Sensors not showing

I installed lm-sensors through pacman and ran the detection script. I've got 4 cores on my CPU but it seems only three are shown when I run sensors (and the word "coretemp" is nowhere to be found).
# sensors
radeon-pci-0100
Adapter: PCI adapter
temp1: +57.5°C
acpitz-virtual-0
Adapter: Virtual device
temp1: +46.0°C (crit = +127.0°C)
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +47.4°C (high = +70.0°C)
it8718-isa-0e80
Adapter: ISA adapter
in0: +1.34 V (min = +0.00 V, max = +4.08 V)
in1: +1.18 V (min = +0.00 V, max = +4.08 V)
in2: +3.34 V (min = +0.00 V, max = +4.08 V)
+5V: +3.01 V (min = +0.00 V, max = +4.08 V)
in4: +3.02 V (min = +0.00 V, max = +4.08 V)
in5: +1.60 V (min = +0.00 V, max = +4.08 V)
in6: +1.18 V (min = +0.00 V, max = +4.08 V)
5VSB: +2.93 V (min = +0.00 V, max = +4.08 V)
Vbat: +3.36 V
fan1: 3154 RPM (min = 0 RPM)
fan2: 0 RPM (min = 0 RPM)
fan3: 0 RPM (min = 0 RPM)
temp1: +25.0°C (low = +127.0°C, high = +127.0°C) sensor = thermal diode
temp2: +54.0°C (low = +127.0°C, high = +127.0°C) sensor = thermal diode
temp3: +46.0°C (low = +127.0°C, high = +127.0°C) sensor = thermal diode
intrusion0: OK
Am I missing something or have I not done something?

I loaded up a fresh ARCH x86_64 install on an Asus M4A785-M board with an AMD Phenom II x4 965 CPU. I ensured that Pacman fully updated everything and then I installed "LM_Sensors".
After running "sensors-detect" and starting the "sensors" service, the output of "sensors" only reported 1 CPU temperature sensor like that listed at the top.
The 925 and the 965 are from the same die family ("Deneb"), so I think what you are seeing is considered "normal" under LM_Sensors.

Similar Messages

MSI Afterburner does not show in game sensors

Hello! today I format my PC but now Afterburner does not show anything in game, and before formatting it worked perfectly with my GTX 970. What can I do?
Thanks!

Hmm not quite should include. It's rather games that include DX. And VC Redist is usually provided by Windows Updates
But great you got it fixed, I was thinking what might be the issue when you posted it.. then fall asleep

I have just installed a new hard drive in my imac intel 20" (2006) and now the hard drive does not show up in the 'select destinations' folder of the install program.

I have just installed a new hard drive in my imac intel 20" (2006) and upgraded the memory and now the hard drive does not show up in the 'select destinations' folder of the install program. I can see the hard drive in the disk utilities window however it wont let me do anything.
It is a seagate 1TB SATA II drive however it is displaying it as a 7.3 TB.
If anyone has any suggestions I would be happy to hear them.
I have tried to erase and partition and get the same error message each time, 'Input/Output error'.
I have tried starting the thing with the install disk which is Mac OS X (Tiger?) which came with the computer. No good.
Anyone?

Thats correct. I can see it in the list however when I attempt to erase it or partition it it's like it's not being found or recognised and it throws up the input/output error message. I am pretty sure that the sensor it attached correctly and it is a SATA drive. I can see all the infor regarding the drive when disk utility is open and it all looks good but I cant access it or do anything with it. It's taunting me!
The install disk is in the drive and the install program runs right up to the point where you have to select the location for the install and there is just nothing in the box where you have to select the hard drive icon.
I have my suspiscions about the drive but any help would be appreciated.

Camera Calibration Profiles do not show in Develop Module LR5 / Windows 7

I have selected three specific camera profiles (Nikon D300, Nikon D700 and Canon G12) and placed them into:
c:\Users\{me}\AppData\Roaming\Adobe\CameraRaw\CameraProfiles\{Nikon D800}
I restarted Lightroom 5 and viewed a RAW photo (not jpg or tif).
But my Nikon D800 or the other two camera profiles do not show up in the Develop Module Camera Calibration drop down menu, nor in the Presets drop down in the Navigator panel.
What am I doing wrong?

DdeGannes wrote:
It is possible to have third party software providers create profiles for your camera that simulate other camera profiles. I have had that done for my Olympus E520 and E300 cameras so that I have dozens of option available.
Yes (to a degree). You can build your own custom DNG camera profiles, that's a good first start. Then you could edit them using the free DNG Profile Editor from Adobe. I'd start with custom profiles for each camera and see if that produces an acceptable match among them.
This may help too:
In this 30 minute video, we’ll look into the creation and use of DNG camera profiles in three raw converters. The video covers:
What are DNG camera profiles, how do they differ from ICC camera profiles.
Misconceptions about DNG camera profiles.
Just when, and why do you need to build custom DNG camera profiles?
How to build custom DNG camera profiles using the X-rite Passport software.
The role of various illuminants on camera sensors and DNG camera profiles.
Dual Illuminant DNG camera profiles.
Examples of usage of DNG camera profiles in Lightroom, ACR, and Iridient Developer.
Low Rez (YouTube):
http://youtu.be/_fikTm8XIt4
High Rez (download):
http://www.digitaldog.net/files/DNG%20Camera%20profile%20video.mov

Component parameters not showing

Hi - I have a series of components I've written in AS3 that work fine in CS3 & CS4. In the Flash CS5 authoring environment, the parameters are not visible in the Component Parameters section of the Property Inspector. The really strange thing is that if I create a .fla in CS4 with the same components on the stage, and then open that doc in Flash CS5, the parameters are visible and work.
Any ideas for how to fix this? What changed in CS5 to make them not work?
Notes:
I've rebuilt the .swc files in CS5 - doesn't fix it
I created an .mxp file for the components and installed with Adobe Extension Manager CS5 - doesn't fix it
The standard components that come with CS5 work fine
My components work fine other than not being able to access the parameters
Any help would be appreciated.
Thanks,
.phil

I think there are several problems going on in the change from CS4 to CS5 with regard to components. But I did find a fix to the problem I had, which is that in components that I built myself, inspectable parameters that worked fine in CS4 did not show up in CS5 (note that parameters moved their location in CS5 - in CS4 they were visible in the Component Inspector panel, in CS5 they accessible in the Properties panel).My components still worked, and were visible in the Components panel, just no parameters.
Here's the solution. When coding a component, you define your inspectable parameters in some code like this:
private var _controller:String = "arduino";
[Inspectable (name = "controller", variable = "controller", type = "String", enumeration="arduino,make,xbee,osculator,inputSource", defaultValue="arduino")]
Elsewhere in the code, you define your getter and setter functions:
public function get controller():String { return _controller; }
public function set controller(value:String):void {
   _controller = value;
   draw();
Based on the examples I had seen when I first started creating components, I put the definition right at the beginning of my class definition, and my getters/setters at the end. Well, in CS5, this approach does not work. To make inspectable parameters work, the definition and getter/setters functions must be together in the code! I put mine right at the end of the class. Like this:
private var _controller:String = "arduino";
[Inspectable (name = "controller", variable = "controller", type = "String", enumeration="arduino,make,xbee,osculator,inputSource", defaultValue="arduino")]
public function get controller():String { return _controller; }
public function set controller(value:String):void {
   _controller = value;
   draw();
Here's where I found the solution: http://f9foractions.tumblr.com/post/903211215/inspectable-parameters-not-showing-up-on-cus tom
Hope this helps!
If you are curious about my components, they are a free system to enable people to work with sensors etc. with the Arduino and other hardware in Flash with no coding required.
http://www.netlabtoolkit.org/
.phil

Mode on t5i not showing

I bought a t5i less than 6 months ago and now for some reason the mode is not showing on the screenwhen changing the different modes. Is there a setting for this ? I can turn the dial however nothing shows on the screen.Any advice or setting ?

1. If something is blocking the sensor just below the flash hotshoe the LCD won't turn on.
2. Pressing the INFO button can turn off the display; this effect is canceled if the camera is turned off and back on again.
3. If these two don't resolve it sounds like camera would need repair.

ITunes does not show up on apple tv 1st gen.

i have a 1st gen apple tv with the 160 gig HD. recently, it will not show the itunes site. Under teh movies tab there are my movies and trailers and that's it. Does anyone know how to get the itunes store back on apple tv?

Known issue currently, you'll need to wait for the fix.

My downloaded text sounds do not show up under the sounds tab in settings after installing 8.1.1. can someone help me please?

i downloaded a couple text tones and since installing 8.1.1, they will not show up under the sounds tab. in fact, they do not show up in my recent purchases on itunes, but when i go to buy them again, it says that i have already bought this tone. I just want to use the tones i paid for as the tones on my phone. not asking much.... thanks for the help. i hope someone can help me get the tones working. thank you.

This was happening to me too but only for some of my songs. I have a mac so I dunno about PCs, but for most of my ringtones I had to create an ACC version in itunes to make them short enough then turn that into a m4r and those all worked fine. But if the song was already short enough and I didn't create an ACC version and just turned the original into a m4r, then it wouldn't appear in my itunes.
so if you're on a mac:
1. go to get info, options, pick when you want the song to start and end.
     Has to be pretty short to work, 30 second or less is good
     if it's already short enough that's fine
2. right click and click 'create ACC version'
     a copy with the length you put in will appear, drag that into a folder or whatever and just type in m4r where m4a would be
     still make an ACC version even if it's the right length
Hopefully this helps someone else.

Internet Streams in Playlists do not show up on Apple TV

I use the following setup:
- Apple TV MD199LL/A (Software 6.0.1) just updated to the latest
- iTunes 11.1.3 for Windows (from a Windows 7 x64)
- iTunes 11.1.3 for MAC (from a Apple MacBook Pro x64, Maverix)
Homesharing is turned on both computers
From both machines I share pictures, videos and music.
All photos, videos and music files are getting displayed on the Apple TV menu, and can be played.
All iTunes playlists from both machines are getting displazed on the Apple TV
BUT!
If a internet stream is added to a playlist, this entry does not show on the Apple TV menu.
If the playlist contains only internet streams the Apple TV menu says "There are no songs in this library"
If I hit the play key on my remote, it will randomly play the first stream in the playlist (not realy reproducable pattern)
I can play those streams in iTunes and send it via AirPlay without problems,
Can anyone help me with this and tell me what I'm doing wrong?
Thank you

You can only view that rental on the iPad. For it to show up it has to be rented directly on ATV or through a computer and streamed via home sharing

When I sync my iPod to my MacBook through iTunes new events do not show up and old events are not deleted. I am using Snow Leopard and not iSync.

I am using Snow Leopard on a MacBook. I have an iPod touch 3G. I do not use iSync it Mobile Me. When I sync my iPod through iTunes new events on my iPod do not show up on my Mac and old events do not delete. I have read help instructions that include deleting the data on the iPod. The iPod has the correct data and the Mac does not so I have not followed those instructions. I need help as the only reason I bought the Mac was to be able to sync, back up, view and print my calendar. Currently it is useless. If only Apple could have learned from the elegance of the Palm software.

Start here:
iPhone, iPad, or iPod touch: Device not recognized in iTunes for Windows

Synced videos do not show up on iPod

Every time I sync my iPod with iTunes, although iTunes says the videos are synced, they do not show up in the Video app on the iPod.
This is a fairly new problem. All these videos have been synced before and they all showed up just fine in the Video app, but as of late the iPod does not show them. Searching for them yields no results.
The videos are in a compatible format and do not have an extremely high definition. Again, I do not think the problem is with the videos, because previously I was able to view them all just fine.
I have at least 1G of memory left, 2G without syncing the videos.
I have erased and re-synced them in iTunes, to no avail. I can play the videos on the iPod from iTunes, but not on the actual iPod device. I'm using windows iTunes, and it is up to date. The iPod software is up to date. I don't want to do a restore because I've already done that multiple times for multiple issues, but if that's what I have to do, I will. It's a pretty old iPod. I'm syncing with a third-party Duracell cable, but I really don't think that's the problem.
I'm not sure what it means, but in iTunes I have checked the option that reads, "Prefer standard definition videos". Syncing with that option unchecked changes nothing so far as I can tell.
Thanks for all your help!
iPod Touch 4th Gen. 8G
iOS 6.1.6
1G free with videos, 2G free without
iTunes for Windows 64-bit V12.1
Duracell 30 pin to USB iPod cable

Try:
- DFU mode and then restore to factory settings/new iPod via iTunes
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
- Try with a new video

Files do not show up on HDD

I tried to get an answer through the iTunes community, and was advised to try here instead as it didn't have anything directly to do with iTunes
Not all iTunes Files not showing up on External HDD
So in a nutshell, all of my 35'000 iTunes files (actual MP3 files) were saved on a TC 2.0TB disk and used on multiple Mac's to pull music from. All music files would be saved and streamed wirelessly from this TC and nowhere else.
I would always add files to this external wireless client and iTunes would work flawlessly playing whatever song I chose through the library.
If I would go in to the iTunes directory (path) and look up files on the HDD the files were just not there (but if clicking on the link through iTunes - show in finder - they would appear on the HDD but only through this method). I gave it no further thought until my TC died (i.e. no longer powers up) on me...
I removed the HDD from the TC and placed it in an USB cradle and after looking into the iTunes folder there are only a fraction of the folders / files much less than expected... When I do a cmd-I I'm told that there are 35'000 files, but they just won't show up.
Any ideas on how i can get all the files to be displayed as I want to copy these over on a new TC and need to map iTunes to this new location/path?

Hello Jfrosa,
Thank you for the details of the issue you are experiencing with File Sharing. I found an article that should help with troubleshooting this:
OS X: How to connect to Windows File Sharing (SMB) using Snow Leopard or earlier
http://support.apple.com/kb/ht1568
Thank you for using Apple Support Communities.
Best,
Sheila M.

Movie rentals that I downloaded onto iMac with Lion to do not show up on ATV 2 in menu for computers. Purchased movies show up just fine. What to do or look for?

I have an imac that is running lion and an Apple TV generation 2. I have rented a movie from itunes and it shows up on my imac in Itunes under a rental icon, and will play fine on my computer. However, it does not show up as choice to play on my apple tv. I have homesharing enabled and everything else works fine including purchased movies that are on my imac, but no where does it show rental movies.
What do I look for? What do I do to play the rental movie on my apple tv 2?

Answer to my own question:
Wait until the downloaded rental has completed its download to the imac. This took a long time for me, since it was part of several things that I was downloading at the same time.
Finally, it showed up on my apple tv. Interestingly, I was able to watch much of the movie on my iMac before the movie finished its download and was available to the ATV 2.

I have an apple iphone 4 that I want to download audio books from my library onto it. I cannot figure out how to do that. The iphone does not show up on my mac laptop as a connected device. Does this kind of download have to run through itunes? Thanks

I have an apple iphone 4 that I want to download audio books from my library onto. I cannot figure out how to do that. The iphone does not show up on my mac laptop as a connected device. Does this kind of download have to run through itunes? Thanks

Yes it is done through iTunes. The iPhone will never show up in Finder as a device. The following is general information on iTunes sync: http://support.apple.com/kb/HT1386 and the following is a previous discussion where the post by Andreas Junge helped others that had a problem syncing audiobooks: https://discussions.apple.com/message/20052732#20052732

HT1657 I rented a movie from iTunes but it is not showing up in the Movies section. What do I do?

I just rented and downloaded a movie from iTunes and now it will not show up in my iTunes library. What do I do?
It DOES show up in iTunes on my iPhone. It DOES NOT show up on my desktop.
Any thoughts? Ideas?
I rented it for a flight I get on in 3 hours. Any quick help would be great.
Thanks.

If the computer iTunes is signed into the same account then contact iTunes:
How to report/refund an issue with your iTunes Store, App Store, Mac App Store, or iBooks Store purchase

Sensors not showing

Similar Messages

Maybe you are looking for