Selection Contains no media Error?

When exporting using Compressor from a time line in FCP I get a "selection contains no media" error.
Any suggestions?
Charles

Your IN and OUT points are not set for in the sequence. Use your UP arrow to get to the start of the sequence and use 'I' to inset your IN and go to the end of sequence and mark with 'O'. All should be fine now with compressor.

Similar Messages

  • "Selection contains no media"  error message in compressor any ideas??

    “Selection contains no media”
    This is a message I get often when I try to export from compressor 2.. There is media.. The way around it is to copy the selection and paste it into a new project...
    Any ideas on what wrong??

    Your IN and OUT points are not set for in the sequence. Use your UP arrow to get to the start of the sequence and use 'I' to inset your IN and go to the end of sequence and mark with 'O'. All should be fine now with compressor.

  • Can't export to Compressor. "Selection contains no media"

    I get a message that says "selection contains no media", but there is clearly media on the timeline that plays fine in the viewer. Other projects export fine and using quicktime conversion to export works fine too.

    Pentent wrote:
    Interesting. Losing the in and out points on the timeline solved the problem, but now what if I wish to just send a segment to compressor and not the entire sequence?
    Exporting with in and out points works okay in other projects. I'm a bit confused.
    Is the sequence in question not in your main browser tab? If you're someone who likes to, say, option-click bins to open them in tabs behind the main project tab - I like to do this - then is a known issue when attempting the Export > Using Compressor workflow. (Sequences exported this way must be in the main tab, not in a floating tab or tab behind the main tab).
    I've never experienced this error in any other circumstance - I export Using Compressor all the time, with In and Out set, so that in-and-of itself isn't the exact cause...

  • "Selection contains no media" What happened??

    “Selection contains no media”
    This is a message I get often when I try to export from compressor 2.. There is media.. The way around it is to copy the selection and paste it into a new project...
    Any ideas on what wrong??

    This is typical symptom of sequence corruption in FCP. About the only thing you can do as an end user is create a fresh sequence, then copy and paste your clips over. However, you mention that you copy and pasted into a new project - so are we to understand that a new sequence in the existing project didn't work?
    (To put your mind at ease, um, somewhat, this is an FCP issue, not a Compressor issue.)

  • "Selection contains no media" ????

    This is the error message I get when I select "export to compressor" on ANY sequence in the browser for ANY project I open. Restarting FCP or the computer doesn't solve anything .. strangely I can still export uncompressed QT movies of any of these sequences, but I can't send anything out to compressor all of a sudden. Help!!! Thanks!!!

    Yep! When you create a quicktime movie your video is compressed.
    gig
    sorry to say gig, but what you say is NOT true.
    Quicktime itself is nothing else than a container.
    Depending on the settings you do or do not compress.
    Like I said: When you export with current settings, then actually nothing changes. You only make the movie available outside FCP.
    Even if you make a Reference Movie (=NOT selfcontained) then this Reference movie is a file that directly points to your orignal (or filtered and rendered) moviefiles.
    To go short: As long as you don't alter settings, Export Quiktime movie does not change your movie in any way.
    Rienk

  • Send to compressor: warning: "selection contains offline media"...

    "Do you wish to continue to export?"  I've isolated multiple sections of my timeline and it still says this.  I looked the timeline over and could find no media that appeared to be offline.  I played the the timeline.  I went ahead and compressed and it took a really long time for an 8 minute show.  I have yet to look at the results.  One other person wrote in with this problem with no answer given.

    I've had it, too.  Compressor and FCP X are still pretty buggy.  Report it.

  • "The selected file does not contain audio media ..."

    I'm using Premiere Pro CC in Windows 7. A week ago I created a project using media from an external hard drive. I opened the project today to make changes to it, and a number of the .MTS files show up as missing. When I click on "Link Media" and locate the file -- which shows up as being on the external drive -- I get the following error message: "The selected file does not contain audio media used by clip references in one or more sequences. These audio clip references will be deleted, and cannot be undone. Do you want to continue?" I have canceled out of it because I do not want to damage my project irreparably, but I'm trying to determine the best course of action in re-linking these clips that are essential to the project. (I did apply a Left Fill to all the audio in the project, but I don't know if that would cause a problem, or if it did, how I could remove that effect. I've tried to re-link with several previous autosave versions of the project, only to get the same result.)

    Try this:
    FAQ: Why are some codecs and sequence presets missing from my installation of Premiere Pro?

  • The SQL statement "SELECT * FROM "SDBAH"" contains the semantics error[s]:

    Hello all together,
    actually I try to implement an user interface for using BRTools from a J2EE Application.
    I created a datasource-alias "BRTOOLS" using netweaver administrator.
    inside the implementation i execute the following code:
    DataSource ds = (DataSource) ctx.lookup("jdbc/BRTOOLS");
    Connection con = ds.getConnection();
    String query = "select * from SDBAH;";
    Statement stmt = con.createStatement();
    try {
       ResultSet rs = stmt.executeQuery(query);
    As the result I get the following message:
    The SQL statement "SELECT * FROM "SDBAH"" contains the semantics error[s]: - 1:15 - the table or view >>SDBAH<< does not exist.
    Using SQLplus or dbconsole I can see and use the table SDBAH. The table scheme is "SAPSR3DB"which is the standard scheme for J2EE.
    If I try:
    select * from SAPSR3DB.SDBAH;
    I get the same result.
    What is wrong in my constellation?
    Thank you very much in advance.
    Greetings Stephan

    Dear Yordan,
    yes I did a restart of the whole system.
    If I do a wrong lookup:
    e.g:
    DataSource ds = (DataSource) ctx.lookup("jdbc/BRToolsFailure");
    where Alias  "BRToolsFailure" does not exist, I get
    Object not found in lookup of BRToolsFailure.
    So I think that the Alias of the default data source is right and visible.
    Next try:
    I use an already existing alias "ADS" in my code and get the same message:
    The SQL statement "SELECT * FROM "SDBAH"" contains the semantics error[s]: - 1:15 - the table or view >>SDBAH<< does not exist.
    If I extend the tablename with the scheme-name "SAPSR3DB" I get the following:
    The SQL statement "SELECT * FROM "SAPSR3DB"."SDBAH"" contains the semantics error[s]: - 1:24 - the table or view >>SDBAH<< does not exist
    When I use SQLPLUS SAPSR3DB/password and call:
    select * from SDBAH;
    I get a result like expected.
    Thanks a lot,
    Stephan

  • New iTunes on Mac doesn't allow me anymore to select all songs and 'Get info' to adjust the volume, like the old one. It says"your selection contains more than one type of media". They are all songs! Help please!

    New iTunes on Mac doesn't allow me anymore to select all songs and 'Get info' to adjust the volume, like the old one. It says"your selection contains more than one type of media". They are all songs! Help please!

    Raya Alfa wrote:
    ...there are some that are mp3 and it will be extremely hard to pick them from the lot.
    Not true. Select "Kind" as a sort category by right clicking the headings
    Then click to sort by Kind
    If your Import Settings are for Apple Lossless, AIFF, AAC or whatever the majority of your files are, convert MP3s to that file type.
    I've presently got 17,000+ files in my library, and they're ALL MP3 or M4B(Audiobooks). If they weren't when I got them, I converted them.  Saves a LOT of hassels with just this type of situation. Besides I have two non Apple MP3 players that WON'T work with other file types besides MP3 so, EVERYTHING I have has to be MP3.

  • "one or more of the items in your selection contains Aperture albums that are not supported in iphoto".

    I have some folders in iPhoto called 'Recovered Folder'. When I try to delete them I get this message: "one or more of the items in your selection contains Aperture albums that are not supported in iphoto".
    I don't use Aperture (did install it to try it out), and have deleted Aperture App from my Mac.
    How can I get rid of these fodlers?

    i finally figured this out:
    fyi, iphoto and aperture can now share (i.e., access) the same library. apple details it here:
    http://support.apple.com/kb/HT5260?viewlocale=en_US&locale=en_US
    i use both iphoto and aperture, and i suspect something went amiss, at some point, while aperture was accessing my iphoto library.
    this is how i fixed the problem:
    i launched aperture, then (per the instructions linked above) switched to (i.e., accessed) my iphoto library. i was then able to delete the "recovered folder" and the album it contained. i then quit aperture and relaunched iphoto.
    NOTE: at that time, although i expected the "recovered folder" to be gone, it was still present. but this time, i was able to delete the folder from within iphoto without the "contains aperture items" error message.
    (Sparky030405, i realize you've since deleted aperture. while i can't say my method is the *only* way to solve this problem, it's the way i was able to solve it. so, you might consider reinstalling aperture in order to delete the folder, then uninstalling aperture, once again.)

  • R1800 from Aperture - discrepancies in settings causing "media errors"

    After upgrade to SL i have been having some issues with printing to R1800 - i consistently get "media errors" when trying to print edge to edge on some media types.
    Aperture and the epson print drivers do not seem to play together well... in most cases when you modify the default paper to say 4*6 sheet feed no border it switches to roll paper feed which in my case is always empty - hence the error messages about out of media...
    You can see the incorrect setting once you have set all your prefs in the print dialog when you go back to the print settings dropdown (under printer selection on my window) and select print settings... for certain paper selections (in my case) A4/sheet/borderless + 6*6/Sheet/borderless all end up with "roll paper borderless" which means i get the "media error".
    Can anyone else confirm this issue, and if so is there any clue as to whether this is an Aperture issue or an Epson driver issue.

    Can anyone else confirm this issue.
    I have been able to print edge to edge on 4*6 and A4 from Photoshop and iPhoto so i suspect this is an issue with Aperture.

  • "Add Media Error" - Premier Elements 7

    Question for everyone.
    My laptop (with P.E. 8) is in the shop so I am using my P.E. 7 edition on my home computer to create a simple project.  After attempting to add a four media clip (by the way, all 4 clips are very small, short), I am getting this error pop-up:
    "Add Media Error - There is not enough memory to add the requested media."
    Now, I can tell you that on my computer, 90% of my work is sitting in an external, 2 terabyte hard drive.  I have over 200 Gigs of free space on my home computer.  This new, short project is the one of the only projects currently sitting on my desktop.  There is no way that I am out of memory.
    Currently, while typing this question on this forum, I'm defragmenting my hard drive and doing a disk clean up.  Perhaps my settings are off?
    Any ideas?
    Thanks,
    David

    First, go to the http://forums.adobe.com/community/premiere/hardware_forum and click the link just above the messages to read several articles
    The aim in that forum is mostly CS5, but still some very good information
    Second, figure out the computer you need based on the camera you select... BEFORE you buy the camera
    This message has a really good graphic about requirements
    CS5 Requirements http://forums.adobe.com/thread/810750?tstart=0
    My CS5/AVCHD 1st Impressions http://forums.adobe.com/thread/652694?tstart=0 includes a link to the computer I built... since the GTX 285 is no longer sold, I would now go with a GTX 460 or whatever is the current "best bang for the buck" - AND I would buy 4Gig-by-3Sticks memory to be able to expand from 12Gig to 24Gig if needed
    For my home hobbyist, family movies (which means that I am not trying to recreate Star Wars with video effects or many layers) AVCHD editing is "as smooth as spreading warm butter on hot toast" (also the MP4 video from wife's Flip camera)
    My 3 hard drives are configured as... (WD = Western Digital)
    1 - 320G WD Win7 64bit Pro and all program installs
    2 - 320G WD Win7 swap file and video project files
    3 - 1T WD all video files... input & output files

  • Stage 4 Multiplexing - Media error in Power calibration 0x73,0x03

    Try to burn a DVD the project I made.  Everything is fine until it goes to stage 4 Multiplexing & Burning  - the system shows a Media Error in the Power Calibration  0x73,0x03 when this come up it will eject the dvd.  I never had a problem like this. System always worked fine.  Any help on this?  Thank you, John

    Hi
    As I remember it - it used to be when using Cheap Brands of DVDs e.g. Memorex or NoName ec.
    Else
    Multiplexing Error
    Multiplexing error is a very complex problem due to many things (long long list following) - one common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
    So first - turn on TV-Safe area and move any object well inside of this.
    Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
    Now my long long list on Multiplex Error
    LONG LONG LONG LIST
    Multiplexing Error
    PART One.
    Use of strange video/audio material e.g. .avi, .wmv, .mp3 etc.
    I only use.
    Video - StreamingDV (miniDV tape via FireWire) and
    Audio - .aiff (as on audio-CDs) (else converted to this .aiff 48KHz)
    Photo - .jpg (.bmp known problematic)
    Chapters !
    A.    Using strange letters in video project name e.g. +,/; etc. keep to a-z and 0-9 strange letters in project name e.g. +
    as described by Donnyboy69.  Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
    B.    Location of Chapters
    • Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
    • Not in a transition (or within 2-3 seconds from it)
    Important when from iMovie HD6 or previous - Now also observed when using FCE 4
    PART Two.
    from Robert Modero.
    "Multiplexing Error. Problem during initialization of tracks"
    Simply remember to add subtitles to your Quicktime files and menu buttons.
    Once I did that, I was back in business.
    from Boise Jim
    Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
    I always makes a DiskImage first and test this so that it runs OK
    I use only - Verbatim DVDs
    I use only - DVD-R
    I burn at an as slow speed possibly e.g. x1
    This gives good DVDs
    PART Three.
    Multiplex Error
    Chuck, Chicago 2/7/2009.
    Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
    2. Disconnect any other external devices not absolutely needed.
    e.g. external USB/USB2 hard disks, other FW hard disks etc.
    3 Chapter marks in transitions - minimum 2 sec from
    FROM Bev.
    (Not a 'guy' but I will answer!)
    First, I do not think that mixing wide-screen and standard makes a difference in iDVD.
    Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taiyo Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
    Also, choose a slower burn speed, 4x or less.
    Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
    From. Boise, Idaho
    I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
    It worked, and I got a clean burn from iDVD.
    Hopefully this can help other people.
    by dheb0422
    Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
    One user more writes
    To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
    Video from both passed from FCE 4.01 with chapters
    One project worked fine in creating disk image file
    The other gave Multiplex Errors
    I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
    Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
    Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
    This time multiplex errors gone
    So had something to do with chapters
    So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
    After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
    That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
    When I removed "bad" chapter mark (and others in), no multiplex error
    As a final experiment, I moved "bad" chapter mark about 5-10 sec's beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
    I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
    Rich839
    In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
    Russ One - suggest this
    Multiplex Error-There was an error during muxing preparation
    One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
    Summary - What to try
    1. Chapters
    • Only A to Z and 0 to 9 in chapter title
    • No Chapter mark at very beginning of movie
    • No Chapter mark in or within 2 seconds from any transition in movie
    2. TV-safe area for buttons (no one outside this)
    3. Safe re-boot
    4. No other external devices connected - that are not needed
    SDMacuser adds to this
    • On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
    Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
    5. Minimum of 25Gb free space on Start-up hard disk
    6. Make a DiskImage first - reduces where problem originates
    7. Trash iDVD pref. file
    8. Make a new iDVD project
    9. Movies in project with same aspect ratio e.g. 4x3 or 16x9
    10. No other programs/applications running during iDVD process. e.g. Internet, screen & energy savers
    Yours Bengt W

  • SP2013: List does not exist / The page you selected contains a list that does not exist. It may have been deleted by another user

    There are dozens of entries regarding "
    List does not exist / The page you selected
    contains a list that does not exist. It may have been deleted by another user" and none of them are really SP 2013 so i thought I would create this entry. 
    I am getting the error above after creating a simple list with 4 columns.  the list is created during a new site definition activation but when I click on my list, I get the error above.  the list works if I deactivate the feature and re-activate
    it.  but has the error whenever the new site definition is created.  
    Has anybody encountered this issue on SP 2013?

    Hi，
    For your issue, there are plenty of possible reasons offered when we search this issue online.
    Here are similar issue posts, check whether they are helpful:
    http://sharepoint.stackexchange.com/questions/98239/list-does-not-exist-error-when-opening-the-views
    http://sharepoint2u.com/?p=56https://shareyourpoint.wordpress.com/2012/04/12/list-does-not-exist-the-page-you-selected-contains-a-list-that-does-not-exist-it-may-have-been-deleted-by-another-user-sharepoint-2010-error/
    http://spnovice.blogspot.com/2012/10/list-does-not-exist-or-does-it.html
    Best Regards,
    Lisa Chen
    Forum Support
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
    [email protected]
    Lisa Chen
    TechNet Community Support

  • KIMYONG:  "Service Component Container Not Running"  error 시 조치사항

    KIMYONG: "Service Component Container Not Running" error 시 조치사항
    Purpose
    WF Agent Listener 를 구동하고자 할때 아래 error를 발생하며 멈추게 됩니다.
    이를 조치하는 방법은
    ERROR
    CANNOT START 'WORKFLOW AGENT LISTENER - ERROR:
    "THE SERVICE ERROR COMPONENT CONTAINER"
    Solution
    전체적인 절차는 아래와 같습니다.
    1. apache 를 bounce 합니다.
    2. Workflow Mailer Service를 시작합니다.
    a. Workflow administrator Web Applications Responsibility
    b. Workflow Manager
    c. Click on Service Components icon
    d. Click on the Workflow Mailer Service link (Container column)
    e. Select Workflow Mailer Service
    f. Select Start from the list of values (top)
    g. Click on go.
    h. Wait until the Workflow Mailer service is "Activated"
    3. Workflow Agent listener Service 를 시작합니다.
    a. Workflow administrator Web Applications Responsibility
    b. Workflow Manager
    c. Click on Service Components icon
    d. Click on the Workflow Agent listener Service link (Container column)
    e. Select Workflow Agent listener Service
    f. Select Start from the list of values (top)
    g. Click on go.
    h. Wait until the Workflow Agent listener service is "Activated"
    4. Workflow Mailer를 시작합니다.
    a. Workflow administrator Web Applications Responsibility
    b. Workflow Manager
    c. Click on Notification Mailers icon
    d. Select Workflow Notification Mailer
    e. Select Start from the list of values (top)
    g. Click on go.
    h. Do the same for the workflow deferred agent listener
    Reference
    Note 559388.1

    Hi,
    I'm having the same problem as you did.
    I've tried pushing the button Go in the Oracle Workflow Manager - Service Components.
    And it showed
    An error has occurred!
    The Service Component Container is not running.
    Should I uninstall my Oracle Workflow?
    And install a new installation of Oracle Workflow?
    What does it mean by the "wfinstall"?
    Is it the Oracle Workflow Configuration Assistant? which I can access using the wfinstall.bat.
    Or should I replay the Oracle Workflow Configuration Assistant (wfinstall.bat) and choose Upgrade option?
    Or should I uninstall all of my Oracle installation and start installing from the beginning?
    BTW, what if I don't use (or have) OID?
    Is it required?
    Any clue would be grateful.
    Thanks.
    Buntoro

Maybe you are looking for