Sendmail command on Content Switch.

I want to get e-mail alert's from my content switch. I was going to use the logging sendmail "e-mail address" "IP of SMTP host" command by what IP address will the switch use for outgoing mail use?

The second parameter "IP of SMTP host" is the address of an email server that will accept the SMTP connection. The subject of the email includes the management port's IP address. I don't use the management port so I set it something that helps me to identify the specific switch.

Similar Messages

CSM-Content Switching Module

Hi All,
How to shutdown Content Switching Module in Cat 6500 switches ? I want to shutdown only CSM-Module without disturbing Chassis.
Can anyone please send me the command on that ?
Highly appreciate your valuable reply.
Thanks,

Hi,
Assuming you are using IOS, you can power-down a module in a 6500 chassis using the command
"no power enable module " in global config mode where is the slot number of the CSM.
If you are using CatOS then the command would be:
"set module power down "
The CSM should be hot-swappable so you should be able to just pull it out of the chassis, but I think that is a bit vicious if you only want to shut it down.
HTH
Cathy

How can I encrypt my data links between switch uplink ports ? I'm unable to use "cts Manual" command in C3560X switch.suggest me

How can I encrypt my data uplinks between switch trunk ports ? I'm unable to use "cts Manual" command in C3560X switch.suggest me as I want to encrypt my switch-to-switch link with Cisco TrustSec.

Hi
Login to switch & go to interface..
There you can give tags.. (ISL & DONT1Q)
Command switch-port mode trunk
Switch-port trunk encapsulation ssl or dot1Q

How to add the IP address helper command to the switch

Hi
I am trouble shooting a SF 200-48P and I am a bit lost without a CLI not used to the GUI. What I need to know is how to add the IP address helper command to the switch?
I have a number of IP phones which are not getting an IP address from DHCP (PCs which are diasy chained off the phones are all working correctly). On the higher end switches I would have added the IP address helper command to the VLAN and that would have sorted it. However I can't seem to figure out how to do this on the small business switch.
Thanks
Lorne

Thanks Rizwan. I was banging my head wishing they weren't small business switches as I felt lost without the command line!
Lorne Gallagher | McCann FitzGerald Solicitors | Riverside One, Sir John Rogerson's Quay, Dublin 2, Ireland | DDI +353 1 607 1726 | Fax +353 1 829 0010 | www.mccannfitzgerald.ie
Ireland Law Firm of the Year 2011 | Chambers Europe
Ireland Law Firm of the Year 2011 | International Financial Law Review

CRASH! Safari 2.0.3 & Mail 2.0.7 apple-i command "Mail Contents of Page"

In Safari [versions above] the apple-I command "Mail contents of this page" crashes my entire computer every time. Everything freezes. Complete crash, requires emergency restart with power button. Even option-apple-esc will not bring up the "force quit" options. When this happens, Activity Monitor indicates that 100% of the CPU effort suddenly is taken up by Mail.app
Mac OS X version is: 10.4.6 with all updates installed.
The shfit-option-I "mail link to this page" works perfectly.
It happens on any web page visited.
Is anyone else having this problem?
PowerBook G4 Mac OS X (10.4.6)
PowerBook G4 Mac OS X (10.4.1)
PowerBook G4 Mac OS X (10.4.1)

I installed Tiger as an upgrade from Panther 10.3.9.
I would have responded earlier, but I just ran the unix maintenance scripts (MacJanitor 1.3) and Repaired permissions, and rebooted just to make sure this wasn't the issue. I tried it again, and once again had issues. It took five to ten minutes, but it finally launched Mail and did what it should. In the meantime, I actually saw Mac OS X come to a standstill (menu bar clock seconds stopped ticking) for the first time ever. I tried again after Mail was open, and it worked instantly. Next to try some preference dumping.....

Specs for 11500 Content Switches

I am looking for more specs on the 11500 series content switches. Specs such as http connections per second, tcp connections total.

Ted,
The following link:
http://www.cisco.com/en/US/products/hw/contnetw/ps792/prod_bulletin09186a008017dc5d.html
states that "A Cisco CSS 11506 can now achieve more than 45,000 TCP connections per second and, if configured with 4 SSL modules, can attain over 4000 SSL transactions per second."
Is that what you are looking for?
Keep in mind that performance will be slower with layer 5 rules than strictly layet 4 rules.
-Steve

Tabs and content switcher

We're using a lower version of adf (10g) and using uix. Anybody here who has a sample of using tabs with content switcher.
Basically I want to have 2 fixed tabs and when I click a tab, the content is shown in the same page. The content of the
page basically consists of just read-only VO table..
Appreciate any help.
Thanks!

Hi SarahShay,
You could use JavaScript client object model to retrieve blog posts. You could use the getItemById(id) function to return a single item, or use the getItems(query) function to return multiple items.
An official documentation:
https://msdn.microsoft.com/en-us/library/office/hh185007(v=office.14).aspx
A similar post:
http://blogs.msdn.com/b/sharepointdev/archive/2011/07/19/working-with-the-ecmascript-client-object-model-jsom-in-sharepoint-2010-part-3-nikhil-sachdeva.aspx
Best Regards,
Dean Wang
TechNet Community Support
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

What's "SAVE" configuration command for Cisco switch/ router?

What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well,
but so long, any other command that easy to remenber?

What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well, but so long,
any other command that easy to remenber?
yes, here: Switch#write,and want to know more about the Cisco switch, please visit:http://www.3anetwork.com/cisco-switches-price_c1

SAP talking to another sever that is load balancing (with a content switch)

Hi All,
We are retrieving some files from an external server in SAP from an ABAP report using HTTP. The external server is also load balacing on 3 servers. There is a content server (proxy server) which carries the sap request to one of the three servers.
We are able to retrieve the files when we directly connect to one of the three server, However when SAP calls the content server, we get a HTTP code error -404 Status - Not found. Here is the excerpt of code where this error is coming up-
CALL METHOD w_http_client->response->get_status
IMPORTING
code = lv_http_code
reason = lv_status_text.
The external server (content server) is supposed to be transparent and thus SAP should be able to connect. But this does not happen.
Any ideas?
Thanks in advance! Liz

We are now connecting SAP directly one server since we could not connect to the content switch.
Thanks, Liz

Multiple context on Cisco Content Switching

Hi Everyone
I had new case with Cisco Content Switching design. The current network has two Cisco Content Module (CSM) and each of them response for switching content on one Vlan.
Now i want to reconfigure it, to meet the redundancy requirement. But i don't know Cisco Content Module have same idea of design with ACE on Route Mode.
I want configure CSM with two or more vlan pair in routed mode and it can HA between each other.
Thanks
Phai La Quy

Hi Phai,
Yes you can configure CSM in routed mode with clients in one VLAN and server in another. Pasting the link for your reference. You can find more in routing and switching guide.
http://www.cisco.com/c/en/us/support/docs/interfaces-modules/content-switching-module/26220-csm-config.html
Regards,
Kanwal

Citrix and Content Switches

I'm curious if anyone is using the Cisco Content switches to load balance traffic/sessions across a citrix server farm. Any luck and what type of load balancing method did you use? Round robin? Response time? And do these methods REALLY work with Citrix applications/servers for appropriate load balancing?

I just load balanced two Citrix servers using Cisco CSS11150 load balancing switches. Because Citrix uses login for each user, load balancing required stickyness. I load balanced using cookies. This works great. You need to configure the cookie string in the service. You need to configure prefix and length in the content rule. There are several ways to load balance using cookies. The server needs to set the cookie in the first reply back to the client.
[email protected]

Multiple content switches on same subnet

Can anyone confirm if there is an issue having two pairs of content switches (11500s) on the same subnet? The circuit addressing, interface redundancy and VIPs all use the same subnet. Wondering if there would be any issues with the redundancy, arps, etc.. Am stuck with this arrangement during the migration phase of the project.
Appreciate your input.
Rob

Rob,
they can be on the same subnet but they must use different VIP ip addresses.
For the VRRP protocol, you should use different group number on each pair to avoid collision.
Otherwise, that is no problem. I have many pairs like this in the lab sharing the same subnets and this is ok.
Gilles.

Content Switch sending request to both servers

Hi,
I have following configuration on the content switch and it send the request to both the servers. due to two tcp stream from going via two different server it second request fails and generate false alerts.
It was working fine but since last week it is giving lot of false alerts.
content StatePMVQLMVMS_8PR3
    vip address X.X.X.X
    add service W8PRAKLQLM01_StateVMS_8HTTP3
    add service W8PRAKLQLM02_StateVMS_8HTTP3
    advanced-balance sticky-srcip
    port XXXX
    protocol tcp
    active
Please let me know what should I check to get this fixed. I hardly work with content switch.
Is there a way I can set up to send all the request to primary server and when it dies then and only then it send a request to secondary and when primary comes back online it restore back to primary ????
I am fine if it does not load balance .. but at least it stop sending false alerts..
Thanks.

Hi Nilay,
You have configured sticky based on src-ip which means that as long as src IP remains same the user would be sent to the same server.
Now a situation where CSS starts sending the request to different servers could be due to the fact that sticky table was full. In that situation a new connection from same user will be load balanced according to the LB method. If the sticky table is full and none of the sticky entries has expired, the CSS rejects the new sticky request.
You can use sticky-inact-timeout to ensure that sticky entries flush out after they have been inactive for some amount of time.
Please visit the below link for more details about it.
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/css11500series/v8.20/configuration/content_lb/guide/cntntgd.pdf
Regards,
Kanwal

Content Switch Design diagrams

Hi
Can anyone help in providing the web links/articles (with diagrams) that helps to visualize/design a network topology with Cisco 11500 Content Switch & NetApp Cache Engines for load balancing.
Thanks in advance.
Regards // Anoop

if you need reverse-proxy caching here is a good link
http://www.cisco.com/en/US/products/hw/contnetw/ps792/products_configuration_example09186a00800941e8.shtml
For transparent caching, here is another example for a cSS11800 but it is valid for any CSS.
http://www.cisco.com/en/US/products/hw/contnetw/ps789/products_configuration_example09186a0080094352.shtml
Gilles.

DNS request behind content switch: troubleshooting

Hi, sometimes we experience problems resolving a dns name behind a content switch. The problem solves himself after 5 minutes or something like that. We see the dns request on the dns servers subnet. It looks like the is a problem when the packet returns. I'm thinking of a nat problem. How can i best troubleshoot this?

Can i e-mail you the config file? I will also e-mail as soon as possible a network capture in front of the CSS. Where can i e-mail it? For the moment dns is working so i will have to wait for network capture untill it fails again.
Kind regards,
Frederik De Muyter
[email protected]

Sendmail command on Content Switch.

Similar Messages

Maybe you are looking for