Seperate data in Guest Mode

When operating in guest mode, the guest account can access to the Firefox browser and Google Mail App. Not only has the guest account access the apps, they also have access to my private data.
How do I protect my data from being accessed by the Guest Account?

Hello Freek,
Refer the following link to setup the Guest Mode:
http://www.kb.sony.com/selfservice/documentLink.do?externalId=C1030597
If my post answers your question, please mark it as an "Accepted Solution."

Similar Messages

  • Guest N+1 redundancy & load balancing in seperate data centers

    I need assistance in aquiring documentation to setup N+1 redundancy & load balancing between two seperate guest anchor controllers installed in seperate data centers. Can you explaing how it should be setup or point me in the right direction for documentation? If you can't point me in the right direction to aquire documentation; can you answer the following questions?
    1) How do I setup my mobility groups on my guest anchor controllers installed in the DMZ? Should both guest anchor's be in the same mobility group.
    2) Do both guest anchors share the same virtual IP or do they need to be seperate (DMZ01 - 1.1.1.1 / DMZ02 - 2.2.2.2)? I think seperate!
    3) Are there any configuration parameters on the guest anchors for load balancing?
    4) Do either on of the guest anchors need to be setup as a master controller? I'm not sure?
    5) Are there any configuration parameters on the foreign controllers for load balancing?
    6) How do I setup my foreign controllers? Should both guest controllers be added to the mobility group on the foreigh controller? I would think both of them would be added to the foreign controller mobility group.
    7) Should both guest anchors be added as an anchor on the WLAN? I would think both controllers would need to be added as anchors under the WLAN!
    8) Am I missing anything here? This is how I think it should logically work?
    Thanks,
    Gordon

    I need to elaborate on my questions:
    1) Do both of my guest DMZ anchors need to be in a seperate mobility group on their own or can the guest anchors be in completely seperate mobility groups? All 100 + foreign controllers are in seperate mobility groups.
    I) Example #1: Guest anchor number 1 (Mobility group: DMZ) / Guest anchor number 2 (Mobility group: DMZ)
    II) Example #2: Guest anchor number 1 (Mobility group: DMZ01) / Guest anchor number 2 (Mobility group: DMZ02)
    2) Do both guest anchor controllers have to be configured with seperate virtual IP's or do they share the same address?
    I) Follow up to this question: I want to register the DMZ controllers with our DNS servers so that my clients receive a name when authenticating through my customized webauth. I am currently using 1.1.1.1 as the virtual address and I'm pretty sure this is the address I need to register with my external DNS server. My question is this. Does the address I use for the virtual interface matter? 1.1.1.1 is not a valid address with my network. Do I need to assign a valid address registered with my network if I'm going to add this address to my external DNS servers?
    3) No change to my original question.
    4) No change to my original question.
    5) No change to my original question. I have run into Cisco documentation that mentions guest anchor load balancing, but the documentation is very vague. I'd love to be able to load balance as the network group wants to limit my guest traffic to the internet. I could double my pipe if I could load balance the guest anchors.
    6) No change to my original question, but the answer to question one is key to the setup of my foreign controllers.
    7) Elaboration: Should both guest controllers be added as an anchor under the WLAN on the foreign controllers? I would think both of them would be added.
    8) No change:
    9) Should my secondary guest controller be added as an anchor on the WLAN of the primary guest DMZ controller and visa versa?
    Can my Cisco expert answer this or do I need to open a TAC case?
    Thanks,
    Gordon Shelhon
    SR. Wireless Services Engineer
    Company: Not specified

  • Switchport Stuck in Guest Mode

    I am using 802.1x authentication with multi-domain ports; Phone and PC connected to phone. The phones are Nortel (Avaya) and the PCs are Dell/HP Laptops. All are configured for Certificate authentication and this works well. However we sometimes get some ports stuck in Guest mode. when a non certificated laptop connects to a phone port and fails authentication, the data port is placed in the Guest VLAN. However when the laptop disconnects the port isn't reset and remains in the guest state. When a subsequent good laptop connects and attempts to authenticate the switch ignores this and leaves the data port in the Guest VLAN. Anyone any idea why this happens and how I can overcome it?
    The switch is a 2960S with Version 12.2(58)SE2 IOS.
    The port is configured as follows:
    interface GigabitEthernet1/0/15
    description DANS Port
    switchport access vlan 1807
    switchport mode access
    switchport voice vlan 1855
    priority-queue out
    authentication event fail action authorize vlan 1871
    authentication event no-response action authorize vlan 1871
    authentication host-mode multi-domain
    authentication order mab dot1x
    authentication priority dot1x mab
    authentication port-control auto
    authentication periodic
    authentication timer reauthenticate server
    mab
    dot1x pae authenticator
    dot1x timeout tx-period 7
    dot1x max-reauth-req 10
    spanning-tree portfast
    service-policy input INGRESS-CLASSIFY
    end
    The auth status and mac addresses on the port after the failed laptop disconnects are as follows:
    sh auth sess inter g1/0/15
                Interface:  GigabitEthernet1/0/15
              MAC Address:  Unknown
               IP Address:  Unknown
                User-Name:  UNRESPONSIVE
                   Status:  Authz Success
                   Domain:  DATA
           Oper host mode:  multi-host
         Oper control dir:  both
            Authorized By:  Guest Vlan
              Vlan Policy:  1871
          Session timeout:  N/A
             Idle timeout:  N/A
        Common Session ID:  0AEF212D000003055C8D1DAC
          Acct Session ID:  0x00000653
                   Handle:  0x94000306
    Runnable methods list:
           Method   State
           mab      Failed over
           dot1x    Failed over
                Interface:  GigabitEthernet1/0/15
              MAC Address:  0022.67cd.0eec
               IP Address:  Unknown
                User-Name:  RBT18991
                   Status:  Authz Success
                   Domain:  VOICE
           Oper host mode:  multi-domain
         Oper control dir:  both
            Authorized By:  Authentication Server
          Session timeout:  N/A
             Idle timeout:  N/A
        Common Session ID:  0AEF212D00000026000286D1
          Acct Session ID:  0x00000028
                   Handle:  0xFC000027
    Runnable methods list:
           Method   State
           mab      Not run
           dot1x    Authc Success
    sh mac address-table int g1/0/15      
              Mac Address Table
    Vlan    Mac Address       Type        Ports
    1855    0022.67cd.0eec    STATIC      Gi1/0/15
    Total Mac Addresses for this criterion: 1
    I placed the AAA, dot1x, eap and auth debug on for all events and then connected a good laptop, the only debug message I got were as follows:
    Mar 19 16:17:01.391 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open aut
    Mar 19 16:17:01.653 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open aut
    Mar 19 16:17:02.654 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open aut
    Mar 19 16:17:03.708 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open aut
    Mar 19 16:18:43.784 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_auth_client_present: client for mac address 0022.67cd.0eec has been notified on GigabitEthernet1/0/15
    Mar 19 16:18:43.784 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_auth_client_authorized: client for mac address 0022.67cd.0eec is authorized GigabitEthernet1/0/15
    Mar 19 16:18:43.784 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_auth_client_present: client for mac address 0022.67cd.0eec has been notified on GigabitEthernet1/0/15
    Mar 19 16:18:43.784 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open autn
    Mar 19 16:17:01.391 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open aut
    Mar 19 16:17:01.653 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open aut
    Mar 19 16:17:02.654 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open aut
    Mar 19 16:17:03.708 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open aut
    Mar 19 16:18:43.784 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_auth_client_present: client for mac address 0022.67cd.0eec has been notified on GigabitEthernet1/0/15
    Mar 19 16:18:43.784 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_auth_client_authorized: client for mac address 0022.67cd.0eec is authorized GigabitEthernet1/0/15
    Mar 19 16:18:43.784 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_auth_client_present: client for mac address 0022.67cd.0eec has been notified on GigabitEthernet1/0/15
    Mar 19 16:18:43.784 GMT: AUTH-EVENT (Gi1/0/15) dot1x_switch_is_restrictive_vlan_open_auth:Multi-Host with Guest Vlan/Auth Fail Vlan or open autn
    I would have expected the auth function to have reacted to the EAP packets sent by the good client when it connected and performed eap authentication but it didn't, all it did was say the ports in Guest mode and left the laptop in this VLAN.
    All help will be much appreciated.
    Thanks,
    Paul

    Thanks for this reply, although it does provide valuable information for the "Cisco" world it doesn't help me with the problem I have.
    The big question is as follows:
    Why doesn't the switch react to the EAP packets it gets from the good laptop connected to the port stuck in the Guest state. The port doesn't have a data MAC in its table for the port, only a Voice MAC. It recognises a device has connected as it then places the good laptops MAC in the table BUT it totally ignores the EAP packets from this device and leaves it in the Guest VLAN where the laptop gets a DHCP address once its EAP has timed out.
    Completely wrong activity!!!
    Is this a bug?
    Any help is much appreciated.
    Regards,
    Paul

  • Guest Mode?

    Can an 1100 AP support trunking? Here is what I want to do.
    The switchport is configured for a specific vlan so everything in the wireless cloud is on that vlan currently (LEAP/WEP). I want to setup a seperate open Guest SSID vlan and put it in the same vlan that the outside of my PIX is in. Then build an access list to only allow a few ports open. Like HTTP, VPN, and POP so they can get to the internet/corporate network without hacking into anything.
    Is there a better way of doing a guest mode? Can my idea work?

    The way we do it is we have a guest vlan. This VLAN has no route (no interface VLAN X)on the RSP/RSM, so there is no is way onto the Corporate network. We use an extra interface on the pix(connected to the guest VLAN) which in turn serves as DHCP server and only allows traffic to the web. We also added a small ip pool to the global nat to allow visiting guests to be able VPN out to their home office.

  • Can't view data in browse mode.

    I have a database of about 50 records I can view the data in list mode but when I switch to Browse the page turns grey. I trashed the preferences but no improvement.
    Any help?

    Hello
    - 1 - AppleWorks will NOT be updated. It will be replaced by iWork.
    - 2 - If you wish, you may attach your file to a mail and send it to:
    koenig then a dot then yvan then an @ then tele2 then a dot then fr
    If you do, I will be able to look if the file is working well on another machine.
    So you will know if the oddity is to be searched in your machine itself.
    Yvan KOENIG (from FRANCE mercredi 21 décembre 2005 9:12:42)

  • Locked out of Guest mode on iphone 5 help?

    so I have guest mode enabled on my iPhone and I accidently triple clicked and I don't remember the passcode Ugh.
    I Don't want to restore my phone and I tried going on itunes to try to restart it and nothing? Please help

    There is no "Guest Mode" on an iPhone. Perhaps you mean Guided Access? If you don't remember the passcode, you may have to restore your phone. However, try resetting it first by pressing and holding the Home and power buttons until the apple appears.

  • Precautions to be taken when AA is in Data Take over mode.

    Hi,
    We have an Live SAP System and we are plannning to load Legacy Assets in our system. These Assets are from an acquired Company. We Will be required to put the System in Data Take over Mode during the middle of the year for some time.
    Please let us know what would be the precautions that needs to be taken. For example: Depreciation run, Asset regular Postings, AUC settlements...etc.
    Thanks,
    Raja.

    Hello Raja.
    I believe that SAP note 49563 may help you.
    *This note also have some interesting 'Reference to related Notes'.
    I hope it helps,
    Thaiane

  • Error when opening PowerPoint related to Data Execution Prevention Mode

    I am experiencing an error when attempting to open a PowerPoint file. . Here is the full message: "powerPoint is experiencing a serious problem with PowerPoint com add in. This add-in is incompatible with Data Protection Execution Mode and should be disabled or upgraded to the latest version. Do you wish to disable?" I am using PowerPoint 2010 and Adobe Presenter version 8.

    I've continually experience the same issues. I have updated to Presenter 8.02.
    If I open a project by double-clicking the .pptx file I get the following error message:
    "Run-time error '-2147467259 (80004005)
    SlideShowWindow (unknown member) :Invalid request. Automation rights are not granted."
    If I then enter the Presenter tab and click an option (for instance "Settings") Powerpoint crashes and restarts itself. Once restarted the following error message is presented:
    "PowerPoint experienced a serious problem with the 'adobe presenter powerpoint com adding' add-in. This add-in is incompatible with Data Execution Prevention mode and should be disabled or upgraded to the latest version. Do you wish to disable this add-in from loading?"
    I can often crash Powerpoint with the same DEP warning by closing the presentation with the window's "X" button - Powerpoint restarts itself and gives the same DEP warning as above.
    I normally choose to not disable and continue working. If I then go to "Settings" in Presenter again, it will open without problem. It seems that after four to six occurences like this, Presenter will then be disabled by Powerpoint and require resetting in the File-Options-Addins section.
    Alternately, if I open Powerpoint first and then open my project through the File-Open or Recent Presentations list I do not get the Run-time error mentioned above and usually can open a Presenter option ("Settings") without crashing Powerpoint. I can also close the project without incedent if I use the File-Close menu as opposed the the "X" button.
    I am running Win 7 64bit, Powerpoint 2010 32bit with Presenter 8.02.
    Sincerely hoping support is continuing to monitor these threads, as this one was started in November without much response.

  • Current  date  in  add mode ?

    i want to show the current  date  in  add mode but it s not working
    is there any changes thats working properly.
    If oForm.Mode = SAPbouiCOM.BoFormMode.fm_ADD_MODE Then
                oEdittext = oForm.Items.Item("MrolVal").Specific
                oEdittext.String = Format(DateTime.Today, "ddMMyy")
            End If

    Hi John,
    Try this Code:
    string dtdate=DateTime.Now.Date.ToString("MM/dd/yy")
    string strdate= GetEditTextDateValue(dtdate);
    public   string  GetEditTextDateValue(string  dtdate)
                   try
                        string date;
                        string Year,Month,Day;
                                  Day =(dtdate.Substring(0,2));
                                  Month=(dtdate.Substring(3,2));
                                  Year  =(dtdate.Substring(6,4));
                                  date =(Month.ToString() + "-" + Day.ToString() + "-" + Year.ToString());
                                  return date;
                   catch(Exception ex)
                        throw ex;
    And Finally you can set the Value as
    oEditText.Value=strdate;
    By this way you can set any kind of Date Value to the EditText.
    HTH
    Prashant Bansal

  • How i can change the arabic date and time mode to english date and time mode

    how i can change the arabic date and time mode to english number mode

    Settings app > General > International > Region format.

  • How do i figure it out what app use the cellular data in standby mode?

    How do i figure it out what app use the cellular data in standby mode? I disabled the cellular data for 3 days, and my battery last longer. I don't use push notifications, neither location services. I'm not signed in in skype or any IM app.

    Do you use push email?  Do you have accounts that have synchronized calendars associated with them?  Those features will still use cellular data in the background as the receive mail and send or receive calendar updates.
    Some notifications, like push notifications from Facebook and other social networking sites may use cellular data in the background.  Basically, any automated data task like those may use cellular data when the phone is in standby (note that wifi would be used if available when the phone is active, but wifi turns off in standby and all data goes through the cellular data connection).

  • Can you please provide an example of test case using "Standard Data Output Cascade Mode"?

    Hi,
    I have tried creating a test to check  the "Standard Data Output Cascade Mode". In Vivado 15.1, Ultrascale,  it is working when I have data_width=1. However, if I modify the data_width to greater than 1, then I am not seeing the proper value for .CASCADE_ORDER_B.  Is this expected?
    The RTL is top.v. The addr_width=16, data_width=4. The synthesized vm netlist, test_syn.vm. It contains  8 BRAMS but the .CASCADE_ORDER_B parameter setting in the vm netlist is:
    .CASCADE_ORDER_B("FIRST"),
    .CASCADE_ORDER_B("MIDDLE"),
    .CASCADE_ORDER_B("MIDDLE"),
    .CASCADE_ORDER_B("MIDDLE"),
    .CASCADE_ORDER_B("MIDDLE"),
    .CASCADE_ORDER_B("MIDDLE"),
    .CASCADE_ORDER_B("MIDDLE"),
    .CASCADE_ORDER_B("LAST"),

    Hi 
    The parameter "CASCADE_ORDER_B" specifies the order of the cascaded block RAMs from the bottom to the top of the chain
    for port B.
    So the attribute value FIRST represents the bottom BRAM with respect to cascading. You can cross these attributes by opening synthesized design and observing the property of each BRAM.
    Thanks,
    Vinay

  • Got stuck in guest mode

    I was browsing the internet and downloaded video converter on app store, suddenly a message comes up and said i need to restart press the power button then turn it on again. There was no option of canceling the message that popped up. Then so i did restart my macbook pro. Now im stuck in guest mode. Can someone help me? Im really frustrated to get out of guest mode.

    no need to post again so soon, give people time: https://discussions.apple.com/message/23333421#23333421

  • Can we run 2 payrolls on seperate dates within the same payroll area

    Hi,
    Can someone please tell me is there any possibility in which we can run 2 payroll for seperate PSA and ESG on seperate dates and maintain a commom payroll area for them..?
    Thanks,

    Hi
    Yes we can Run........But u should have either two different date modifiers or Period parameters......
    For Ex:
    Our Pay roll area is X1....Ok and u can run if you same period parameter....
            PayRoll Area          Period Parameter             Date Modifiers
                X1                        P1                                  D1
                X1                       P1                                  D2  
    Or
                 X1                        P1                                D1
                 X1                        P2                                D1
    Loke this we can modify and run....
    Byeeeee
    Edited by: INDRA on Dec 25, 2008 5:43 AM

  • HT1766 How to backup my data in recovery mode?

    I stupetly forgot to back-up my data before upgrading my Iphone5 to IOS 6.1.2, then it turned  into recovery mode, is there any way to backup my data in recovery mode before restoring my Iphone in order not to loose my very important data?

    No.
    Sorry

Maybe you are looking for

  • SQL Developer Not displaying Date columns

    I installed SQL Developer on my machine today and when i query for data I don't find any value in the columns which are of DATE datatype. For Eg if i says select * from dual; i get null as output. Can anyone confirm if this is happening to you also o

  • How to use user defined exception class

    Hi all I just need som help with creating a user defined exception class. Im writing a small/simple text editor. My exception class looks like this: public class myExcp extends Throwable      private String message;      public myExcep(String message

  • Securely downloading a pdf file

    With a web-site configured for https (ssl) do document downloads (like a pdf file) automatically get encrypted/decrypted for the download (by the server/browser)? What about for the case where an URLconnection is used to send the bytes of a file (whi

  • Movie Clip tinting

    I am trying to change the tint of a movie clip using actionScript with the following command myMovieClip.tintColor: #123456; I get this error: must be a simple identifier. Suggestions?

  • Flash Player won't load game in Facebook using Google Chrome

    I have a Windows 7, 32 bit.  I like to use Google Chrome.  I have one game that won't load.  I have went through all the troubleshooting steps.  I noticed that the settings won't save the "use unlimited" setting.  I have changed it several times and