SecureCopy & 3000-series Concentrator...

I have a requirement to have an open-source configuration management solution log into my concentrator & download its config for backup / version control purposes. Its name is "RANCID".
I've enabled SSH, and I can log into the Private Interface with PuTTY just fine. When I use WinSCP 4.04, I have a problem. I authenticate just fine, but then the connection is dropped after 30 seconds. WinSCP tells me, "Incompatable shell, BASH prefered...". The concentrator tells me that the "PShell" is shutting down.
question: Is this just an incompatability with WinSCP specifically? Do you think others would work? I know the 3000-series is old, and end-of-life. I'm using the next-to-latest build of OS for the Concentrator.

Try to adjust SA lifetime and the max connect time in VPN concentrator.
Refer these links:
http://www.cisco.com/en/US/customer/products/hw/vpndevc/ps2284/products_tech_note09186a0080094eca.shtml
http://www.cisco.com/en/US/products/hw/vpndevc/ps2284/products_qanda_item09186a0080094cf4.shtml

Similar Messages

3000 series concentrator and L2TP over IPSec

All,
Anyone have any wisdom they are willing to share regarding the establishment of a L2TP over IPSec tunnel between Mac OS X and a 3000 series concentrator? I believe that the concentrator is accepted the IKE SA proposal, but I can't get any further and I'm not able to get any useful information out of the logs on either side of the tunnel. The client side simply reports that "L2TP cannot connect to the server", the concentrator reports "Connection terminated for peer". It has clearly exchanged some valid information because the concentrator has assigned the traffic to the correct group (a non-default group I've set up specially to test this connection).
Looking at the packet dump I can see the two devices exchange some information, then the client starts sending ISAKMP packets (quick mode) that the concentrator seems to ignore.
Thoughts, suggestions, anecdotes etc. are all welcome.

Try to adjust SA lifetime and the max connect time in VPN concentrator.
Refer these links:
http://www.cisco.com/en/US/customer/products/hw/vpndevc/ps2284/products_tech_note09186a0080094eca.shtml
http://www.cisco.com/en/US/products/hw/vpndevc/ps2284/products_qanda_item09186a0080094cf4.shtml

Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

Hi All,
Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
Any help would be greatly appreciated.
Thanks in advance.
Samir

Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices. RME will only use HTTPS to fetch VPN concentrator configurations.

Dell Inspiron 11 3000 series

I have an acer aspire one that has been trucking along for nearly 6 years now with almost continuous use (about a year of non-use time in there, but that's it). I use it primarily for taking notes in class and such, but it also sees a lot of programming and other use since I take it to campus each day and also on trips. In this time, I have lost almost all the feet and now screws are slowly disappearing. It also has started to have some overheating issues when the heatsink seems to shift positions slightly (it shuts off within 90 seconds when this happens). In addition, I find myself wishing quite often that it could do things like stream video properly (without jittering) and compile the kernel (it takes FOREVER on that tiny hyper threaded single core atom processor). So, I've been looking at a replacement that can get similar battery life, has a similarly sized screen (preferably touch as well because I think that would be great fun to use), more than 1Gb of RAM (I can have about 7 tabs open on chrome and then it starts having troubles since I have swap disabled), and a better processor. My most basic requirement, however, is that the laptop be able to run arch.
I've been looking at the Dell Inspiron 11 3000 series since it seems to have the best battery life of my various 11.6" options out there. The processor is a dual core Celeron which sounds old and antiquated to me, even though I believe its based on Haswell (not sure there). It also has 4Gb RAM and 500Gb hard drive. Another option, for $50 more, is a pentium processor which sounds even more antiquated, but is still based on Haswell.
http://www.dell.com/us/p/inspiron-11-31 … redir=true
My question is this: Has anyone managed to get arch working on one of these things? I also imagine that the most new-fangled component would be the touchscreen, so does anyone know the general support of those for linux?
Thanks in advance for any help.

Hi,
Does the WPF application develop by yourself? Please make sure that your application has no dependency issue, if your WPF application lacks of some libs or .Net framework, it cannot execute. Do you get any error message when you try to run it?
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Flickering problem on screen - 3000 series N200 laptop

Hello!
I have a 3000 series N200 laptop (0769 type) for 3 years. Approximately 3 months ago, there was a screen problem that the screen had white vertical gridlines. Service replaced the chipset of the graphical card.
Yesterday, a flickering problem has been appeared. I updated bios and display drivers from below link.
http://support.lenovo.com/en_US/downloads/default.page?
Could not get a solve with those updates. Then, I dismounted the front cover of screen. Re-assembled the LVDS FFC cable of the LCD display a couple of times, problem continued. Then, re-assembled the inverter cables. It also did not provide a solution.
>See the problem photo (1.jpg) at below link.
https://docs.google.com/open?id=0BweTh37k3ZRSQWYxRFNIWWpGSFE
Please advise about this matter.
Thanks.

Hello suguz and welcome to community,
As you have already updated the video driver and BIOS then you can check with adjusting the monitor refresh rate to 60Hrz.
Kindly check the same issue in BIOS mode and if issue continues then it might fault with Lcd display.
Best Regards,
Tanuj
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Battery Maximizer Lenovo 3000 Series

I would like why no Battery Maximizer software for 3000 Series systems/notebooks?
Why only for ThinkPad series?

I tried but it says "cannot install on this system"
whats more interesting? the lenovo training website says you need to use the battery maximizer software to get maximum battery time.
So I ask where is battery maximizer software for N100 3000?

DC jacks; are they compatible with all 3000 series

I would like to know if all the DC power jacks are the same or compatible for all the lenovo 3000 series notebooks?
I have a lenovo 3000 C100 notebook, and the problem that I am experiencing is that the unit dose not power up when
the power button is press. here's the rundown of the problem; when I plug the power cord onto the laptop the indicator
ligth for the power is on, but when I press the power button to on, the power indicator turns off and the laptop does not
turn on at all, the only time the power indicator turns on is when I disconnect the power cord from the laptop and plug it
back on. I also try it with the battery without the AC cord, the indictor lights for both power and battery is on, but when the
the power button is pressed both indicator lights will flash (one at a time ) for at least 2 seconds and does not come back
on at all and the laptop still does not power up at all. I have also tested the unit with another different battery and AC power
cord from a same working 3000 C100, still the same issues. so I figure that it has to be the power DC jack, check lenovo
website, but found none for the C100. so I want to know if other DC jack from let's say the T4 or T60, Thinkpad can be use
as replacement part for my unit. my laptop is only a year and a half old. I would be very gratefull for any kind of help.
Thanks

there are not many motherboard for Lenovo 3000 laptops on sale on the web, the only place where you can get it, is through Lenovo parts service... i would suggest you sell your laptop for parts and then get a new laptop, it would be probably be more economical that way then getting a new motherboard through Lenovo.
Message Edited by wjli2 on 10-15-2008 09:04 PM

Vms 2.1 can't link up with the vpn 3030 series concentrator

Hi Netpro,
Currently I had installed the vms 2.1 server, but I have no clue how make the vms 2.1 to communicate with the vpn 3030 series concentrator.
Can anyone give me the guideline?
Thanks in advanced.
Regards,
stephen yap

You could refer to the quick start guide at http://www.cisco.com/en/US/products/sw/cscowork/ps2330/ps5211/index.html

Tds 3000 series - downgrade driver

hello, i need another driver conversion to labview 8.2 to 7.1
this time for tektronics tds .3000 series
Using LabVIEW 7.1
Attachments:
tektronix_tds_3000_series.zip ‏1008 KB

no need anymore
Using LabVIEW 7.1

IAS and Cisco Concentrator 3000 series?

Is anyone authenticating their VPN users via Windows IAS, if so how. I would like them to be only to get on the network if they are in a particular Active Directory group (not local IAS users)
Thanks

Hi,
Yes , it works fine. For network access you need to set up group policy.
Regards,
~JG

Cisco 4000 & 3000 series ip route & ip default gateway

Dear all ;
I have Enterprise Network Contain :
- Foundry Big Iron work on layer 3 , and Combination of 4000 and 3000 and 2000 cisco switches work on layer 2;
management network for the switches is 192.168.100.0
Foundry Big Iron is 192.168.100.1
i use ip default-gateway 192.168.100.1 on all cisco switches.
all other subnets route through the foundry.
but when i ping from any subnet (192.168.15.0) to any 3000 or 2000 switches series it replay and when i ping to 4000 series it don't replay.
when i use default route command on 4000 series it replay.
i need some explanation
Kind Regards

In the original post it describes the Cisco switches as operating as layer 2 switches and I assume that in terms of how they are configured to forward traffic all the Cisco switches including the 4000 are configured only for layer 2 forwarding. But with IP routing enabled (as seems to have been the case on the 4000) the behavior of the switch becomes a bit different. In particular is the difference in how you identify the default route. For a switch that is layer 2 only you use the default-gateway command (which apparently worked fine for the 2000 and 3000 switches). But when you enable IP routing then the switch does not use the default-gateway to learn its default route and would look for some other mechanism to learn its default route. I am assuming that there was not any other mechanism and so the 4000 basically did not have a default route. When you configure no ip routing (which was good advice from Paul) then the 4000 stops working as layer 2 switch and at that point will use default-gateway to determine its default route.
HTH
Rick

CE Utility Diskette for Lenovo 3000 series ???

Hello
I'm searching for this Lenovo Tool ...
Which was described in the Lenovo 3000 Hardware Maintenance Manual
Can everybody help me ??
Thanx
Frankmen

frankmen, welcome to the forum,
I wasn't aware that any Business Partners in Germany are allowed to provide warranty service on 3000 or IdeaPad systems, please correct me if I'm wrong on this; it would be interesting to know.
Being a business partner you will be able to contact your Lenovo representative who will certainly be able to put you in touch with the person(s) to speak to about this.
Also, if anyone were to post a link to the utility from these forums it would be immediately removed by moderators.
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

3000 series and Multiple DHCP scopes (DHCP-relay)

I need to send different DHCP options to users; however, I need to put certain groups in different subnets. Is it possible to setup the concentrator to relay for addresses from different scopes?

- Configuration
- System
- IP Routing
- DHCP Relay
a. Enable 'Enabled' checkbox
b. Select Forward to
c. Address == 192.168.10.8 255.255.255.0
- Address Management
- Assignment
a. Enable 'Use DHCP'
- User Management
- Groups
- Select 'groupA'
- Modify Group
- Click General tab
- Enter 'DHCP Network Scope' x.x.x.x
- Select 'groupA'
- Remove Address Pool
Now I get the following error:
118 02/08/2005 13:29:00.720 SEV=3 DHCPDBG/39 RPT=34
DHCP discover timeout: no response from polled servers (xid 3821297335)
I can ping the server, and it is serving up this scope to other devices (just not from the concentrator)

Dell Inspiron 15 3000 Series, Problem installing Network driver, Wireless Key not working

Hi,
This is a brand new Dell, which has Windows 8.1 Pro 64bit installed, and I re-installed all drivers, and did BIOS update as well, but when downloading Network drivers with correct Service Tag and product, I get to the installation screen where it asks to Activate Wireless Key. The Fn + PrtScr does not work, even if I go to PC Settings, Bluetooth, I can switch it on with mouse, but when using the Fn + PrtScr it does not switch between On & Off within PC Settings. So I cannot install the Wireless drivers at all, I have to Cancel Installation.
Any suggestions?

The Service Tag may be listing the wrong wireless card variant. Please provide the hardware IDs so we can confirm:
http://dellwindowsreinstallationguide.com/downloading-drivers-checking-hardware-ids-and-downloading-and-installing-dell-system-drivers-in-the-correct-order/checking-hardware-ids-in-the-device-manager/

Looking for Best Hardware solution for PSTN to PBX spa 3000 series, a plug in pc card or ?

Hi All,
I'm looking at the SPA3120 voip router as a possible device to connect a single analog phone line to a linux based PBX- perhaps asterisk or freeswitch.
Any voice mail and call routing (inter office or office to/from pstn) should be handled via the pbx.
VOIP is another matter, office phones (4) are planned to be ip based and will connect via common ethernet line.
Right now just need a low cost analog to pbx device. is the spa3120 the device to use or should I look at perhaps a x100p pci card installed in the server? with the spa device I don't have as much to worry about regarding pbx & linux hardware issues.
New to all this so feeling a bit lost...

Hi.
These products are being handled by the Cisco Small Business Support Community.
*If my post answers your question, please mark it as "Accepted Solution".
Thanks!

SecureCopy & 3000-series Concentrator...

Similar Messages

Maybe you are looking for