Serial number entry in MIGO

Is it possible to enter serial number during Goods receipt against a purchase order?
Say i create PO for 10 Computers and each of them have a serial number. And while doing Goods receipt against a purchase order is there a field for serial numbers to be entered. If so what kind settings to be done.

Hi,
Serial no can be used for the following business transactions.
   1. Goods Receipt/Goods isssue and other inventory postings.
   2.sales orders and delivery notes
   3.maintenance orders
   4.production orders.
Settings:
1. create a serial number profile in customising.
2. Assign the serial number profile in the material master record in work
     scheduling view for fert and raw material check the other views.
Business procedures may be assigned in configuration to a serial number profile.
The assignment to the serial number profile determines if serial numbers are required , can be assigned, must be assigned,are assigned automatically
MMSL : Goods issue , receipts,stockj transfers,stock transport orders
Thanks
nandha

Similar Messages

Serial number entry after posting delivery doc......

hi experts....
we have a requirement in which in the standard sales cycle of Sales order->delivery document posting ( PGI)-> invoice billing the client wants that serial number entry (which is done at the time of PGI) should be done after invoicing(at the end of the day) because as per the business practice of the client, its not practically feasible for the client to enter serial numbers at the time of selling the finished material. The client manually records the serial numbers on the invoice copy and enters the serial numbers for the respective invoices at the end of the day.
Now while testing the client scenario we found that once PGI & invoicing has been done without entering the serial number for the material, the system does not accept any serial number assignment for that material after the completion of sales cycle.
So is there any solution in which serial number can be entered for a material whose PGI and invoicing has been completed?
Thanks & Regards
Vikas Hali

Hello,
As you know the system may not allow to enter the serial number details in the delivery --> Extras --> Serial numbers field, once the delivery is completely PGI'ed and invoiced.
But you may change the same in the table by debug mode. You need to update serial number in the material document in the table level also. Contact your ABAP expert, he may be able to guide you properly.
Prase

Audition CS6 requires a Serial number entry at every startup

Audition CS6 requires a serial number entry everytime I start the program. How do I fix this.? It is very annoying and If I get locked out of the program before I fix the dance recital music Its not going to go well for me here.

You don't say whether you are on Windows or not, but if so you might try running the program once as an Administrator. Once the serial has been accepted, then try running as a regular user.

Disable Serial Number Field in MIGO Screen

Hi all,
I want Disable Serial Number field in MIGO Screen how do i disable ?
is there any user exit or enhancement ?
Anybody please tell me.
Thanks
Regards,
S.Muthu.

S. Muthu
Apply Transaction Variant and Screen Variant through transaction SHD0 for MIGO. Hope it will solve your problem.
Otherwise, discuss this requirement with MM Functional Consultant. In SPRO, it may have some setting to make it display...
Thanks & regards
Amol Lohade

Serial Number Entry Funtion

Is there any way to set the serial number entry funtion DisplayUUTInformationDialog to be modal or floating? I want it to stay on top of the user interface when I scroll through the sequence steps or report for example. I would have thought this would be selectable some way. Like the message pop-up.
Thanks

Hi,
You can override the PRE UUT (http://zone.ni.com/reference/en-XX/help/370052N-01/tsexamples/infotopics/process_model_parallel/).
Skip the existing UUT dialog steps and replace with your own steps which gets the serial number ( using message popup or LV or any other language).
Since its a custom step you can make it the way you want it - modal or non modal.
The default serial number dialog in not modal.
It does the following function which your custom serial step should do :
On user clicking ok on the serial number dialog the parameters.UUT.serial number is updated with the user defined serial number.
Also you need to update the paramters.continue testing if user clicks cancel on the serial dialog.
Hope this helps.
Ravi

Serial Number Problem in MIGO

Hi,
I am using externally created serial numbers and creating an Equipment for them.
At the time of GR of finished product, I am assigning these Serial Numbers to Material in MIGO. When I list the serial numbers in MIGO for selection, system is giving a list but this list consist of Serial Numbers which are already delivered to customer through SD. Serial Numbers delivered to Customer are having system status "ECUS".
My requirement is that system should not list Serial Numbers which are already delivered to Customer.
Moreover if at the time of creation of Serial Number, Plant Code is assigned in the "Stock Data" of Serial Number then system should not allowed it to be assigned to delivery created for some other plant.
I checked all settings for Serial Numbers but could not find any setting for this.
SM

thats good ..
see w_count is a variable of type i.
DATA : W_COUNT TYPE I.
now say that ur code is in
there are 10 entries.
loop.
w_count = w_count + 1.
endloop.
will give me the w_count = 10 okay .
now in here if i say
if w_count > 2.
do scrolling .
w_count = w_count -1 .
endif .
after the two items are filled the page is scrolled ..
here u can see the scroll bar moving down
so third and fourth upto ten will be placed in the cursor position of (2) thats what this logic does ..
regards,
Vijay.
In short more than two line items are there the scrolling starts ..
and u 'll see that the items will be filling up only at cursor two ..
this is how it goes ..
give me ur mail id so that i can send u my complete code for ur better understanding.
Message was edited by: Vijay

VERY URGENT: serial number entry

HI ALL,
In Table MASE - store the last serial number, which is not done by any trasaction from R/3 easy acess, now system considering this entry as a reference for all materil and give serial number.
But user have its own number range like 1300, but as in table MASE the value is stored as 11293, its taking this as a ref number and giving the next serial number like 11294, 11295 etc.
PLZ CAN YOU SUGGEST HOW TO DELETE THE VALUSE 11293 FROM TABLE MASE.
ANS will reward defntly.
Regards
Sid

Hi
We dont have facility to assign no. ranges to Serial No. instead we give No. ranges for Equipment Categories and assign this Equipment Catgoriy to Serial No. Profile.By Assigning the Serial No. profile to a material master, the system will use the Serial Nos from No. ranges for Equipment Category.
U can check the number ranges for equipment category from TC OIEN.
Also is there any custom table for serial number format maintained..???
or any BAPI or FM used in creating customer specific Serial numbers..???
If yes please check ...
Prakash

Asset Serial Number entry via SRM Receipting

Hello,
We have a situation where in our SRM environment, users are creating shopping carts where the Material on the shopping cart line item requires a serial number to be entered upon receipt.
We have not found a good way to allow users to enter the serial number of the item during goods receipt, other than giving them access to t-code MIGO in ECC. We are looking to see if SRM has a way to enter the serial number for assets during the standard SRM receipting process.
I appreciate any help.
Regards,
Charles Braxmeier

Thanks Ray! I couldn't find the UIMessage
Gary,
There is a function...er sorry method.. called ConnectListBarPages in your MainForm.cs file. It looks like this:
  private void ConnectListBarPages()
   // connect listbar page 0 to SequenceFileList
   this.axSequenceFileViewMgr.ConnectSequenceFileList(this.axListBar.Pages[0], false);
   // connect listbar page 1 to ExecutionList
   ExecutionListConnection connection = this.axExecutionViewMgr.ConnectExecutionList(this.axListBar.Pages[1]);
   // display the execution name on the first line, the serial number (if any) on the next line, the socket index (if any) on the next line, and the model execution state on the last line (the expression string looks complicated here because we have to escape the quotes the C# compiler.)
   connection.DisplayExpression = @"""%CurrentExecution%\n"" + (""%UUTSerialNumber%"" == """" ? """" : (ResStr(""TSUI_OI_MAIN_PANEL"", ""SERIAL_NUMBER"") + "" %UUTSerialNumber%\n"")) + (""%TestSocketIndex%"" == """" ? """" : ResStr(""TSUI_OI_MAIN_PANEL"", ""SOCKET_NUMBER"") + "" %TestSocketIndex%\n"") + ""%ModelState%""";
You see that huge string witht the @ sign at the beginning. That is using resource strings to pull the serial number from your execution. If you look closely at this string you'll see the CurrentExecution, UUTSerialNumber, TestSocketIndex, and ModelState being pulled out to update the DisplayExpression. Which is what you see in the listbar. See attached image. All these properties (except currentExecution) are part of your ModelData in your process model. If those don't get updated then according to the logic in the string depends on what gets put in there.
Hope this helps clarify a little. It gets tricky when dealing with multithreading.
Regards,
jigg
CTA, CLA
teststandhelp.com
~Will work for kudos and/or BBQ~
Attachments:
OI.JPG ‏70 KB

Exceeded Serial Number Entry-ordering Recovery Disc

Ordering recovery disc for Pavilion dv7-1245dx. I am in the USA so checked that. Entered the serial number on the order form. Came back incorrect number. Tried again and same error. Tried the letter"O" instead of zero/nil - same error. Then, since the number began with CND I guessed it might be a Candian product. Checked Canada on previous page and re-entered the serial number. This time it said I had exceed the allowed attempts to enter a serial number. The link shown for support was a 404 dead-end. Any suggestions?
Thanks
This question was solved.
View Solution.

Hi,
Check you have the correct Serial No. by checking the entry in the bios. To do this, shut down the notebook. Tap away at f10 as you press the power button to enter the Bios Menu - on the initial page you should see several details relating to your notebook such as Model No. Product No. and also your Serial No.
If you still have problems with the link ( I usually do ), try calling HP directly - the relevant telephone number can be found on the links below.
If you live in the US, contact HP Here.
If you are in another part of the world, start Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Serial Number entry

i have created a serial number profile for deliveries where the user can enter the first serial number manually and create the rest automatically.
Sometimes on large deliveries with 110 pieces have different serial numbers that are not in order assigned to them.
example 20 pieces have a serial number range of 1 -20
40 have it from 40-80
10 have it from 90-100
30 have it 110-140
How can someone enter all of them without manually doing it one by one which is realistically not feasible.
Edited by: saad A on Jun 9, 2009 9:24 PM

Hi there,
When you automate the serial num entry, as per the standard process, system will assign the next available serial num in the system. In your case could be that some serial num in between are already assigned. This is same as generate serial num automatically function where the system will assign the next available serial num.
Regards,
Sivanand

Exit/Badi for Serial number generation in MIGO

Dear ALL,
Requirement: Based on the serial number profile i will maintian the number range in custom table and on doing MIGO system will find the serail number profile thorugh material and based on that system should generate the serial number automatically.
Advise for the user exit /badi ... I have checked some exit starting with IQ.... .
Please provide the exact badi or exit for this purpose.
Regards
Rahul

You can see the local class lcl_migo_globals used in include LMIGOGL1 which inturn has a variable
called kernel with reference to class lcl_migo_kernel. Here exists an example [Serial Numbers Modify in LINE_MODIFY method in MB_MIGO_BADI|http://saptechsolutions.blogspot.com/2011/11/serial-numbers-modify-in-linemodify.html]of accessing & modifying the lines by accessing the call stack using class lcl_migo_kernel and method line_get & line_modify through badi MB_MIGO_BADI .

Deactivate Serial Number Generation in MIGO

Hi,
In MIGO,Serail number generation is made mandatory through Create serial no.s automatically checkbox in serial number tab.The process is such that the user will Check and then Post.So while pressing the Check button,internally serail numbers are generated and while posting the serial numbers are generated skipping the generated numbers in Check.ex.while checking 001 and 002 are internally generated and aftr Post if we check in IQ03 we get 003 and 004;ie 001 and 002 are skiiped.
Can anybody suggest how to avoid serial number generation while Check?

Hi,
Apply Transaction Variant and Screen Variant through transaction SHD0 for MIGO. Hope it will solve your problem.
Otherwise, discuss this requirement with MM Functional Consultant. In SPRO, it may have some setting to make it display...
Thanks
Vikranth

Serial number selection in migo

Hi all,
I need to exclude from/(evidentiate in) MIGO, all serial numbers which I've already selected previosly to let them have a good mvement for ex. 101 or 321 in MIGO.
I'd like to do that, as I can have a big production order, also for 100 or 200 units, and everytime I must select only a little group/number of finished products (5 or 6 a day) from the whole list of serial numbers..
Is there a way to distinguish the serial number already moved?!
regards,
Valentina

It is not possible to remove the serial numbers for existing stock. you need to maintain serial numbers.
If you do not want to maintain serial numbers remove the serial number profile in the material master.
So new stock of material wont ask serial numbers at the time of MIGO

Query about perishable item and serial number entry in RMS

hi ,
can some one help me to explore the below mentioned option RMS
1. how can we mark an item as an perishable item in rms
2. where to enter the serial number for an item in RMS.
regards,
deepak

hi erik,
yeah you are right its an unique number which is assigned to the product by the supplier which is not an barcode or PLU. when i tried to find the same i found vpn and LOV like upc , isbn and oracle retail number etc while i am in the process of creating an item.
i would like to know after we create an oracle retail number or the retailer's own sku number if we want to add multiple ean code and unique serial code how can we execute the same in RMS.
eg 1: a brand of a shampoo will have its common sku number but at the same time it can have multiple ean code/bar codes.
eg 2: mobile phones with common sku number can have IMEI and other codes .
regards,
deepak

Dreamweaver Serial Number Entry Fails - even trial version, serial screen freezes

Well, I have Vista Home Premium, and a new hard drive. I
previously had Dreamweaver CS3 installed, but then had to get a new
hard drive. So, I downloaded the trial off the website, and the
install runs fine. I sold my old copy of Dreamweaver, thinking I
didn't need it. Now, I realize I do need it after all, so I will be
buying a new license.
However, when I first load Dreamweaver, and it asks for the
license or to try the trial, I click try the trial, and "next".
Well, it just freezes on me, and I have to either end the process,
or just let it sit there doing nothing. The installation worked
fine - but it just won't load. I ever tried using a friends serial
key (ONLY to see if I could get past the initial screen), but it
froze, too. I'm glad I haven't bought a serial yet - waste of money
if this won't work.
On the other hard drive, everything worked just fine, and I
deactivated and ran the CS3 installer cleanup. The ONLY change from
then until now is getting a new SATA hard drive, and changing from
IDE mode to SATA on the bios.
I have done three or four reformats, and have tried the
following:
Plain install, with everything in normal state
Reformat, install after installing drivers, some software
Reformat, install with NO drives, except for ethernet
Reformat, install with all drivers, UAC in Vista left ON
I'm out of ideas. I'm tried of reinstalling Vista, although
it does install fast.
Here's what happens:
Copy installer from flash drive to hard drive
Run installer, which extracts itself
Run real installer, installs fine
Reboot (in some cases, didn't)
Open Dreamweaver
Select free-trial (or, in one case, tried friend's product
key)
Click next
Screen freezes
Then, I have tried: ending all Adobe processes (bonjour,
Dreamweaver, licensor, etc), reboot, and try again. Same result
Just reboot, try again - same result
Turn off all firewalls, security devices, etc BEFORE
installing for the first time. Same result.
Uninstalled, ran CS3 cleaner utility, installed again. Same
result.
Again, the ONLY changes are:
Different hard drive (250GB Seagate 7200.10 SATA, instead of
160GB Western Digital Caviar IDE).
So - did the installer off the website change? Does it not
work now? Does it get stuck on the registration page?
I have tried Flash and Photoshop, too. Both have the same
result. What could be conflicting with the licesning service to
make it freeze like that? Can I manually tell it to go to a trial
mode, or manually enter in a license key in some file?
I'm leery of trying a P2P version, which would be an earlier
version of CS3, because I'm not sure what baggage would come with
it, nor do I want to end up in court for trying to get Adobe's
product to work.
Thanks for any help!

Hi barbarawhiting,
Welcome to Adobe forums.
If Jon's solution does not work, close and reopen the application. You are prompted to enter your serial number.
Thanks,
Preran

Serial number entry in MIGO

Similar Messages

Maybe you are looking for