SEFOS configuration to connect a 24 port NEM to a Cisco Router

Hi - In need some configuration advice realting the Swtich ethethern 24 port Nem card for a B6000.
The Uplink ports are not connecting.
See Below.
Ex0/1 up, line protocol is down (not connect)
Bridge Port Type: Customer Bridge Port
Hardware Address is 00:21:28:f2:85:55
MTU 9216 bytes, Full duplex, 10 Gbps, No-Negotiation
HOL Block Prevention enabled.
Input flow-control is off,output flow-control is off
The port config is :-
interface extreme-internet 0/1
no shutdown
no negotaiation
speed 1000
dot1x port-control auto
spanning-tree portfast
swtichport mode trunk

Was this resolved? If so what was the resolution? Thanks in advance.
Sean.

Similar Messages

Can I run a cat5 cable to a 4 port hub from a cisco router then connect one of the hub's output ports to an airport express to 'extend' my wireless range?

Can I run a cat5 cable to a 4 port hub from a cisco router then connect one of the hub's output ports to an airport express to 'extend' my wireless range?
Flow would be
Cable modem---->cisco e2000 wifi router (This is broadcasting wifi but not strong enough)---->4 port hub ---->airport express (to extend the wifi in another part of house)
thanks!

Yes, you can do this as you stated. In essence you will want to configure both routers for roaming network. Please check out the following Apple Support article that describes this type of network. Although this article uses two or more AirPorts, it can be done with just about any manufacturer's router.

Connect two internet lines on the same cisco router 3945 series

i have two internet lines from the same provider and i have one router i want to connect the two lines in the same router
any ideas !!!!!!!!!!!!!

Hi,
No problem, similar treatment. Follow
1. Create IP SLA/Track for both internet link
2. Break your LAN subnet into 2 smaller subnet
3. Create route map, Match with 1 subnet & route the traffic towards 1st internet link
route-map General_Internet_Traffic permit 10
match ip address 115
set ip next-hop verify-availability 10.1.1.1 track 1
set ip next-hop verify-availability 11.1.1.1 track 2
4. Create route map, Match with 2 subnet & route the traffic towards 2nd internet link
5. Configure NATing/PATing over the interface, selecting by route-map
ip nat inside source route-map General_Internet_Traffic interface FastEthernet0/0 overload
- Ashok

How to configure Null Modem on serial port?

Previously, I use a windows XP to accept incoming connection by Network Connections > Create a New Connection > Accept Incoming Connection
I would like to deploy an Cisco router to replace this XP, how can i configure it? I convert the RS232 to smart serial cable, here is my configuration, fa0/0 connected to office LAN and S0/0 connected to null modem devices
The connection is up, however, the S0/0 is flapping up and down, and return packet is dropped by the router with msg encryption error
interface Serial0/0
physical-layer async
ip address 10.0.0.1 255.255.255.0
ip nat outside
encapsulation ppp
dialer in-band
async mode interactive
peer default ip address 10.0.0.2
interface FastEthernet0/0
ip address 172.16.1.31 255.255.0.0
ip nat inside
duplex auto
speed auto
dial-peer cor custom
line con 0
line 1
modem InOut
transport input all
autoselect during-login
autoselect ppp
stopbits 1

Thank you Ravens Fan
I used your idea on the receive part and it worked fine but it has two problems:
1) when I use the waveform graph it keeps increasing the X scale infinitely.
2) when using the waveform chart and set the chart history to 100 it work fine at first but it goes out of shape after a while.
I think that's all due to the n dimention array is there a way to make a 100 dimention array in a way that new elements erase old ones.
Another thing I
wanted to be sure I understand it right, on the sending loop I should set the “digital
waveform to binary” to U16 so that at the receiving part the chart (or graph)
will read it as U32 ,but shouldn’t the receiving signal be different than the
sent signal; since different points.
I attached the new VI.
Thank you
Attachments:
sine on serial 16 bit test.vi ‏105 KB

Advice about FXS Port configuration for connecting to modems

Hello all,
We have not confirm the problem, but we are having reports that analog devices like USR V.92 Modems and Power meters are not connecting or dropping the connection. We have an ISR 2911 with the 4-port FXS-DID WIC (VIC3-4FXS/DID), configure to an internet SIP truck provider. The Router is running IOS 15.3(3)M2. If we connect an analog phone to the FXS port and call, voice is clear. So the question is what configuration settings should we have for FXS ports and/or dialpeers for connections to modems? Attached is the current configuration of the router.
Do we have to be worried about Codec? If so which Codec should we configure?
Any Physical FXS settings should be set?
Are my DSP setup correctly?
Again, I'm at a loss, as voice sounds good and my searches for modem connections to FXS Ports on CUCME is coming up dry. Any help would be great.
As far as the "Power Meters", we are talking substation power meters.
Thanks for any advice you can spare and your time,
Nick

Hi Amit,
No problem on the delay. Your help is very much appreciated.
You're losing me a bit. Because I don't know if your giving me dial-peer 1 as an example. 1 being just a random number. Or your telling me to change my current dial-peer 1 configuration. Which is currently a pots dial-peer:
dial-peer voice 1 pots
description POTS port 0/1/0
destination-pattern 111111111
port 0/1/0
dial-peer 1000 voip is our outbound call leg. Sorry call legs are not exactly clear to me yet. In fact they haven't been in years. :) So change my dial-peer to dial-peer voice 1 voip?
My other question still unknown to me is should we use:
fax protocol pass-through g711ulaw
Even though we are trying to use a modem and not a fax? Also this command is a dial-peer command and not a global command. So what global command should i be using?
Again thank you for your time and help,
Nick

Solaris 10connectivity to EMC: failed to configure ANY device on FCA port

I'm connecting a E2900 server with a EMC symmetrix storage with fiber channel.
But I'm getting the following errors, and I'm not able to see the external disks. Any help is really appreciated.
bash-3.00# cfgadm -al
c3 fc-fabric connected unconfigured unknown
c3::5006048c52a5b746 unavailable connected unconfigured failed
c4 fc-fabric connected unconfigured unknown
c4::5006048c52a5b749 unavailable connected unconfigured failed
bash-3.00# cfgadm -c configure c3
cfgadm: Library error: report LUNs failed: 5006048c52a5b746
failed to configure ANY device on FCA port
bash-3.00# tail -f /var/adm/messages
Nov 27 16:42:12 cosemm1 scsi: [ID 243001 kern.warning] WARNING: /pseudo/fcp@0 (fcp0):
Nov 27 16:42:12 cosemm1 Unsupported LUN Addressing method 40 in response to REPORT_LUN
bash-3.00#
SO is Solaris 10 and I have installed recommended pathes:
118833-36 SunOS 5.10: Kernel patch
125100-10 SunOS 5.10: Kernel patch
120011-14 SunOS 5.10: Kernel patch
127111-01 SunOS 5.10: Kernel patch
119130-33 SunOS 5.10: Sun Fibre Channel Device Drivers (only necessary for Leadville Stack driver)
125184-04 SunOS 5.10: Sun Fibre Channel Device Drivers.
120222-21 SunOS 5.10: Emulex-Sun LightPulse fibre channel adapter driver v2.20k (only required for Emulex HBAs running Leadville)
125166-06 SunOS 5.10: Qlogic ISP fibre channel device driver v2.22 (only required for Qlogic HBAs running Leadville)
122640-05 SunOS 5.10: zfs genesis patch (require for zfs)
120473-12 SunOS 5.10: lib nss ldap PAM zfs patch (require for zfs)
119090-24 SunOS 5.10: iSCSI device driver and utilities
Also I have modified /etc/system adding those lines:
set ssd:ssd_max_throttle=20
forceload: drv/ssd
bash-3.00# modinfo |grep qlc
66 7ba7e000 ce1f8 282 1 qlc (SunFC Qlogic FCA v20070717-2.22)
bash-3.00# luxadm -e port
/devices/ssm@0,0/pci@18,600000/SUNW,qlc@1/fp@0,0:devctl CONNECTED
/devices/ssm@0,0/pci@19,600000/SUNW,qlc@2/fp@0,0:devctl CONNECTED
bash-3.00# luxadm qlgc
Found Path to 2 FC100/P, ISP2200, ISP23xx Devices
Opening Device: /devices/ssm@0,0/pci@19,600000/SUNW,qlc@2/fp@0,0:devctl
Detected FCode Version: QLA2460 Host Adapter FCode(SPARC): 1.26 05/17/07
Opening Device: /devices/ssm@0,0/pci@18,600000/SUNW,qlc@1/fp@0,0:devctl
Detected FCode Version: QLA2460 Host Adapter FCode(SPARC): 1.26 05/17/07
Complete
bash-3.00# luxadm -e port
/devices/ssm@0,0/pci@18,600000/SUNW,qlc@1/fp@0,0:devctl CONNECTED
/devices/ssm@0,0/pci@19,600000/SUNW,qlc@2/fp@0,0:devctl CONNECTED
bash-3.00# luxadm -e dump_map /devices/ssm@0,0/pci@18,600000/SUNW,qlc@1/fp@0,0:
devctl
Pos Port_ID Hard_Addr Port WWN Node WWN Type
0 610f13 0 5006048c52a5b746 5006048c52a5b746 0x0 (Disk device)
1 617613 0 2100001b320122b7 2000001b320122b7 0x1f (Unknown Type,Host Bus Adapter)
bash-3.00# luxadm -e dump_map /devices/ssm@0,0/pci@19,600000/SUNW,qlc@2/fp@0,0:
devctl
Pos Port_ID Hard_Addr Port WWN Node WWN Type
0 620f13 0 5006048c52a5b749 5006048c52a5b749 0x0 (Disk device)
1 627613 0 2100001b32014eb8 2000001b32014eb8 0x1f (Unknown Type,Host Bus Adapter)

Check the configuration on the EMC side. This error message is the heart of the problem:
"Unsupported LUN Addressing method 40 in response to REPORT_LUN"
A quick Googling leads me to believe this means you're trying to assign a LUN ID higher than 255 to the host.
Best of luck!

Failed while creating virtual Ethernet switch. Failed to connect Ethernet switch port

Hello Folks
I am completely stuck with the configuration of my virtual networks. I have one logical switch left to add to one of my Hyper-V 2012 R2 hosts when I started getting the error below when I try to add logical switches to either Hyper-V Host. I have been using
the document. 'Hybrid Cloud with NVGRE (Cloud OS)' to implement the virtual networking. Basically using the exact configuration that is in the document. I have added the PA Logical Network and the Network adapters and added the logical switch for it to my
hyper-v 2012 R2 host and everything was fine. I am now trying to add my ISCSI Logical Switch to the host and this is the error I get. My other Hyper-V host I get this error for any logical switch I am trying to add. Can someone help me with this error. I haven't
been able to find any information about it.
Also a some quick info on tracing an error like this so I can figure out what is causing it.
Thsi is my configuration so far
So as far as I know everything is peachy untill the error below. Dead stop now
Error (12700)
VMM cannot complete the host operation on the 08-NY-VHOST01.accounts.ccac-ont.ca server because of the error: Failed while creating virtual Ethernet switch.
Failed to connect Ethernet switch port (switch name = '******', port name = '88C16766-ED02-4AC0-8CD7-660AC9D424DD', adapter GUID = '{FAF431D8-0124-4E40-BB3B-9234BAA02973}'): The system cannot find the file specified. (0x80070002).
Unknown error (0x800b)
Thank you for your time
Christopher
Christopher Scannell

notice your GUID? you may want to consider ensuring that is the same GUID associated in your database. Sometimes during data corruption theres a smidge of a chance your sql database kind of either pulls old guids esp if this was reverted to snapshot
without it being powered off etc.
I would try that first. then i would consider if you get to configure that with your current liscense associated with the host. I would need way more info to help any further

You may need to configure the connection settings in the deployment descrip

Hi All
I am new to BPEL and going through Order Booking Tutorial (using 10.1.3.4 version of opmn ) .
I have a problem in 'Designing the Database Adapter to Insert Data' Chapter.
I have installed Oracle 10g Express Edition and BPEL Process Manager on my local system.
In the Example it has been asked to create a daabase connection with Third Party JDBC Driver. Instead I have created a database connection with Oracle(JDBC) Driver.So i didnt have to register any third party driver.
I cud access the Order/OrderItems table as well .
I Deployed the same on the server.But while running the process I get following error--
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
nested exception is:
     ORABPEL-11622
Could not create/access the TopLink Session.
This session is used to connect to the datastore. [Caused by: Listener refused the connection with the following error:
ORA-12519, TNS:no appropriate service handler found
The Connection descriptor used by the client was:
localhost:1521:XE
See root exception for the specific exception. You may need to configure the connection settings in the deployment descriptor (i.e. $J2EE_HOME/application-deployments/default/DbAdapter/oc4j-ra.xml) and restart the server. Caused by Exception [TOPLINK-4002] (Oracle TopLink - 10g Release 3 (10.1.3.4.0) (Build 080602)): oracle.toplink.exceptions.DatabaseException
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
I have checked several post on this error but every post talks about third party database.I have used Oracle Database only so why/What shud I change anything in oc4j-ra.xml?? This is my doubt .
Pls help me on this .Also Let me knowe in my case is there any need to create the datasource.?I am low at concept of database.
Pls help
Regards
Naveen

Hi
I am trying to insert orader and order Items as given in the Order booking tutorial..
Here are the files description
.wsdl file looks like
<service name="DBInsert">
<port name="DBInsert_pt" binding="tns:DBInsert_binding">
<jca:address location="eis/DB/MyConnection"
UIConnectionName="MyConnection"
ManagedConnectionFactory="oracle.tip.adapter.db.DBManagedConnectionFactory"
mcf.DriverClassName="oracle.jdbc.OracleDriver"
mcf.PlatformClassName="oracle.toplink.platform.database.oracle.OraclePlatform"
mcf.ConnectionString="jdbc:oracle:thin:@localhost:1521:XE"
mcf.UserName="system"
mcf.Password="6672B62098892995C8B651EFDF798A59"
/>
</port>
</service>
data source file looks like
<connection-pool name="MyConnection">

<connection-factory factory-class="oracle.jdbc.OracleDriver" user="orabpel" password="->pwForOrabpel" url="jdbc:oracle:thin:@(DESCRIPTION=(ADDRESS_LIST=(LOAD_BALANCE=on)(ADDRESS=(PROTOCOL=tcp)(HOST=nakhanna)(PORT=1521)))(CONNECT_DATA=(SERVICE_NAME=XE)))"/>
</connection-pool>
<managed-data-source name="MyConnection" connection-pool-name="MyConnection" jndi-name="jdbc/MyConnectionDS"/>
</data-sources>
oc4j-ra.xml looks like
<connector-factory location="eis/DB/MyConnection" connector-name="Database Adapter">
          <config-property name="xADataSourceName" value="jdbc/MyConnectionDS"/>
          <config-property name="dataSourceName" value=""/>
          <config-property name="platformClassName" value="oracle.toplink.platform.database.Oracle9Platform"/>
          <config-property name="usesNativeSequencing" value="true"/>
          <config-property name="sequencePreallocationSize" value="50"/>
          <config-property name="defaultNChar" value="false"/>
          <config-property name="usesBatchWriting" value="true"/>
          <connection-pooling use="none">
          </connection-pooling>
          <security-config use="none">
          </security-config>
     </connector-factory>
##################################################################3
Still I get the same error .
<bindingFault xmlns="http://schemas.oracle.com/bpel/extension"><part name="code"><code>null</code>
</part><part name="summary"><summary>file:/C:/product/10.1.3.1/OracleAS_1/bpel/domains/default/tmp/.bpel_FulfillOrder_4.0_e77c64251e45eb4711a3a093f92e6a86.tmp/DBInsert.wsdl [ DBInsert_ptt::merge(OrdersCollection) ] - WSIF JCA Execute of operation 'merge' failed due to: java.util.MissingResourceException
java.util.MissingResourceException
; nested exception is:
     ORABPEL-00001
java.util.MissingResourceException
java.util.MissingResourceException
java.util.MissingResourceException
</summary>
</part><part name="detail"><detail>null</detail>
</part></bindingFault>
Pls let me know if something looks wrong in the above files
Thanks
naveen

Is there way to share Air-Port Wi-Fi connection through ethernet port?

I was wondering if anyone could help me out with this, I have wireless network in the building, and is there way to configure Mac Mini to share Air-Port Wi-Fi connection through ethernet port (feed Vonage adapter)?

Have you actually shared wi-fi to ethernet on a Mac? I ask because it is not usually that simple, it is a more complicated configuration. Most folks who do it the way you described get a self assigned IP and nothing connects.
See my comment here;
http://discussions.apple.com/thread.jspa?messageID=12585788&#12585788
I have a Vonage phone adapter and Vonage does not provide the info that you need to hand configure these boxes, I have tried in the past with the one I have with a US phone number from here in Mexico.
Dah•veed

Configure Target - connection failed

Hello,
I have installed 11g Enterprise Manager Grid Control and deployed an agent using the silent install option on a second machine. Once the agent installation completed, it's Oracle 11g Database instances got picked up by EM. The problem is that when I attempt to configure the recognized instance I get the following:
"Error occurred while getting information for the specified target. Possible reasons include: the target doesn't exist; connection to the target failed."
looking at the emoms.trc:
2010-12-10 13:52:53,804 [EMUI_13_52_11_/console/database/instance/sitemap] WARN perf.sgatarget _getTargetVersionCategory.268 - Failed to get target versionjava.net.ConnectException: Connection timed out: connect
2010-12-10 13:53:27,002 [EMUI_13_53_05_/console/database/config] ERROR perf.sitemap initialize.291 - CommException: error while getting target info from the repository
2010-12-10 13:53:27,002 [EMUI_13_53_05_/console/database/config] ERROR perf.sitemap initialize.292 - oracle.sysman.emSDK.emd.comm.CommException: java.net.ConnectException: Connection timed out: connect
oracle.sysman.emSDK.emd.comm.CommException: java.net.ConnectException: Connection timed out: connect
2010-12-10 13:53:27,002 [EMUI_13_53_05_/console/database/config] ERROR perf.sitemap logStackTrace.2426 - oracle.sysman.emSDK.emd.comm.CommException: java.net.ConnectException: Connection timed out: connectNow I've had problems with closed ports in this environment before, is it possible that there needs to be another port open for this configuration? If so, which ports do I need to watch out for (considering the default values)?
Thanks.

When checking the agent status you will see what ports are used for communication between the Agent
Check the output of AGENT_HOME/bin/emctl status agent
Regards
Rob
http://oemgc.wordpress.com

How to configure BT connection from PDA?

Hello :)
PDA cannot find the ActiveSync service, though Windows Mobile Device Center 6.1 is running, and COM port is configured appropriately.
PDA HTC P3300 Artemis-WinMob 5.0, USB Bluettoth adapter, last version 7.10.10
in IVT BlueSoleil works fine
Manual *"How to configure a connection from the PDA (Windows Mobile 6) to the Windows Mobile Device Center"* not help
Windows 7 64bit

My HTC Windows Mobile 6.1 phone (not your model) in combination with Windows7 x64 and Windows Mobile Device Center works just fine for me with Bluetooth stack v7.10.10 (T). Ensure that you use the suitable x64 bit version of the Windows Mobile Device Center.
Here are my links:
http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
http://www.microsoft.com/downloads/details.aspx?FamilyId=4F68EB56-7825-43B2-AC89-2030ED98ED95&displaylang=en

I need help configuring a connection with asdm 5.2 for asa

Hi All
I am very much a novice with asdm 5.2 for asa and I urgently need to configure a connection but don’t know how to. I have 2 domains at work and someone is trying to connect their sql client from their pc in one domain to the sql server in the other domain (DMZ).
When he tries to connect he gets the error
Cant connect to MySql Server at "IP Address" (10060)
He is trying to connect on port 3306. Could anyone please give me any tips on how i can resolve this quickly? I know i am
trying a shortcut on this one but I recently started a new job and thrown in the deep end here and need to learn this asdm 5.2 for asa product from scratch with nothing more than the manual that come with the cd . My Cisco knowledge is from 2001 when i did half of a ccna course.
Any help would be greatly appreciated

Hi,
I'm not a security specialist but here is how I had it set up at home:
Essentially a NAT and a rule forwarding the port are needed. In this particular case I had an Oracle server running and a person requested remote access. So, for example, the source address was his external IP and the destination was the Oracle's external IP. For the NAT the source was the internal IP of the Oracle server and the interface was Outside.
Hope this points you in the right direction.

Need to configure Airport connection to access corporate wireless network

Need to configure Airport connection to access corporate wireless network.
Have imported my certificate from Windows XP machine into keychain and made Leopard always trust in order to authenticate automatically into my corporate wireless network. Also attempted to establish a new 802.1x connection via network preferences without any success. It keeps asking me for username and password even though we used self-generated certificates to log into corporate wireless network. Does anybody have any instructions on how to successfully configure certificates in Leopard?

Welcome to the discussion area, jackregan!
You'll need to "hard reset" the Time Capsule and then reconfigure it again. To do this, you will hold in the reset button until you see the amber light begin to blink more quickly, keep holding another second or two and then release.
The "hard reset" will not affect the data on your Time Capsule
Now you can open AirPort Utility and configure the Time Capsule using wireless (be sure to log on to the default network which will have a name like Apple Network xxxxxx), or you can connect an ethernet cable from your computer to one of the LAN <-> ports on the Time Capsule to have AirPort Utility communicate with it that way.
When you open AirPort Utility, click Continue to follow the guided setup to re-configure your Time Capsule. You would choose the option to "Create a wireless network" when you are given the configuration options.

Recently bought airport Extreme and have connected the device to the modem. WIFI works. However when I connect the LAN port to a switch I do not see the LAN printer and my NAS. Which setting do I miss?

I have installed my Airport Extreme and have conencted it directly to a modem. WIFI works fine. However I do not see my LAN network (printer. NAS,..).
Analysis:
Scen#1: When I connect the LAN port of the Airport Extreme to a switch (as input) and connect the other LAN devices also to the switch, those LAN devices do not have access to the internet. Also connecting the iPAD with WIFI to the Airport Extreme I cannot find my LAN printer and other devices.
Scen#2: When I connect the LAN port of the Airport Extreme to a router X (as input) and connect the router X to the same switch, and the LAN devices to the switch, those LAN devices do have access to the internet. Also connecting the iPAD with WIFI to the router X I can find my LAN printer and other devices in the LAN network.
Question what has impacted the behaviour of the Airport Extreme, not to detect the devices in the LAN network. Why is the use of a switch directly behind the Airport Extreme not working (no internet access for the other devices and Airport Extreme is not the basis station for the LAN network)?

Your scenario #1 is a correct configuration and should work. It seems as though your Extreme is not acting as a router as I believe you intend.
Most likely, you need to reset your modem. Power it down and let it rest for a few moments. Some need longer than others. Then, I recommend you "hard reset" your Extreme (see below) and configure it again, after the modem has been reset. From then on do not change what is connected to your modem without powering it down first.
Once configured, confirm your Extreme's wireless network works as expected and that your iPad and every other wireless device can load web pages. Then, connect the printer directly to one of the Extreme's LAN ports and confirm that it works as well. After that it should work equally well with a switch between it and the Extreme, as should every other wired device connected to the switch. This assumes your switch is an unmanaged device requiring no specific configuration.
Scenario #2: Having a router connected downstream of another is not a normal configuration, so don't pursue that as a solution. It will only distract you from determining the problem. If you want to repurpose Router X as another device do so only after everything else is working to your satisfaction.
To "hard reset" an AirPort Base Station: make sure it's powered up, then press and hold its tiny reset button and keep it depressed for five to ten seconds, long enough for its LED to flash amber rapidly. Release the reset button. Then, the LED will glow amber steadily for about a minute. Then, it will flash amber, slowly, about once every second or two, waiting for you to configure it with AirPort Utility.

I have Verizon FIOS and I am trying to connect an Air Port Express to my Directv

I have Verizon FIOS and I am trying to connect my Air Port Express to my DirecTV. My iMac does not see the airport express, even though the light is a solid green and connected to my HD-DVR. Any ideas?

Assuming your modem is wireless use Airport Utility to configure the AEX to extend an existing network. The modem's wireless router should be configured to allow its network to be extended.

SEFOS configuration to connect a 24 port NEM to a Cisco Router

Similar Messages

Maybe you are looking for