Security processor was unable to find a security header in the message. This might be because the message is an unsecured fault or because there is a binding mismatch between the communicating parties.

We have a web role where we have hosted a WCF service.
We are facing the below exception intermittently on consuming the service.
Security processor was unable to find a security header in the message. This might be because the message is an unsecured fault or because there is a binding mismatch between the communicating parties. This
can occur if the service is configured for security and the client is not using security.
This is intermittent. Few calls fail , and the subsequent calls succeed without making any changes.
Please help in overcoming this abnormal behavior.
Thanks in advance !!
Best Regards ,
Eswar

Hi Eswar,
As the error message mentioned, it may be a mismatch between the configuration on the client and the server.Try putting all your configuration in a binding configuration and then use the same binding configuration on the server and client. Since this issue
is more related with WCF, I suggest you move to WCF forum, it is appropriate and more experts will assist you.
Best Regards,
Jambor
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Similar Messages

Airport Utility was unable to find your Airport device after restarting.

- I just updated the firmware on my base station (it a white dome?? i think snow?) to 5.7
- I am running AirPort Utility 5.5.2 (also recently updated)
- I have (3) AirPort Expresses (just updated firmware yesterday) and now are not being seen in the airport utility. They had been running for about two years just fine.
I have done a hard reset and was then able to see the Airport Express and go through set up. Upon finalizing the set up I get this message:
"Airport Utility was unable to find your Airport device after restarting."
This is happening with all 3 AirPort Expresses

Hello !
I had the same kind of problems when I upgraded to the latest version of Airport (5,7).
The Airport express seemed to have been disconnected, and nothing I could do to reconfigure it, after hard resetting it, seemed to be working.
I did two or three hard resets before remembering having been in a situation like that a while ago.
I went back to the Mini, **deactivated the firewall (in the "preferences" panel), then deactivated also the firewall of the Modem/router provided for my internet connection. Then I went in the other room and did another hard reset of the Airport express, came back in the mini's room, opened the Airport utility, the icon of the Airport express was already visible (which wasn't the case before... ), did the re-configuring.
The reconfigured Airport express reappeared very quickly, then I reactivated the firewalls of the Mini and the router. Voilà !
It took less than two minutes !
And since then the Mini have been streaming music without a glitch to the Airport express.
I hope this will help you and others !

Digital Signature- SSF error: Unable to find external security product

Dear Friends,
After I enter my User ID and Password, this displays this error !!!
SSF error: Unable to find external security product
Would really appreciate your help.
Thanks,
Sri

Hi Sri,
Would you pls check the installation of the security toolkit on your application server?
Which security product do you use?
The standard security product is SAPSECULIB (library sapsecu.dll).
Please check the SSF initialization messages which are contained in each dev_w## developer trace (transaction ST11). When successful, the initializaion messages look like this:
N =================================================
N === SSF INITIALIZATION:
N ===...SSF Security Toolkit name SAPSECULIB .
N ===...SSF trace level is 0 .
N ===...SSF library is /usr/sap/<SID>/SYS/exe/run/sapsecu.dll .
N ===...SSF hash algorithm is SHA1 .
N ===...SSF symmetric encryption algorithm is DES-CBC .
N ===...sucessfully completed.
N =================================================
General information for SAPSECULIB can be found in SAP note 354819.
Best regards,
Christoph
P.S.: Please reward points for useful information.

HT5312 i was unable to reset my security questions, and i do not have a rescue email   Please i need to reset them to be able to use my apple id again normally

i was unable to reset my security questions, and i do not have a rescue email   Please i need to reset them to be able to use my apple id again normally

halaalsalhi wrote:
i was unable to reset my security questions, and i do not have a rescue email
See Here > Apple ID: Contacting Apple for help with Apple ID account security
          Ask to speak with the Account Security Team...
Or Email Here > Apple Support iTunes Store Contact

The token provider was unable to provide a security token

I am configuring workflow for SharePoint 2013. For that I am creating a workflow farm and selected custom settings and selecting certificates from personal store. When I am select the option where it will auto generate the certificate configuration
successful.
while selecting the certs from personal store, configuration failed to add host to workflow farm and throwing below error
Configuring Workflow Manager runtime settings.
The token provider was unable to provide a security token while accessing 'https://hostname:9355/WorkflowDefaultNamespace/$STS/Windows/'. Token provider returned message: 'The underlying connection was closed: Could not establish trust relationship for the
SSL/TLS secure channel.'.
Thanks,
Neetu
neetu

Hi,
When I am trying to receive the same messages from a Azure service bus subscription using .net (C#) client,
BusSubscriberbusSubscriber =
newBusSubscriber("TestTopic2",
"Endpoint=sb://overcasb.servicebus.windows.net/;SharedSecretIssuer=owner;SharedSecretValue=wqYlT4yHZimeUZacH+1V1hj/ZrKu7zK9ELaaLYDxqjc=",
"AssetMovement",
"AssetMovement");
I am getting the same error here also.
"The token provider was unable to provide a security token while accessing 'https://overcasb-sb.accesscontrol.windows.net/WRAPv0.9/'.
Error Code: 407 Proxy Authentication Required. The ISA Server requires authorization to fulfill the request. Access to the Web Proxy filter is denied. (12209)
By setting <defaultProxy useDefaultCredentials="true" /> in appconfig, I got rid of the above error. And now its working fine with .net(C#) client.
<configuration>
<system.net>
<defaultProxy useDefaultCredentials="true" />
</system.net>
</configuration>
The same setting I tried in BTSNTSvc.exe config file and ofcourse restarted the host instance but still getting the same error. Any help?
gautam

HT3728 Base station error, air port utility was unable to find my airport device. Why does it say this when it recognizes my airport on the computer? Yellow light has been on

Base station error, air port utility was unable to find my airport device. Why does it say this when it recognizes my airport on the computer? Yellow light has been on

On the older version of the AE you can still use older airport utility.
But once you load the new one you cannot easily go back.. you can load an older 5.6 version though.. instructions below.
For 6.3 you need to run ipv6 local link.
see http://support.apple.com/kb/TS4597
How to load 5.6 into ML.
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
Leave the package open on the desktop so you can see the file. AirportUtility56.pkg
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. If your Mac refuses to run the software, because it wasn’t downloaded from the Apple store, go to security in preferences and allow other software to work.. this is limitation of trade methinks. You can set back later if you like.
Now drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. in finder, open the new directory, drill down.. applications, utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall version 6 (now 6.3 if you updated) so don't try.. and you cannot or should not run them both at the same time.. although I have had no problems when doing so.

Office Web Apps - Office Web Apps was unable to find the specified certificate

Hello,
Let me start by saying I did not see a forum listed for Office Web Apps and figured the SharePoint forum would be the second best place to post this. With that said, here's my issue...
I installed OWA 2013 on a Windows Server 2012 (not R2) VM and installed all the prereqs as described here: http://technet.microsoft.com/en-us/library/jj219455(v=office.15).aspx Since this is a test environment, I'm planning on using a self-signed
cert which appears to be supported based on info found here: http://technet.microsoft.com/en-us/library/2e147f11-6f47-46bc-90bf-b2f179958d11(v=office.15)#certificate.
I created the cert using the following command:
New-SelfSignedCertificate -DnsName owa.test.local -CertStoreLocation cert:\LocalMachine\My
I then edited the cert's properties in the Cert Manager MMC snap-in and added a friendly name of "2014_OWA_Cert". I then proceeded to try and create the OWA farm by running:
New-OfficeWebAppsFarm -InternalUrl "https://owa.test.local" -CertificateName "2014_OWA_Cert" -EditingEnabled
This produces the following error:
New-OfficeWebAppsFarm : Office Web Apps was unable to find the specified certificate.
At line:1 char:1
+ New-OfficeWebAppsFarm -InternalUrl "https://owa.test.local" -CertificateNa ...
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : ObjectNotFound: (:) [New-OfficeWebAppsFarm], ArgumentException
+ FullyQualifiedErrorId : CertificateNotFound,Microsoft.Office.Web.Apps.Administration.NewFarmCommand
What gives?

Hi Waqas
Thanks for your help with this. I had a look at both posts, the URL works fine from the WAC server and I am not using a System account to test docs.
Also, this is a production site that is accessible over the Internet, so we are using https therefore the WOPIZone is external-https.
Issue #3 in the above blog link does not reflect the same error I see on my servers.
I also had a look at the information in this link: http://technet.microsoft.com/en-us/library/ff431687.aspx#oauth
Problem: You receive a "Sorry, there was a problem and we can't open this document" error when you try to view an Office document in Office Web Apps.
If you added domains to the Allow List by using the
New-OfficeWebAppsHost cmdlet, make sure you’re accessing Office Web Apps from a host domain that’s in the Allow List. To view the host domains in the Allow List, on the Office Web Apps Server open the Windows PowerShell prompt as an administrator and run
the Get-OfficeWebAppsHost cmdlet. To add a domain to the Allow List, use the
New-OfficeWebAppsHost cmdlet.
I have not added any domains to the Allow list so this did not help either. Should I add the domain?
Any further help with this is much appreciated.
Thanks again.
Yoshi

Alert subscription data source module encountered errors while running: Alert subscription data source module was unable to find alerts that match the subscription because of database errors.

Hi, We recently started getting these errors a couple times a day. There are 12 of them in total. We also have exactly 12 subscriptions. Does this indicate some db issue causing all of these
to fail?
Alert subscription data source module encountered errors while running: Alert subscription data source module was unable to find alerts that match the subscription because of database errors.
The following error(s) were encountered:
Exception Message: ExecuteScalar requires an open and available Connection. The connection's current state is closed.
One or more workflows were affected by this.
Workflow name: Subscription8b108a3e_4e3d_4fd0_b67e_cbfc21cd10b8
Instance name: Alert Notification Subscription Server
Instance ID: {E07E3FAB-53BC-BC14-1634-5A6E949F9230}
Management group: A Company Management Group
Thanks Lance

Hi,
Do you have hotfixes applied?
http://blogs.technet.com/kevinholman/archive/2009/01/27/which-hotfixes-should-i-apply.aspx
Also, I found a relevant thread for your reference.
Alert subscription data source module encountered errors while running</u1:p>
http://social.technet.microsoft.com/Forums/systemcenter/en-US/50557249-7f97-4b67-9729-f7088202385b/alert-subscription-data-source-module-encountered-errors-while-running?forum=operationsmanagergeneral</u1:p>
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Airport Utility 5.4.2 was unable to find Airport Extreme base station.

I downloaded the new Airport Utility 5.4.2 to my 2009 24" iMac with Snow Leopard. Now it is unable to find my Airport Extreme base station or Airport Express. My iMac is connected to the network via the Airport Extreme base station but the Airport Utility cannot find it. All I get is this message "Airport Utility was unable to find any Apply wireless devices. Make sure the Apple wireless device you want to set up is plugged in and in range of your computer and then click rescan to try again". I clicked rescan numerous time with no luck. I even downloaded the Airport Utility 5.4.2 again with no luck. What is wrong??? Everything was working fine until I downloaded the Airport Utility 5.4.2.

Thanks for the info.
Following your same steps exactly, I am able to save the configuration file to the desktop, or navigate to another folder to save it at that location.
I was able to do this previously with 10.5.x and with current Snow Leopard. Notice that you list 10.4.x as your operating system. If you are still running this OS, it could be that 10.4.x does not allow this feature with 5.4.2?
Not sure if downloading another copy of 5.4.2 would be worth the pain, as I'm inclined to believe that it probably would not help solve your issue. If you decide to do this, please post back with your results.

Why do I get a error saying mail was unable to find your reply. You may have deleted message.

when sending email, I sometimes get an error stating: Mail was unable to find your reply to: You may have deleted message. This does not happen with every sent message but it is doing it more and more. The reply is no where to be found.

You posted in a 4 month old dead post.
You would do better by posting a "New Topic" in the OS/Mail forum area of which os you are using. You will need to indicate which version os you are using as well as which version of Mail you are using in order to get the proper attention to your post. This will help the users reading your post to suggest solutions.

Hi when i open Photoshop i get this message in a little box (could not complete the command because Photoshop was unable to find the JavaScript plug-in.) Im using the trial version of Photoshop

im wondering if anyone can help with this
I get this message when i open PhotoShop
(could not complete the command because Photoshop was unable to find the JavaScript)

Photoshop installer should have installed a ScriptingSupport Plugin in each version of Photoshop you installed. Scan your system for ScriptingSupport I found six on my windows system. Here where I found them:

Trying to set up time capsule but keep getting message stating airport utility was unable to find any airport wireless device. What do I do know?

Trying to set up my time capsule on my imac.
Keep getting message "Airport utility was unable to find any airport wireless devices."
What do I do now?
joglenn

When having difficulties accessing the Time Capsule (TC) via the AirPort Utility, try the following, in order checking accessibility with the utility after each step:
Check the local connection. If you are trying to access the TC wirelessly, make sure that you are connected to its wireless network before running the AirPort Utility to administer it. If you are still unable to access it with the utility, temporarily connect your computer directly using an Ethernet cable to one of the TC's LAN ports.
Power cycle the base station. Remove the power adapter's plug from the power outlet, and then, wait 15 seconds before plugging it back in.
Perform a "factory default" reset on the base station.
Finally, if you are attempting to access the TC via an Ethernet connection, be sure that your Ethernet port is NOT configured for Jumbo Frames, i.e., using an MTU of 9000+.

Alert subscription data source module was unable to find alerts that match the subscription because of database errors.

We have been seeing this error in the Operations Manager Event Log for quite a while.
Alert subscription data source module was unable to find alerts that match the subscription because of database errors.
The following error(s) were encountered:
Exception Message: ExecuteScalar requires an open and available Connection. The connection's current state is closed.
One or more workflows were affected by this.
Workflow name: MMEA_1348391424
Instance name: aaa.bbb.com
Instance ID: {88AED57C-5627-0C0B-E5C1-A9176A7E64CD}
Management group: SCOMr2
I haven't been able to spot any network outage on the management servers, or the database servers to indicate a problem. It usually happens at night, and when I look at the health explorer, the entity is healthy.
Please would someone help me in finding the root cause of this issue and what can be done to avoid it.
There were no backups running when this alert was generated. As far as I'm aware, everything was idle.
I would appreciate any help.
Karan

Exception Message: ExecuteScalar requires an open and available Connection. The connection's current state is closed.
Based on the Error it seems the below for me
1. Either SCOM is unable to connect to the operationsmanager / operationsmanagerDW for its transactions on subscriptions
2. Or the SMTP server which your SCOM is using to relay emails has closed the connection.
So my suggestion would be you check the above for issues.
Gautam.75801
There were no network hiccups that I can see. Minimal disk activity. I've looked for any signs of database load, and haven't seen anything that jumps out.
Emails were going through just fine. These alerts get emailed to me, and if the SMTP server is 'closed' SCOM is usually quite sensitive and alerts about that too. I've seen it.
KB

"Airport Utility was unable to find your Airport after restarting"

Airport Express B has been working great for two years, and suddenly it can't be found in Airport Utility.
When I hard reset it, and re-set it up again, I go through the whole procedure, using the Utility to write the new settings : "The settings for this Airport Express have been successfully updated...waiting for Airport Express to restart" and at that point nothing happens - the light stays continuously green, no restart, and shortly afterwards I get the failure message "Airport Utility was unable to find your Airport wireless device after restarting".
I come out of Airport Utility, reopen it, and it can't find the Airport Express. Nothing. A £65 brick that has ceased to be, and this forum is full of people with similar problems. I've tried all of the fixes, including hard-wiring it using Ethernet, and again it goes through the whole procedure abut when trying to restart the AE, fails to find it.
Are Apple making any response to these issues ?

Thanks Martin - I can download it from the Apple website, according to this discussion :
http://discussions.apple.com/thread.jspa?threadID=1085243&tstart=30
My concern is that a) it may not work with an Intel MBP, and that it may break my Airport - totally. Could you let me know what you're running it on ?

"Airport Utility was unable to find your airport wireless device"

I recently bought an Airport Extreme to replace a D-Link DGL4300. My network is as follows: DSL > Modem > Airport Extreme > Ethernet and Wireless clients (wireless clients include my iMac and my wife's MacBook). This worked fine for about 2 weeks, until my wife's MacBook started having connectivity issues. I did a soft reset on the Airport Extreme, and . . . poof. No internet for anyone. I did a hard reset and used the saved profile that had previously worked (for at least my computer), and after the Airport Extreme restarted, I received the dreaded "Airport Utility was unable to find your airport wireless device". I have repeated this cycle several times with complete power-downs of the modem, the Airport Extreme and all clients, with no change in result.
What's odd is that even though Airport Utility can't find the Airport Extreme, my home network works fine (i.e., all clients can talk to an internal media server and each other), but there is no internet at all. Any ideas?

Alex Fisch wrote:
"Airport Utility was unable to find your airport wireless device"
Until you can complete the configuration process, try connecting your Mac to the AirPort Extreme with an Ethernet cable to see if that allows AirPort Utility to see the Extreme.

Security processor was unable to find a security header in the message. This might be because the message is an unsecured fault or because there is a binding mismatch between the communicating parties.

Similar Messages

Maybe you are looking for