Serial port don't work in windows 2000

I have a Sunray 2 client, Sunray server software 4.
I'm using the sunray conector (RDP Client) to connect to a windows 2000 server.
The serial port mapping is not working when I connect to windows 2000 but if I connect to windows 2003 the serial port mapping work fine.
Any idea???

Windows 2000 doesn't support Serial Port Redirection and other features listed below:
■ Audio
■ Drive mapping
■ Session Directory
■ Smart card redirection
-Shivu

Similar Messages

I pull fiftyfour bytes of data from MicroProcessor's EEPROM using serial port. It works fine. I then send a request for 512 bytes and my "read" goes into loop condition, no bytes are delivered and system is lost

I pull fiftyfour bytes of data from MicroProcessor's EEPROM using serial port. It works fine. I then send a request for 512 bytes and my "read" goes into loop condition, no bytes are delivered and system is lost

Hello,
You mention that you send a string to the microprocessor that tells it how many bytes to send. Instead of requesting 512 bytes, try reading 10 times and only requesting about 50 bytes at a time.
If that doesn�t help, try directly communicating with your microprocessor through HyperTerminal. If you are not on a Windows system, please let me know. Also, if you are using an NI serial board instead of your computer�s serial port, let me know.
In Windows XP, go to Start, Programs, Accessories, Communications, and select HyperTerminal.
Enter a name for the connection and click OK.
In the next pop-up dialog, choose the COM port you are using to communicate with your device and click OK.
In the final pop
-up dialog, set the communication settings for communicating with your device.
Type the same commands you sent through LabVIEW and observe if you can receive the first 54 bytes you mention. Also observe if data is returned from your 512 byte request or if HyperTerminal just waits.
If you do not receive the 512 byte request through HyperTerminal, your microprocessor is unable to communicate with your computer at a low level. LabVIEW uses the same Windows DLLs as HyperTerminal for serial communication. Double check the instrument user manual for any additional information that may be necessary to communicate.
Please let me know the results from the above test in HyperTerminal. We can then proceed from there.
Grant M.
National Instruments

AT-AO-10 doesn´t work with Windows 2000

I have an AT-AO-10 board that doesn’t work with Windows 2000. I have reserved two IRQs for legacy devices (non plug and play) in BIOS. The AT-AO-10 has got assigned these IRQs, a DMA and a base address that are free, and there aren’t any hardware conflicts, but the board doesn't pass the MAX's text.
In Windows 'Information System', the board is shown in 'Forced hardware', but I don’t know that is a problem.
If the board is unplugged, error messages are the same.

Hello;
You didn't mention what version of the NI-DAQ driver you are using over there. Anyway, my suggestion to you is to uninstall the NI-DAQ driver you have installed, remove the board, reboot the machine, download and install the latest NI-DAQ version (6.9.3) from NI web site.
Try the installation with the new driver, and if that is still not working, the best bet is to try the same installation on a different machine to double check if the hardware is not defective.
Regards
Filipe A.
Applications Engineer
National Instruments

AC97 onboard sound DOES NOT WORK under Windows 2000

Just an FYI, the AC97 Audio on your MSI mainboard will not work under Windows 2000, for which the AC97 hardware is not certified. If you try to use it, your audio output will be intermittant at best and will crash your audio applications at worst. A maddening and disheartening problem for people like me who didn't realize the problem existed and spent many hours trying to getting it to go away.

hiya -
I am have this trouble as well!
Are you useing professional, or Advaced server?
I have done EVERY kind of update... so dice.
*sniff *

Ipod not working in Windows 2000

I have a mac at home. I've already synced my ipod and don't want to lose anything on it.
When I try to use the ipod as a usb drive at work with windows 2000, it recognizes the ipod. However, when I try to accsses the drive it says its not formatted and asks if I want to reformat it. I don't want to reformat because then I'll lose everything.
Can I use the ipod as a usb drive on windows 2000 without reformatting?

Never mind. I found XPlay and It works great!
Fred

I'm having trouble communicating with a transducer (Keyence LS-3100 laser scan micrometer) via the serial port. It works in Hyperterminal. Any suggestions?

Its not a simple baud-rate or parity error. If I issue the command to send data (X1) in hyperterminal I start to get data. If I then switch to Labview I still get data. However if I try to issue the send-data command via Labview I get nothing (i.e. I can read from the device, but not write to it).
I am on a Windows 98 (version 2) PC, running Labview 5.1.1

Try adding a carraige return to the end of your command.
"djb" wrote in message news:[email protected]..
> I'm having trouble communicating with a transducer (Keyence LS-3100
> laser scan micrometer) via the serial port. It works in
> Hyperterminal. Any suggestions?
>
> Its not a simple baud-rate or parity error. If I issue the command to
> send data (X1) in hyperterminal I start to get data. If I then switch
> to Labview I still get data. However if I try to issue the send-data
> command via Labview I get nothing (i.e. I can read from the device,
> but not write to it).
> I am on a Windows 98 (version 2) PC, running Labview 5.1.1

ITunes and Quicktime don't work on Windows 7 64-bit

iTunes and Quicktime don't work on Windows 7 64-bit. I tried to uninstall and install the package according to Apple support article (http://support.apple.com/kb/HT1923) but still the same problem. I even tried to stop the Bonjour, it didn't help either. When I try to run either iTunes or Quicktime I get a Windows error message "iTunes has stopped working", with details like this:
Problem signature:
Problem Event Name:          BEX
Application Name:          iTunes.exe
Application Version:          10.3.1.55
Application Timestamp:          4deec351
Fault Module Name:          StackHash_0a9e
Fault Module Version:          0.0.0.0
Fault Module Timestamp:          00000000
Exception Offset:          00000000
Exception Code:          c0000005
Exception Data:          00000008
OS Version:          6.1.7601.2.1.0.768.3
Locale ID:          1033
Any suggestions?
Thanks.
Sergio

Taken as a whole, the symptoms suggest that another application (other than QuickTime itself) has stashed old QuickTime componentry in your system files.
So just in case we'll go looking for older QuickTime componentry in the most common locations for it to be stashed.
First we'll need to change some view settings.
In your Start menu, open Computer.
In your Organise menu, select Folder Options.
In the View tab, make sure that "Show hidden files and folders" is selected, and Hide extensions for known file types is unchecked.
Click OK.
Now in Computer, open your C:\ drive (or whichever drive you have your operating system installed on).
Open the "Windows" folder.
Open the "SysWOW64" folder.
What files and folders can you see in there with QuickTime in the title? (In a standard installation of Quicktime you should be seeing precisely two files... QuickTime.qts and QuickTimeVR.qtx ... and no QuickTime folders whatsoever.)

After update to OS X 10.7.5 on my Mac Pro (2009) USB ports don't work at all after wake up from sleep mode; with 10.7.4 there was (nearly) any problem.

hello,
after update to OS X 10.7.5 on my Mac Pro (2009) USB ports don't work at all after wake up from sleep mode; with 10.7.4 there was (nearly) any problem.
the used ports appear to be "killed"; the unused USB ports seem to work, but the Mac works in slow-motion.
The only "solution" is to restart my Mac.
- SMC-reset, PRAM-reset or repairing user rights had no positive effect; what is the solution - a bug-fix-update???

I have a mac mini (A1283) with OS 10.7.4. Upon upgrading to 10.7.5 it did not start up again. Instead, the light was on and the hard drive did not start up. The light on the connected USB mouse was not lit.
My solution:
Cold start with Command-v pressed.
This should start Verbose mode (see http://support.apple.com/kb/HT1492 ).
What happened on my mac mini was that the grey startup screen with the Apple logo appeared for a long while before the login screen came.
Maybe Cmd-v set open firmware params and fixed some corruption.
Anyway: my mac mini works again.

USB ports don't work - 880GMS

http://
HELP ME
My usb ports work fine until Sunday, I restart the W8 OS and they don't work (my last activity was configure a router but I didn't install anything). I've two OS (W8 and Ubuntu 11.1) and I tried all and my USB ports don't work. I don't have any idea about the cause of the problem. All work fine except my USB ports. They are enable according to the BIOS but the OS (W8, W7 or Ubuntu) doesn't recognize any device.
I tried this things:
- Change my porwer supply
- Restart the BIOS to the Fail-Safe and Optimal value default
- Clear the CMOS (Changing the jumper and remove the battery)
- Remove the W8 and install W7
- Remove W7 and install Ubuntu 11.04
- Flash the BIOS to the last update (it's the same that was loaded in the BIOS)
Currently, I don't know what I must do it. I'm really disappointed with this board (MSI 880GMS-E35). This is my second problem with these model. Previously, I've one and it didn't supply the energy to start the proccesor (Phenon X4 955). My actual board works fine until Sunday.
Please help me to solve the problem.

OK, I have no idea but fortunately my usb ports work fine now.
I don't know how to fix the problem. But I can assure that thanks to Ubuntu it's fixed. My last two operations were:
- Flash the BIOS
- Check lsusb
Yesterday, I'm full disappointed and I was going to prepare my hard discussion with my provider when suddenly I found a this post:
http://askubuntu.com/questions/69594/my-usb-ports-randomly-stop-working-till-a-reboot
But before to enter the command in the Ubuntu's console, I saw that my USB devices work. It's amazing!!! I'm a newer electronic engineer and I saw events similar that this more than once time in my labs (Typical student experiences).
If anyone has the same problem, I could recommend:
- Check BIOS usb options
If these are ok, else enable the propertly options
- Check # lsusb (In Linux)
If your ports don't appear check the PSU (Maybe there are others things that you should check) else
- Check # dmesg | tail (Before and after to connect a usb device)
If there is an error saw in forums, maybe it's the common problem so far (Incompatibility in the kernel -error hci-)
- Type # acpi = force irqpoll
ELSE
- Flash the bios as show in this forum
ACLARATION: I think that this algorithm might help you but I don't prove this. It's your responsible to do that. I only write the items that I learn with this issue.
CONCLUSION: I don't wish that anyone has this problem. I lost one week trying to solve it.
POST RELATED TO USB DON'T WORK CAUSE PROBLEM (ABOUT dmesg and interpretation)
https://bbs.archlinux.org/viewtopic.php?id=102553
POST RELATED TO FLASH THE BIOS
https://forum-en.msi.com/index.php?PHPSESSID=0uaa1psa1gln707een5uu6sb16&topic=138659.0

Working with Windows 2000 ?

Hello, I'm new to Java but been programming 15 years, hell knows why I waited till now to use Java but it is great !
I want to write some applications that control and work with Windows 2000. I realise they would not be platform independent but is this sort of thing possible ?
or .... just as an example what if I wanted to control some feature of the linux os ?
thanks
C

It is possible. All you need to know is how to use JNI. I think there are only two books out there about JNI, I would recommend the one from Sun.
You can download it here: http://java.sun.com/docs/books/jni/index.html

Oracle 8i lite works in windows 2000 ?

I would like to know if Oracle 8i Lite works with Windows 2000 ?
null

IF its a new installation remove the ORACLE key from the REGISTRY.

Desktop themes don't work in Windows 7

Just loaded Windows 7 under Bootcamp. Desktop themes don't work. The choices offered in the Control Panel just don't take when I click on them. I'm stuck with a plain black desktop. What gives? Graphics seem ok but maybe I'm missing something.

Hi lida80,
Welcome to the HP Community, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I will be happy to help you with getting your function keys working for you. You mentioned they don't work in Windows 7 Ultimate, have they worked with other operating systems? If so which ones. What is your product number?
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Why safari 5 and itunes 10 don`t work with windows xp?

Some one knows why the mos recent version of safari and itunes don`t work on windows xp?

Define "don't work". Frankly that's about the most vague and useless statement without some clarification.

My LAN ports don't work on new AirPort Extreme

I just bought a new AirPort Extreme ac and for some reason my LAN ports don't work. Wireless works fine, even extended by an older version of AirPort Extreme. I tried to reset the AirPort, but it didn't help. Any help appreciated.

Defective product that needs to be exchanged, assuming you have checked Ethernet cables, etc. We have seen a few similar posts, but usually with WAN port issues.

Why will a stand alone executalbe with an installer work on windows 2000 and crashes on windows xp professional?

When I run the setup.exe file on a Windows 2000 system it installs properly, but the same file run on a XP Professional system I get an error stating Fatal Error: Installation ended prematurely because of an error.
See here for more information on the specific installer I'm trying to use.
In fact I get this error for any stand alone executable I try to install on any XP machines. I am using LV 7.1. Is there a way to manually install eve
rything?
Thanks

Sure you can Install a lv application manually. just copy the exe-file,
support files in a folder. For the runtimeengine just copy the file
lvrte.dll in the folder of your application or in the windows system folder.
Hope that helps, Niko
BB Herman wrote:
> Why will a stand alone executalbe with an installer work on windows
> 2000 and crashes on windows xp professional?
>
> When I run the setup.exe file on a Windows 2000 system it installs
> properly, but the same file run on a XP Professional system I get an
> error stating Fatal Error: Installation ended prematurely because of
> an error.
>
> See
> HREF="http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=50650000000800000...
for more information on the specific installer I'm trying to
> use.
>
> In fact I get this error for any stand alone executable I try to
> install on any XP machines. I am using LV 7.1. Is there a way to
> manually install everything?
>
> Thanks

Serial port don't work in windows 2000

Similar Messages

Maybe you are looking for