Send break not working in M9000 XSCF.

Dear All.
I'm giving "sendbreak -d 01" form xscf, its not bring my OS to "OK" prompt.
My XSCF version is
XSCF> version -c xcp -v
XSCF#0 (Active )
XCP0 (Current): 1072
OpenBoot PROM : 02.03.0000
XSCF : 01.07.0005
XCP1 (Reserve): 1072
could any guide me, what could be the problem.
Thanks in advance.
veerabose

Hi Veeraa,
You need to switch off the secure mode.
XSCF> setdomainmode -d 0 -m secure=off
Diagnostic Level    :min      -> -
Secure Mode         :on       -> off
Autoboot            :on       -> -
The specified modes will be changed.
Continue? [y|n] :y
configured.
Diagnostic Level    :min
Secure Mode         :off (host watchdog: unavailable Break-signal:receive)
Autoboot            :on (autoboot:on)Regards.

Similar Messages

Office 2010 MUI in Finnish and Save and Send function not working after upgrading to Lync 2013 MUI

Problem is as follows. Used to have Office 2010, Outlook 2010 and Lync 2010, everything was working. People used it in Finnish and seemly quite a many of them used the Talleta ja lähetä (Save and Send in Finnish) in Office products.
After upgrading Lync to 2013 version, with Finnish language pack installed with it, the Save and send does not work in Office 2010 if it is used with Finnish as display language. When you try to use it you get a Mapi error and reason is undefined or something,
hard to say what it is exactly in english as the error message is in finnish. On those machines if the display language is changed back to english the Save and send works as it should.
Any ideas?

The problem was caused by the Language Packs for Lync 2013 or Office 2013. Without them all works.
And if you want to just unisntall the 2013 lang packs, then you also need to repair install the office 2010 ones to make it work again.

Why does Adobe sendnow work and the newest and greatest Adobe Send does not work?

Why does Adobe sendnow work and the newest and greatest Adobe Send does not work? I wasted about 8 hours on trying to get Adobe Send to upload 269 files that amounted to 469MB. When it did not work I made a zip file and after a lot of wasted run time that did not work. The first situation gives little indication of when a file is loaded compared to Adobe SendNow. In both cases with Send it failed with a message like only the first 50 can be loaded. When I went and looked none of them had been loaded. With the zip file (I wanted to hide the individual files so they would not be counted) it appeared to work but very slowly and finally said it was done and I went and looked and it had done anything for oever 2 hours except a false "I'm runninng" indication.
Thus, I took a chance with Adobe SendNow and it works great. It never gave me a limit on the amount of files nor on the size of the complete job. It shows me one file at a time when it has finished with the file uploading it. SendNow has never given me any problems.
Why woiuld you want to change the program from SendNow to Send without the newest program being the best, fastest, user friendly program of the two? It just doesn't make sense to me. I suggest that Adobe keep SendNow working until Send is fixed. I would also suggest that SendNow and how it looks be kept, called Send, then modify Send one thing at a time until you get it to the point you need it to be for Acrobat. I have heard nothing good and now I have experienced it that Send is a piece of junk. I wasted most of my work day on giving Adobe the benefit of the doubt to find out I made a very bad decision to trust Adobe to make good decisions on the transfer of a function to another place .... both Adobe's responsibility.without making it painless for your customers that totally rely on you. Don't throw away customer confidence as it is very hard to get it back.

Funny how you answer to "troll". (What's your handle on AT&T forums?)
Yep! Verizon living up to it's contractual obligations by not releasing updates. Caveat emptor!
I think there are some reasonable expectations here to keep customer's happy. When one carrier offers upgrades there is an expectation the same will happen across all the carriers. We have seen that except Big Red.
Verizon could have said the update is in MS court months ago and stilled the voice of the disgruntled, or at least redirected it, but instead chose to be silent. Not for market share but for partial blame I think.
We will have to agree to disagree since you only see Terms & Conditions and I, see customer satisfaction.

SAP PI FTP sender adapter not working with SAP ECC over Itanium

Hi,
We have been running normally SAP PI 7.0 SP14 with no issue for a while.
We are now in the process of migrate the SAP ECC system from PA risc to IA platform. We are performing some tests between SAP PI and SAP ECC to check that the platform migration is not affecting us in any way and we have found that FTP adapter sender is not working anymore (receiver is working as usual).
We place some files in the new ECC system and when PI goes to retreive the files it is like it can not read anything. It gives no error but it does not pick any file. This is not happening with the old platform.
Does anyone have any idea?
Thanks a lot for your help
Diana

Hi,
I am using FTP connection and for the receiver it is working fine.
Thanks
Diana

HTMLDB_MAIL.SEND does not work with 11g

Hi Guys,
I have a simple application that uses HTMLDB_MAIL.SEND. I am running APEX 3.0 against an 11g database. When run against a 10g DB all is good. But with 11g I get
ORA-24247: network access denied by access control list (ACL)
I looked up the error which recommends altering ACL stuff, which I know nothing about. Is there a simple way to get rid of this error.
O.

Hi,
I have the same problem as you.
Colud you please explain me how did you resolve it.
Thanks
HTMLDB_MAIL.SEND does not work with 11g

IMessage send is not working on my ipad2. I can receive only.

iMessage send is not working on my ipad2. I can receive only.

make sure you are typing your message in the line BELOW the line with the camera icon, soon as you type in that location the send button will become active.
Regards, Ct

Have been trying all weekend to upload Jpegs- either Send does not work or shows files uploading then shows error- never had this problem with Send Now-16 images total size 92MB-largest image 13MB

Have been trying all weekend to upload Jpegs- either Send does not work or shows files uploading then shows error- never had this problem with Send Now-16 images total size 92MB-largest image 13MB

Hi Ciaran19,
Are you sending files from the Adobe Send interface, Adobe Reader, or the Outlook plug-in?
Have you checked to see whether the files that you're sending appear in the Recent Files/Sent Files list when you're logged on to https://cloud.acrobat.com? (It could be that they're uploading, but not being sent.)
It would also be worthwhile to send the files in smaller batches, to see whether a particular file or files is problematic, and causing the error.
Please let us know how it goes. If you're still having trouble, please let us know where you're sending from, and whether you're able to send the files in smaller batches. It would also be helpful to know the exact error message that you're receiving.
Best,
Sara

Powershell Script Send-zip not working when running in cmd

I found there is powershell send-zip script available in technet. I tested it and found that it works when the script is running under powershell env, but when it is calling in cmd env, I can see the zip file, but there is nothing in it. If
I add the "-noexit" switch it runs normally. Anyone have ideas what might be happening?
The orig codes is as following:
function global:SEND-ZIP ($zipfilename, $filename) {
# The $zipHeader variable contains all the data that needs to sit on the top of the
# Binary file for a standard .ZIP file
$zipHeader=[char]80 + [char]75 + [char]5 + [char]6 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0 + [char]0
# Check to see if the Zip file exists, if not create a blank one
If ( (TEST-PATH $zipfilename) -eq $FALSE ) { Add-Content $zipfilename -value $zipHeader }
# Create an instance to Windows Explorer's Shell comObject
$ExplorerShell=NEW-OBJECT -comobject 'Shell.Application'
# Send whatever file / Folder is specified in $filename to the Zipped folder $zipfilename
$SendToZip=$ExplorerShell.Namespace($zipfilename.tostring()).CopyHere($filename.ToString())
SEND-ZIP C:\abc\a.ZIP C:\a\a.bak

I've had the same problem with similar code found on another web site.
The reason the zip file ends up being empty is that the temporary $ExplorerShell object you created is deleted when the send-zip function returns,
and any incomplete copy operation that may still be ongoing at that time is aborted. (The copy operation is asynchronous, and continues after the CopyHere() function returns.)
To work around this, you need to add a delay loop before you return, waiting for the copied object to appear in the zip.
(Note that adding a fixed delay, like I've seen on other web sites, does not work: Small files appear almost immediately, whereas large file or worse still large subdirectory trees can take a long time to appear.)
Try changing the end of your routine to something like...
# Create an instance to Windows Explorer's Shell comObject
$ExplorerShell=NEW-OBJECT -comobject 'Shell.Application'
# Open the zip file object
$zipFile = $ExplorerShell.Namespace($zipfilename.tostring())
# Count how many objects were in the zip file initially
$count = $zipFile.Items().Count
# Send whatever file / Folder is specified in $filename to the Zipped folder $zipfilename
$SendToZip=$zipFile.CopyHere($filename.ToString())
# Wait until the file / folder appears in the zip file
$count += 1 # We expect one more object to be there eventually
while ($zipFile.Items().Count -lt $count) {
Write-Debug "$filename not in the zip file yet. Sleeping 100ms"
Start-Sleep -milliseconds 100
# Return deletes the $zipFile object, and aborts incomplete copy operations.

JMS-send operation not working in a SessionBean [OC4J10.1.3.1.0-standalone]

Salut,
i am envisaged with a nasty problem calling a message-send operation from
a method (transaction-type="required") inside a session bean (transaction-type="container").
This problem occured in OC4J 10.1.3.1 and may fail also in 10.1.3.0. The same
code run under OC4J 10.1.2.x without any problems.
The adressed JMS type is a OEMS JMS and fails to work regardless if the JMS ressource
is using a file-persistence or is running in-memory. Anyway the factory is a
jms/XAQueueConnectionFactory, so the created queue must support XA transactions.
Another test with an advanced-queue JMS provider succeeded.
As a consequence of this, i believe that the OEMS provider shall cause the problem.
The original code is quite unspectaculary:
* The non-surprising thing is, that the QueueConnectionFactory
* is a XAQueueConnectionFactory.
QueueConnectionFactory qcf = (QueueConnectionFactory) (jndiContext.lookup(MY_QFAC));
Queue q = (Queue) (new InitialContext().lookup(MY_QUE));
c = qcf.createQueueConnection() ;
QueueSession s = c.createQueueSession(false, Session.AUTO_ACKNOWLEDGE);
[... create a message ]
QueueSender qs = s.createSender(q)
qs.send(m);
qs.close()
s.close();
c.close()
The funny thing is, that the queue-session behaves as it is working outside
of a transaction context. Inside the JMX-Console you will notice the
arrival of a message and ... a cancellation of it. This would not surprise
me, if this code sequence would have been called outside of
a Session bean, cause the absence of a queue-session.commit does not
fix the send message in the jms ressource.
As a matter of fact the code is executed inside a Session bean and
the connection.createQueueSession will notice this and forget both
given parameters, and let the covering transaction take over of the
JMS ressource. But this does not happen (completly).
The acknowledge-mode has been modified (SESSION_TRANSACTED)
but the code still does not work!
After i recognized that the enlist-ment did not work, i
decided to enfore the use of XA transaction by using the
XA classes and methods of JMS.
I startet to cast the jndi-references and:
XAQueueConnectionFactory qcf = (XAQueueConnectionFactory) (jndiContext.lookup(MY_QFAC));
Queue q = (Queue) (new InitialContext().lookup(MY_QUE));
XAQueueConnection c = qcf.createXAQueueConnection() ;
XAQueueSession s = c.createXAQueueSession();
[... create a message ]
QueueSender qs = s.createSender(q)
qs.send(m);
qs.close()
s.close();
c.close()
The funny thing is ... the code worked without any problem until
the send operation, where i received an JMSException, containing
the text:
Oc4jJMS.Session.hpcl057.4e9c06e4:1112674930d:-7fff.41,true,SESSION_TRANSACTED]: An attempt was made to perform work in a XA-backed session without being enlisted. Either the session must be enlisted (using the JMS Connector or JMS Adapter) to participate in the global transaction, or a non-XA connection and a non-XA session should be used to not participate in the global transaction.
How bizarre, i thought the enlistment has been taken place by invoking
the c.createXAQueueSession or c.createQueueSession(false, Session.AUTO_ACKNOWLEDGE);
How bizarre how bizarre
any clues ????

OC4J JMS was changed to not auto-enlist in XA transactions.
In releases prior to 10.1.3 XA usage was not actually supported. (It did not meet all of the XA requirements when used with OC4J.)
Auto-enlisting by the JMS provider was also a spec violation, which was causing trouble for people who needed to do out-of-transaction work and had no way to do it.
In 10.1.3 XA usage is fully supported, but only when you use the JMS Connector. You can find the JMS Connector ("Oracle's Generic JMS Resource Adapter") demos here:
http://www.oracle.com/technology/tech/java/oc4j/1013/how_to/index.html#JMS
The JMS Connector is documented in the OC4J Services Guide, OEMS/JMS chapter.
-Jeff

"Send" button not working in Mail

Picked up Leopard on an iMac two days ago. Some of the time when I compose a new email, Mail works fine--I click "send" once I'm through typing and out it goes.
Other times--like this morning--I try to send an email and the "send" button is transparent and does not click. This is not a server issue. I tried adding the recipients to my address book in case there was some weird thing where that had to be done first. But to no avail--the "send" button won't click, nor will the "send" command within the toolbar or drop-down menus--and so I have no clue how I'm supposed to send this email if the button to do it is not working. Help!

Unfortunately, the SMTP and outgoing mail settings aren't the issue. The issue is that the "send" button is visible but un-clickable. I tested sending mail from all of my accounts and it works just fine--sometimes. Other times, I try to reply to an email or send out a new one and the "send" button does not allow me to send anything at all.

Send As not working with cached mode enabled

Hi
I am having some issues using Send As. We are running Exchange 2010 Version 14.2 (Build 247.5) and Outlook 2013.
I have done the following:
1. created a mailbox user
2. created a security group and added my own account
3. added the security group with Send As permission through ADUC on the mailbox user
4. Waited a day and tried to send as the mailbox user, but it fails
If I disable cached mode or use OWA it works perfectly. The mailbox is NOT hidden in the address list.
I have seen this behavior before, but can't remember the "fix"?
Lasse
/Lasse

Hi,
From your description, the send as permission works well via OWA or Exchange online mode, the send as permission is configured successfully. The issue is related to Outlook side, in your case, I recommend you create a new profile and check the result.
Hope this can be helpful to you.
Best regards,
Amy Wang
TechNet Community Support

Send button not working on sms after upgrade

My send is no longer working on sms after i upgraded. I have done factory setting and still not working . Any ideas of anything else i can try ? frustrated

I have same problem. Can open message. As if keyboard is frozen.
Unable to type then send. Also, tried shutting off preview.

Send button not working on Droid

I have a customer trying to sign a document using a Droid. They can fill in the signature but the Send button is not working.

Hi,
Please can you contact support , https://echosign.zendesk.com/hc/requests, and provide them with as much detail on the issue as possible including any screenshots. They can then investigate this for you.
Thanks,
Jat

Mailto and Send Link not working on Mac 10.4.6

Send Link and Mail To are not working Mac OS 10.6.4. I have been unsuccessful trying Mail, Gmail, and re-installing Firefox.
I have been using Add This to send the links in an email, but would very much like to use Send LInk.
I'd appreciate any suggestions.
== This happened ==
Every time Firefox opened
== Several months ago

Yes I did. First I used Mail, then changed it to Gmail. When neither worked, I re-installed Firefox and got rid of as many apps as I could. I tried both again - but no luck.
I have copied and pasted links into either of these mail programs or used Add On,which requires opening a new tab, finding and entering the email address, closing or switching back to the original tab, etc.
Thanks for your suggestion.

Problem with RoadRunner: RECEIVE is ok, but SENDING does not work

Apple Mail not working properly: Receive - OK, Send - not working
If anyone has encountered this problem, and found a fix, please let me hear from you. Until then, I have to use the web-based email for RoadRunner.
In a nutshell, I can receive mail, but I cannot send mail.

Mail->Preferences->SMTP->Edit outgoing mail server list and reenter the data. I have no issues w/RR's pop server account.

Send break not working in M9000 XSCF.

Similar Messages

Maybe you are looking for