Security License for Cisco 3900 Series

Hi,
I am having Security License (SL-39-SEC-K9) for Cisco 3900 Series router, Can somebody help me to provide sample config to configure 3945 router to act as firewall. Is there any difference with the native IOS based firewall config..
Regards,
Mukesh

Here is a detailed instruction on ISR G2 licensing (including downloading, installing, rehosting license, etc.).
Usually, you just need to go to cisco.com/go/license, enter PAK and follow detailed instructions.
HTH
Alexandr

Similar Messages

Security License for Cisco 3925

Hi,
I have got cisco 3925 without security license. Now I have got the L-SL-39-SEC-K9 license and need to install it. What is the process of installing this license.
Thanks in advance
Regards,
Mero

Here is a detailed instruction on ISR G2 licensing (including downloading, installing, rehosting license, etc.).
Usually, you just need to go to cisco.com/go/license, enter PAK and follow detailed instructions.
HTH
Alexandr

License on the Cisco 3900 Series router.

I am trying to understand what does the "data" license exactly do on the Cisco 3900 series router. What I understood is that the data license supports "MPLS.ATM. Multiprotocol support".
Question is is a do not have this license will I not be able to run BGP, EIGRP and terminate service provider links?
Technology Package License Information for Module:'c3900e'
Technology    Technology-package                  Technology-package
              Current              Type           Next reboot
ipbase        ipbasek9             Permanent      ipbasek9
security      securityk9           Permanent      securityk9
uc            None                 None           None
data          None                 None           None
NtwkEss       None                 None           None
CollabPro     None                 None           None
Configuration register is 0x2102
Thanks,
Nik

I think WAAS express is one of the technologies you will lose out on. Amongst other advanced features. See link below.
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/software-activation-on-integrated-services-routers-isr/white_paper_c11_556985.html
EDIT: And performance routing.

NetConfig issue wrt Cisco 3900 Series Router

Hi Cisco;
I can't able to configure my Cisco 3900 series Router via NetConfig tool. While I am able to Configure all other Routers (7600, & 2800) and Switchs (6500, 3700, 3560). I can accessable 3900 Series Router via Inventory Collection, Sync Archieve, Campus Manager, DFM and etc.
I have Cisco LMS 3.2 with RME 4.3 & using SNMPV3.
Thanks for your support.
Best regards;
Shoaib Ahmed

Hi Clarke;
Please find the requested Screen Shot.
Actully my problem is that, I can't configure my Cisco 3945 Routers (Shows not applicable devices) via NetConfig tool. I can use other tools like Sync archieve and etc is working fine for these 3945 routers.
Best regards;
Shoaib Ahmed

IOs for cisco 1900 series router

Hi,
Kindly provide me the IOS version (cisco 1900 router) which can fix the below listed Bugs,
Cisco IOS TCP Listener Crafted Packets Remote DoS (CSCek37177)
Cisco Multiple Devices Crafted IP Option Remote Code Execution (CSCeh52410)
Cisco IOS System Timers Remote Overflow (CSCei61732)
Cisco IOS Secure Shell Server TACACS+ Multiple DoS (CSCed65778, CSCed65285)
Cisco IOS IKE XAUTH ISAKMP IPSec SA Establish Authentication Bypass(CSCeg00277)
Cisco IOS Telnet Service DoS (CSCef46191)
Cisco IOS H.323 Protocol Implementation Flaws Cisco IOS Malformed IPv4 Packet Remote DoS Cisco SSH2 Server/Client Malformed Packet Remote DoS (CSCdz60229, CSCdy87221, CSCdu75477)
Cisco IOS SSH Large Packet CPU Consumption DoS (CSCdw33027) Cisco SIP Crafted INVITE Message Handling DoS (CSCdz39284, CSCdz41124) Cisco IOS Data-link Switching (DLSw) Capabilities Exchange Remote DoS (CSCsf28840)
Cisco IOS AAA RADIUS Long Username Authentication Bypass (CSCee45312)
Cisco IOS TCLSH AAA Command Authorization Bypass (CSCeh73049)
Cisco IOS MMP Stack Group Bidding Protocol (SGBP) Crafted UDP Packet Remote DoS (CSCsb11124)
Cisco IOS IPv6 Packet Processing Arbitrary Code Execution (CSCef68324)
Cisco IOS Malformed BGP Packet Processing Remote DoS (CSCee67450)
Cisco IOS Multi Protocol Label Switching (MPLS) Packet Remote DoS (CSCeb56909)
Cisco IOS IPv6 Packet Processing Remote DoS (CSCed40933)
Cisco IOS SCCP Control Protocol Malformed Message DoS (CSCee08584)
Cisco IOS OSPF Packet Handling DoS (CSCec16481) Cisco IOS ARP Table Overwrite DoS (CSCdu81936)
Regards,
Bala

Hi,
The Current running IOS version is 12.2(4)T7. I tried through bug toolkit. but i couldn't able to consolidate the IOS to fix these bugs.
Regards,
A.Bala
leolaohoo wrote at Tue Jan 25 02:20:52 GMT+05:30 2011:
>Balakrishnan Appavu,
>
>A new message was posted in the Discussion thread "IOs for cisco 1900 series router":
>
>https://supportforums.cisco.com/message/3277195#3277195
>
>Author : leolaohoo
>Profile : https://supportforums.cisco.com/people/leolaohoo
>
>Message:

Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

Hi All,
Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
Any help would be greatly appreciated.
Thanks in advance.
Samir

Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices. RME will only use HTTPS to fetch VPN concentrator configurations.

User License for Cisco CUCM 7.1.3

Hi
I need 30 unit license for Cisco Communication Manager 7.1. But I found that it's already end of sale.
I want the unit license part number for cisco cucm 7.1.3 version.
And i found revised part numbers for user license (CUCM-USR-LIC ) but those for 8,x versions. If i purchase that will it support in CUCM 7.1.3?
Thanks in advance.

Hi,
CUCM 7 is already end of sale.
CUCM 7.1.5 supports UCL.If we refer the ordering guide of CUCM 8.5, you can get UCL licenses [Basic/essential].
http://www.cisco.com/web/partners/downloads/partner/WWChannels/technology/ipc/downloads/UC_8_6_OG.pdf
What I think if u place the order , you should get the licenses and at the backened, it would be DLU.
You can also speak to Cisco SE for further clarity.
regds,
aman

Contact Center Enhanced License for Cisco 2951 Router

Hi,
I need an urgent help to get the exact part number/details of Contact center enhanced license.
I couldn't find in CCW or any other tool about this license with Cisco 2951 Router (CISCO2951-V/K9).
To run this license on mentioned router, do we need to order it separately or we can take it with router?
Please respond asap.

Hi Andre,
I was just refering the Ordering guide which says
Updating UCSS contract when upgrading Unified CCX licenses
UCSS cannot be upgraded from one category to another (e.g. Standard to Enhanced). If
the customer upgrades within the solution, they need to purchase UCSS for greater or
equal value to cover the new version, then they can request a credit on the unused term
of the original purchase from Customer Service
you can also speak to [email protected] for more details on ESW.
regds,
aman

Need MIBs for Cisco 2500 Series WLC

Hi,
I need the MIBs for Cisco 2500 WLC.
I have it for 5508 WLC. Does it works same for 2500 WLC too ?
Regards

they should be very similar. There would be more trees available for the 5508 over the 2504.
You can get the MIBS for the 2504 from the Software downloads section of CCO.
Steve

ASA license for Cisco IP Phone over VPN

Hi,
Are there special licenses required on the ASA to use Cisco IP Phones (Hard phone) over SSL VPN connection?
Thanks

Hi,
You can purchase the phone proxy license. This elimiates the need to build a VPN tunnel for voice traffic.
It is not mandatory to purchase this license however.
From the ASA configuration guide:
http://www.cisco.com/en/US/docs/security/asa/asa83/configuration/guide/unified_comm_phoneproxy.html#wp1144845
"The Cisco Phone Proxy on the adaptive security appliance bridges IP telephony between the corporate IP telephony network and the Internet in a secure manner by forcing data from remote phones on an untrusted network to be encrypted. "
Don't forget to rate all posts that are helpful.

Licensing for Cisco ESA c380

I am putting a recommendation together for a client to upgrade their existing Cisco ESAs and trying to figure out how the licensing works.
We are looking at c380s across multiple sites, upgrade from their current models which are c160s. Questions:
1.) Do the mailbox licenses need to be procured separately for each c380. For e.g., if the total mailbox no. is 20000 across 4 sites, can the mailbox licenses be bought together and 'split' on individual installs of c380s OR they have to be bought separately for each c380.
2.) If upgrading from the existing ESAs to new, can the licenses be imported from the existing c160s (which will be decommissioned) and exported to the new ESAs?

1) each hardware appliance is licensed separately. You'll need to work with account team/reseller to provide the #/size license as appropriate.
2) If upgrading - yes, you'll just need to transfer the existing "as-is" license from the serial number of the existing appliance to the serial number of the newly purchased appliance. Should be fairly exact to the RMA steps provided in the following article:
http://www.cisco.com/c/en/us/support/docs/security/email-security-appliance/118000-technote-esa-00.html
I hope this helps!
-Robert
(*If you have received the answer to your original question, and found this helpful/correct - please mark the question as answered, and be sure to leave a rating to reflect!)

Content Security Licensing on Cisco ASA

Hi Guys,
Need help on licensing of content security on Cisco ASAs. Hope someone would be able to help.
Our customer has a ASA5520-CSC20-K9 (default 500 users) appliance. When the appliance was first bought, they upgraded it to 750 user license and PLUS feature license. They want to renew these licenses. Kindly advise the following:
1. In order to do so, is it right that the customer has to purchase both the following (to cater to the 750 users and PLUS features)?
• L-ASACSC20-500UP1Y ASA 5500 CSC-SSM-20 500-User w/ Plus Lic. Renewal (1-year)
• L-ASACSC20-250UP1Y ASA 5500 CSC-SSM-20 250-User w/ Plus Lic. Renewal (1-year)
2. Do the renewal licenses above include BASE features (Anti-Virus, Anti-Spyware, File-Blocking)?
Thanks!
Citra

That unfortunate. It seems like with the VPN licensing they realized if you were in an active/standby configuration then you should only have to pay for one license, thus the license change in 8.3+ only requires you to purchase one license. I thought this would have carried over into IPS.
Beings we haven't failed over to the standby unit in 2 years, would it be possible to install the IPS module in both the active and standby appliances, but just license the one in the active mode? I don't care if we are running without IPS on the standby if we did have to failover for some amount of time. Or does having it licensed on one and not the other mess with being in active/standby failover mode?

Scripting reboot for Cisco 300 Series switches

I would like to have some help putting together a script for rebooting our 300 series POE switches. I have about 150 at this stage to administer and it would make it much easier not to have to remotely reboot them. The IP settings will be the same for each location and we have about 2-5 in each location. I will be logging in through logmein to each remote server, and will run the scripts from this to the local switches. Any help would be appreciated.

I was playing with my Indigo on an SG-500 and it seems to work. Create a session for each switch and in the session properties for each switch enter your crendentials (user/pass) IP/port, etc, I was using telnet, port 23 for this and then under the send command tab, on connection I entered:
reload
y
One command per line up to 20 commands I believe and it connected, I saw my prompts and replies and then shutting down.
So if you try this you can just go down the file tree list for switches with cameras than need a reboot and restart the entire switch if you like, quick and easy.
You could also add a folder for each switch and a session in that folder possibly for each camera/port with online port number changing for each camera in the session properties and then selectively cycle power for just the affected cameras.
Example for port 22/camera xxxx:
conf t
int gi22
power inline never
power inline auto
It would take a fair amount of time to set up but once done you could just pick a switch folder and the port in that switch to cycle. If you have multiple port on a switch you could use
conf t
int range gi22-24
or
int range gi1,6,16,20
power inline never
power inline auto
might have to verify that syntax

Licensing for Cisco Network Topology Icons

A large collection of Cisco network topology icons is available for download at http://www.cisco.com/web/about/ac50/ac47/2.html. These icons are pretty much the standard for network topology diagrams.
I would like to know if Cisco allows the use of these network topology icons in training materials developed and sold by individuals/companies other than Cisco.

Try this
http://www.cisco.com/en/US/solutions/ns340/ns414/ns742/ns982/cvd.html link.
Thanks
Kunal

There is a trial license for Cisco CSP COLLECTOR ?

(SNTC-CSPC2.3.1.1-RC4-Build_OVF10_1)
PSS

Moving this discussion to the Creative Cloud forum.
MarilynDiPasquale if you are attempting to enter a redemption code then I would recommend reviewing Redemption Code Help. The page provides guidance on how you can redeem your code for a membership.

Security License for Cisco 3900 Series

Similar Messages

Maybe you are looking for