Self install Uverse Internet red blinking broadband light

I've been trying to setup my new Uverse internet service since my activation date (7/21 after 2pm) and the broadband light will not go solid green. I've tried all of the troubleshooting steps I could find and still nothing.

Hi ,
I am sorry about the issues you are having installing your service, but I will be glad to help. Try testing on the other phone jacks in your house. It can take a few minutes for it to sync up, but it should take less than 1 minute for it to start blinking green. I will also send you a private message to look into this issue further.
-ATTU-verseCare

Similar Messages

  • Red Blinking Message Light Indicator Back to Green

    On the BlackBerry Curve 8330, can anyone tell me please if it is normal once you receive any type of message, and the light on top blinks red, after about 15 minutes it goes back to blinking green even though I never checked my messages? You would think, especially with a BlackBerry that the light would continue to blink red until messages are checked?! Is there anything I can do to remedy this? Any programs out there third party or what not?...any free? Or is my phone defected? Thank you for your time and your input.

    Yes the coverage indicator is on, I want it to blink green. Again, I want to know why the red blinking light message indicator goes back to blinking green after 15 minutes and does not continue to blink red until I actually go into the particular message folder? Thanks anyways for your help.

  • Still have blinking amber light

    I've followed the instructions. I've searched the support board, and I still can't get my airport express to work. I've reset it to factory settings, I've unplugged the cable modem and left it off for 15 minutes then replugged everything.
    My Macbook "sees" the airport, it says the AX is working, but there's no Internet connection (blinking amber light). I have two AX's set up elsewhere just fine, but I'm trying to set this one up with no luck.
    HELP!

    Hi Mary,
    Welcome to the forum.
    First question is: How old is the Express that is a problem? If it is two years or older it may have reached the end of its life cycle.
    After you have reset it to factory settings, it should show up in the setup assistant or Airport Utility with its original Apple factory ID. When you join it to the system, do not name it the same name that you have named it before. What I usually do is add a word in front of the old name like "new" or add a number behind it. It may see the Airport but if the Airport is in actually not tied to your wireless system it won't connect.

  • MIFI4620LE Jetpack blinking amber light--does this mean the battery is bad? Should the unit operate without the battery installed if plugged in?

    MIFI4620LE Jetpack blinking amber light--does this mean the battery is bad? Should the unit operate without the battery installed if plugged in?

    The MIFI4620LE Jetpack does not work without a battery installed, even when connected to an external power supply.
    I personally think that was a dumb design. I would think the unit would use more electricity when continually charging the battery than just powering the unit it's self, but that's the way Novatel made them.
    If your Jetpack works with the battery installed and connected to an external power supply, but does not power on with power supply disconnected, I would say that the battery is defective or worn out.
    You should be able to go to a nearby Verizon Store and have them either test the battery or put a new one in it to see if it works. Then you will know if you need to spend the $$ for a new battery. OR if you always use your Jetpack at home, or in your car, just use the old battery connect to a power supply or your cigarette lighter and save the cash.
    As the Customer Support person stated, the slow blinking amber light is a normal state when the Jetpack is turned on and connected to Verizon's service.
    I hope this solves your problem.

  • Constant Red Broadband Light

    I have a problem with my broadband.
    On the 15th October I rang BT and requested my connection to be
    transferred to my new property on the 28th October. I then received an
    email stating that connection would be made on the 5th November.
    I then rang BT again stating that this date was incorrect and the
    changeover date should be the 28th October and immediately received an
    email confirming this new date.
    On the 28th I moved into the new property and the broadband was
    working fine. The 5th of November arrived and the broadband stopped
    working (going from a blue power light, a blue broadband light and a
    blue wireless light to blue power, red broadband & blue wireless).
    Since the 5th I have had 3 engineers come to my property, all of
    which have found no faults at the property (including the router) and
    almost daily calls from India but I still have no connection.
    I would appreciate your help immensely! Any thoughts?
    Solved!
    Go to Solution.

    Hi TerryTeo,
    Thanks for the post and welcome to the forum.
    A red broadband light usually indicates a problem with authentication.  Can I get you to check what details you are using within the hub manager?
    Open a web-browser and type http://api.home or http://192.168.1.254 in the address bar and then click Go, or press Enter.
    Click Settings
    Enter Hub password and click OK
    Click Advanced Settings
    Click Broadband
    Click Internet
    Under the 'broadband username' section make sure that the username you are using is [email protected]
    Please check this and then get back to us to let us know where we stand with this.
    Cheers
    Sean
    BTCare Community Manager
    If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
    We are sorry that we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

  • RED Blinking LIGHT

    I used blackberry software updater to update my phone then it had to restart and it almost did except the it came to 100% and the battery died to it shut down then when I turned it on it would came on but a red blinking light comes on every other second. I don t know what to do somebody please help me

    The red blinking light means that you most likely have a corrupt software because your downloading was interupted by a drained battery. You may have to re-install the software with the Blackberry Link by connecting your phone to the computer 

  • RAM Issues: 4GB installed, 1GB showing After blinking light

    Hey Folks,
    After doing some research online I found that my recent issue, which has come up in the past, was probably a RAM seating issue. The issue where the Fan begins running loudly at hyper speed. I forced a shut down, restarted up and saw no issue. Shortly there after the issue returned. I forced a shut down once more, but this time was met with a blinking power light.
    I remembered from past experience that it was a sign of RAM issues so I unplugged, unseated and reseated all four of the RAM on my cards. Initial start up was met with same response. In fact it wasn't until the 6th or 7th seating and reseating, and RAM position switch that I got the computer to start back up. (The initial successful start up was with one card and what should have been 2GB.)  I checked the About this Mac.. and saw Memory listed as 1GB 667  MHz DDR2 FB-DIMM. The 1GB threw me off because at that moment there should have been 2.
    Shortly there after I backed some things up and tried reseating the other card with the other 2 gigs in it. This time I was able to start up however the System still shows the Memory as 1GB 667 MHz...
    I did notice a single red light on one of the cards and am curious if this is trying to tell me anything, or if this is an indication of a poor installation. Also looking for any advice on why the computer is not seeing all 4 gigs, and if some of them may be out of service.
    Any advice would be much appreciated, and please pardon my lingo because I'm not sure all my wording is correct.
    Thanks
    MAC Pro 2007/08 running 10.6.8 2x2.66 GHz Dual-Core Intel Xeon

    Failed RAM.
    Stop beating yourself up over insertion technique. These things get mighty hot and they FAIL.
    If they have a reseller's sticker on them, like Otherworld computing or 1-800-Memory or such, call them and ask for lifetime warranty replacements. Otherwise, think hard about how much RAM you really need and go buy some.

  • Red blinking light as well as trailing broken black line going in a square on left side

    red blinking light as well as trailing black broken black line going on left side that goes in a square trail

    Did you ever fix this? My daughters is the same. Treated with tender loving care, we reset to factory and it disappeared but was back again after 2 or 3 days. Still in warranty so going to take to the genius bar, however a bit concerned that because it belongs to an 11 year old they are going to assume she's damaged it.

  • Yellow broadband light then no internet

    Hi there. Can someone please help me. For the last couple of weeks the yellow broadband light will come on on my home hub, then on my laptop it will disconnect me off the internet with the computer screen saying the yellow light is on unable to connect. It seems to happen the same time on the evening whenever we are on the computer and if this doesnt happen it seems that the internet will run slow for a short period of time then the speeds will return to normal.
    When the yellow light sign comes up on our computer screen we have to close the page then open the internet again and then it seems to be working again.
    I read somewhere about the 10 training period what is this? When did it start? How long does it go on for? and come this be what the problem is?
    I am on the old home hub been with bt broadband a year and a half, it comes off the asdl. I am not able to have bt infinity yet. Can somebody please help its driving us crazy. I reset everything, checked connections and its still the same.

    10 training period starts from when you are activated with BT and runs for 10 days, If you could post your hubs stats and BT speed test results, we might be able to offer help. However if you are in this 10 days, its very unlikely BT will want to know until this period has passed!
    To
    post the full stats from your router
    For homehub - 192.168.1.254
    Navigate to ADSL Settings or use the A-Z at the top right
    Click on More Details and then post the results.
    Run Bt speed tester and post the results from http://speedtester.bt.com/
    Mortgage Advisor 2000-2008
    Green Energy Advisor 2008-2010
    Charity Health Care Provider Advisor 2010-
    I'm alright Jack....

  • HT1551 after finish installing an update, the the status light keeps blinking and a picture of the connection between the micro USB and iTunes shows up - what is this about?

    after finish installing an update, the the status light keeps blinking and a picture of the connection between the micro USB and iTunes shows up - what is this about?

    The update failed - using a USB to microUSB lead (that Apple annoyingly don't include!), try to restore the AppleTV software to current version software using instructions here:
    http://support.apple.com/kb/HT4367
    Pay attention to differences in power connection depending on whether or not you have AppleTV2 or AppleTV 3.

  • I recently bought an Airport Express and connected it to my TimeWarner modem. Am able to surf the internet using my MacBook Air, iPad, and Apple TV, but the AirPort Express has a blinking amber light. How could I change it to a green light?

    I recently bought an Airport Express and connected it to my TimeWarner modem. Am able to surf the internet using my MacBook Air, iPad, and Apple TV, but the AirPort Express has a blinking amber light. How could I change it to a green light?

    The following may help: Wi-Fi base station: Understanding and resolving a blinking amber status light

  • Red blinking light & phone is unresponsive (8100 Series)

    I've had my Pearl for about 18 months and it's always been fairly reliable.
    Yesterday it got wet for the first time (I suspect this may be the cause of the problem...).
    Right away, I took out the battery and SIM card, dried the phone as best I could, and put the parts in a warm area.
    Now all I'm seeing is a series of red blinking lights:
    - blink, blink, blink (3 times, a half second pause, then)
    - blink, blink (and a 2 second pause before it starts again)
    I tried using a backup battery, and I tried it with and without the SIM card.
    Does anyone know what this sequence of blinks means?
    And, more importantly, how can I save my phone?? 

    the three blinks, a pause, and two more.. don't know what the blink meant or why mine started.. I connect to computer via bluetooth and wasn't connected when it began. I came here for answers and very surprised bb doesn't have a tech rep providing help.  & phone charged full the night before..
    anyway, followed advice to disconnect from battery and reconnect in certain order while plugged into wall socket.. tried a few times with a few minutes of complete 'no power' each time. the light would sometimes flash when only the wall plug was in with no sim or battery. I gave up and left it connected to the wall socket with sim and battery in and flipped it over so I wouldn't get annoyed seeing the blink. left it for 30 minutes and it still was flashing. stuck it in my pocket went to a friend's house and checked when I got there 10 minutes later. still flashing. threw it half way across the room (carpet floor) and it booted up fine. is on now and I'm not touching it until tomorrow. 
    not suggesting anyone throw it, could break it, but it worked for me. likely in conjunction with topping up the battery. who knows. they're touchy.

  • Red Blinking Lights on Photosmart 7760

    I have a Photomart 7760 that is now starting up from power on, blinks 10 times "green", and then continuous "red" blinking.  If I remember correct from another post, it said something about printer head.  So...question is what does this blinking sequence mean, and how to I correct it?

    Here is a link to a document you can follow for this issue:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=bpa00299&cc=us&dlc=en&lc=en&product=305375&tmp_t...
    I am an HP employee.
    Say "Thanks" by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as "Accepted Solution"

  • Airport extreme blinking amber light error when connecting to new modem

    I have just bought and installed a new modem gateway.  It is an Arris TG852G DOC 3.0 model with a built in WiFi router.
    After connecting it and activating it through Comcast, I reset, then reconnected my airport extreme MD0331LL/A Model No. A1408 to the new Arris
    modem, I am getting blinking amber lights on the base station.  I have internet connectivity, but I am still getting an amber light.  My wireless devices (ipad and iphones) all see the old network name and id and seem to work just fine.
    When I scanned for my airport base station in my airport utility (version 5.6.1)  to try to resolve the error message I get
    a message stating that the Airport Utility is not detecting any airport devices.
    I cannot reset the default settings as these buttons do not work within the Airport Utility.
    I suspect interference between the built in router in the Arris and I understand I need to operate it in bridge mode.  Can you please help me fix this.
    The COMCAST people are extremely unhelpful, and stated that this is not their problem but a problem with my router
    as they have provifded me  internet connectivity through the modem and the issue is my problem.

    Try connecting an Ethernet cable from your computer directly to one of the LAN <-> ports on the AirPort Extreme to see if AirPort Utility can detect the AirPort Extreme that way.
    If yes, click on the AirPort Extreme and then click directly on the word Status (2nd line on the summary page)
    A window will open to explain why the amber light is blinking
    If the message indicates that you need to configure the AirPort in Bridge Mode......
    Click the Internet icon at the top of the window
    Click the Internet Connection tab just below
    Change the setting for Connection Sharing to Off (Bridge Mode)
    Click Update at the lower right of the window to save the new setting and restart the AirPort Extreme
    You can disconnect the Ethernet cable that you were using to configure the AirPort Extreme now
    It would be a good idea to power off both the Arris gateway and the AirPort Extreme now
    Wait a minute
    Start the Arris first, and let it run a full minute
    Start the AirPort Extreme next the same way
    You should be all set

  • Home hub 3 broadband light flashing orange & purpl...

    Hi,
    Broadband has stopped working with a flashing orange & purple broadband light (7 days and counting)
    Have phoned bt but they failed to resolve the issue over phone - resetting, power off/on etc. Tried 4 different branded adsl filters, alternative router but still no connection. Only 1 main socket, no extensions connected, doesn't have a test facility(older style socket). Tried 17070 quiet line test - sounds clear. Phone line test reports zero faults.
    Details from home hub 3 Broadband > connection tab
    Line state: Connected
    Data Transmitted/Received (GB): 0.0 / 0.0
    Downstream: 7.938 Mbps
    Upstream: 448 Kbps
    ADSL Settings VPI/VCI: 0/38
    Type: PPPoA Modulation: G.992.1 Annex A
    Latency type: Interleaved
    Noise margin (Down/Up): 16.7 dB / 26.0 dB
    Line attenuation (Down/Up): 10.8 dB / 5.0 dB
    Output power (Down/Up): 17.9 dBm / 12.4 dBm
    FEC Events (Down/Up): 10905 / 0
    CRC Events (Down/Up): 11 / 0
    Loss of Framing (Local/Remote): 0 / 0
    Loss of Signal (Local/Remote): 0 / 0
    Loss of Power (Local/Remote): 0 / 0
    HEC Events (Down/Up): 31 / 0
    Error Seconds (Local/Remote): 121 / 3
    Broadband > Internet tab
    Connection time: Connecting  
    I suspect the issue is at the exchange, has bt disconnected me and plugged someone else in? Any thoughts welcome.

    you appear to have tried everything suggested by BT for purple/orange flashing constantly and not solved the problem.  the help pages then say if that has failed then contact technical support but I would contact the forum mods instead for help
    contact mods
    can take up to 3 working days for mods to contact you
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Maybe you are looking for