Sender File adapter problem

Hi,
I have File to JDBC sceanrio,  File is on FTP server and data is added in file in every 15 mint.  while adding data to file its takes some time.
My problem : when data is being  added to file, sender adapter picks the file when addition of data is not completed. so it picks incomplete file and send to target.
What  can be the possible solution to be used for this problem or what configurtaion can be done in CC required.
Thanks
Laxmi Bhushan

Hi Laxmi,
is PI picking file in NFS mode or FTP mode?
With NFS mode, you can use setting wait for file modification check. Same setting is available for FTP but it doesnt not work for FTP.
Another option could be ask Source system to generate file with a temporary name & rename once file is writen completely.
Regards
Sushil

Similar Messages

  • Sender file Adapter, problem with proxy authentication

    HI all,
    i'm having some problems with the following scenario, i need to configure a sender file adapter which connects to a FTP server. To connect this FTP server i need to set a proxy (and so a username and a password), and i don't know how to do.
    From note 821267 seems that the proxy is not supported for an FTP adapter, but the are some workaround like the ones described in the following link
    Re: Proxy server inFTP adapter
    http://wiki.sdn.sap.com/wiki/pages/viewpage.action?pageId=57137
    They don't work in my case as i need to se two username (the one for proxy and the one for the ftp server) and i cannot force the proxy use for all XI applications.
    Can anyone help me?
    Thanks a lot
    Aldo

    Proxy is necessary to exit the customer local intranet. It's not possible to go outside network without going through the proxy server.
    I cannot set the proxy server in file adapter as it's not supported like described in SAp note,  a possible workarounf is to force the proxy server in the J2ee stack but in this way all PI calls would use that proxy..

  • Sender File Adapter Problem when text document is a single line.

    Hi All,
    I have posted this question earlier too. But did not get a proper answer.
    I am using File adapter to fetch data from a file system.
    My input data is: AA123BB45678AA345BB78564.
    It is just reading the first segment i.e.AA123 and not reading the remaining.
    How can I configure my Sender File adapter to pick this pattern of data? It works fine if I have line break after each record that is if the input is as below.
    AA123
    BB45678
    AA345
    BB78564
    In the above there is a Line break after each segment. So File adapter picks it fine.
    I have also tried using xml.A.endSeparator equals to blank in the module configuration. But it does not work either.
    Can anyone throw some light to this?

    Abhi
    I tried a different approach to send your file data In..
    You can get each line in the source structure in separate row as
      <?xml version="1.0" encoding="utf-8" ?>
    - <ns:SingleRowDT xmlns:ns="http://xxxxx.com/xi/pocs/sriram">
    - <Recordset>
    - <row>
      <rowElt>AA123BB45678AA345BB78564</rowElt>
      </row>
    - <row>
      <rowElt>AA123BB45678AA345BB78564AA123BB45678AA345BB78564</rowElt>
      </row>
    - <row>
      <rowElt>AA123BB45678AA345BB78564AA123BB45678AA345BB78564AA123BB45678AA345BB78564</rowElt>
      </row>
      </Recordset>
    Now you can use a suitable mapping logic to split the individual records into the 2 field structure as expected in the target..
    Trying your way would be a limitation on file adapter I think..Let me know if this helps..I can give you the content conversion config for this model..
    its simply
    RecordSet - Leave it empty
    RecordSet Seq -  Row, *
    Recordsets/msg - *
    row.fieldSeparator - 'nl'
    row.endSeparator - 'nl'
    row.fieldNames - 'rowElt
    ..So each line will be pulled into a single Row in the source structure and then u can apply a specific mapping to split into 2 fields for your target
    Regards
    Sriram V.
    Regards
    Sriram V.

  • Sender File Adapter - Problem with field separator

    Hi,
    I want to upload a CSV file into XI.
    The file contains a text part which uses from time to time quotation marks like this:
    SD,575757,383838,N/A,XYZ,"This is a text part",7676
    But besides there are lines like this:
    SD,575757,777722,N/A,XDE,FREETEXT,7575
    Has anyone any idea how to configure the file adapter to get it recognize the quotation marks not as field separator?
    I've already tried the enclosureSign parameters but that leads to an total unconverted line.
    Is it maybe possible to customize two field separators like this:
    Structure.fieldSeparator - ,"
    Thanks for any answer,
    Christina

    No, it doesn't work.
    I've specified now:
    Structure.fieldSeparator        ,
    Structure.enclosureSign         "
    Structure.enclosureSignEscape   ""
    Every line without quotation marks is converted fine. Lines with quotation marks stay like in the original CSV file and the whole line is put into one XML tag (still comma separated).
    Also the parameter fieldContentFormatting - nothing doesn't make a difference.
    Other ideas?

  • Content conversion in sender file adapter problem

    Hello,
    I receive a flat file with the following structure:
    HEADER;...fields;
    ITEM;...fields;
    ITEM;...fields...;
    HEADER;...fields;
    ITEM;...fields...;
    ...etc.
    and I am converting it to xml with the same structure. The Problem by the conversion is that the result looks something like this:
    HEADER;...fields;
    ITEM;...fields;
    ITEM;...fields;
    ITEM;...fields;
    HEADER;...fields
    HEADER;...fields.
    So, all the ITEM recordsets are ordered to one HEADER structure and the other HEADER structures have no ITEMs.
    Do you have a suggestion how I can get this right?
    Thanks!!
    Best Regards,
    Mircea

    Hi,
    Can you provide with the details of FCC parameters you have used ??
    The problem might be there in the occurance..
    Regards,
    Chandra

  • Mapping  problem due to FCC in sender file adapter

    Hi All
    I am doing File( Flat File ) to RFC Scenario.it is working fine..
    the problem comes in mapping with multiple records.
    FCC at sender file adapter is used
    my Data Type are :
    Source DT                      Target RFC import parameter(table).
    E2ED20*                            ITEM*
        KEY                                    VBELN
        VBELN                                 POSNR                                                
    E2E24*                                     CHARG
        KEY
        POSNR                             
        CHARG
    <b>*->>multiple occurence
    E2ED20  and E2E24 are 2 segment ,KEY is used in FCC to identify E2EDL20 & E2EDL24</b>
    My source text file is like this :
    E2EDL20                       0200
    E2EDL24                       xyz
    E2EDL20                       0201
    E2EDL24                       abc
    E2EDL24                       efg
    E2EDL24                       mln                      
    E2EDL20                       0202
    E2EDL24                       gty
    so the payload should be :
      0200   xyz
      0201   abc
      0201   efg     
      0201   mln
      0202   gty
    in <i>FCC ignoer record set= true</i>
    otherwise is not called...
    i try to use split by value & use oneasmany  , not helpfull.
    in message mapping when i checked th field VBELN -> display queue
    i am getting an array   0200
                                     0201
                                     0202  in white fields
    thanks & regards
    Ashutosh Rawat

    <b>Source payload</b>
      <?xml version="1.0" encoding="utf-8" ?>
    - <ns:MT_MATNO_FILE xmlns:ns="urn:abc:xxx">
    - <E2ED20>
      <KZ>E2EDL20</KZ>
      <FIELD1>020</FIELD1>
      <b><VBELN>0083662685</VBELN></b>
      </E2ED20>
    - <E2E24>
      <KZ>E2EDL24</KZ>
      <FIELD2>020</FIELD2>
      <POSNR>900001</POSNR>
      <CHARG>1078629</CHARG>
      <LFIMG>3200</LFIMG>
      <MEINS>PCE</MEINS>
      </E2E24>
    - <E2E24>
      <KZ>E2EDL24</KZ>
      <FIELD2>020</FIELD2>
      <POSNR>900002</POSNR>
      <CHARG>1078630</CHARG>
      <LFIMG>1895</LFIMG>
      <MEINS>PCE</MEINS>
      </E2E24>
    - <E2E24>
      <KZ>E2EDL24</KZ>
      <FIELD2>020</FIELD2>
      <POSNR>900003</POSNR>
      <CHARG>1079145</CHARG>
      <LFIMG>1883</LFIMG>
      <MEINS>PCE</MEINS>
      </E2E24>
    - <E2E24>
      <KZ>E2EDL24</KZ>
      <FIELD2>020</FIELD2>
      <POSNR>900004</POSNR>
      <CHARG>1079146</CHARG>
      <LFIMG>3195</LFIMG>
      <MEINS>PCE</MEINS>
      </E2E24>
    - <E2ED20>
      <KZ>E2EDL20</KZ>
      <FIELD1>020</FIELD1>
    <b> <VBELN>0083662648</VBELN></b>
      </E2ED20>
    - <E2E24>
      <KZ>E2EDL24</KZ>
      <FIELD2>020</FIELD2>
      <POSNR>900011</POSNR>
      <CHARG>1001450</CHARG>
      <LFIMG>2946</LFIMG>
      <MEINS>8PC</MEINS>
      </E2E24>
    - <E2ED20>
      <KZ>E2EDL20</KZ>
      <FIELD1>020</FIELD1>
    <b> <VBELN>0083673936</VBELN></b>   </E2ED20>
    - <E2E24>
      <KZ>E2EDL24</KZ>
      <FIELD2>020</FIELD2>
      <POSNR>900012</POSNR>
      <CHARG>1073953</CHARG>
      <LFIMG>2458</LFIMG>
      <MEINS>PCE</MEINS>
      </E2E24>
      </ns:MT_MATNO_FILE>
    <b>at target what required is</b>
    <item>
    <b><VBELN>0083662685</VBELN></b>
    <POSNR>900001</POSNR>
    </item>
    <item>
    <b><VBELN>0083662685</VBELN></b>
    <POSNR>900002</POSNR>
    </item>
    <item>
    <b><VBELN>0083662685</VBELN></b>
    <POSNR>900003</POSNR>
    </item>
    <item>
    <b><VBELN>0083662685</VBELN></b>
    <POSNR>900004</POSNR>
    </item>
    <item>
    <b><VBELN>0083662648</VBELN></b>
    <POSNR>900011</POSNR>
    </item>
    <item>
    <b><VBELN>0083673936</VBELN></b>
    <POSNR>900012</POSNR>
    </item>
    in Sender FCC
    E2ED20.fieldFixedLengths               7,76
    E2ED20.fieldNames                            KZ,VBELN
    E2ED20.keyFieldValue              E1EDL20
    E2ED20.endSeparator              'nl'
    E2E24.fieldFixedLengths              7,24,13,7,3
    E2E24.keyFieldValue                              E1EDL24
    E2E24.fieldNames                               KZ,POSNR,CHARG,LFIMG,MEINS
    E2E24.endSeparator                              'nl'
    ignoreRecordsetName              true
    source file is already there...
    Message was edited by:
            ashutosh rawat

  • Problem facing in sender file adapter

    Hi XI gurus,
    I am facing a problem in sender file adapter communcation channel
    Is there any restriction in XI that XI picks max of 100 at a time .
    Actaully probolem here is My XI sender file adapter need to pick 2800 file from ftp.
    adapter need to file pick files ranging SAP_OUT_066581_280_INV.xml to SAP_OUT_SZ22TXN066581_2800_INV.xml
    to pick these we have given file name as u201CSAP_OUT_*_INV.xmlu201D when ever given this XI is coming with no messges.
    when ever file name is given as SAP_OUT_SZ22TXN066581_3*_INV.xml it XI has picked file from 300 to 399
    when eve tried with the options to pick all the message
    SAP_OUT_SZ22TXN066581_*_INV.xml  Failed with no messaege
    even atleast tried to pick 1000 mesaanges from 1000 to 1999
    i have given like this
    SAP_OUT_SZ22TXN066581_1*_INV.xml failed with no messages
    while trying with option xi picking file max 100 at a time
    SAP_OUT_SZ22TXN066581_1*_INV.xml
    SAP_OUT_SZ22TXN066581_11*_INV.xml
    SAP_OUT_SZ22TXN066581_12*_INV.xml
    like this I am increaing the number and picking maximum of 100 messages only
    Is there any way to auto mate this or nny file names need to be required
    waiting for your reply

    Check SAP Note 821267 - FAQ: XI 3.0 / PI 7.0/ PI 7.1 File Adapter.
    I guess point 8 might relate to your problem if the FTP adapter timeout occurs.
    check the note 849089 as well.
    Also check point 13 and 26.
    Gaurav Jain
    Points if answer is useful
    Edited by: Gaurav Jain on Jun 6, 2008 4:20 PM

  • Problem in Sender File Adapter using FCC with Variable structure

    Hi Experts,
    Hi Experts,
    I have facing an issues while using FCC in Sender File adapter. Below are the configs for the same:-
    Recordset structure required is ==HEADER,1,DATA,*,TRAILER,1
    Recordset per message == *
    Key Field Name == Key
    (Sorry i dont know how to insert screen shot here..pls tell me how can i insert screen shots here on sdn)
    HEADER.fieldSeparator           ,
    HEADER.endSeparator           u2018nlu2019
    HEADER.fieldNames               Key,x,y,zu2026
    HEADER.keyFieldValue          1
    HEADER.keyFieldInStructure      ignore
    HEADER.fieldContentFormatting     trim
    HEADER.additionalLastFields     ignore
    HEADER.missingLastFields     ignore
    DATA.fieldSeparator
    DATA.endSeparator
    DATA.fieldNames
    DATA.keyFieldValue
    DATA.keyFieldInStructure
    DATA.fieldContentFormatting
    DATA.additionalLastFields
    DATA.missingLastFields
    Using same variables for Trailer record as well.
    Source CSV file which i am picking:-
    ADSE ,RASD,replan  Contact ,2  0080509 0 8:43:25   ,        
    EMPL ,0011111,  S Top Up ,20080401  ,20080430  ,sdf  ,                          00000000431250  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:07:35,
    EMPL ,0222222,  r Cash Award ,20070701  ,20070703  ,ded  ,                          00000000023509  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:09:31,
    EMPL ,0233333,   Cash Award ,20070801  ,20070831  ,df  ,                          00000000044057  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:10:56,
    EMPL ,0244444,   Cash Award ,20080101  ,20080111  ,sf  ,                          00000000026717  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:08:29,
    BTRL ,   5140, 
    When i tested the scenario and monitored it using MDT in CC monitoring tool its giving me below mentioned error.
    The XML page cannot be displayed
    Cannot view XML input using style sheet. Please correct the error and then click the Refresh button, or try again later.
    XML document must have a top level element. Error processing resource 'http://myurlname/mdt/me...
    However if i change the occurence of DATA as some specific value for eg 4 instead of * it works fine.
    Kindly help me in solving this problem.
    Thanks,
    Aditya Verma

    Hi Madan,
    Thanks a lot for giving me the way to this. But when i tested this with the below file its giving me the same error. Please let me know if i need to do any changes to the parameters mentioned above:-
    ADSE ,ASDA,Sha  replan Fr ont Feed Contact ,2  0080509 0 8:43:25   ,        
    EMPL ,0011111,   Cash Top Up ,20080401  ,20080430  ,TPV  ,                          00000000431250  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:07:35,
    EMPL ,0222222,   r Cash Award ,20070701  ,20070703  ,TPV  ,                          00000000023509  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:09:31,
    EMPL ,0233333,  r Cash Award ,20070801  ,20070831  ,TPV  ,                          00000000044057  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:10:56,
    EMPL ,0244444,   Cash Award ,20080101  ,20080111  ,TPV  ,                          00000000026717  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:08:29,
    EMPL ,0255555,   Cash Award ,20080301  ,20080320  ,TPV  ,                          00000000027870  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:08:25,
    EMPL ,0266666,   Cash Award ,20071001  ,20071020  ,TPV  ,                          00000000020681  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:09:31,
    EMPL ,0877777,   Cash Top Up ,20080401  ,20080430  ,TPV  ,                          00000000036000  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:07:05,
    EMPL ,0888888,   Leaver Cash Award ,20071201  ,20071231  ,TPV  ,                          00000000157200  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:11:29,
    EMPL ,0899999,  S Leaver Cash Award ,20080301  ,20080331  ,TPV  ,                          00000000153530  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:07:42,
    EMPL ,0800000,  S Leaver Cash Award ,20070701  ,20070731  ,TPV  ,                          00000000012234  ,2007                                    ,  ,  ,  ,  ,  ,20080414  18:08:34,
    BTRL ,   5140,
    This the original csv file which i'll get in live. Kindly suggest as ur solution worked with other file but not working with this scv file.
    Thanks a lot,
    Aditya.

  • Problem in sender file adapter

    Hi all,
      I have a sender file adapter using ftp with processing mode delete. But my input file is not getting deleted. In RWB, the adapter satus is green with msg processed sucessfully. I tried with a file name that is not available in the ftp folder, but still the adapter status is green with msg processed succesfully.
    Help me debug this error.
    Regards,
    Jai Shankar.

    Are you using Content conversion ?
    If adapter monitoring is green, and shows processed successfully, then if you have any errors , you can see in the RWB->Message Monitoring->Audit Log (Message display Tool).
    If there is no error, then try to do the cache refresh as I told. Ask Admin help for that. Restarting a Adapter engine may help you here/
    Regards,
    moorthy

  • File Content Conversion Problem: Sender File Adapter

    Hi All,
    In Sender File Adapter, how to spilt the single line into different lines using + as a separator. Plz see below my source file.
    #SMESS=IV01:672633SAP:676968:::NL51:02:11+
    COPS=678713:676968:070416:IV01'3:11IVFR=678713:PDA and'IND 2'9206 AD'Dtn'INIVDA=070416IVNR=6264008195:676968add1
    #EMESS=0+
    In above txt file there are 3 lines.
    1st line starts with #SMESS
    2nd line starts with COPS 
    3rd line starts with #EMESS.
    In 2nd line, if u observe there are 3 lines separating by +. My task is, I have to spilt the 2nd line into 3 lines using + separator.
    I already used the xx.endSeparator as '+' to spilt the line but it is not working....
    Could anyone help me how to do this. This is very urgent
    Thnx,
    Kumar.

    Hi Shankar,
    1) My Expected XML Structure:
      <?xml version="1.0" encoding="utf-8" ?>
    - <ns:MT_IV01 xmlns:ns="http://ms.com/dev/ms">
    - <Recordset>
    - <DT_SMESS>
      <D_9901>IV01</D_9901>
      <D_9902>672633SAP</D_9902>
      <D_9903>676968</D_9903>
      <D_9904 />
      <D_9905 />
      <D_9906>NL51</D_9906>
      <D_9907>02</D_9907>
      <D_9908>11</D_9908>
      </DT_SMESS>
    - <DT_COPS_2>
      <D_C022>678713</D_C022>
      <D_C023>676968</D_C023>
      <D_C008>070416</D_C008>
      <D_C111>IV01'3</D_C111>
      <D_H559>11</D_H559>
      </DT_COPS_2>
    - <DT_IVFR_2>
      <D_C024>678714</D_C024>
      <D_D333>PDA and'IND 2'9206 AD'Dtn'IN+</D_D333>
      </DT_IVFR_2>
    - <DT_IVDA_2>
      <D_D365>070416</D_D365>
      </DT_IVDA_2>
    - <DT_IVNR_2>
      <D_D189>6264008195</D_D189>
      <D_H364>676968add1</D_H364>
      </DT_IVNR_2>
    - <DT_EMESS>
      <D_D9901_1>0</D_D9901_1>
      </DT_EMESS>
      </Recordset>
      </ns:MT_IV01>
    2) I am not getting any error even if I use key Fields or Not becoz in the RecordSet Structure I mentioned DataType, 1 instead of DataType, *.
    3) FCC Parameters:
    Document Name: MT_IV01
    Document Namespace: http://ms.com/dev/ms
    Recordset Structure: DT_SMESS,1,DT_COPS_2,1,DT_IVFR_2,1,DT_IVDA_2,1,DT_IVNR_2,1,DT_EMESS,1
    Recordset Sequence: Ascending
    Key Field-type : String (Case-sensitive)
    4) Error:
    Conversion of file content to XML failed at position 0: java.lang.Exception: ERROR converting document line no. 2 according to structure 'DT_COPS_2':java.lang.Exception: ERROR in configuration: more elements in file csv structure than field names specified!

  • Advance select for source file in Sender File Adapter

    Hi
    I am trying to utilise the parameter 'Advance Selection for source file' on a sender file adapter to pick the file from multiple folders
    My problem is that this parameter that is listed on the SAP help is not getting in File accessing Parameters.
    I am running PI 7.02 (NW702_07_Rel)
    Service pack 07
    Has anyone come across this before?
    any suggestions on how to do this?

    Hi,
    In PI7.0 the property exists. I have used it previously. I think SP was 13.
    Regards,
    Nutan
    Edited by: nutan champia on Nov 24, 2011 10:42 AM

  • Archive file with errors in sender file adapter not working! please help!

    Hi Experts,
       I have a file to RFC scenario. the input is a XML file. I have setup the flag in sender file adapter channel for archiving the input files with errors. But it is not working.
    For testing I have used an invalid xML file for example without the main XML tag. I have also tested with a MSWORD file saved with.xml extension. But in both the cases the files are not getting archived.
    My archive location permissions are fine and in fact normal archive operation is happening. That is, if I select the processing mode as "Archive" and gave the Archive directory then files are getting archived. The problem is only with the "Archive faulty source files" option.
    What am I missing? DO I need to do some more configurations?
    What are the prerequisites if any for this option?
    How to test this?
    Please help me! I will be greatfull to you all!
    Thanks & Regards
    Gopal

    and go thru this links
    Creating a Single Archive of the Version Files
    http://help.sap.com/saphelp_nw04/helpdata/en/79/1e7aecc315004fb4966d1548447675/frameset.htm
    http://help.sap.com/saphelp_nw04/helpdata/en/31/8aed3ea86d3d67e10000000a114084/frameset.htm
    Note: reward points if solution found helpfull
    Regards
    Chandrakanth.k

  • Unzip file using PayloadZipBean in Sender FILE adapter

    I am trying to unzip a flat file in Sender FILE adapter using PayloadZipBean.
    I am getting mapping error. The problem is File adapter is reading data without unzipping. I am getting weird characters/data, so mapping error.
    I searched all the blogs/ forum threads and help.sap.com, everywhere the focus is on zipping, not unzipping.
    the file I have is with .gz extension, but I tried with .zip extension also.
    Please help in resolving this issue.
    Edited by: Gopal Janagama on May 2, 2008 11:42 PM

    Gopal,
    GZIP and ZIP format are slightly different, as stated here :
    "GZIP compresses only one file and does not have a header. ZIP contains header information about what files are contained in the file."
    So I'm not sure the PayloadZipBean supports GZIP format ... Try to ungzip and then zip its content and see if the bean works for it
    Rgds
    Chris

  • Recordset per message in Sender File Adapter

    Hi Friends
    I have configured a sender file adapter to pick up *.txt files from a specific path, Since the file is having thousands of records it is failing to process the file at  PI level . In order to avoid the problem I have kept Recordset Set Per Message as 10 , but still PI is processing all the records into a single message. Please help me in troubleshooting it.
    Regards
    Suman.

    Hi Suman,
      Go thru these threads for troubleshooting...
    Massive file
    Processing huge file loads through XI
    Processing of huge no of Inbound xml files
    Bottleneck in Large file processing
    How to process large data files in XI  ?  100 MB files ?
    Regds,
    Pinangshuk.

  • Zero size files in Sender File Adapter

    Hello!
    I have the problem with my Sender File Adapter (ftp).
    Sometimes in ftp directory there are empty files or messages with a zero-sized payload.
    This situation cause an error and Adapter "sleep" until I save-active it in a configuration. (before I removed the 0-size file...).
    Any suggestion?
    Thanks
    Alessandro

    Hi ,
    What the note states is that if your Sender File adapter picks up and empty file, then it would not trigger any message at all.
    So, if what that note says is correct, then I guess for the empty file, the adapter would not ve passed any message to the integration engine.
    Is there any entry in SXMB_MONI? If yes, then it means some message is actaully being passed by the adapter engine to the integration engine which shouldnt have happened at all.
    What does the error message in the File Adapter state?
    Regards,
    Bhavesh

Maybe you are looking for

  • Link vendor payments to PO

    Hi My requirement is that  i want to link payments ( vendor ) to PO i.e how much payment has been made to particular vendor for a particular vendor . I have placed several orders to a single vendor for the supply of different material. In my scenerai

  • Flashing screen when connected to computer

    My ipod classic recently started acting up. The screen is black and non-responsive. When I connect it to the computer with the usb cable it flashes on and off with the apple logo screen. The computer does not even recognize that anything is plugged i

  • How to see the timeline when animating

    My timeline does not appear regardless of what I do. How come?

  • Which data structure?

    Hi there... Could you let me know what is the most efficient data structure to use (in terms of storage and access) if I have to store around 1 million <key,value> pairs? Thanx :) Tariq

  • Why jarsigner does not work

    I was trying to use jarsigner tool. First I create a keystore a.store with a key key1. Then I create a .jar file and sign the .jar file using the key1 in a.store. Finally I create another keystore b.store with another key key2. To my suprise, if I ru