Seeing controls in the dark

this is my first ever ipod, new video 80gb. I was using it in the car with a fm transmitter and when it got dark the screen came on when I touched it but i couldn't see the controls. surely these can be backlit can't they. i have set backlight on and 10 sec option but the controls are still un lit in the dark? can any one help
Thank you

Nope... the controls can not be back lit. But they are not too hard to memorize.
Regards--- jgurbisz
If I helped... please mark as helpful or solved. Thanks

Similar Messages

Seeing my iPOD in the dark

I haven't gone through all the posts so this may have been suggested before. It's all very well allowing the screen to light up for 10 seconds or so when you touch the control wheel.Wouldn't it be a good idea if the back light could be extended to the control wheel symbols so I could see what I'm doing in the dark.

Well it will of course. The next iPods will be touch screen versions, basically iPhone minus the phone and plus a hard drive. So by default the buttons will be backlit because they will be part of the screen.
They will never do it for current iPod because there is no hardware (LEDs, cold cathodes, etc.) behind the wheel to support it and next generations are almost sure to be iPhone like.
Patrick

Is there a way of connecting the ipad to the smart board in the classroom, so that the smartboard is the control, and the ipad is displaying what is on the smartboard? This is to help a visually impaired child see what is on the smartboard.,

Is there a way of connecting the ipad to the smart board in the classroom, so that the smartboard is the control, and the ipad is displaying what is on the smartboard? This is to help a visually impaired child see what is on the smartboard.

Absolutely!
Install Splashtop2 on the PC and enable it to be controlled or ran from iPad or Reflection to simply allow iPad to serve as PC unwired monitor. With Splashtop and an Apple TV connected, you use the smartboard as usual, yet the PC and iPad can see the same content. The impaired child can even interact with the Smart Board via the iPad as if he were writing directly on the big screen. Erasing functions can be done by touching the Smart Board manual controls. Several variables are in play that cause this lack of functionality:
    Apple won't permit PC software that infringes its proprietary apps.
    Smart Board companies refuse to develop iPad apps because they feel threatened and are being replaced by iPads
    School districts think Apple TV is meant for copyright infringement and could expose them to safe harbor lawsuits
    Network administrators make it impossible to login Apple TVs because they don't want the streaming occurring
    Classrooms are not able to keep up with the technology of using the iPad
    Clicker companies refuse to play with iPad because they see it as a potential threat to their core business clients
    Apple is not working as hard as it could to exploit its capabilities in education, thus losing money in iPad sales
The bottom line is that we educators and technology developers are hurting our childern with petty conflicts.

My iphone 5 suddenly wont fully boot...it stuck on the apple logo and goes of after 20 -25 secs and comes on by itself after a minute or two but still stuck on apple logo..also i am able to see a bit of lighting on the dark screen whenever it goes of

my iphone 5 on the ios 7.1.2 suddenly wont fully turn on...it gets stuck on the apple logo and stays like that for approximately to 90 secs then goes blank but I can see a bit of lighting behind the dark screen....it goes off by itself and comes on by itself trying to boot but still gets stuck on the apple logo after the dim light shows....when I connect to iTunes my phone can only be recognised only in recovery mode thus if I force it into recovery mode. My main worry is I don't have a back up of any of my data...on icloud I have just less than 2GB of my data which is as a result of incomplete back up...HOW CAN I GET THIS PHONE WORKING AGAIN WITHOUT LOSING MY DATA...if I can only just recover my data I would really appreciate it as I really need almost everything on it back...if I can only get retrieve my data and lose the phone I wouldn't mind at all....Anybody know how to resolve this??Kind Regards

Anyone have any suggestions? or is everyone else just as clueless as me !

Why can't I see the airplay icon in the music app or control centre on my Iphone 4 running ios7? I can see it in the movie app

Why can't I see the airplay icon in the music app or control centre on my Iphone 4 running ios7? I can see it in the movie app

I've seen something yesterday that says Airplay in control centre is only for Iphone 4S and onwards. It's frustrating when they take something away without any obvious reason. I'm going to change back to IOS6 until it's sorted out.
I also tried connecting to bluetooth and only once I'm connected does an icon show up in control centre. There's no direct way to connect to a device from control centre on the Iphone 4 from the looks of it.

HT1498 I rented The Dark Night Resises and I can not see it on my computer Itunes already charged me for the rental ofthis movies. Please either credit my account or let me know how this matter can get resolved.

I rented the Dark Night Raises yesterday December 22, 2012 It was charge on my Itune card, but I cant not see it on my computer please creidt me the cost of the rental or advise me on How we can resolve this matter.

We are all itunes users just like you. We can do nothing.
What do you mean "I cant not see it on my computer"?
You cannot fond the movie? Where did you look?
Did it download? Have you tried Store>Check for Available downloads.
The movie is there but it won't play?

The accursed little dark gray ball with white in the center and white arrows, either two or four, which seize control of the screen and move the text or pictures up, down, left, right and can be stopped only by finding the ball and clicking it. I want to

The accursed little dark gray ball with white in the center and white arrows, either two or four, which seize control of the screen and move the text or pictures up, down, left, right and can be stopped only by finding the ball and clicking it. I want to stop the thing permanently. Firefox 3.6 and 3.64
== This happened ==
Every time Firefox opened
== with 3.60

The accursed little dark gray ball with white in the center and white arrows, either two or four, which seize control of the screen and move the text or pictures up, down, left, right and can be stopped only by finding the ball and clicking it. I want to stop the thing permanently. Firefox 3.6 and 3.64
== This happened ==
Every time Firefox opened
== with 3.60

How do I prevent the Darker Shade Box (color shift) around Vector Objects when Printing

Sorry in advance for the novelette. I am absolutely mystified and frustrated and would love some help! I've been working on this problem for about 30 hours over the last 4 days to figure out what the heck is happening and cannot find an answer through various forms of research.
Basically, when I print a JPEG, I am getting this area (a box) of darker shaded coloring around my heart and love text. I've tested it a million different ways and am at a loss as to what the problem is ... is it an application problem, a color profile problem between my applications and printer, an improper way that I saved my file, etc.
Here is a photo I took of the image printed out (so it is slightly skewed from camera distortion):
The details:
(1) I create graphic art and sell it online. I save all of my printable art as JPEG files because of my customer base (diy hobbyists that print on their home printers without much knowledge base nor graphic design software).
(2) I use both Adobe Illustrator (AI) and Photoshop Elements 11 (PSE11) to design and save my artwork.
(3) I insert JPEG images into Microsoft Word 2003 documents to "test print" since most of my customers use home printers to print. Since most people have this basic software, it is a good gauge of the kind of print out they might get using the same or similar software.
(4) My PSE11 color profile setting is the default sRGB. I have test printed many times and I get the truest colors with this color profile.
(5) My AI color settings are normally also an sRGB color mode, but on occasion, I use a CMYK color mode if I am creating a larger document that I know the customer will need to take to a professional printer to print out.
(6) I do my home printing (for proofs) on an Epson Stylus Photo 1400 (which has the 6 color ink cartridges).
(7) Until this printing problem occurred on this test print out, I always used the "photo enhance" option when I designate settings for my printer via the Microsoft Word documents.
IMPORTANT: This is when I have the color shift?? or color rendering issues?? and it is the only time. If I use the regular ICM/ICC color profile of sRGB, the printing issue doesn't occur. Instead, I have a solid color background instead of this one with the strips of lighter color on the top and bottom. However, I can't control how the customer prints, so I need to feel confident that whatever color profile setting they use, they will not run into this problem. I even test printed the documents over at FedEx and the darker box/color shift did not occur.
(8) The document in question only has 3 sets of objects: the heart, the solid colored rectangle colored background and the text. All 3 objects are vectors, they are at 100% opacity and there are no "special effects" applied.
(9) The image was entirely created in AI this time and exported as a maximum quality JPEG file, although you will see below that I tried many ways to create and save the file so that I didn't have the color band borders on top/bottom.
(10) I regularly use AI for part of my art, then I drag it to my PSE11 open document and it becomes a Vector Object (it cannot by copying/pasting into a PSE11 document). I also regularly export AI images as PNG files, then insert them into an open PSE11 document. This printing issue has not occurred until recently. Here is an example of a very complex AI image I created, then inserted into PSE11 just to add the background (the Teddy Bear and books are AI vector objects) that were exported as PNG files then inserted into PSE11 to integrate with the background image - I test printed with Photo Enhance and had no printing issues:
So, from the research I have done, it looks like it is a color rendering or color space issue with conflicting color profiles in the same document. I checked my color profile settings and both sRGB and CMYK were set to embed ICC color profiles.
I tried changing AI settings to Preserve Numbers (ignore linked profiles) for CMYK, but that didn't work.
I also checked and made sure that not only the document setup showed the sRGB color profile, but that all the objects within the document also were converted to sRGB as well for consistency. That didn't work.
I tried converting the document to CMYK along with the vector objects. That didn't work.
I tried saving the heart image as a PNG file alone, the "love" text as a PNG file alone, both the heart and text together as a PNG files alone. Once saved as PNG files, I inserted them into an open empty PSE11 document - as I normally do. I then added the background color I wanted. That didn't work - the print still showed the color changes.
I tried dragging each vector object separately and even as a group and got the same color change issue when printing.
I tried "expanding" and "outlining" the text before exporting as JPEG, before exporting as a PNG and before dragging as a vector object into PSE11. Expanding the text did not help the situation.
I tried exporting as Adobe PDF, then opening in PSE11, then resaving as JPEG. That didn't work.
I tried flattening transparency (even though there is no transparency in the AI file). That didn't work.
I tried rasterizing the image. That didn't work.
Thinking that the file might be corrupt, I started from scratch and redesigned the same heart and love text. Unfortunately, I had the same problem as before. At this point, my AI started becoming buggy and would not open new files. It happened repeatedly and I decided it was best to uninstall and reinstall AI (and maybe that would fix the problem).
I created just the heart in AI, then inserted it into an open PSE11 document (both after exporting as PNG and also by dragging as Vector Object from AI). It seemed to work. I could both drag the vector into PSE11 from AI and export from AI as a PNG, then insert into open PSE11 document with a background color - and it printed a solid background.
So, I thought that reinstalling and setting back to defaults worked. But, then I added the love text around the heart and tried exporting as JPEG files and the same problem continued to recur. Whether I dragged as a Vector object into PSE11 (the heart object and love text separately and also another time with the vector objects dragged as a group) or saved them as PNG files and inserted into PSE11 - I got the different shades of color on what should be a solid background. I even tried saving the PSE11 as a PSD file first, then resaving as JPEG and I tried saving as PNG and printing and this didn't help solve the problem.
I really think it is some color conflict issue but I can't figure it out. I am definitely not very knowledgeable about color profiles and how to sync all my devices, however, as I mentioned, this was not an issue until recently (and I think??? I recall changing the CMYK setting from Preserve Numbers to embed color profile a month or so ago - however, it should have been solved when AI went back to its defaults upon reinstall).
The reason I believe it is a color rendering/color space issue is because I could see the color output when I saved the JPEG with CMYK color profile versus sRGB color profile and the sRGB colors were much richer, not surprisingly. The top and bottom colors matched the sRGB printout and the middle darker box section matched the CMYK printout.
I am sure it is something fundamental or simple and I am completely overlooking it. I wish it were just a transparency issue, because people know how to fix or do workarounds for it. But, there are no vector objects with any transparency ...
If I missed some detail, I apologize. Any help would be a dream come true at this point! lol
Thank you!

Okay, I got motivated to try again. From doing a bit more research on troubleshooting AI printing problems, the Adobe article talks about print drivers. It was advised to uninstall and reinstall the print driver if the printing issue persists. So, I did. Unfortunately, I still had the same result after reinstalling and trying a test print! Ugh.
So, as Jacob said upfront, I seem to have an overactive print driver that is trying too hard (and it is a non-postscript printer which I realize is part of the problem).
There are so many variables in my situation as to how I create art and save/export art. I sometimes work solely in AI, sometimes solely in PSE and sometimes I use both programs to create. Consequently, I will:
(1) export directly from AI as JPEG if I am not adding PSE11 artwork.
(2) export directly from AI as PNG if I plan on inserting that image into PSE11 to add to artwork I have created in PSE11.
(3) drag vector objects as a Smart Objects directly from AI to PSE11 to add to artwork I am creating in PSE11 if I know I will playing with the vector object and resizing in PSE11.
So, I did a test print using scenario 2, where I inserted the heart and love text PNG (AI created vector object) into an old PSE11 document. This old document already had a vector object from AI with a solid background and I knew it printed correctly. So, after inserting this new PNG from AI into this old document, it printed correctly using the photo enhance mode.
However, I haven't had a chance to actually create new art in the older AI files (that I know print properly), resave as something else and try another test print (either by exporting as JPEG and printing in Word or by exporting as PNG file and inserting into PSE11 document, then saving as JPEG and printing in Word).
After testing the different possibilities of ICM settings within my printer, I found that the JPEG images printed out with the truest colors and best quality if I simply selected "no color management" from the printer. Shocker, huh? lol
MY SOLUTION: So, what I think I will simply do is add an instruction sheet with the printables I sell, explaining that the color profile setting should never be handled by the printer so make sure to turn off color management by printer (and if they feel they must use the printer for color management, make sure the setting is sRGB since I embed that color profile in my JPEG's).
Edited to add: Since my issue was never about how I could print a successful image (I knew I could simply change the color profile settings), but rather about how to make sure that customers would get consistent and high quality print outputs of my digital images, this seems like the best approach.
I don't think I will every really know exactly why I am now getting color shifts in the "photo enhance" mode when I did not have this problem a couple months ago - applying the same methods of creating artwork. I was concerned that I was saving/exporting using incorrect or mismatched color settings or something of that nature. However, since I went through the process of making my color spaces the same for everything, and I still have issue, clearly that is not the culprit. The only thing I can do to solve the problem and it is a straightforward solution anyway -> is to educate the buyer on how to print successfully (don't use photo enhance! ha ha).
Thanks again to everyone who chimed in and offered advice!

Screen looks glow in the dark

My son pushed some buttons not sure exactly what he has done but my screen is black and everything else sort of glows in the dark. Please help!!!

The other thing it could be is another setting in the same Universal Access panel, also under Seeing - the Display settings should be "Black on white", but may have been switched to "White on black"
It's possible to switch back and forth by hitting control-alt-command-8 all at the same time. Which doesn't sound too likely to get hit by accident, but it happens to pretty much every Mac user at some point!

User-developed Fan Control for the S10(e)

Hello and welcome.
When you've searched the internet and found this thread, it's possible that you are an owner of a Lenovo Ideapad S10 or S10e which has a little problem with the behaviour and/or the noise of the fan. In this post you will get all the informations you need to handle this problem for yourself. It should also be the same on every S9/S9e.
Just a few comments before we begin:
This is not an official support or solution by Lenovo.
We are just normal users as you are, but we get rid of the fan and wanted to find a way to handle it. So if you want to try anything of the methods described here you have to know that you'll do all this only at your own risk. We are not responsible for any damages of your device. You should only use these methods if you know what you are doing.
Please note that this thread is only for discussing, improving, trouble shooting and perhaps extending the fan control utilities. Any general complaints about the fan problem itself should be placed in the original thread right here: http://forums.lenovo.com/lnv/board/message?board.id=IdeaPad_Netbook&thread.id=795. It already has 80+ pages (the link goes to the first page) and it is better to exclude all the fan control stuff because there it's very difficult to keep an overview.
Here you may post all of your questions, ideas/brainstorming, concerns, thanks and so on and you are really invited to participate and be an active member.
In this first part of this post I'm going to summarize all information about using a fan control utility. For any newbie it will be enough to read this post to get all necessary information. The second part does the same for developement of fan control utilities as we still have no known or working fan control utility for Linux, Mac OS X and other OSs I've forgotten - for now.
For getting started you need a S10 or S10e with an up-to-date BIOS. For the S10 it's the 90 67, for the S10e the 66.
The battery issue
Under very specific circumstances - that we haven't figured out yet - it might happen that your Lenovo S9/10(e) no longer detects the battery while using S10FanControl or S10Fan. It might occur after 2 minutes, it might occur after 2 months, it might never occur. It does not occur using Notebook Hardware Control.
It can be solved by removing the battery, waiting 10 seconds and put it back in. Then the battery is re-initialized and the detection works again.
S10FanControl - Windows
The first utility is S10FanControl created by user dresslerc. The current version is 1.0.0.1, available here: http://www.mediafire.com/file/yd5xmnrnijf/S10FanCtrl1.0.0.1.zip. After you've downloaded it you just have to extract it and start the .EXE in the "Release" folder. Here are the notes and the description dresslerc posted right here:
Everyone,
I've uploaded a version which everyone can use to test with. Remember this is still a TEST version although I think it works for the most part. It should work both on the S10/S10e.
Please install the .NET Framework 2.0 or later first.
Then click here to download the exe: http://www.mediafire.com/?jlg2enkjdxn
Once downloaded, extract the files and hit hte S10FanCtrl.Exe. Once this program launches you should be able to control the fan. Keep in mind that if you lower the fan speed then it'll take upto 30 seconds before the S10 registers the change, so be patient.
I've only tested this on the latest BIOS 59. I am sure it will work on the 57 as well but the individual speeds might not work properly on that version. Please try it out and report back.
The only issue that I heard so far is that occasionally the fan will kick in regardless if in Manual/Smart Mode. Also the temp it shows may not be accurate. If you find any other issues please let me know what they are so I can attempt to fix them.
Once we have all the kinks worked out then I will release the source.
Heres a quick Video: http://www.youtube.com/watch?v=_PKl70ZgmFg
REMEMBER: USE PROGRAM AT YOUR OWN RISK!!! I AM NOT RESPONSIBLE FOR ANY DAMAGES THIS PROGRAM MIGHT CAUSE.
Application Use:
BIOS Controlled - Fan is controlled by the BIOS
Smart Mode - Fan is controlled based on the conifguration in the options. You can set the threshold here at what temp you want the fan to kick in...
Manual - Fan is controlled manually by the slider.
If you want to have the program startup automatically, then place a shortcut of the app in the PROGRAM FILES -> STARTUP folder. Then you may want to go to the options and make the application minimize at startup.
Edit:
It seems there are some issues with the app and the S10e or previous BIOS versions. Will post a fix asap.
The source code for S10FanControl is available here: http://www.mediafire.com/?sharekey=7a3fb99d33817c08c2b435915e8821d7e04e75f6e8ebb871, written in Visual Basic .NET 2008.
S10Fan - Windows
The second utility is a tool written by user slash:
Hi guys,
Well it looks like Lenovo dropped this matter after all. Anyway, I have here another fan controller to add to the bunch. I have been using it for some time now without any problems. It is for both S10 and S10e.
What the program does is basically the same as others. The S10's fan speed is controlled according to the ACPI thermal zone temperature. By over writing the values which resides at offset 50h of the EC register at an appropriate timing, the ACPI thermal zone temperature is over ridden. The program is written in C and uses WinIo created by Sysinternals. The GUI version is available now.
It should be noted that the fan speed temperature thresholds differs with BIOS version. For 14CN67WW and 14CW90WW the fan changes speed at temperatures 60c, 65c, 70c, and 80c. Furthermore, the BIOS will automatically shutdown the S10 if the temperature reaches 90c.
The program has a fail safe mechanism that automatically disables itself if the actual ACPI thermal zone temperature goes above 85c. This allows the BIOS to regain control and the fan will work as intended by Lenovo. If the temperature drops below 85c the program will take over control again.
To run the program, you will need administrative privileges.
Known working BIOS versions: 14cn58ww, 14cn60ww, 14cn67ww, 14cn90ww
The program will work with any BIOS version as long as the BIOS uses the 50h EC register readouts to control the fan.
build 2009.05.24
Higher priorities for EC commands.
Usage: The program will run in the system tray. Double click or right click and use the menu to open the program. To determine the BIOS temperature thresholds, use the 'Setup' button. To run at boot time, place a short cut in the startup folder.
http://www.mediafire.com/file/njhz0icym2t/S10Fan.zip build 2009.05.23
Usage: S10Fan.exe
Added GUI.
build 2009.05.17
Usage: S10Fan.exe 60 65 70 80 70 75 80 85
S10Fan.exe test
The first 4 values are the BIOS temperature thresholds, the latter 4 are new thresholds that we want to over ride with. To determine the BIOS temperature thresholds, use the 'test' option.
build 2009.03.16
Usage: S10Fan.exe 70 75 80 85
-Slash
For updates and newer releases please check slash's post: http://forums.lenovo.com/lnv/board/message?board.id=IdeaPad_Netbook&view=by_date_ascending&message.i...
Notebook Hardware Control - Windows
The third utility is a profile for Notebook Hardware Control. I've adapted it from a profile for the Lenovo N500 which I've found here: http://nhc.yourcopy.de/overview/. With the manual for creating the profiles that can be found here: http://www.notebook-treff.de/board/database/hilfsprogramme-f%C3%BCr-nhc/92-how-to-create-an-acpi-fil... I was able to change the ACPI commands to work on the S10(e).
Installation and setup is divided in two steps. The program Notebook Hardware Control (NHC) is available at http://www.pbus-167.com/. Install the program, but do not start it for now. Then you need my NHCConfig utility, available here: http://forum.eeepcnews.de/download/file.php?id=1476. It detects your model number and BIOS-version via WMI and writes a proper S10(e) profile to the NHC acpi directory. The GUI is German if you have a German Windows and English if not. Additional languages can be added.
After you've extracted the ZIP-file you have to start the nhcc.exe (requires .NET Framework 2.0). At first a message appears that you use the program at your own risk. Then you can choose if you want to apply your own settings (experts) or if you just want the program to run with my defaults (newbies). In the settings window you can see your system details on the left, you can set up your thresholds in the middle and you can set the fan speed you want on the right. Then click on execute.
Now start NHC. Go to the "Settings" tab and click on "Show all NHC options and settings". Then a few more tabs appear. Go to the "ACPI" tab and check if the "ACPI Control System" is running (if everything works, the message "ACPI Control System running" will appear, otherwise it says "ACPI control system is not yet configured for this system"). Now click on "Show ACPI Control System details".
Here you can change the temperature values the fan control depends on (the settings from NHCC are the default values). On the bottom of the window you can see the "Current CPU temperature". That is the value you have to deal with. In general it has a value of around 60°C. In the middle you can see four user editable temperature values. You can leave the values as they are if everything works. The on/off values are responsible for the temperatures at which the fan starts running and stops again after cooling the device. The level values are responsible for the fan speed, for example you can set the off_level higher to let the fan run all the time at the lowest level, if the values do not fit for your device or whatever.
You can switch between NHC and BIOS control by disabling or enabling the "ACPI Control System" or by closing NHC.
Q:
A:
With every utility it is possible that it takes some time until you see an effect after you've started the program. Any failure of the programs should be no big problem because the only thing that should happen is that the BIOS controls the fan. Another issue that might occur due to the way the fan is controlled is that the fan may start running for a very short time and it looks like the fan control has lost control. The fan should stop immediately or at least after a few seconds.
Keep in mind that running the S10(e) with a fan control means that the S10(e) has to deal with higher temperatures. That could mean that the device will not last for 10 years but only 9 years (who uses a netbook so long...?). In every case you need a tool for monitoring your cpu temperature. We know that especially Core Temp 0.99.5 and Real Temp 3.00 do a very good job. That is important because the temperature values you need to set up the fan control are different from the values reported by the cpu sensor, they are between 15°C and 20°C higher. A normal temperature reported by the monitoring should be around 40°C, with the NHC default values the fan starts running at 52°C and stops at 38°C.
Q:
A:
Q:
A:
END using fan control
BEGINNING developing fan control
Controlling the S10(e)'s fan is a litte bit difficult because it looks like there is no way to control it directly. But it is possible to manipulate the temperature the BIOS fan control depends on. As long as the built-in fan control thinks that the cpu is cool enough the fan stays off. And that is exactly the point where we can attack.
The fan control depends on a field called RTMP in the memory of the embedded controller. It can be accessed via "_SB.PCI0.LPCB.EC0.ERAM", the offset of RTMP is 0x50 (hex) or 80 (dec). It is a direct I/O read/write. The complete NHC command for reading the value is: ACPI.FIELD.ReadByOffset("_SB.PCI0.LPCB.EC0.ERAM", ref value, 0x50, 8) with "value" as the variable which gets the value.
What program logic do you need? You need a timer or something else that conducts an always-refresh cycle. It sounds very easy: You read the value, manipulate it and write it back. And it is that easy, you just have to keep some things in mind.
This refresh has to be done very often. The procedure must be very thin and quick. Also the bus that is used to communicate with the EC is a problem, but since the S10e BIOS 66 it became a minor problem for me because it looks like the built-in fan control now depends on some kind of average value over the last few seconds and it doesn't really matter if one write-cycle is failing.
The read-event must be placed before the write-event. Otherwise you just read your manipulated value. The field is filled by the system regularly, so you just have to test if the read_value is different from the written_value, then you know that the field was filled with a "fresh" value. Like "if read_temperatue <> written_temperature then real_cpu_temperature = read_temperature else do nothing".
About the values you have to write back... you will have to test and play a bit. My experience is that you can select three fan levels, starting at 59°, 62° and 70° - at least with the NHC profile and my S10e it's like that. It's some trial 'n' error. My fan stays off at < 59°, but you should select a very low value for fan_off like 30°. In my opinion it switches off much faster the lower the written value is. But it's just a feeling, I haven't measured it.
Q:
A:
Q:
A:
Perhaps some users from countries with other languages than German and English can add tags for "fan", "control" and "noise".
Note from Moderator: Minor edits in title and disclaimer.
Message Edited by JaneL on 04-25-2009 02:32 PM

Great opening post Carsten!
The latest bios:
http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-71252 (BIOS 66)
The FSB can be reduced from 133MHz to 100MHz using SetFSB, this also reduces the heat:
http://www13.plala.or.jp/setfsb/
clockgen = SLG8SP513V
If you add a shortcut to the startup folder the program will start at startup. Under properties you can change the target to:
"C:\Program Files\SetFSB\setfsb.exe" -s100 -b1 -cg[SLG8SP513V] -w20
So it starts with a FSB of 100Mhz, in the background, with the right clock generator, after 20 seconds.
Message Edited by quazar on 04-25-2009 05:07 AM

How can I get rid of the dark area on top one third of my iphone screen which spoils my background image?

How can I get rid of the dark area on top one third of my iphone screen which spoils my background image?
It seems this problem is caused by the software to increase the readibility of upper letters (clock battery etc.) It be nice to leave us the control of choosing background letter color too if we are using brighter images or darker images.
I'm using iphone 4s and it appeared after I updated to new patch. 7.1.1.
Thanks,
Cem
I do not know how to move topics from sections of forum so I apologise for duplicate post.
https://discussions.apple.com/message/25594879#25594879

Photo added.

Why does my iPhone 5 take very grainy flash photographs in the dark will a hard reboot be safe to do to try to fix or is it a hardware issue?

Why does my iPhone 5 take very grainy flash photographs in the dark will a hard reboot be safe to do to try to fix or is it a hardware issue?
And By hard boot I mean holding the home and power button down at the same time for 10 seconds or whatever
I see other people have these grainy flash photographs if you try to take a picture in darkness the picture comes out very dark and grainy I thought the software would ultimately fix this but it's been going on for over a year I usually take my photographs in daylight but I need this to be fixed
If it is a hardware issue I hope Apple will replace my iPhone 5 because I was just waiting for one of the iOS updates to fix it I bought my phone in November 2012 its the iPhone 5
Please help or advise if you can was this just a software or hardware issue I know Apple was aware of it but I was advised that iOS update would fix it but obviously not
Is it safe to do a hard boot on my iPhone five by holding the power and home button at the same time for 10 or 20 seconds I saw someone said that fixed there's at least temporarily
I'm typing this on my iPhone five right now why do the words go off to the left and right no matter if I hold the phone vertical or horizontal the words bleed off to left right so for me to proofread it I have to move my text left to right to proof read it
Thank you

The flash on a smartphone camera is tiny. It only lights up a very small area right in front of the camera. It won't light up the whole scene.
Have you seen the size of the flash on a professional camera? Even they can't light a whole scene in the dark.
Fact is, a smartphone camera is not capable of taking good photos in the dark, even with the flash.
You'll need to buy and learn how to use a professional, dedicated SLR camera to be able to take good photos in the dark. It is not easy.

Can the position and szing of a control element in a View be controlled from the ViewModel?

Is it possible to change the position of a control, say a label, as a response to some action/operation from the ViewModel? Like if one response to something is true then place the label in the top left corner. If false, place the label
in the lower right corner. I realize you could have a label in each position and just set the visibility. But can the position and sizing of said label be controlled from the View Model? What would be a sample coding of this? would
it be in the xaml or combination of a method in the ViewModel and the xaml?
Rich P

First off Rich, say TextBlock to yourself ten times.
Use a TextBlock rather than a label.
There are a bunch of different ways to do this and the easiest is to have two controls whose text is bound to the one property.
Bind the Visibility of each to another 2 properties in the viewmodel.
Collapse one and Visible the other.
The reason for that is that it's easier.
Technically, you could put one textblock in a grid and use margin to control this. You could animate x y co-ordinates and move the textblock mysteriously across the window if you put your mind to it.
Or you could put it in a row/column "cell" of a grid and change which cell it goes in - but that would involve some mechanism like messaging from the viewmodel to the view and is not really ideal if you can avoid it.
I'd have a pair of textblocks, here's one:
<TextBlock Name="TopLeftMsg"
Text="{Binding Msg}"
Visiblity="{Binding TopLeftVis}"
Both would bind to a public string property msg in the viewmodel.
They each get their own public visibility property and that'd be switched between Visibility.Visible and Visibility.Collapsed.
Sizing of textblocks is best fitted to content because all you see is the text.
Textboxes are arguably different because you can see the things.
Hope that helps.
Recent Technet articles:
Property List Editing;
Dynamic XAML

How to add a field in a table control of the subscreen 6103 of tcode f-03

hi abap gurus....i m new to abap and this is my first post ..i m hoping for a reply soon as it is urgent....
my requirement is to add a field PAYR-CHECF to a table control of the subscreen 6103 of tcode f-03

Hi,
Please see documentation of enhancement MM06E005 (transaction SMOD).
Userexit EXIT_SAPMM06E_016 is a component of enhancement MM06E005.
With that enhancement, you can
-   Maintain/supply your own customer fields
-   Update your own customer-specific tables
You cannot:
-   Change standard fields
-   Change data that depends on the document header in the items
-   Change data that depends on an item in the document header
Please have a look at Business Add-In (BAdI) ME_PROCESS_PO_CUST.
Regards,
Edit

My ipod app no longer works. Everytime I go to open the ipod app it stays open for a second and then shuts down. I am not able to get anything to play either through the standard ipod controls or the multitasking control panel. I'm sure there will be an u

my ipod app no longer works. Everytime I go to open the ipod app it stays open for a second and then shuts down. I am not able to get anything to play either through the standard ipod controls or the multitasking control panel. I'm sure there will be an update soon to correct this, i just wanted to see if anyone else was having the same problem.
wen i open ipod in my iphone ,, it gets stuck ,, and get backs to the menu ,,, and doesnot play anything ,, not video nor song

If your phone is not officially unlocked by the carrier in the UK, you can not use the phone using another SIM, unless you modify the software or the SIM, which can lead to unexpected results, such as non functioning apps.
Unauthorized modification of iPhone OS has been a major source of instability, disruption of services, and other issues
Problems resulting from those modifications can't be discussed in these forums, due to the Terms of Use

Seeing controls in the dark

Similar Messages

Maybe you are looking for