted the computer.
    7. Started Final Cut Pro.
    8. The Presets/Setups are still there!! Tried to find them by name with Spotlight. Doesn't find anything. Tried to find them using the command-line Defaults program. Doesn't find anything. Looked in
    /Applications/Final Cut Pro Additional Easy Setups
    They are not there.
    I also have Final Cut Express installed and trashed all its preferences too for good measure. But my custom settings will just not die.
    All ideas welcome!

    Agh auuuh agh? What a lot of coughing...
    1st thing to do: What format does your camera shoot? Make your Easy Setup & Sequence Settings reflect it.
    The wierd experimental formats are hiding. As a Final Cut Pro expert and official top user:

  • Which Easy setup to use?

    I just upgraded to FCP 5.1.2 and a new HDV video camera (Sony HDR-HC3) and have just reformatted and installed the Final Cut Studio suite and Shake. Now when entering the setup for FCP--what Easy Setup would be best? HDV 1080i (50,60, 24, 25)?
    Thanks.

    Please click on the or buttons over posts as appropriate...
    Patrick

  • E1200 and "Quick and Easy Setup"

    My parents were trying to setup their E1200 router. We had to do a reset (using the button) since we couldn't access the router admin menu (someone had hacked/changed the password). I'm doing this remotely over the phone.
    Now, when they open Internet Explorer, they are getting a"Linksys Quick and Easy Setup" screen no matter what web site they try to get to. They don't have access to the original CD to install Linksys Connect. Mom says that when she clicks on "No CD? Download the software" link, nothing happens. Looks like she's got internet, though, as there's a link to the Linksys forums, and she's seeing updates from the forums."
    I don't know what this screen looks like, but isn't there some way to get past this splash screen? The computer is plugged into the router via a cable, so I'm not sure why they can't access the internet manually. Is there a way to just "disable" the "Quick and Very So Not Easy Setup" and skip right to using the internet?
    Thanks.

    Hi dapupster. I suggest that you let your parents do another reset. Tell them to make sure that they press down the reset button that's underneath the device ( please check the  picture). Let them press it down for 30 seconds while the device is powered on.  Once done, let them unplug the unit, plug it back in and try to access the setup page manually through 192.168.1.1.
    If the challenge remains the same, let them unplug the router from the modem and have them access the 192.168.1.1 page with only the computer that's connected to the router.  Hope the suggestions help.

Maybe you are looking for