Serial Connector adapter / cable for WAN port on WRT350N and others - WRT150N WRT310N WRT610N

Hello,
On the WAN port, there are 4 pins that are traced to the internal serial traces. Where can we get the cable that will fit into the WAN RJ-45 port and have a serial connector on the back end. It may be called a Cisco Debug Adapter, but we haven't been able to find one and appreciate any pointers. much thanks, joseph
A similar request was made months ago (no longer able to reply) at http://forums.linksysbycisco.com/linksys/board/message?board.id=Wireless_Routers&message.id=71882&qu...

I have been looking for this interface for months. Indeed, a source of the connector would be a great help... We are listening...

Similar Messages

EA6500 manually select speed and duplex for WAN port

Is there any way (hidden settings?) to manually select speed or duplex for WAN port on EA6500? I'm using EA6500 with Genexis HRG1044 (FTTH) and the latter has known issues with upload speed when local device is connected on gigabit. It seems that both EA6500 and Genexis HRG1044 only support autonegotiation and that always results in gigabit which results in poor upload speeds over the internet. Placing 100 Mbps switch between EA6500 and Genexis HRG1044 does the trick but I was wondering if it can be done without it. BTW, my internet speed is only 100/100 Mbps anyways.
Solved!
Go to Solution.

@discoHR If you don't mind me asking, for what purpose do you want to adjust the speed on the WAN port of the EA6500? Is it to increase the upload speed? I'm just spitballing, but I don't think there's any "hidden setting" to adjust it on the EA6500.

Nokia Adapter Cable for USB OTG CA-157

I want to purchase a genuine Nokia Adapter Cable for USB OTG CA-157 . But how ? Nokia store saying they won't sell it . No option to buy it on nokia web site . Online shopping websites having it but is they are really genuine ?
Please give some info or link & cost hint to buy it .

Hi everyone! I'm new here and I searched to find some info about USB OTG cable related to nokia 701 and did not find any. I have a question/problem. I bought a USB OTG cable and it worked with my 701. But It was telling me it is using a lot of power and after a few minutes(1-2) it tells me device is not supported and to disconnect device. After that I tried 3 different usb sticks and all are not supported. I let it go for 2 weeks and tried again and the same story: first is seeing the usb sticks, then not supported. What is the problem? I do not understand. Any ideea? Thanks

Hello. It can be a iPhone4 accessories for the one with pictures and other things are transferred wirelessly to a TV? Thank you

Hello. It can be a iPhone4 accessories for the one with pictures and other things are transferred wirelessly to a TV? Thank you

You need an Apple TV to be able to wirelessly send pictures etc. from iPhone.
However you can buy an adapter if you want to connect to a TV
http://store.apple.com/us/product/MC953

Adapter/cable for display output from Macbook to Samsung 42" HDTV

I am interested in purchasing an adapter/cable that will allow me to connect my Macbook to my HDTV so that I may watch videos I play on my computer (e.g., from hulu.com, etc) on my TV. What do I need to purchase in order to do this? Does the audio output as well?
Please, if you're answering this, use Lehman's terms so that I can understand what's being said thanks in advance!

Hey locasciok1;
First you need a Mini DVI port to HDMI adapter. Look for this on eBay or on something online. WAAAAY too expensive from Future Shop or something. In fact, never get cables from electronics stores, they are always around 5000% marked up. What you will spend $60 to $250 for in store will cost $4 online.
Then, if you have HDMI input on the back of your TV (most new TVs have it, looks like this: http://macpeanut.files.wordpress.com/2009/08/hdmi.jpg) you can run a cable
So get the proper adapter to go from your Macbook to HDMI cable, then the HMDI cable to your TV.
So just post if you do not have an HDMI port on your TV, but post with the specifics of what ports you do have on your TV, whether they are the 3 plug Yellow, Red, White, or the 5 plug, Blue, Green, Yellow Red, White or whatever.
Hope this helps, best of luck!
Message was edited by: MalcolmBell

Activity logging for WAN port on WRT1900ac

Hi everybody, I'm looking to monitor the activity on the WAN port. When the WAN goes on/off line, to find out when I loose connection with my internet provider. I know where to monitor the use of the ports being used, but I'm looking specific to the connects / disconnects on my WAN port towards my provider. Has anybody have suggestions?
John

What region are you located?
Has a Factory Reset been performed?
Was a Factory Reset performed before and after any firmware updates then set up from scratch?
Internet Service Provider and Modem Configurations
What ISP Service do you have? Cable or DSL?
What ISP Modem Mfr. and model # do you have?
Is ISP Modem/Service using Dynamic or Static WAN IP addressing?
What ISP Modem service link speeds UP and Down do you have?
Check cable between Modem and Router, swap out to be sure. Link>http://en.wikipedia.org/wiki/CAT6 is recommended.
Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=88e63d78588142e6bb68e22d7faf2046_Configuring_the_M...
I recommend that you have your ISP check the cabling going to the ISP modem, check signal levels going to the ISP modem. For cable Internet, RG-6 coaxial cable is needed, not RG-59. Check for t.v. line splitters and remove them as they can introduce noise on the line and lower the signal going to the ISP modem. Connecting to the ISP modem could result in a false positive as the signal to the modem could be just enough to that point then adding on a router, could see problems. Ensure modem is working well too. Bad modems are out there as well. The router operation is dependent upon getting good data flow from the ISP modem and the modem is dependent upon getting good signal from the ISP Service.
Not sure if using the following will have information on WAN port activity:
192.168.1.1\sysinfo.cgi

Adapter cable for K8N Diamond Plus PCIE cable?

I guess the K8N Diamon Plus was made before standards were settled, since it has the oldish IDE/Molex power connector for PCIE cards. That while Power Supplies now use the standard connector. Of course there are molex connectors as well on the PS cables, but many power supplies are split into 2 or 4 channels and you're better off using as many channels as possible.
The problem is: I can't find any adapter cable with (female) PCIE --> (male) Molex... I can find cables with one male PCIE and two Molex (don't remember if they were male or female), but not the right kind. I would look more closely now, when buying, and I now know about PS with split/combined settings - but the two PS I have are both "not right" for the Diamond Plus.
Any help with such cables? I'm in Stockholm, Sweden, so something in Europe would be preferred.

Yes, it's a "FSP Epsilon 700 FX700-GLN"
Code: [Select]
Voltage Min.load Max.load Load Reg. Ripple & Noise
+5V 0.5A 30.0A +-5% 50mV P-P
+12V1 0.0A 18.0A +-5% 120mV P-P
+12V2 0.0A 18.0A +-5% 120mV P-P
+12V3 0.9A 18.0A +-5% 120mV P-P
+12V4 0.1A 18.0A +-5% 120mV P-P
+3.3V 0.8A 36.0A +-5% 50mV P-P
-12V 0.0A 0.8A +-10% 120mV P-P
+5Vsb 0.0A 3.0A +-5% 50mV P-P‧+5V & +3.3V total output is 155W max.
‧+5V & +3.3V & +12V1 & +12V2 & +12V3 & +12V4 total output not exceed 680W.
http://www.fsp-group.com.tw/english/1_product/2_detail.asp?mainid=1&fid=98&proid=462

I am unable to set up my new Time Capsule with my BT Home Hub - every time i connect the ethernet cable from Wan port to Home Hub, the internet signal drops

Hi there -
I've just purchased a new Time Capsule, and would like to set up a small home network with my Laptop, iMac and wireless printer. I'm following the first steps, but as soon as I connect an ethernet cable between the WAN port of the TC and the ethernet port of the HH, my BT internet connection drops out and I have to restart the HH. Upon which point it drops out again. The airport utility can see my TC, and gets as far as me typing in the new network name and setting up a password, but then it can't quite get through to the next stage. All the time it's just flashing amber.
Please help!

Setup the TC in bridge mode before you cannot it to the HH.
Simply do the setup fully in isolation. And do it by ethernet.
Setup wireless to create a wireless network.
You can use either same SSID =Wireless name as the HH .. same security same password.
Or use a different name and setup.. totally up to you.
Update the TC and then plug it into the HH by ethernet.

How to use SNMP to access interface counters for WAN port when not in bridged mode

Hi All,
Can't fault my timecapsule, however just struggling to get one little bit of functionality working. I'm keen to get access to the WAN port interface counter information via SNMP, so I can track total bandwidth/throughput & also volume.
I have no issue getting SNMP to work & can see the 2.4 & 5.0GHz network counters, also total number of WIFI clients, wlan0, wlan1 and bridge0 interfaces. Trouble is none of these are the WAN/external ethernet port.
I see that it is likely that I'm trying to find the vlan1 port, however from what I'm reading this may only be available when the device is running in a routed mode (I'm running in bridge mode).
Anyone able to suggest anything?

Some cable modem you can turn off NAT.. and then use the TC in router mode.. or even use DMZ if the cable router allows that.
Have you ever looked at gargoyle router firmware and its ability to count and quota all clients connecting to internet service.. it is a simply fantastic firmware and can be loaded onto a router that costs $70-130 dollars.. it is 3rd party but very solid if you choose the right combo.
http://www.gargoyle-router.com/wiki/doku.php?id=screenshots

RV042G difference between bandwidth - protocol binding for WAN ports

Can somebody explain a little bit better then the manual what the differences are between bandwidth management on WAN ports and protocol bindings?
If you can specify in each section which protocol should go where why having two places to configure this?
Or are there some things to remind when using one of them?

Even if I tell the router to use bandwidth priority for SMTP to WAN2 (and i do not have protocol binding active for smtp to wan2) it still goes to wan1, how does the router choose this kind of behaviour?

IP automatic for WAN port doesn´t works

Hi, I have a RV042 with latest firmware (4.0.4.02) and I´m trying to conect to Internet in port WAN1 with the optino "Obtain an IP automatically". I have noticed that the router receives an IP from the modem, I´m able to connect to the from a PC in the same WAN subnet to the WEB Management page, but in the system summary the Wan Status is IP address 0.0.0.0 default gateway 0.0.0.0 DNS 0.0.0.0 and the pc in the internal LAN couldn't surf Internet.
The only way is assigning an static IP an DNS servers, and then all works fine.
On the system log shows the message "infinite IP address lease time. Exiting" when activate the IP automatically for the WAN1 connection type.
There is no option to change the leased time.
I need to send a router to a remote office where the connection to INternet is with a dynamic IP. Help please

I tried connecting a LAN port to the WAN port and it worked. I then connected the WAN port to the LAN port of a DLink router in series and I could communicate with the internet. I then connected it directly to the Motorola CPEi 150 and the port showed nothing. I then tried to repeat my steps and could not get any responce on the WAN port even with rebooting the router and reverting to factory defaults. The WAN port appears to have intermitten problems. I will attempt to troubleshoot some more but I may have to give up.

Adapter card for firewire ports

iMovie recognizes my camera but will not download. Genius Bar succeeded using an adapter card with firewire ports with assumption that port on computer was bad.
I am searching Apple Store and cannot find this adapter card. What would it be called?
thanks for help

If you mean the online Apple Store, it doesn't currently carry any adapter cards of that type. They are available from many other online vendors. But why not buy one exactly like the one the Genius used, at the store where s/he used it?

Loopback cable for gig port

Hi All,
How to create loopback cable for gig copper port (cisco 6513).
I have tried the following loopback cable:
1-3
2-6
and
1-4
2-5
and
1-3
2-6
4-7
5-8
but interface was not up .Pls suggest if any other option.
This interface is fine. this is just for testing purpose to create loop back cable for future use.
Thanks,
Deep

Deepesh Soni wrote: Hi All,How to create loopback cable for gig copper port (cisco 6513).I have tried the following loopback cable:1-32-6and 1-42-5and 1-32-64-75-8but interface was not up .Pls suggest if any other option.This interface is fine. this is just for testing purpose to create loop back cable for future use.Thanks,Deep
Hello Deep,
If you are handy with building ethernet cables, the simple explanation is;
1. Redirect Pin 1 to Pin 3 and Pin 2 to Pin 6.
2. Make sure you create tight twists to account for signal interference at such a short length.
Hope it Help !!
Regards
Ganeshh Iyer
Rate if it Helps...

How to find MAC address for WAN port for Airport Express 2nd Gen.

The New Airport Express has a LAN and a WAN ethernet ports. How can I find the MAC address for the WAN ethernet port as my Service Provider needs it for provisioning....I can fid MAC address for Ethernet and for two wireless 2.4 & 5GHz but not for WAN ethernet port using Airport Utility 6.1

Many thanks for the swift response. However, there is no WAN MAC address on the box or on the device anywhere. I even used magnifying glass to find one .
The airport utility shows only three mac addresses. One for 2.4GHz, one for 5GHz and one fo the ethernet (LAN port) whereas there is another ethernet port in the device mentioned as WAN port and I am still not able to find the MAC address for the WAN ehternet port for Airport Express (2nd Generation).
Will appreciate a response to make th device work wiht my service provider as providing them the WAN mac address is a must. Had there been an option for cloning mac address, the issue would have not been there.
Many thanks again - in advance.

Do I need to buy extra cable for my macbook pro 2011 and cintiq 12WX?

Hi every one,
I want to buy a cintiq 12wx for my macbook pro 2011 and just wondering if i need to buy extra cable to connect them together. Thank you very much for your responses.

For output from your MBP, you will need to tap either the DVI, mini display port or Thunderbolt port, depending on its age/model. This will connect to the cintiq 12wx via whatever input configuration that they have. I do not know if they supply and cables or not. If it is a VGA input, there are a multitude of adapters available. OWC or Newegg would be good sources to get the proper cables or adapters.
Ciao.

Serial Connector adapter / cable for WAN port on WRT350N and others - WRT150N WRT310N WRT610N

Similar Messages

Maybe you are looking for