Seen but not seen

Network available but can't be found in Assistant or Admin Utility.
My network went down and I had to reset the router at which point it came back up, however neither Assistant or Admin Utility can find it.
Currently the network is seen and operation on all the computers via Internet Connect.
I reinstalled Airport Extreme from the CD, version 4.2, however there has been no change. Software update indicates that I'm running the latest version.
I have a recent backup from Airport Admin which I can open but I can't do anything with it other than look at it, meaning that the import option is greyed out in the Airport Admin window.
Because the router can't be found even after rescanning I can punch "OTHER" and put in the working network's password and hence can access settings. I can do a minor change like select another channel and then hit "Update" which seems to do an update however the Base station is still not found in Admin. It is found in Airport Setup Assistant which says" The Airport Setup Assistant has found an Airport Base Station ( the current operating one) and asks me to proceed, I click continue and nothing happens.
I've repaired permissions with no result, I've verified Disk, again without showing errors or solving the problem.

Solved, but not in the way I would have hoped.
I run another computer out in the studio, essentially this is was a clone, though it has sort of gone off on it's own way, however it does have access to the Base Station.
From that machine my Base station was properly recognized and from there I updated the base station thru the Airport Setup Assistant. It is now recognized in both the Airport Utility and the Airport Setup Assistant.
So, it's fixed, but for the benefit of others who are not so fortunate to have a running clone hanging around I'd like to know what is going on.
I should add that I have a backup clone connected to the main machine. This should have had an full system from a couple of days ago. When I booted off that clone, before I solved the problem, the problem was still there. I'm trying to figure out what that means. I assume that perhaps it is a hardware problem with the internal airport card which would cause the clone to also lose the base station?

Similar Messages

The "join" button on both my iPad and iPhone is grayed out. Network can be seen but not joined

The "join" button on both my iPad and iPhone is grayed out. Network can be seen but not joined

I've reset the password a few times and know I am using the correct one. I get the same error on both my iPad and iPhone. Both see the network but maybe there is a problem with the router. I've also reset that a few times with no luck. Thank you.

When I make a video with the camera ipad mini seen but not heard I can do ?

when I make a video with the camera ipad mini seen but not heard I can do ?

Yeah, of course you can. All you do is, open PhotoBooth, record your video and then, once you have stopped the video recording just drag the movie out of the bottom of PhotoBooth onto the desktop. It is in .mov format so you can then add it to iMovie for further editing or just upload it to youTube as it is.
Easy as pie!

I have 2 external drives connected to my new iMac. I can see but no one else can, the other can be seen but not written to.

I have 2 problems, i have 2 external drives connected to my new iMac.
Both are formatted to FAT 32, one I can see but no one else can and I can write to that drive,. The other can be seen by all but not written to by me or anyone else (This drive was used on PC but is FAT32 (have been back to the PC & told it to read write).
Permissions are correct on both that I can see. Thats the extent of my knowlege.Please help

Whilst it may not be your fault I am afraid it appears that your post is on a forum which is not the best for your OS. It will save the time of the unpaid volunteers here, and may resolve your issue faster, if you could examine the list below and see if there is a more appropriate forum to which you could direct your question.
OS X 10.9 Mavericks
OS X 10.8 Mountain Lion
OS X 10.7 Lion
OS X 10.6 Snow Leopard
OS X 10.5 Leopard
OS X 10.4 Tiger
OS X 10.3 and earlier
OS 9, OS 8 & System 7
OS X Technologies
OS X Server
iPad
iPhone
iPod
Other

Text seen in swf file but not seen in flash pro. publish

I am using fmath formula component for flash. when i push ctrl+enter, texts in formula object are not seen, there is only tiny squareroot symbol. however, when i open created swf file, everything seems normal. I use flash player version 11.2. . Also, everything is ok in version 9.
http://www.fmath.info/flash/download.jsp

Are you setting the font that is being used to display the formula yourself? If so is it properly embedded and issued to the component properly? A quick way to check is to use a known system front (Arial, _sans, etc) and see if text shows up. If it does you're just not either embedding properly or aren't pointing to the font correctly in the component.

Audio Tracks can be Heard but not Seen

I am using Logic Studio 9 and in Logic Pro all the sudden I have had a problem with my audio tracks. When I record the tracks I can see the track audio waves being cut but once I hit stop the track visual go to a straight line with no feature. If I back up the play head and press play I can hear the audio of the track, but not see it. I can even bounce the track and use it in iTunes or WaveBurner, but still I cannot see the track visual info. This just recently started. ANY ANSWERS to this mystery would be greatly appreciated.
Thanks

http://discussions.apple.com/thread.jspa?threadID=2371889&tstart=0

Flash is installed ,but not seen by Chrome or Firefox

Here is what I checked in Chrome , I have:
Adobe Flash Player - Version: 15.0.0.189
Shockwave Flash 15.0 r0
This is installed but not being recognized by either firefox or chrome. I am on a WIN 8.1 pc and IE does not work so it is disabled/turned off. It does not even open anyway. How do I fix this?

Let me clarify, I need flash to work in Firefox and Chrome, IE is not important. I rarely use it

Epson 7400 being seen but not printing on Mac OS 10.6.7

My Mac-Mini (new yesterday) sees my Epson 7400, prints Emails fine, but when try to print anything else, it just pause and says Error: /system/library/printers/libraries/printjobmgr/contents/MACOS/printjobmgr failed

When you print job manager errors sometimes deleting the printer and then adding the printer again can fix this. If not then a reset of the printing system can resolve the error.
How to Reset the Printing System
1. Open System Preferences > Print & Fax
2. Move your mouse over the Printers list
3. Hold down the Control button and click the mouse
4. Click the "Reset printing system ..." popup
5. Restart your Mac
This will remove your printer but not your printer drivers, so you will only need to add your printer again.

Airport Express: Internet Access Works But Not "Seen" in Admin. Util. ??

Hi All --
I have a friend with the set-up described below and a seemingly impossible problem. he's asked for my help, and so I'm asking for yours, because frankly the situation just has me stumped. Here goes:
Set-Up & Other Relevant Facts
• DSL connection comes out of the phone jack and goes to a Westell model 6100 modem.
• From there, a short Ethernet cable goes to a Linksys 5-Port Workgroup Switch.
• Two Ethernet cables exit the Linksys Switch: one goes to a PC, and one goes to an Airport Express (AX).
• From the AX, a USB cable goes to a printer (a Brother 1440 laser printer).
• The AX is only about 10 feet from his PowerBook G4 15-inch and he gets a full (four-bar) signal on Airport menulet at the top of the screen.
• When he first set-up his system, the G4 and the Airport did set up the Brother printer (using the Airport Setup Assistant), and the Brother is listed as a printer on the G4's printer window or such.
• Both the G4 and the PC access the web fine via this setup (the G4 wirelessly). In System Preferences > Network, the Airport Network is listed, and it says "Airport is connected to the network Apple Network 6c6c1. You are connected to the Internet via Airport."
Problems
• When the Airport Admin Utility is opened, no Airport Express appears at all, even when "rescan" is repeatedly clicked.
How can this be? How can the PowerBook be connecting wirelessly to the Web through the Airport Express, but the Airport Express no be "seen" by the Airport Admin utility?
• In addition, although web surfing is possible for both PowerBook and PC, neither computer is able to successfully print to the Brother 1440. When he tried printing from the PC, he got the following error messages:
[Status for LPT1]
Result=(02)The printer on this port is not responding.
Status Line=BUSY:H,ACK:H,PE:H,SLCT:H,FALT:H,SLIN:L,HBSY:H,INIT:H,STB:H
Later, it seemed that printing from either computer would start and then stall, flashing a variety of different signals about spooling or "printer busy" and the like, all of which appeared to indicate things just weren't working right..
Anyway, the initial questions we're dealing with are the ones in bold above. The printer issues are probably are related and they can be addressed secondarily.
Any and all help with this will be greatly appreciated. Thanks everyone.
-- JDee

Thanks for your reply- just to re focus my problem- I
have no issue with getting a wireless network "green
light"
Which is the cable modem correctly giving the Express an IP from your ISP's DHCP pool of numbers.
- my issue is I can't stream itunes or get a
usb printer to work off the xpress USB port.
I have checked everything as my posts explain- The
reason I have been looking at this thread is I have
never been able to see the airport in a "scan" per
JDee post.
That is odd and doesn't happen on my wireless network!
Nor have I read in any post that an extra
ip address is necessary
All routers have at least two IP's - an external and an internal. When the router acts as an internal DHCP server it hands out many more IP's. Your Express gets one external IP and the default internal one is set to 10.0.1.1 and the first IP handed out is 10.0.1.2, etc.
However I have seen different subnets- from dncp
server.
Are you talking about the external IP's that your ISP is randomly assigning without your control? Are you talking about the different ways you can configure the internal DHCP numbers? If not there's something else going on. Everything on Douglas internal network should have an IP from the Express DHCP server vs. JDee's internal IP's should all be assigned by the modem/router DHCP server. Once you have everything on the same network numbers AirTunes, printers, and Airport Admin Utility lists just work!
Hey look I really appreciate your help here in
anyway- I'm really stumped. I want to stream music
really bad... and just don't see why it won't work-
its drving me crazy...
I enjoy a good challenge, especially when they are solvable. After trying all the possible software and connection possibilities there's always the chance it's been a hardware failure all along
What IP number does your computer have and what number does the Express have? If it's a router it has two IP's!

Seen but not heard?

Hi, I have an iMac G5 with an iSight camera, when I use iChat, I can see and be seen, I can hear the other party, but they can't hear me.
I have tried the settings with video turned off and just tried with audio only - same problem. I have checked my QT settings, and have streaming set to my bandwidth. I have checked my mic for both internal and iSight - both set to highest setting. I have tried it with using alternately the internal mic and the iSight mic - no luck. I have also had this problem with other chat programs in the past - and eventually gave up trying to make it work at all.
My internet connection is Satellite 2-way 512/128. I also occasionally get error "not enough bandwidth". I have tried deleting the iChat prefs as per previous discussions - no difference.
Please help as it really should work!

Hi Melclift,
This is almost certainly down to your satelite connection.
There maybe nothing you can do about this other than changing to Cable or DSL.
2:09 PM Wednesday; May 10, 2006

Ipod can be seen by Windows 7, but not seen by Itunes.

Hi - A friend has a Dell laptop running Windows 7. It was recently in the shop to remove a virus. Everything now works fine, except it won't work with any of her ipods. The ipods can be seen under Devices and Printers, and by the Device Manager. They aappear to be associated with the correct drivers. But if I select to view the properties using Device Manager, the spinning wheel cursor appears, and the Device Manager.stops responding. The laptop also will stall in the shutdown process, if the ipod is connected. Disconnecting the ipod at that point, causes the laptop to finish shutting down.
I should mention that an ipad works fine with Itunes on the laptop.
I have reinstalled the Itunes drivers and software several times. I've put the ipod into disk mode, also tried a different ipod cable, and neither helped. I've run virus scans using different anti-virus software, but they don't find anything wrong. I'm able to use the same ipods on a different Dell laptop that is also running Windows 7, so I don't think the ipods are a problem.
Nothing else on the laptop seems to be broken. Everything else works. Other USB devices work fine, so I don't think it's a USB issue.
The next step appears to be to reinstall the operating system. But I would like to know if there is anything else worth trying before doing that.
Thanks. - Mark

1. Update iTunes to the latest version. Plug in your iPod. If iTunes still can't recognize it, then in iTunes in the top left corner click help> run diagnostics. On the box that comes up, check the last two things. Click next and it should identify your iPod.
2. Click on your windows start menu. Type in "services". Click on it and when it pops up, on the bottom of it click on "standard". Now Scroll down to find "Apple Mobile Device" Right click it when you see it and click on "Start". When it has started, close iTunes and replug in your iPod and it should show up.
3. Check the USB cable
4 Verify that Apple Mobile Device Support is installed
5. Restart the Apple Mobile Device Service and verify that the Apple Mobile Device USB Driver is installed.
6. If you just want to add some photos, songs and movies from computer to your devices, you can use an iTunes alternative to do the job
7. Check for third-party software conflicts.
<Link Edited By Host>

Actionscript code can be seen in a search, but not seen in Actions Panel nor symbol

I purchased a template which has flash menu buttons. The current button url's go to index.html, index-2.html, index-3.html, and so on. I want to change these. In Flash, I searched for index-3.html and it finds it at the location: Symbol 'Button2 copy 3' -> Layer 'Layer 4' -> Frame '1' and the actionscript command is: getURL("index-3.html");
Everything is fine so far. However, when I double-click the symbol and go to the location (or double-click the search result), the actionscript command cannot be found at all. I tried pressing F9 to open the Actions Panel, and I see the button symbol but I don't see any actionscript commands associated with it. It seems to be very unusual - the search picks up the actionscript command but it can't be seen in the symbol's location where it says it is nor can it be seen in the Actions Panel. The script does work but it just cannot be seen! Does anyone know how to see the actionscript code in the Actions Panel or in the button symbol?

show a screenshot of movie explorer after searching for getURL("index-3.html")

Ipod recognized by windows but not seen in explorer or itunes. only charges

I recently had to reimage my hard drive. Once I got everything back to the way it was, I reinstalled iTunes and the iPod software. However, whenever I try to connect my iPod mini to my computer, Windows will recognize it as a new device and get a "Found New Hardware: iPod mini" bubble. Eventually a "Found New Hardware wizard" window pops up and asks me to install the driver. As I've already installed the iPod software I tell it no and the another bubble pops up telling me that there was an error during the install of the driver. All my iPod will do is charge. I've tried the 5 r's, I've tried everything I could find in the support site that sounded even remotely like what I was experiencing. I've gone through the device manager, but my iPod doesn't show up there at all. I don't get the spinning arrow-circle on my iPod. I have absolutely no clue as to what's wrong with it. Any one have any ideas?

Hello There
Sorry I don't have the answer to your question but I am having excatly the same problems as you have got, also can't find a solution to this either, my ipod has been wiped and have nothing on it at all now and can't get anything from itunes on it. Hope this makes you feel a bit better knowing your not the only one having these problems, if you manage to sort it, please could you let me knwow and vise versa. Many thanks. Jane

IPod recognized as disk drive by WinXP but not seen in iTunes or iUpdater

HELP!!
A few short weeks ago I was ecstatic when I received my new iPod video as a Christmas gift. Imagine my dismay as I have been trying to get the darn thing to connect to iTunes ever since!
I have gone through the Apple website troubleshooting, have spent HOURS with a MAC "genius" and we still can't figure out what's going on.
The device has been restored and iTunes/Updater have been removed and re-installed NUMEROUS times but still can't get my 30G iPod Video to register in iTunes. Apple swears it is my laptop. I've removed everything and re-installed from scratch so I find it hard to believe that it is just my PC.
When I plug it into my USB I get the "Do Not Disconnect" icon that just keeps flashing (guess I should be happy its not freezing anymore!). I can see it as my "E" (Removable Disk) Drive but can't find it with iTunes or iPod Updater (Oct05 and Nov05 versions). It does appear when connected to an Apple store MAC or the Apple store's PC...so maybe it is mine.....?
Any advice?
Thanks!
Toshiba Laptop - P4 Windows XP

Maybe you solved this or not but I have a suggestion. If you have a PCMCIA slot try adding a usb 2.0 pcmcia card. I was having a world of troubles that have included one already returned 5G 60GB. It was rendered inoperative by a failed restore process. I assumed it was a defective ipod.
Receiving the new one last night it was showing similar behavior to the one I had to replace. I thought my laptop might be a factor. I was already using a compUSA usb 2/FW card with the ipod but after searching I found a post that warned that card is trouble. I just bought a HP USB 2 pcmcia card (US$39) and about 8 gigs of movies was just gulped down by my ipod in one sitting. With the compUSA card it would cough and choke on one movie sometimes.
Sorry for your troubles. Good luck.
dell inspiron lappy Windows XP Pro HP pcmcia USB 2.0 adapter

File picked up by sender channel but not seen in CC monitoring nor in moni

Dear All,
It is a file to JDBC scenario where the sender communication channel picks up a file and sends it to several receivers interfaces ( 1 jdbc receiver channel). The file gets picked up by sender communication channel, but problem is that it does not get traced in communication channel monitoring, not even in message monitoring in RWB and SXMB_MONI. Thus no file processing. Sometimes this does not happen and the file gets traced in either of the monitoring tools. Please help as to why would this happen.
The scenario works correctly at times. its configured correctly. Please guide.
Thanks & Regards,
Priyanka Salvi

Hi,
Thanks. No, archiving faulty source files functionaly was not used earlied.
I enabled it by giving a path in the FTP server itself, but no files were placed there in the same case.
Please give me some examples of OS commands.
The file is picked up but it seems it is unable to read/forward for further processing.
This is because after the file is picked up, no messages are found with the outbound interface as well in message monitoring.
I am manually placing the file at the required path and the procsessing mode in CC is delete.
The receiver determination and all other configurations are correct.
I had tried by creating a new sender CC and deactiving the earlied one. Using this files were picked up and processed for few days and now again the same problem.

Seen but not seen

Similar Messages

Maybe you are looking for