Seeking solution for ip cameras
hi all,
i have been assigned a project to install 20 ip cameras at 7 different locations .... out of 7 locations one location would be considered as head office .. the data of all 7 locations would be stored at head office ... i humbly request you to guide me in the selection of cisco routers for internetworking between these locations .... i will be greatful if you provide me network diagram for this solution ..my email id is [email protected]
thanking you in anticipation
With regard to question on which routers may be best for this scenario, please take a look at:
http://www.cisco.com/cisco/web/solutions/small_business/products/routers_switches/small_business_routers/index.html -> the RV220W may be a good fit for all locations:
http://www.cisco.com/en/US/products/ps11025/index.html
You may want to get hold of a not for resale (NFR) unit to test the head end with video + internet mix traffic flows (I assume it won't be just video running on the network), and performance will also depend on what level quality of video you are recording and sending over the WAN/VPN. Please email me ([email protected]) with your State and I'll provide a local contact to get an NFR unit.
Thanks,
Leah
Similar Messages
-
Seeking solution for RAW to jpeg conversion on 1TB disk[s] of images
Please read fully
Greetings,
I have a bit of a dilemma as most might have as well. I have about
3.5TB of RAW images in various directories and seeking an automated
way to convert RAW to jpeg on numerous directories...and go get a
coffee while the process is working (maybe have a nap or two lol)
For many months I have searched for a solution that takes the source
disk (yes disk and not directory by directory) and implements a NEF to
jpeg conversion placing the destination directory on another hard
drive or a separate directory keeping the same source directory
structure. So at the end of the day I would have full sized jpegs and
PSD's in the same directory structure as the source. That make sense?
I have been in other forums and asked but the solutions were using the
typical Photoshop solutions and it does not make a dupe directory
structure as the source.
Any solutions? Ideas?
Thanks,
D.S. HathawayThis is what I'm trying to do. It seems the Image Processor does not handle multiple directories at once.
MainDrive (source)
|
|
1234_flag_images
2345_ball_images
3456_table_images
etc
In the directory 1234_flag_images contains
1234_flag1.nef
1234_flag2.nef
1234_flag3.nef
WIP <---directory Work in Progress contains
1234_flag1.psd
1234_flag1.jpg
What I am seeking is the above source to be converted to jpeg and
placed onto another dirve/folder/directory with the SAME directory
tree. It should look like:
Another Drive/folder/directory etc (destination)
|
|
1234_flag_images
2345_ball_images
3456_table_images
etc
In the directory 1234_flag_images contains
1234_flag1.jpg
1234_flag2.jpg
1234_flag3.jpg
WIP <---directory Work in Progress contains
1234_flag1.psd
1234_flag1.jpg
Make sense?
Isn't there anything out there to handle multiple
(read 100s) of folders/directories and make a conversion as stated
above?
Thanks again,
d.s.hathaway -
Solution for Multi Cam Crashes on Audio Sync?
I am having major issues when trying to create a multi-cam clip by syncing audio. It will process a few clips and then I will get a serious error message. I would say it occurs on about 8 of every 10 attempts. At first I thought it was because I was selecting too many clips (I'm shooting a doc and sometimes need to sync 100 plus clips from multiple cameras to multiple audio tracks) But it also crashes when I try to sync a single audio track to only a handful of clips.
I'm on an I-Mac mid 2011. I've updated the OS to Yosemite, no luck. Tech support said to upgrade my RAM to 16g, I did that and it still crashes. I've re-installed the software, still crashes. Reset the preferences, still crashes. I've installed the software on a new administrator account, still crashes. I've changed the renderer to software only, still crashes.
I also have a Macbook Pro Retina 2013 running OS 10.8. I've tried creating multi-cams by syncing audio on that computer as well. Still getting crashes. I've tried all the changes on the lap top that I did on the I-Mac (change renderer, re-install, new administrator, reset preferences, etc) Still getting crashes.
I've tried different projects, different footage, different drives, placing the media on the internal hard drives. Still crashes.
I'm assuming there must be a conflict of some sort, but can't figure it out. Tech Support has been less than helpful (when I can reach them) and I'm hoping someone knows a solution. I just moved to Premiere Pro and this issue might make it a non-starter for me.
Any thoughts would be appreciated.Update: I just happened happened to have a pair of ath m50s lying around.... put them on and I can see that in the multi cam sequence, I can hear only out of the left ear... once I drag and drop something to my timeline the audio's good again...
Sorry for this question... operator???
I shoot tech videos on YouTube and I edit my own videos, so I guess I am the operator & observer here...
Am shooting a tutorial...
Cam 1 - My Camcorder that shoots the phone
Cam 2 - Actually a screen recorder that records the steps on screen & audio from webcam
Audio - Blue Spark Digital recording to audacity
Now if I merge Cam 1 & Audio or Cam 2 & Audio alls fine... I can check the audio meters and everythings the same as before
But if I create a multicamera sequence then the audio output is about 20% lower (and no Premiere's not using the audio source from Cam1 or 2 here since they are too low and am 100% sure its not either of those)
I guess am messing up something but am unable to identify what..
Syncronize Point - Audio
Track Channel - 1
Sequence Preset - Automatic
Audio Sequence Settings - Camera 1
Audio Channels Preset - Automatic (or Mono since my Blue Spark records in mono)
Camera Names - Enumerate Cameras
Any Idea where am messing up?
Ash
Message was edited by: C4ETech -
Solution for the Camera Raw 8.2 update installation problem
Hi.
Adobe Camera Raw 8.2 for CC & CS6 was released two months ago.
http://blogs.adobe.com/lightroomjournal/2013/09/camera-raw-8-2-and-dng-converter-8-2-now-a vailable.html
But many people got problem in updating Camera Raw 8.2.
I tried to inspect the update application and simply found a workaround.
Adobe Camera Raw 8.2 for CC & CS6
Unzip and replace "Camera Raw.8bi" in the file formats plugin folder.
For Windows 7 ~ 8.1, the path is "C:\Program Files\Common Files\Adobe\Plug-Ins" => "CC\File Formats" or "CS6\File Formats"
CC & CS6 x64 .7z (13,088KB) - https://drive.google.com/file/d/0BwCp0TDkNkHYVUZzSlpKenNSajQ
CC & CS6 x64 zip (14,962KB) - https://drive.google.com/file/d/0BwCp0TDkNkHYUW9zeVNLMXJIRFU
CC & CS6 x86 .7z (12,633KB) - https://drive.google.com/file/d/0BwCp0TDkNkHYNU5GTEhZbmF5eGc
CC & CS6 x86 zip (14,254KB) - https://drive.google.com/file/d/0BwCp0TDkNkHYeE1PRThIejQyTDg
* Extracted from http://swupdl.adobe.com/updates/oobe/aam20/win/PhotoshopCameraRaw8-8.0/8.2.67/setup.zip
Adobe Camera Raw 8.2 Camera & Lens Profiles for CC
Unzip files in CameraRaw application folder.
For Windows 7 ~ 8.1, the path is "C:\ProgramData\Adobe\CameraRaw".
.7z (12,387KB) - https://drive.google.com/file/d/0BwCp0TDkNkHYdWFyZXRwNG1XeUk
zip (17,830KB) - https://drive.google.com/file/d/0BwCp0TDkNkHYdl82bzluSnNCSU0
* Extracted from http://swupdl.adobe.com/updates/oobe/aam20/win/PhotoshopCameraRaw8-8.0/8.2.67/setup.zip
Hope this is helpful.
Thanks.
New Camera Support in Camera Raw 8.2
Canon EOS 70D
Canon PowerShot G16
Canon PowerShot S120
Casio Exilim EX-ZR800
Fujifilm FinePix HS22EXR
Fujifilm FinePix HS35EXR
Fujifilm FinePix S205EXR
Fujifilm X-M1
Leica C (Typ 112)
Olympus E-M1
Panasonic Lumix DMC-GX7
Panasonic Lumix DMC-FZ70
Panasonic Lumix DMC-FZ72
Pentax Q7
Pentax K-50
Pentax K-500
Sony DSC-RX100 II
Sony A3000 (ILCE-3000)
Sony NEX-5T
New Lens Profile Support in Camera Raw 8.2
Sony E 35mm F1.8 OSS
Hasselblad LF16mm F2.8
Hasselblad LF18-55mm F3.5-5.6 OSS
Hasselblad LF18-200mm F3.5-6.3 OSS
GoPro Hero 3 Black Edition
GoPro Hero 3 Silver Edition
GoPro Hero 3 White Edition
Leica TRI-ELMAR-M 16-18-21 mm f/4 ASPH.
SIGMA 18-35mm F1.8 DC HSM A013
SIGMA 120-300mm F2.8 DG OS HSM S013
SIGMA 30mm F1.4 DC HSM A013
SIGMA 60mm F2.8 DN A013
SIGMA 17-70mm F2.8-4 DC MACRO OS HSM C013
SIGMA 35mm F1.4 DG HSM A012
Nikon 1 NIKKOR 32mm f/1.2
Sony DSC-RX1RInteresting. How much is accomplished in the 8bi file without reference to camera-specific profiles? There are some camera profiles that appear to have been added in acr updates. for example there is a folder <Canon EOS 70D> in <C:\ProgramData\Adobe\CameraRaw\CameraProfiles\Camera> (win 7) that contains five profiles (Faithful, Landscape, Neutral, Portrait and Standard). Would acr be able to process 70D raw image files without these profile files?
-
Seeking solution for converter!!!
I have a bunch of questions that need to be taken care of
like I want a converter for files to play on my mobile in 3GP
format and also need to convert my audio files that are in my CD to
my mobile ringtones.Can I get any software/site that can provide me
a good solution?It is not freeware but i am using total video converter :
http://www.download.com/Total-Video-Converter/3000-2194_4-10429299.html
It works fine -
Seeking solution for css and js making client very heavy around 800KB
I have developed GUI using web dynpro,
deployed the application in enterprise portal,
when i save the web page in local machine from browser(IE),
the HTML + css+ js file size comes around 700-800KB.
How can i reduce this so that i can use it in internet.
For internet application noone can afford more than 40 KB in client, Please any solution to the above problem ASAPDear jian
The css and js are around 500 KB.
These files get downloaded only when the request is for the first time.
So first time hit will be time taking but from the next time it will be fast.
If u can check and tell the file sizes of css and js of your application, then i can compare with mine.
But generally web applications should be very light in size.so , should i go for struts and can u give me the
advantages and disadvantages of web dynpro against struts.
Web dynpro pages are rendered in client browser ? and which framework does it follow ? is it ajax or ????? -
I bought iPhone 3GS(Used) recently and updated ios 6.1.3 my iPhone is taking blurry Pictures through basic default Cam app.Can anybody please let me know any solution for this?
Basic troubleshooting steps right out of the user guide are restart, reset, restore from backup, restore as new. If you've been through ALL the steps and you still have the problem, then you'll need to bring your phone to Apple for evaluation.
-
I want to download pictures to my iPad 4 from a memory stick pro duo. There are no cord connections for the camera and the USB dongle requires too much power through the camera connection kit. Any good solutions?
Another way. You can use a USB flash drive & the camera connection kit.
Plug the USB flash drive (works the same with an SD card) into your computer & create a new folder titled DCIM. Then put your movie/photo files into the folder. The files must have a filename with exactly 8 characters long (no spaces) plus the file extension (i.e., my-movie.mov; DSCN0164.jpg).
Now plug the flash drive into the iPad using the camera connection kit. Open the Photos app, the movie/photo files should appear & you can import. (You can not export using the camera connection kit.)
Cheers, Tom -
How to delete photos from camera roll only, let the rest remain in albums? Is there any no-PC or no iTunes solution for this?
If these are albums, you created on your phone, using pics in your camera roll, you delete the pics from your camera roll & they will be deleted from the albums as well. The albums don't actually contain any photos, only pointers to the actual photos, which are in your camera roll.
So, the answer to your question is no. -
Seeking a solution for synchronization of sequences in expdp
Hi all,
When i am exporting tablespaces from a live database, first the tables are being exported and then the sequences. and while these sequences are being exported, as this is the live database, the sequences are getting modified because of new insertions. So i am getting a conflict with sequences not being exported correctly.
I am using Linux OS with oracle version 10.2.0.4
Please provide me a solution for this.
Thanks & Regards,
Ravi kumarSequences get exported before the table data. I find that kind of annoying too that the sequences can be behind the data after an import. To get around this problem I run the following to create a script that will regen the sequences. Do this any time after the export is complete and you will have no problem.
set linesize 300
set heading off
set trimspool on
set trimout on
set pagesize 0
spool regen_seq.sql
Select 'DROP SEQUENCE ' || sequence_owner ||'.' || sequence_name || ';' || chr(10)
||
'CREATE SEQUENCE ' || sequence_owner ||'.' || sequence_name ||
' MINVALUE ' || min_value ||
' MAXVALUE ' || max_value || chr(10) || ' ' ||
' INCREMENT BY ' || increment_by ||
-- ' START WITH 1' ||
' START WITH ' || last_number ||
' CACHE ' || DECODE(cache_size, 0, 20, 1, 20, cache_size) ||
-- ' CACHE ' || cache_size ||
' ' || DECODE(order_flag,'N','NOORDER', 'ORDER') ||
' ' || DECODE(cycle_flag,'N','NOCYCLE', 'CYCLE') ||
';' || chr(10) || chr(10) || chr(10)
From dba_sequences
Where sequence_owner = '<my schema>'
spool off -
Unable to charge my Ipad 4 with my Laptop (HP 7010tx) USB . I am Getting error message as "Not Charging" . Please give a solution for this ...???
The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
Best Practices for iPad Battery Charging
http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
How to Save and Prolong the battery life of your new ipad
https://discussions.apple.com/thread/4480944?tstart=0
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
iPhone, iPod, Using the iPad Charger
http://support.apple.com/kb/HT4327
Install and use Battery Doctor HD
http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
To Extend a Device’s Battery Life, Get to Know It Better
http://tinyurl.com/b67c7xz
iPad Battery Replacement
http://www.apple.com/batteries/replacements.html
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
Cheers, Tom -
NO HDMI TO TV SOLUTION FOR CONEXANT HD AUDIO ON DV NOTEBOOKS
CHANGE DEFAULT IN SOUNDS AND HARDWARE TO SPDIF..THERE ARE TWO LISTED SPEAKERS IS THE CURRENT DEFAULT.....THIS IS A SOLUTION FOR WINDOWS SEVEN PRO CLEAN INSTALL...OR VISTA HOME PREMIUM......ON MY DV9200CTO NOTEBOOK....THANKS TO VERA FROM MANILLA...MS TECH SUPPORT...THIS WILL WORK ON ANY LAPTOP SHOWING ONLY TWO OPTIONS FOR OUTPUT OF SOUND.....THERE IS NO HDMI ICON...YOU WILL NOT FIND IT ON YOUR SETTINGS....SHARP AUDIO EXPERT VERIFIED THE SOFTWARE PROBLEM....SEE MY POST ON TECHNET...UNDER CATON HANDLE......WHOOOPEE SOUND IS BACK...
MODERATORS PLEASE POST AND ADVISE
CATONcaton,my problem sounds similar:
i have a hp pavilion dv6-1247cl laptop.running on windows 7
initially i was able to use the duplicate feature-fn/f4 key to display and hear my web page on the tv screen using the hdmi cable connection.
i am unsure if i have accidentally changed a setting recently on my laptop or what,but i am unable to get sound audio any longer through my tv or receiver system as before. the video from the laptop on the tv still shows fine
the hdmi connection ran computer to tv then audio cable out from tv to receiver.
i can get the sound to work if i connect an audio cable directly fron the hp headphone jack on my laptop into the same audio input channels in my receiver.
anyone got any ideas if the laptop is on the fritz or do i just need to change some setting
ps the laptop is relatively new
please advise of web site where i can seek a solution
thanks for any input you may have
owen -
Solutions for previewing HDV via video monitors ?
I have recently been given the task of setting up a video editing suite combining:
FCP6
HVR-1500 decks
Panasonic BT-LH1700WE LCD video monitors
FX7E HDV cameras
I've read that it is not possible to preview HDV via firewire and this seems to be the case thus rendering the Video preview monitors useless via the decks at least.
My question is what would we need to get in order to get a live broadcast preview to the monitors ?
Many thanks in advance.
-mattOk so i've done a little research and it seems like The Matrox MXO would be the best solution for our needs.
Does anybody have any experiance with this or a similar output device ? -
Best Solution for Creating an Onlne Purchase order form with multiple calculation fields
I am a bit confused. Our school has a Forms Central account which works great for our registration forms but I need to find a solution for creating an online purchase form with multiple calculation fields - I know that forms central does not support calculation fields (too bad) but I know that Acrobat Pro does... soooo...
Can you create the forms in Acrobat and then somehow integrate the advanced features into forms central? Do they talk to each other? Is this easy to do? .... I guess another way to putting it is can you create the forms in Acrobat including all of the advanced features for payment calculation and then host it online using Forms Central to manage and collect the data? (I guess that really is my question)
Thanks (how does this compare to a solution like Formstack?)Hi, thanks.
The naming convention was the consistant up until a point when I read that you need a '.' syntax (?!) - does anyone know if this is true?
Attached is a version with Bernd Alheit's suggestion and with all the naming of the fields being consistant. It's still not working for me though after doing this and I'm stuck as to why, because I think it should work. I've also tried writing the calcualting line of code in the same manner that Bernd Alheit suggests before I came on here, and it wouldn't work then.
As with any coding, it must be something to which I have done, but I can't see it anywhere
Any ideas? Thanks for helping me
Cheers -
Looking for 2 Product Solutions for eCommerce site created in Muse and published to BC
Seeking suggestions for 2 separate BC eCommerce website product applications: I have within BC so far about 200 image in the in a folder in the "File Manager" -AND- each image has been optimized as a low-res digital image down-load product (divided among 20 catalogs).
#1. Image downloads not for individual purchase but as (a bundle of 6 for one price) and (a bundle of 13 for second price) only.
I'm trying to customize two BC products a 6 Pack & 13 Pack of digital image downloads. Normally in BC, a visitor could purchase a single image as a downloadable product and after successful check-out they would receive an email containing the download links. I need to disable single unit purchases and enable the customer to ONLY select 6 images for one price -or- select 13 images for one price. After successful check-out they would receive links for either 6 download files or 13 based on their purchase. They could also purchase multiple pack sets.
#2. Allow the site visitor to select 12 images (from 200 images among 20 catalogs) for a 12 month custom calendar which would be printed and shipped. The BC product here would be a 12 month custom calendar. I have a product listed in BC as a "12-Month Custom Calender" and a display page titled the same. I have been looking into a drag n drop system that would allow the visitor to: purchase the product > select 12 images > submit their select by email to site admin.
I have limited coding skill and I should mention that I originally created and continue to add-on to the site with Adobe Muse. Because I chose to use Muse, I have been looking for solutions that I can embed in Muse pages as "Objects" as Muse will over-write BC custom elements as it is over-written. I have looked at either using a 12 field drag n drop which might work but I can't determine how to make the 20 catalogs available on the same page to select from.
Can ANYONE offer suggestions?
ThanksSorry but in no way will you get that to work using Muse.
You need to custom trigger the core functionality BC fires to add to cart in the system as well as update the visuals etc, and also overcome some of the BC scripting and what that does and function overrides etc. You need a high end front end developer at the least to be able to help you, and not using Muse.
Maybe you are looking for
-
Nice! Multilingual forms?
Nice work, guys. I've been evaluating this APTT for a couple of days and it's working pretty well. I'm just wondering about support for multi-lingual forms, including non-ASCII characters. There is a line in the System requirements, "While ATTP is o
-
I am thinking of upgrading. I am looking at refurbished laptops. I am trying to see what the differences are between the macbooks and ibooks. I currently am using a very outdated imac. I use the computer for e-mail...shopping..research on various
-
How can I get a 320kbps mp3 using "share to iTunes" without normalizing in Logic Pro X?
After importing and editing an mp3 file in Logic Pro X, I want to simply "share to iTunes" and get a 320kbps mp3 without normalization but I can't figure out how to do this without normalizing. With Garageband, it's simple; but with Logic Pro X, I c
-
Remote Function Module call from ECC to CRM (how to pass parameters?)
Hi there, I have a remote FM that I would like to call from ECC to CRM. The FM is remote-enabled, so I assume that I can call this from CRM. However, in CRM some of the table structures that is required are not available. Hence, my export/import para
-
My son received a new camera for Christmas. After successfully importing photos from his camera (an HP), I can no longer import photos from my camera (Cannon Powershot A85) that previously worked fine. When I click the import button it does not recog