Sending alerts or mails to SBWP using infotype 0019
Sending alerts or mails to SBWP using infotype 0019
These threads might be useful.
[Reminder Message;
[Re: How to configur Infotype 0019 (monitoring of task);
Similar Messages
-
Cannot receive/send emails via Mail on Mac using 10.6.8, keeps asking for password, very frustrating. Any ideas please? Regards
One more time, iCloud mail accounts are .me, .mac and .icloud. New ones are only .icloud.
iCloud mail is a standard Imap account that can be used with any mail client in existence. But You are talking about the ability to automatically setup an iCloud account in mail, which did not exist until 10.7.2.
You can use password or token authentification with iCloud mail (in Mail) it is your choice.
Set the account manually, set it as Imap, use imap.mail.me.com (no P number) for the incoming email and smtp.mail.me.com as the outgoing server.
The full settings (ports and security) are here. Use them and it will work, regardless of domain (mac, me and icloud addresses all use the same settings.
IMAP (Incoming Mail Server) information:
Server name: imap.mail.me.com
SSL Required: Yes
Port: 993
Username: [email protected] (use your @me.com address from your iCloud account)
Password: Your iCloud password
SMTP (outgoing mail server) information:
Server name: smtp.mail.me.com
SSL Required: Yes
Port: 587
SMTP Authentication Required: Yes
Username: [email protected] (use your @me.com address from your iCloud account)
Password: Your iCloud password
Note: If you receive errors using SSL, try using TLS instead. SSL is required for both IMAP and SMTP connection with iCloud. POP is not supported by iCloud.
For more information on how to use this information with your email application, consult your application's documentation. -
Send Alerts(e-mail) for errors in SXMB_MONI(message mapping exceptions)
Good afternoon !
I´m configuring SAP Netweaver PI 7.0(SP13) to use Alert Framework to send Alerts when errors occurs in the interfaces processing.
I just achieved configure to send alerts when errors ocurrs in the Adapter Framework but, I can´t configure correctly to send alerts when errors ocurred only in SXMB_MONI(for example, message mapping exception in asyncronous interface).
I just followed the instructions at Michal Krawczyk
weblog(/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--step-by-step) and, initially, this was not sufficient to start to send alert when errors occurs only on SXMB_MONI, so, I researched and found some configurations to do in CCMS(started from here: http://help.sap.com/saphelp_nw70/helpdata/en/e3/bf3b7a8ccb8040b638ff732c551aeb/content.htm), jobs to start events collectors, etc, and after this, I could see a mail for an message mapping exception. BUT, this message, sent from CCMS to ALM, doesn´t carry out all the message parameters, like message Id, sender(service, interface), receiver(service, interface), that is very important to help to find the message with errors to be solved.
There is somebody here that already done the Alert configuration to send messages for errors found only in SXMB_MONI(Monitor for processed XML Messages) ?
There is a better way to achieve this ?
Thank you for your attention,
Wilson Rodrigo dos Santos
SAP Netweaver XI/PI ConsultantHi
Go through these links and follow it.
ALERTS CONFIG AND STUFF
http://help.sap.com/saphelp_nw04/helpdata/en/80/942f3ffed33d67e10000000a114084/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/49/cbfb40f17af66fe10000000a1550b0/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/49/cbfb40f17af66fe10000000a1550b0/frameset.htm
XI: Alerts - Step by step
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--step-by-step
http://help.sap.com/saphelp_nw04s/helpdata/en/d0/d4b54020c6792ae10000000a155106/frameset.htm
Triggering by Calling a Function Module Directly.
/people/bhavesh.kantilal/blog/2006/07/25/triggering-xi-alerts-from-a-user-defined-function
Alerts with variables from the messages payload (XI) u2013 UPDATED
/people/michal.krawczyk2/blog/2005/03/13/alerts-with-variables-from-the-messages-payload-xi--updated
Simple Steps to Get Descriptive Alerts from BPM in XI
/people/community.user/blog/2006/10/16/simple-steps-to-get-descriptive-alerts-from-bpm-in-xi
Triggering XI Alerts from a User Defined Function
/people/bhavesh.kantilal/blog/2006/07/25/triggering-xi-alerts-from-a-user-defined-function
Throwing Smart Exceptions in XI Graphical Mapping
/people/alessandro.guarneri/blog/2006/01/26/throwing-smart-exceptions-in-xi-graphical-mapping
/people/sukumar.natarajan/blog/2007/01/07/how-to-raise-alerts-from-abap-proxy
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--troubleshooting-guide
/people/sravya.talanki2/blog/2006/11/22/error-handling-framework-xiout-of-the-box-episode-1
/people/ginger.gatling/blog/2005/06/16/integrating-alerts-into-uwl--its-no-problem
/people/aravindh.prasanna/blog/2006/02/20/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part-3
/people/aravindh.prasanna/blog/2005/12/24/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part-2
/people/aravindh.prasanna/blog/2005/12/23/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part--1
http://help.sap.com/saphelp_nw2004s/helpdata/en/56/d5b54020c6792ae10000000a155106/content.ht
http://help.sap.com/saphelp_nw04/helpdata/en/2c/abb2e7ff6311d194c000a0c93033f7/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/80/942f3ffed33d67e10000000a114084/frameset.htm
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--step-by-step
check this links.
https://www.sdn.sap.com/irj/sdn/forums
Trouble shooting Alert configuration:
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--troubleshooting-guide
/people/michal.krawczyk2/blog/2005/06/28/xipi-faq-frequently-asked-questions
Alert Inbox
http://help.sap.com/saphelp_nw04/helpdata/en/80/942f3ffed33d67e10000000a114084/frameset.htm
Alert Notification Step-by-Step
http://help.sap.com/saphelp_nw04/helpdata/en/49/cbfb40f17af66fe10000000a1550b0/frameset.htm
Defining Alert Classifications
http://help.sap.com/saphelp_nw04/helpdata/en/49/cbfb40f17af66fe10000000a1550b0/frameset.htm
Triggering Alerts
http://help.sap.com/saphelp_nw04/helpdata/en/49/cbfb40f17af66fe10000000a1550b0/frameset.htm
Setting up alerts
Setting up alerts in RZ20
Alert Management
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/e04141e8-0f11-2a10-adaa-9d97b062c2df
Alert Notification
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/90f449a8-a6db-2910-a386-d2b5999f5751
/people/matt.kangas/blog/2006/06/27/personalized-alert-delivery
Thanks
Saiyog -
Hi to all,
i have a require meant that i want give alert to mail if some event occur ..
by using exception i am rising massage but i want send that massage to particular mail id how can i please glide me.....
Thanks & Regards,
Sridhar.http://download.oracle.com/docs/cd/B19306_01/appdev.102/b14258/u_mail.htm#i1001258
-
Hi All,
I have created the Alert category, Alert rules and I have added my name in SU01, but still iam not able to get the mails when any error occures in the scenario IDOC to File.
If aimk missing any setting that need to be done please let me know.
Thanks and Regrads,
chinnahi ,
You can adopt Simple Approach,
1. Put one more receiver service in your Receiver determination step along with the current File Service.
2. in the new service send the mail using the standard XI mail adapter to emial receipents.
Just refer
a) creating alert categories : Click [Link1|http://help.sap.com/saphelp_nw04/helpdata/en/d0/d4b54020c6792ae10000000a155106/content.htm]
b)creating alert rules :Click [Link2|http://help.sap.com/saphelp_nw04/helpdata/en/56/d5b54020c6792ae10000000a155106/content.htm]
-Thanks & Regards
Saurabh Goel -
Trouble sending some e-mails with iPhone using Yahoo account
Hi Everyone,
I hope someone can help me with this problem. It seems that about 30% of the e-mails I compose directly from my iPhone never reach their destination. When I hit "send" they simply disappear from the screen with no record of them in yahoo's "sent" folder.
It is getting very frustrating, especially after I spend 15 minutes or so tapping out an e-mail letter by letter (I am slow).
Is anyone else having this problem? If so, how did you solve it??
I am a bit of a neophyte so if you could walk through a solution, I would be most appreciative.
Thank You!This is a know issue with Yahoo! Email on the iPhone. When sending email, sometimes it will say it has been sent, while it really has not (and it will not show up in the sent folder).
It has been discussed quite a bit in the forums, so a search will turn up a lot of discussion, but no solid solution. Some say Yahoo is working on a fix, other that Apple is.
The most common solution (which is usually temporary), is to either reboot your phone, and/or delete and reinstall your Yahoo! Mail account on your phone. -
My i-pad 1 wont send or receive mail since i used virgin trains wi fi is there a fix please?
I can not connect to my internet provider for mail.Is there a fix please
I agree with Rudegar and I would simply emphasize that you double check your username and password and make sure that they are correct. You may have entered a capital letter or lower case letter that was incorrect.
Your e-mail provider must have FAQ or help site available for mail set up on the iPad. Look there for help. -
Sending Alert Messages to File System
Hi,
I am trying to implement a scenario in PI which automatically processes alert message generated by the Alert Framework (the messages are processed in a message mapping). Therefore I am sending alerts via mail and receive these mails afterwards with an integration scenario PI. As this does not work if the mail server is offline I am searching for a possibility to send alert messages directly to the file system. Is there a way to do this? Or do you have any other suggestions how I could handle this problem?
Regards,
ChristianHI Christian,
The other option to get the alerts is to regster for SMS alerts to your mibile, in addition to the mail alerts.
Regards
Venkat -
I want my old Mozilla Firefox back because ever since I agreed to try the new Firefox, I've had nothing but problems every single time I try to send an e-mail. What used to be easy and quick, now is difficult and takes an inordinate amount of time; sending it over and over, and telling the message that tells me something like a page is not responding, to send it again or quit; and I have to do this many times over to get it to send a text. That has never happened before. I will never agree to a newer version again. Just please give me back my old Mozilla Firefox.
Beginning with Firefox 4, Macs must have an Intel x86 processor (which you do NOT have; yours is a PPC Mac) '''''<u>and</u>''''' OSX 10.5 or higher
*System Requirements: [https://www.mozilla.org/en-US/firefox/4.0/system-requirements/index.html Firefox 4] [https://www.mozilla.org/en-US/firefox/5.0/system-requirements/index.html Firefox 5] [https://www.mozilla.org/en-US/firefox/6.0/system-requirements/index.html Firefox 6] [https://www.mozilla.org/en-US/firefox/7.0/system-requirements/index.html Firefox 7] [https://www.mozilla.org/en-US/firefox/8.0/system-requirements/index.html Firefox 8]
The good news is that Firefox 3.6.24 still supports OSX 10.4 and Macs with the PPC Mac architecture. The bad news is that support for the Firefox 3.6.x series is likely to end in the first quarter of 2012.
*System requirements: [https://www.mozilla.org/en-US/firefox/3.6/system-requirements/index.html Firefox 3.6.x]
*Download Firefox 3.6.24: https://www.mozilla.org/en-US/firefox/all-older.html
*Also see --> http://support.mozilla.com/en-US/kb/Installing+Firefox+on+Mac
You can try the third-party product '''''TenFourFox''''' that supports PPC Macs. Firefox 8 version of '''''TenFourFox''''' is available. The product is based on Firefox released versions. All support is provided by the developer, not by this site:
*Home page: http://www.floodgap.com/software/tenfourfox/
*Developer's blog: http://tenfourfox.blogspot.com/
*VERY IMPORTANT; read this carefully: https://code.google.com/p/tenfourfox/wiki/PluginsNoLongerSupported
'''If this reply solves your problem, please click "Solved It" next to this reply when <u>signed-in</u> to the forum.''' -
How send attachments to mail using oracle alerts
Hi All,
I am working on Oracle Alerts in oracle applications. how to send attachment to mail.
Thanks in Advance,
Reddy.
Edited by: user9540785 on Mar 22, 2009 4:48 AMAs a workaround, you can kick start a custom workflow in actions rather than sending mail. In that custom workflow you can send attachments as part of the notification to the respective recipients.
Thanks
Nagamohan -
This is regarding CBMA in single stack SAP PI 7.3.1. I have set up the alert mail using default java mail client.I do receive the alerts via mail. But my requirement is to direct all the alert mails to Business workplace inbox in ECC.
So I need to set up PI to redirect mails to ECC Business workplace user inbox (sbwp). From here rules are set up & routed per distribution list.
Please guide me how I can achieve this requirement.Hi,
yes, it is a little bit different. This is the issue.....
But I am not sure if your links will help:
1) /people/william.li/blog/2008/02/13/sap-pi-71-mapping-enhancements-series-using-graphical-variable
is about a different solution. I do not need to count the number of lines of the source message.
And the second variable is about concat line by line from unbound node to unbound node.
My issue is:
Souce:
Message line (0...unbound) ! ! ! ! ! ! ! !
. ResultLine (1..1)
Mapping:
=> ResultLine1
ResultLine2
ResultLine........ => into UDF to an element (1..1) in one mapping operation.
So that all "ResultLine"s are included.
The result is explained in the given link for Mail attachment with UDF.
So I am not sure how to use this thread for my issue.
In the comments of that blog Christoph Gerber writes that the new variable feature can only handle single values.
So it is not suitable for my purposes as I have a list of values here that needs to be moved into the target message field.
2) http://wiki.sdn.sap.com/wiki/display/Java/UsingEditJavaSectioninMessageMapping
shows where to find the button "Java section" which is not available here in 7.1
3) /people/sap.user72/blog/2005/10/01/xi-new-features-in-sp14
too is about the nice little button for Java Section that is no longer existing on PI 7.1 screen for mappings.
So my issue is: How to replace the Java section function with global variables in PI 7.1?
Best regards
Dirk -
How to configure ML Server to send Alert Notifications by mail?
Is it possible to configure Mountain Lion Server to send out Alert notification by e-mail without enabling full Mail services?
I don't want to run the Mail service on the Server. I'm quite happy with my ISP's mail service. Besides, I have a dynamic public IP address, hence no rDNS entry (so I couldn't run Mail if I wanted to). And I don't have the expertise to configure and maintain the Mail service. But I would like to get the Server to send me any important alert notifications by e-mail.
I have access to an authenticated SMTP server I can use to relay the outbound alert notification emails. But I don't know how to coerce the alert service into using it. Is it possible to do so, or does one need the full-blown Mail service to be configured (with both dovecot and postfix running) in order to get Alerts to be e-mailed?
Thanks for any help.@MrHoffman,
Thanks for the pointers and suggestions.
The config for my ISP's SMTP server is correct. I specified the port (:465), and double-checked userid/password. It's the same as used by all our e-mail clients (a half-dozen or so on various Macs, iPhones, iPads, Linux boxes), all of which work fine from my LAN.
As for DNS, it seems OK. (I am indebted to you for the excellent series of articles on servers and networking at http://labs.hoffmanlabs.com/node/1705 )
The changeip command reports:
The names match. There is nothing to change.
dirserv:success = "success"
However, I should point out that I do not have the DNS service enabled on ML Server. I already have a local DNS running on my gateway router. (it's an instance of the dnsmasq process that is part of Tomato firmware). It has local names defined for all the servers and hosts on my LAN, and provides rDNS for them as well.
However, what I haven't done is enabled the Mail service. You've (slightly) misunderstood the core of my plan. My intent is not simply to secure the local mail server against remote access. I don't want either remote or local users from accessing the mail server. I don't want it listening for POP or IMAP connections from anywhere (on my LAN or remotely). I don't want it receiving inbound mail from anywhere. I don't want it relaying outbound mail for any client on my LAN. All I want the ML Server to be able to do is to send me alerts (by e-mail) when it's in need of attention. Other appliances on my LAN (eg. a NetgearReadyNAS) can send me e-mails when they are unhappy, and I hope I can coerce the ML Server to do the same.
I know I don't have the expertise to operate and maintain my own mail server, and I'm quite happy with the mail service provided by my existing network service provider. Plus, I'm behind a cable modem with a dynamic IP address, so I'm unable to establish my own rDNS record (which I understand is required to handle inbound mail).
It looks like the next step is to turn on the Mail service. But I'm sure it's going to be unhappy since there's no MX record set-up. I was hoping there was a way that ML Server could simply send out its own outbound alerts (using my ISP's SMTP relay) without having the incoming part of the mail service active. But perhaps Apple didn't anticipate that sort of configuration. -
Using Function module SALRT_CREATE_API i am sending alerts ..
Hi gurus,
i am using the Function Module SALRT_CREATE_API to send alerts.
i run the same F.M. in se37 with same input alert id is generated and in SOST i checked them.
but after using the F. M in program , alert id is generated, but in SOST i didn't find anything.
using alert id where i have to check those mails , kindly suggest me ..
Thanks & Regrads
kalyan.Hi,
Check the bellow thread as per your requirement.
How to use function module SALRT_CREATE_API to trigger alert in XI?
Regards,
Goutam Kolluru. -
Sql Express Edition R2 can we send alert mail
Hi There,
We are using SQL 2008 Express edition R2. Can we send alert mail using sql services in SQL 2008 Express edition R2Hello,
Database Mail is not supported in the Express Edition; see
Features Supported by the Editions of SQL Server 2012
Olaf Helper
[ Blog] [ Xing] [ MVP] -
XI Alert cannot send through external mail id ?
Hi,
I have configured XI Alert to monitoring Adapter Engine, The Alert is triggert and i can see in my Alert In_box in RWB.
But then how to configure the alert send using external id
I have configured SCOT as well, but i can't see anything from SOST ?
Please advise any other possibility than i need to check ?
Thank You in Advance.
FL.
Edited by: Fernad Lesmana on May 1, 2011 6:33 AMHi Fernad,
Assign the mail id of the recipeint of the alert in Su01
Go to the alert inbox of the recipient , in the option / link --> personalization --> Time Independent Delivery --> select EMAIL.
If scot is configured for every alert, the mail will be forwarder to the recipient mail id allocated in SU01
also try out this,
Goto SCOT. Inside node int (Internet), u will find another node*/SMTP.
Try to Configure the SMTP node. Goto Node SMTP and select Node in use checkbox.
Now, in SMTP Connection -->Mail Host <specify hostname of mailserver> and Mail Port <Specify the mail port, most probably 25> and Codepage <You can select code page >
Internet will be automatically selected, double click on set beside internet
in address area specify '*' so that anyone can be sent mail
schedule backgroud job for mails to go out of SMTP Plugin of ICF.
chk the link for alert configuration :-
http://help.sap.com/saphelp_nw04/helpdata/en/b2/de0741375cf16fe10000000a1550b0/frameset.htm
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--step-by-step
Regards
rohit
Maybe you are looking for
-
Satellite A200 - error message on Bule Screen when I'm doing somthing hard
I have a Laptop the details is as below *Model Name: Satellite A200-11C* *Model No: PSAE0E-00X00KAR* I have setup Windows XP (Service Pack 2) on it. After installation, when I try to Play Video file or Scan for Virus or working long it shows an messa
-
Open a PDF file using PDF reader
Hi All, How to open a dynamique adresse of pdf files with adobe reader and not with the browser using URLLoader Thanks, Amine
-
Can't create photo book in iPhoto 9.6 (910.29)
I am trying to create a photo book in iPhoto. I have created books in the past but well over a year ago so I don't know when the issue could have started. When I click on create, seemly nothing happens however when I quit iPhoto and start it up agai
-
Does iTunes make a compatible version for windows '98? where can I find it?
-
Dear experts, What is the significance of maintaining bank key in vendor master? Can multiple bank codes/numbers be assigned against one bank key or do I have to create as many bank keys as there are bank codes/numbers? What is the corelation betwee