Segregating Network using WRT54GS

I have a client who runs a business out of his home, lets call it oilismoney. He has a dc running 2003 with 3 workstations. He also has 2 other machines which are not a part of the domain which need to access the internet.
The equipment we have as of now is a powerconnect 2708 switch, wrt54gs, and an older linksys befxxx wired router. He is connecting to the internet via a motorola surfboard modem.
Can someone please help me figure out how to get two separate networks going that use the same internet connection, but cannot talk to each other.

Connect the modem to a router1 (internet port) in gateway mode. (If your modem has also a router function you may use the modem as router1).
Connect router2 (internet port) in gateway mode to router1 (LAN port).
Connect router3 (internet port) in gateway mode to router1 (LAN port).
Assign LAN IP address 192.168.1.1/255.255.255.0 to router1.
Set internet connection settings on router1 as required by ISP.
Assign LAN IP address 192.168.2.1/255.255.255.0 to router2.
Set internet connection settings on router2 to DHCP.
Assign LAN IP address 192.168.3.1/255.255.255.0 to router3.
Set internet connection settings on router3 to DHCP.
Now anything behind router2 and router3 is protected as if they were directly connected to the internet. Computers connected to router2 or router3 cannot talk to computers behind the other router.
If you need shared computers (e.g. a printer for both networks), connect it directly to router1. You have to configure the printer with IP address as workgroup browsing will not work through a gateway.

Similar Messages

Unable to establish Network using WRT54GS V 6.0

I have had problems with this router since yesterday. I downloaded the new firmware V1.52.2 and that's when my problems started. I was losing my internet connection intermittantly. I plugged everything directly into my cable modem and I didn't lose my connection for an hour. I plugged everything back into the router and within 1-2 minutes I'd lose my connection. I'd get it back up in about 10 seconds, but as you can imagine it's a nightmare to do any downloads, play games, etc. I've had this router going on 8 months now, and it's worked like a charm up till yesterday. The reason I upgraded my firmware yesterday was so I could put my PS3 on the network and be "up to date" with everything. Anyways, so after all this frustration I decided I'd start all over with the router. I hit the reset button for 30 seconds. Now, the WLAN light doesn't come on, and the Power light blinks rapidly. When I run the Linksys EasyLink Advisor to set things back up, it says I'm not connected to the router. I've double and triple checked the connections. I hear the snap, and it works when I plugged directly into the cable modem. I think it has something to do with the WLAN light not being lit or the Power light flashing rapidly. Any ideas what it could be?

It seems that router is not working properly after upgrade & even the power light is flashing ....
Power down the router for atleast 1- 2 minutes .... power up the router & see if power light is solid or not...
If so check the Ip address under Local area network & try to open the set up page once again ....
After opening the set up page .... look for firmware upgrade if it is properly upgraded or not...

Can I create a unique subnetwork when extending a wireless network using Airport Extreme?

My office building has an Airport Extreme to provide wifi to our individual suites. I would like to create a sub-network using my Airport Extreme for my suite only that uses the wifi signal from our office building and provides internet to the computers (both wired and wireless) in my suite but have it protected so that other suites in my building can't see my computers. Is this possible and how do I do it? I have currently set up my Airport Extreme in wifi-mode "extending a previous wireless network" and have the router with its unique router name. But once I extended the wireless network, I could not find the network name of my router, only the office name (the one I was extending). The computers connected via ethernet to my Airport have internet access but none of my wireless computers see my airport name, it sees the office building network name. I'm assuming they are connecting to my Airport since the signal level is much higher than before and it appears that my Airport is rebroadcasting the network name of my office building. Is there a way to have my Airport broadcast its unique identifier for wifi, still connect to the internet via wifi signal to the Office building airport and maintain segregation between my computers and the rest of my office building?
Also, when I use the Airport Utility on my Iphone, I see the internet -> the office airport extreme -> and then 2 different base stations connected in a Y. Mine and my neighbors (who is probably doing the same thing as I am). But there is a dotted line to my base station, does that mean I'm connected to the internet via my neighbor's airport?
Any thoughts?

I would like to create a sub-network using my Airport Extreme for my suite only that uses the wifi signal from our office building and provides internet to the computers (both wired and wireless) in my suite but have it protected so that other suites in my building can't see my computers.
It is not possible to configure a single Apple AirPort router in this manner using wireless only, but it would be possible to do this with a single AirPort if you connect your AirPort Extreme to the "main" router using a wired Ethernet connection.
As for wireless only....you could probably do what you want by using two Apple routers....an AirPort Express to join the wireless network and provide an Ethernet signal to the AirPort Extreme's WAN port. Then the AirPort Extreme could then be configured to provide a separate network using a different subnet.
Users on the "main" network would not be able to "see" any devices on your "private" network and vice versa.
I use the two router set up all the time at hotels that only provide a wireless signal. The first Express "joins" the wireless network and feeds an Ethernet signal to the second AirPort which is configured to "create a wireless network" in router mode.
This way, I can connect multiple devices to my "private" network, but only pay the hotel for one connection since the hotel router only "sees" the AirPort Express that joins the network.

I have been using WRT54G wireless broadband router and WU...

I have been using WRT54G wireless broadband router and WUSB54G on my home PC for the last 2 years. It was working fine until recently I encountered serious connection problem.
The WUSB54G cannot connect with WRT54G.
Error message " Cannot assocaite with the access point.
I have checked the followings to try and solve the problem.
1) Refresh site survey the WUSB54G does not show my SSID, but it can show my neighbour'sSSID.
3) When I use my notebook with built-in wireless network adaptor to access wirelss broadband there is no problem at all. I can access my SSID.
4) I have try reseting the WRT54G and changing password but still can not solve the problem.
5) Uninstall and re-install
5) I have installed a new USB adapter (WUSB54GG) thinking that it could be the old WUSB54G is faulty. But still encounter same problem.
I am using Window XP Professional. What could be the problem?
Please provide your professional advice. Thank you.

Hi, Try to update firmware of router. You can get latest version from www.linksys.com/download, Hope it will help you

Howto use WRT54G router to make satellite receiver LAN terminal wirelessly connectected?

Hi,
I have a satellite receiver with Ethernet LAN port connection point. I also have wireless network in my house to connect my computers wirelessly to internet.
Is it possible to make this satellite receiver wirelessly connected to my wireless home network by using WRT54G router attached to it?
If yes:
1)Which terminal of WRT54G router I must use for interconnection with satellite receiver ?
2)What I should do to configure WRT54G to achieve my goal, and how?
Thanks,

Thank you very much for the first reply.
However let me simplify my question this way:
In order to make satellite receiver part of my wireless home network, is it possible to use WRT54G as wireless adapter by connecting it with an Ethernet cable to LAN terminal (which has Ethernet connector) of the satellite receiver?
If the answer yes:
WRT54G has 4 Ethernet connectors marked 1,2,3&4 for LAN and one marked as Internet for ADSL modem.
1) To which connector of the WRT54G I must connect the cable end coming from satellite receiver LAN terminal?
2) What should I do (step by step please) to configure WRT54G to achieve my goal?
Thanks.

Is there a way to create a virtual network using C# and the Azure SDK/API?

I don't see a clear way to create an Azure Virtual Network using the SDK.
I have all the methods to create the virtual network configuration, but no way to submit it:
IList<string> VirtualNetworkAddressPrefixes = new List<string>();
IList<string> LocalNetworkAddressPrefixes = new List<string>();
IList<NetworkListResponse.DnsServer> DNSServers = new List<NetworkListResponse.DnsServer>();
IList<NetworkListResponse.Subnet> Subnets = new List<NetworkListResponse.Subnet>();
NetworkListResponse.Gateway Gateway = new NetworkListResponse.Gateway();
IList<NetworkListResponse.LocalNetworkSite> LocalSites = new List<NetworkListResponse.LocalNetworkSite>();
IList<NetworkListResponse.Connection> Connections = new List<NetworkListResponse.Connection>();
VirtualNetworkAddressPrefixes.Add("a.b.c.d/cidr");
DNSServers.Add(new NetworkListResponse.DnsServer() { Name = "TestDNS1", Address = "a.b.c.d" });
Subnets.Add(new NetworkListResponse.Subnet() { Name = "Subnet-1", AddressPrefix = "a.b.c.d/cidr" });
Subnets.Add(new NetworkListResponse.Subnet() { Name = "GatewaySubnet", AddressPrefix = "a.b.c.d/cidr" });
Connections.Add(new NetworkListResponse.Connection() { Type = LocalNetworkConnectionType.IPSecurity });
LocalNetworkAddressPrefixes.Add("a.b.c.d/cidr");
LocalSites.Add(new NetworkListResponse.LocalNetworkSite()
Name = "On-Prem",
Connections = Connections,
VpnGatewayAddress = "a.b.c.d",
AddressSpace = new NetworkListResponse.AddressSpace() { AddressPrefixes = LocalNetworkAddressPrefixes }
Gateway.Sites = LocalSites;
Gateway.Profile = GatewayProfile.ExtraLarge;
NetworkManagementClient netMgmtClient = new NetworkManagementClient(CloudCredentials);
NetworkListResponse netlistresp = GlobalSettings.mainWindow.netMgmtClient.Networks.List();
netlistresp.VirtualNetworkSites
.Add(new NetworkListResponse.VirtualNetworkSite()
Name = "TestVirtualNetwork",
AddressSpace = new NetworkListResponse.AddressSpace() { AddressPrefixes = VirtualNetworkAddressPrefixes },
DnsServers = DNSServers,
Subnets = Subnets,
AffinityGroup = "East US",
Gateway = Gateway,
Label = "LabelValue"
I have also created the entire XML response and sent it to the NetworkManagementClient -> Networks.SetConfiguration() method, but it appears this command expects the virtual network to already be in existence. If anyone could give guidance, it would be
appreciated.

Hi,
As discuss above , we have to create the XML response ,before that first you have to
GetConfiguration() details of existing virtual network.
string.format("@<NetworkConfiguration xmlns:xsd='http://www.w3.org/2001/XMLSchema' xmlns:xsi='http://www.w3.org/2001/XMLSchema-instance' xmlns='http://schemas.microsoft.com/ServiceHosting/2011/07/NetworkConfiguration'>
<VirtualNetworkConfiguration>
<Dns />
<VirtualNetworkSites>
<VirtualNetworkSite name=""{0}"" Location=""{1}"">
<AddressSpace>
<AddressPrefix>10.0.0.0/8</AddressPrefix>
</AddressSpace>
<Subnets>
<Subnet name=""Subnet-2"">
<AddressPrefix>10.0.0.0/11</AddressPrefix>
</Subnet>
</Subnets>
</VirtualNetworkSite>",Networkname,location)+(@"<VirtualNetworkSite name=""demodsf1"" Location=""West Europe"">
<AddressSpace>
<AddressPrefix>10.0.0.0/8</AddressPrefix>
</AddressSpace>
<Subnets>
<Subnet name=""Subnet-1"">
<AddressPrefix>10.0.0.0/11</AddressPrefix>
</Subnet>
</Subnets>
</VirtualNetworkSite> </VirtualNetworkSites>
</VirtualNetworkConfiguration>
</NetworkConfiguration>")
you have to append the node for existing node with new values , i got it its adding new virtual network
Best regards,

How do I extend my AirPort Extreme network using airport express

How do I extend my AirPort Extreme network using airport express

see http://support.apple.com/kb/HT4145 and other support articles
and/or
https://discussions.apple.com/thread/4462789?start=0&tstart=0
and many other discussions on this forum about this topic.

How can I set up a wi-fi network, using one time capsule and two airport express

how can I set up a wi-fi network, using one time capsule and two airport express ?
The time capsule is near the Mac. ok
The first Airport is on the corridor, ok, works well and the App on the iPad signals so, ok
But when I plug the next Airport on another room nearby nothing happens, and signals disconected ....
is the signal so weak that is not able to go to ono room to the other ?

Well, even if you have the first express set up to extend the network, the second express can only extend from the TimeCapsule.
Maybe you got walls of sheetrook in the way, or kitchen/bathroom tiles, etc, dampening the signal rapidly.

Cannot extend my network using AirPort Express

I just purchased a Time Capsule (2TB) and replaced my Airport Express WiFi. My intention was to expand my network, using the AirPort Express to expand the Time Capsule signal. I have tried several times and cannot get it to work.
Using AirPort Utility, I set up the Time Capsule successfully, making certain the "Allow the network to be expanded" box was checked off.
After resetting my AE, I plugged it in, it was detected by AirPort Utility, and I set the AE to expand the network, using the same network name, security, and password. When I save the settings and update, the AirPort Uitility returns an error stating that the AE unit could not be located. AE unit is flashing amber (slowly).
What DID work was connecting the AE to the Time Capsule with an ethernet cable, but this is not ideal, since I want to locate the AE away from the TC and wish to do it wirelessly.
Can someone offer some helpful suggestions that will work?
(Running MacBook Pro w/ OS X 10.7.2 and AirPort Utility 5.5.3.)

I would suggest the following:
Please move the AirPort Express (AX) to the same room as the Time Capsule and perform a Factory Default Reset as follows:
Pull the AX from power
Wait a few minutes
Hold in the reset button and continue to hold it in for an additional 8-10 seconds while you simultaneously plug the AX back in to power
Release the reset button after the hold period, and allow 40-45 seconds for the AX to display a slow, blinking amber light
Temporarily, connect a spare Ethernet cable from one of the LAN <-> ports on the Time Capsule to your AX
Open AirPort Utility and click Manual Setup
Click the Base Station tab below the row of icons to name your AX, assign a device password and adjust Time Zone settings
Click the Wireless tab next to the Base Station tab and adjust your settings as follows:
Wireless Mode = Extend a wireless network
Wireless Nework Name = Same name as your Time Capsule wireless network
Enter a check mark next to Allow wirelss clients
Wireless Security = Same setting as your Time Capsule wireless network. You may need to refer to the Time Capsule settings if you are not sure what setting to use
Wireless Password = Same password as the Time Capsule wireless network
Confirm Password
Click Update to save your settings
Close AirPort Utility and disconnect the Ethernet cable as soon as you see the message that the settings have been stored successfully on the AX
Wait 40-45 seconds for the AX to restart and display a green light
You can now locate the AX where it is needed, assuming that it can receive a good wireless signal at its new location
Post back on your results

I have a G5 mac using ver 10.4.11 and a newer mac using ver 10.8.4 these are networked. using the new mac i looked up my my photo on the old mac. It then said you need to upgrade your library which it did. Now the old mac can not open the photos

I have a G5 mac using ver 10.4.11 and a newer mac using ver 10.8.4 these are networked. using the new mac i looked up my my photo on the old mac. It then said you need to upgrade your library which it did. Now the old mac can not open the photos and say that I need to upgrade my I photo to a newer version. The old mac has no more support from apple in software update so I am not sure where I should go from here. can I use new soft ware with the old mac

The other part of the upgrade message was a warning that once you upgraded you would no longer be able to open the library with the old version which is exaclty what you did and what happened when you choose to continue
The iphoto library needs to be upgraded to work with this version of iPhoto. Your photo library will not be readable by previous versions of iphoto after the upgrade. The upgrade process may take several minutes depending on the number of photos in the library. Cancel or upgrade.
So now your choices are to not use iPhoto with the previous version using it onky with the newer version, restore your backup from before you did this upgrade or purchase iPhoto Library Manager and use it to rebuild the library using the older version of iPhoto (instructions are on their web site) thereby downgrading it (without projects)
LN

HT5022 I'm trying to add a "new client" to my wireless network using Airport Utility, but I can't find that option in the new version. I've downloaded all available updates of the OS and the utility.. Help!

I'm trying to add my HP wireless printer as a "new client" to my wireless network using Airport Utility, but I can't find that option in the new version. I've downloaded all available updates of the OS and the utility.. Help!

Why would you need to ADD a new Client. Unless the APE sytem is completely different then any other Wireless router the printer should get an IP address from the router. That is IF the printer is setup to get an IP from the LAN DHCP server.
Now you may want to make that IP it does get a Staticly assign IP address so it never changes, which will screw up printing if it does change. But i don't know if you can do that with APE routers.

Can't connect my P1102w printer to my wireless network (using Mac OS 10.6)

I have a vanilla home wireless network (D-Link to a cable modem), and a MacMini running OS 10.6.8. My Mac laptop and 4th. Gen iPad work seamlessly. But my hours-long attempt to connect my new HP P1102w to the network has been totally frustrating, despite close study of the pdf documentation, the printer's self-test/Device configuration sheet, browsing this forum, watching a slew of YouTube/HP videos, and following all manner of directions.
The only consolation is the printer works fine on its USB connection.
Here are some issues I've encountered that have stopped me in my tracks:
Carefully following both the pdf instructions and HP's online how-to video, I get through Step 6 w/ no problemn. but then I go to Step 7, which says:
" Under Communication Mode , click Infrastructure , select your network SSID from the Available Network Names (SSID) list, and then click the << button."
Problem is there's nothing of the kind in that window. All I see is a status of the Wireless: enable or disabled (depending on a choice). And even if I try selecting Enabled, it switches right back to Disabled. Aside: I note the printed instructions show a copyright date of 2011. That's ancient history in the CPU world.
Other issues: The only IP address I can find for the printer is the IPv4 address, but that's only for Direct Print Configuration. Is that the IP address I'm looking for?
The printer's hardward address, I assume, is its MAC ? Boy, I could sure use clearer use of language here.
So, needless to add, I'm stuck. It seems it should be THAT hard, but so far nothing I've been able to find on HP support or the forums seems to help. Thanks for any advice you can provide.
PS. I'd hate to have to return this printer because I'm a two decade HP printer lover, but, alas, I may have to if I can't find a solution.
Northwest John
This question was solved.
View Solution.

Hi @Northwest-John,
I see by your post that you are unable to setup the printer on the wireless network. I can help you.
Update the printer's firmware by the USB connection just to make sure that isn't causing any issues with the printer's Embedded Web Server (EWS) not allowing the proper changes. HP LaserJet P1102w Firmware Update Utility.
The newest version is 20130703, which you can compare by printing the configuration page.
Power cycle the router and restart the Mac.
The printer won't recognize the network name if there usually is any symbols or spaces in the network name.
Make sure Safari is set as the default browser. Sometimes the Embedded Web Server (EWS) won't open in other browsers. Open Safari, across the top select the Safari menu, select Preferences, General, set as default.
Turn the printer off, hold down the wireless button and cancel (x button) while turning the printer back on and don't release the two buttons until the printer stops making noise.
Print out a configuration report and make sure the SSID and IP address are cleared.
(hold down the x button and when the printer makes a noise let go)
Connect the USB cable from the printer to the Mac.
Go to the Apple, system preferences, print and fax.
Double click on the P1102w.
Open the utility.
Click printer setup.
Click HTML config.
This should open the Embedded Web Server for the printer.
Click the Networking tab.
Click Wireless from the list on the left.
(Click Enable if you have this option)
Under Communication Mode , click Infrastructure.
Select your network SSID from the Available Network Names (SSID) list and then click the << button so the network name moves over to other box.
From the Security Mode pop-up menu under Authentication , click WEP, WPA/WPA2 or open . Your selection depends on which Wireless Security Protocol your network uses.
Make sure you select either hexadecimal or alpha depending on your password. (very important)
Apply the settings.
In the confirmation box, (changes have been saved) click OK.
You should get a solid blue light on the printer shortly.
Then all we have to do is delete the USB driver and add the network driver.
Click on the Apple.
Click system preferences.
Click the print and fax icon.
Highlight the printer and click on the - sign to delete the printer. (USB driver)
Disconnect the USB cable.
Then click the + sign and select the printer from the list and click add. (P1102w bonjour)
Test the printer.
If you have any issues with the HTML config opening then do the following steps:
Close any applications.
On the Apple menu bar, click Go, computer, MAC harddrive, Library, Printers, HP, LaserJet, click on folder for your printer, click on EWS browser or HTML config, click the Networking tab, click wireless on the left and fill out your information. (make sure infrastructure is selected) Apply settings.
Then delete the USB driver and add the network printer.
Let me know if you are still having issues with filling out the EWS for the printer.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Setting up a home network using the new USB551L modem

I have recently switched from the 3G USB760 modem to the new 4G LTE USB511L modem. Since I live in a very rural area, it is one of the few internet options that I have and I am forced to use it for my home. I previously set up a wireless network using the previous modem by connecting a wireless router to my computer by ethernet cord. I then went under the properties of the connection in order to allow other computers/devices to use the connection. Since switching to the new USB modem, the network does not appear under the list of options when using the Windows 7 network connections icon in the lower right corner of the screen. I am trying to set up a similar wireless network for my house but I am having difficulty. It seems that everything will connect to the wireless router but the router is lacking internet connection. Any advice is appreciated.

Your best Option use th eUSB551L in a Hybrid Router:
The MBR95 will work for your situation plus it has 4 etherent ports if you need it, you can connect your network/wireless printers, android, ipad, ps3, xbox, nintendo wii, DVR, satellite, etc....
http://3gstore.com/mbr95
Combine it with a Full Band 3G/4G Hybrid Antenna and you got the best of all worlds
http://3gstore.com/product/3047_3g4g-full-band-outdoor-omni-antenna.html

Setting up a small business network using mac and windows pcs

Setting up a small business network using mac and windows??

Ok that sounds great. What is your actual question as it relates to AirPort networking? Is it: Can I set up a wired/wireless network with an AirPort base station that support multiple Mac & PC clients? If so the answer is yes.
If, instead, it is how to I configure an AirPort network to support a small business you will have to provide more details on both your networking & computing equipment in order for any of us to help you.

Multiple networks using single network adapter

Hi,
If I have only single network adapter in a OVM server (or single bond interface bond0 created from two network adapters), is it possible to separate networks for
VM management, live migrate and VM public networks using any mechanism, say by creating VLANs? I am having two 10G adapters in each of the VM server
and would like to separate traffic of each of these networks. Thanks in advance.

Hi,
10G adapter is the best NIC performance so with two NICs like this, i recommand you to use the bond0 (mode 1) for fault tolerance and use the VLAN technology to separate the Networks.
Note that Oracle VM support the VLAN configuration.
I hope this can help you
Best Regards

Segregating Network using WRT54GS

Similar Messages

Maybe you are looking for