Serial ports not showing up as COMs
Hi,
I currently have the problem where my serial ports don't show up as COMs when I use the VISA resource block. Instead they show up as ASRL1::INSTR for port 1 etc. While this still works ok when I select them manually for running some VI's, some executables where I'm prompted to select a COM port, no com ports show up at all. This is strange because previously I used to be able to see serial ports as COM8 instead of ASRL8::INSTR. Device manager from Windows XP says that the ports are working properly and there are no conflicts. Using Hyperterminal to see information from the serial devices works fine. So i'm not sure what is going on.
One thing I did notice is that in Measurement and Automation Explorer (MAX), three of the ports have the yellow caution sign next to them. One of them is a serial port which says that "VISA port settings are different from the Windows port settings. Go to the Port Settings Conflict tab to resolve the inconsistency." However when trying to resolve this error I cannot save the changes, an unknown error message will come up (maybe because I don't have admin rights on the comp?). The other two ports with the caution sign are Toshiba bluetooth comms. with the device status: "VISA returned this device when finding resources, and MAX could use VISA to parse the resource name. MAX could not succesfully open a VISA session to the device" with no clues on how to fix.
Has anyone had any experience with these sort of problems and how to resolve them.
Thanks,
William
Hi
Thanks for the quick replies. The VISA Aliases from MAX seems to be set up properly, just that when I go to select a com port in LabView, they show up as ASRL1:INSTR etc. This isn't such a big problem as selecting ASRL still works ok, just that some executables and VI's i'm trying to run is written so as to scan for the string "COM" while they search for com ports so when that happens I can't run them since there's nothing to select. I've attached a couple of screenshots of what I see (note that some of the serials ports, the device status says device is working properly, just the ones I took screenshots off, it seems to have an error).
Attachments:
VISA select screenshot.JPG 55 KB
MAX com screenshot.JPG 64 KB
MAX ASRL screenshot.JPG 63 KB
Similar Messages
-
Serial ports not appearing in MAX - VISA installed.
Hi All,
Had a rather strange issue today that I couldn't resolve with serial ports not appearing in MAX (and hence being inaccessible to LabVIEW). Under the windows device manager it shows 4 COM ports and I have verified with an external program that they are functioning correctly.
I had the LabVIEW 2011 SP1 f2 runtime installed, DAQmx 9.6.1 and NI-VISA 5.3 (5.2 also didn't work).
Things I have tried:
- Updating VISA from 5.2 to 5.3
- Reinstalling the COM port devices under device manager
- Changing the COM port numbers
- Verifying that the COM ports are functioning correctly
- Tried adding a USB to Serial converter as a new COM port
- Reinstalling MAX
- Reinstalling NI-VISA
- Reinstalling everything (reboot each time when prompted)
- Resetting the hardware configuration from within MAX
- Run installers / MAX as administrator (this is running from the local admin account)
- Checked that NI-VISA appears under software in MAX
- Repaired MAX/NI-VISA
Is there anything else that could cause the COM ports not to appear in MAX when they appear (and work correctly) in device manager when a reinstall of NI VISA / MAX won't solve?
Certified LabVIEW Architect, Certified TestStand Developer
NI Days (and A&DF): 2010, 2011, 2013, 2014
NI Week: 2012, 2014
Knowledgeable in all things Giant Tetris and WebSockets
Solved!
Go to Solution.I found the solution - it turns out that the serial ports were available to LabVIEW, they just didn't show up in MAX because installing just the runtime does not show the devices in MAX.
Despite doing a lot of googling earlier, it didn't throw up this knowledgebase article until I searched for it under a different phrase - http://digital.ni.com/public.nsf/allkb/766FD80DAE42E52886256A0200619CFE?OpenDocument
Certified LabVIEW Architect, Certified TestStand Developer
NI Days (and A&DF): 2010, 2011, 2013, 2014
NI Week: 2012, 2014
Knowledgeable in all things Giant Tetris and WebSockets -
I have a dive program called Macdive and am trying to upload my dives from my Sherwood Wisdom dive computer via usb lead. The dives will not upload and program says that serial port not found. does anyone know how I can activate?
Try a new post in the appropriate iPhoto forum.
DALE -
KM2M serial port not working in Linux
I noticed a few Linux postings so I thought I'd give this a shot. I'm running Fedora Core and for some strange reason I can't seem to send any communications out to the ttyS0 (COM 1) or ttyS1 (COM 2) ports.
Does anyone have any suggestions on making it work?
Thank you.No, your code had no termination characters at all - automatic or not. The enable termination character for the VISA Configure Serial Port is only for reads. Just like the help explains.
And while you should check the download page for updates, LabVIEW comes with the 34401 driver.
Message Edited by Dennis Knutson on 12-19-2009 05:49 PM -
My Lightroom 5 upgrade serial number not showing up on My Products page; chat support useless
I purchased a Lightroom 5 upgrade license on July 25th. I didn't receive a confirmation email but my serial number was displayed on the order summary page after purchase. I tried registering the serial number repeatedly through the My Products page but for some reason the serial number wasn't showing up, even though the registration process reported a successful result. Furthermore, Adobe products bought from the Adobe store should automatically be registered according to Adobe's web site. Apparently this must have failed. I need to reinstall Lightroom 5 but the serial number is still not showing up on the My Products page. I just spent an extremely frustrating hour with Adobe "Live" chat who did nothing but send me in circles and repeat the same canned responses over and over again.
I'm currently on hold with "phone support" but I'm not optimistic as I've been on hold for 28 minutes. The only other support option was a link to this forum, hence this post. Hopefully someone from Adobe can retrieve my serial number and contact me. Failing this my only other option will be to contact VISA and open a claim.
My comical-if-it-weren't-so-sad conversation with Adobe support:
Hi, there are 36 customer(s) in line ahead of you. We'll be with you as soon as possible. Thank you for your patience.
Hi, there are 35 customer(s) in line ahead of you. We'll be with you as soon as possible. Thank you for your patience.
Hi, there are 31 customer(s) in line ahead of you. We'll be with you as soon as possible. Thank you for your patience.
You are now chatting with Bhagawan.
Bhagawan: Hello! Welcome to Adobe Customer Service.
Joel: Hello
Bhagawan: Hi Joel.
Joel: I need to reinstall Lightroom 5 but my serial number is not showing up under My Products & Services on the website
Joel: I bought a Lightroom 5 upgrade back in July
Bhagawan: I will be glad to check and help you with this issue.
Joel: For some reason the product registration is not showing up under my account. I have my VISA transaction info if it helps you find my purchase.
Joel: Thanks
Bhagawan: I'll be right with you.
Joel: ok
Bhagawan: Okay.
Bhagawan: May I know the email address, please?
Joel: ******
Bhagawan: Thank you.
Bhagawan: Let me check on this.
Bhagawan: For security reasons, could you verify your complete name and billing address as mentioned on your account please?
Joel: Sure:
Joel: Joel ****
Joel: **********
Bhagawan: Thank you Joel.
Bhagawan: Joel, I see that your serial number is registered under your adobe account, please sign out and sign in your adobe account click on My Products and service information to retrieve the serial number.
Joel: I only see Lightroom 4 ... not Lightroom 5.
Joel: But I'll try
Joel: Give me a sec
Bhagawan: Sure.
Joel: Nope...still only shows Lightroom 4
Joel: Products in use Version Platform Registration date Lightroom 4 Mul October 4, 2012 Register new products
Bhagawan: Okay.
Joel: Not sure why it isn't showing my upgraded license for Lightroom 5
Bhagawan: Please give me a minute or two.
Joel: ok
Bhagawan: Sure.
Bhagawan: Thanks for staying online.
Joel: np
Bhagawan: Joel, In this case, I'll transfer this chat to our Concern Team to check and help you with the serial number.
Joel: ok
Bhagawan: Please stay online.
Joel: ok
Please wait while I transfer the chat to the appropriate group.
You are now chatting with Naveen R.
Naveen R: Sorry for the wait. Please do stay online.
Naveen R: Hello! Welcome to Adobe Customer Service.
Joel: ok
Joel: Hello
Naveen R: Hi Joel.
Naveen R: I understand that you are unable to locate the serial number.
Joel: I purchased Lightroom 5 on July 25, 2013 as an upgrade for Lightroom 4. I need to reinstall Lightroom 5, but my serial number is not showing up in the products & services page.
Joel: I looked through my email receipts and couldn't find an order confirmation (or anything from Adobe related to my recent purchase.) After purchasing the upgrade, the serial number was displayed and I thought I had registered it using the Adobe account portal
Joel: Apparently, this didn't work. I have my VISA transaction information if required.
Naveen R: Thank you for the information.
Naveen R: I will be glad to check and help you with that.
Joel: Thanks
Joel: As I mentioned to the previous agent, when I got into My Products on the Adobe portal, I can see my Lightroom 4 info, but the Lightroom 5 Upgrade info isn't there.
Joel: got = go
Joel: sry
Naveen R: Thank you for waiting. One moment please.
Joel: ok
Naveen R: I'll be right with you.
Naveen R: Sorry for the wait. Please do stay online.
Joel: ok
Naveen R: Thank you for waiting. One moment please.
Naveen R: Sorry for the wait. Please do stay online.
Joel: Will it take much longer?
Naveen R: Let me check on that.
Joel: Are you alive?
Naveen R: I'm sorry due to application error I'm unable to check on that.
Joel: Can I please get a phone number to call? My only other choice would be to open a claim with VISA for fraud since Adobe seems unwilling to help in this matter
Naveen R: I will provide the steps to locate the serial number on your Adobe account.
Joel: I already know how to look for a serial number. The problem is that it doesn't show up in the Adobe account portal.
Naveen R: Please login under a different browser.
Joel: Already tried. Used IE then Chrome
Naveen R: Delete the cookies refresh your browser.
Joel: Same problem
Joel: Please provide me with a number to call
Naveen R: *Once you login to the Adobe account, click on "My products" under the "My products and services".
Naveen R: *There you can locate the serial number which you have registered.
Joel: I've already done that.
Joel: It is NOT listed
Joel: Which I've been saying for the past 40+ minutes
Naveen R: May I know the email address you logged into Adobe account?
Joel: ******
Naveen R: Thank you.
Joel: ...
Naveen R: Thank you for waiting. One moment please.
Naveen R: I see that your serial number is registered under your account.
Joel: Lightroom 5
Naveen R: I will provide you the serial number via email after ending this chat.
Joel: ok but please make sure it isn't Lightroom 4 but my Lightroom 5 serial number
Naveen R: Yes. Due to some technical error you are unable to locate it.
Joel: ok please send the serial number
Naveen R: Sure.
Naveen R: Is there anything else I can help you with?
Joel: No
Naveen R: You are welcome.
Naveen R: Thank you for contacting Adobe. We are available 7 days a week, 24 hours a day. Goodbye!
This chat session has ended.
Thank you for contacting Adobe.OK, I was able to recover my previous system's image and thankfully it appears you can get the serial number from Help->System Info. I attempted to register the serial number again via the My Products page and while it indicated that the registration was successful, we'll see. At least I should be able to install LR5 on my new machine now.
Edit: I also just discovered that the serial number is listed under My Orders, but not under My Products. Weird. In my defence , I never thought to check My Order history because I never received a confirmation email and the order wasn't listed after purchase...even as late as mid-August (when I last checked.) Very strange but it's all good now.
Edit #2: OK now I just feel silly. I just received an email from Naveen with an actual support case AND the correct serial number. So, I stand corrected. The Live Chat process still felt incredibly long with some seemingly canned/automated responses but, in all fairness, he did get back to me. Thank goodness I washed both feet today... -
Serial number not showing up in system profiler
hi,
i recently had a problem with my speakers in macbook.
i sent it for service and the service center replaced my main board
now the system profiler is not showing my serial number.
do any one know how to fix this problem.You would need to send it back to have the serial number burned in to the board. This seems to be a common occurrence when the board is replaced. There should be a number you can call on the paperwork from the repair and discuss it with them.
-
Thunderbolt port not showing connected device
I'm trying to use my 2d iMac 27" as a second monitor. I have the two iMac's connected via thunderbolt ports systems do not show any devices connected to either port.
Also, CMD F2 function (Target Display Mode) is not working.
Has anyone else this problem?
ThanksThanks dastoelk & Russ,
That definitly sounds like the issue, but the only thing new on the drive since the last time I opened FCPX is some new P2 media that's buried in the "PROJECTS" folder and some NEFs from a school play I recently filmed, in the "Greater Tuna" folder. But I have other P2 media and NEFs on this drive that have been on it for a while. Also, forget to mention, runnig FCPX 10.0.9 -
Serial Port not accessible until I run MAX
Hi!
On my machine I can access all Serial ports perfectly. I put a Vias Resource in my VI and get a drop down menu with all my serial ports. But on other machines (Runtime v7 and VISA runtime installed) I don´t get the names (e.g. com1 com2) but only
ASRL1:****
ASRL2:****
ASRL10:****
I know that ASRL1 is COM1 but when I select it it dowsn´t work.
If I now install MAX on the machine and run it once without changing the configuration my ports work.
Can anybody tell me how to use the ports without using MAX??
regards
hmannHi hmann,
When you run MAX it is configuring your VISA alias list behinf the scenes. See "JB" answer to this question to find out how to do this without using MAX. It basicly requires editing an INI file.
http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=506500000008000000238D0000&UCATEGORY_0=_49_%24_6_&UCATEGORY_S=0
I hope this help,
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction -
Tecra A11 - Serial port not working
I have a Tecra A11 running windows 7 professional (32 bit).
My serial port does not appear to be operating as I am no longer able to connect to industrial automation PLC's which require connection to the serial port for programming.
Some of the software I am using is RSLinx, Easysoft and the like.
Any assistance with this matter will be greatly appreciated.Hello
I assume you need the notebook at your company and normally in every company there is a local IT-Support that you can ask all questions if you have any problems.
So I would recommend contacting an administrator. Usually the guys know how to connect the computers to all important industrial components/computers and how to configure the port for that. -
LACP using 2x 10G ports not showing 20G?
I currently have etherchannel configured to 2x 10g ports.
Cat_6509#sh run int ten8/1
Building configuration...
Current configuration : 156 bytes
interface TenGigabitEthernet8/1
switchport
switchport mode trunk
channel-group 42 mode desirable
end
Cat_6509#sh run int ten9/1
Building configuration...
Current configuration : 156 bytes
interface TenGigabitEthernet9/1
switchport
switchport mode trunk
channel-group 42 mode desirable
end
Cat_6509#
Cat_6509#sh int t8/1
TenGigabitEthernet8/1 is up, line protocol is up (connected)
Hardware is C6k 10000Mb 802.3, address is fc99.4736.a2f0 (bia fc99.4736.a2f0)
Description: 10 Gig GEC to MADDC (Spanned VLANS)
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 5/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Gb/s
Cat_6509#sh int t9/1
TenGigabitEthernet9/1 is up, line protocol is up (connected)
Hardware is C6k 10000Mb 802.3, address is fc99.4736.a238 (bia fc99.4736.a238)
Description: 10 Gig GEC to MADDC (Spanned VLANS)
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 8/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Gb/s
Cat_6509#sh int po42
Port-channel42 is up, line protocol is up (connected)
Hardware is EtherChannel, address is fc99.4736.a2f0 (bia fc99.4736.a2f0)
Description: 10 Gig GEC to MADDC (Spanned VLANS)
MTU 1500 bytes, BW 20000000 Kbit, DLY 10 usec,
reliability 255/255, txload 7/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Gb/s <<<<<<<<<<<<<<<<<<<<<<< Should this be 20GB if the ports are bundled?
Cat_6509#show etherchannel 42 summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use N - not in use, no aggregation
f - failed to allocate aggregator
M - not in use, no aggregation due to minimum links not met
m - not in use, port not aggregated due to minimum links not met
u - unsuitable for bundling
d - default port
w - waiting to be aggregated
Number of channel-groups in use: 28
Number of aggregators: 28
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
42 Po42(SU) PAgP Te8/1(P) Te9/1(P)
Last applied Hash Distribution Algorithm: Fixed
Cat_6509#
Thanks
STHi WannaB
Oops you are right the configuration is in PagP. However I have another port channel from the 7706 to Fabric Interconnect which is configured as LACP that is still operating on 10G.
ethernet# show int po30
port-channel30 is up
admin state is up
Hardware: Port-Channel, address: 8480.2da5.c36c (bia 8480.2da5.c36c)
Description: UCS Fabric Interconnect A
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, medium is broadcast
Port mode is trunk
full-duplex, 10 Gb/s
ethernet# show port-channel summary
Flags: D - Down P - Up in port-channel (members)
I - Individual H - Hot-standby (LACP only)
s - Suspended r - Module-removed
S - Switched R - Routed
U - Up (port-channel)
M - Not in use. Min-links not met
Group Port- Type Protocol Member Ports
Channel
1 Po1(SD) Eth NONE --
2 Po2(SD) Eth NONE --
3 Po3(SU) Eth LACP Eth1/2(P) Eth2/2(P)
30 Po30(SU) Eth LACP Eth1/5(P) Eth2/5(D)
ethernet# sh run int eth1/5
!Command: show running-config interface Ethernet1/5
!Time: Thu Dec 11 02:43:46 2014
version 6.2(8a)
interface Ethernet1/5
description UCS Fabric Interconnect A
switchport
switchport mode trunk
channel-group 30 mode active
no shutdown
ethernet# sh run int eth2/5
!Command: show running-config interface Ethernet2/5
!Time: Thu Dec 11 02:43:48 2014
version 6.2(8a)
interface Ethernet2/5
description UCS Fabric Interconnect A
switchport
switchport mode trunk
channel-group 30 mode active
no shutdown
ethernet# -
Serial number not showing on delivery or invoice
Hello I am trying to get serial numbers to print out on Delivery and Invoices. According to Suda in a prior thread (Serial Number on the Delivery Challan) this is suppose to happen automatically in 2007 versions of SBO. I have created a test item (serial numbers setting "On Every Transaction"), rcvd the item and assigned it a serial number.
I then input a Delivery for the test item and printed it to the screen (draft) before posting it via the "Add" button. The draft did not show the serial number. I did the same for an invoice using the test item and again the serial number did not show on the draft invoice.
What step am I missing to get the serial number to print on the delivery and invoice?
What is required to get the serial number to print out on other forms such as credit memos and sales returns?Hi
You are right . So far some other thread has been generated also before identifying same issue .
The option you have :
1. Administration --System initialisation -print preference >AR Invoice
However , if you want to bring it your serial number in one invoice , you probably need to customise your PLD .
2. AR invoice donot show serial number at row level because serial number is stored in different table .
Right click on AP invoice with serial number and Serial number transaction report or By menu bar Goto -->Serial Number and transaction report .
Hope this will narrow down what you are looking for
Thank you
Bishal -
Serial port not reading after few seconds PLZ HELP...
Hi,
I have developed a GUI using Swing in NetBeans IDE 4.0 on Windows 2000 professional for one of our products.
It communicates with the associated Hardware through serial port.
The GUI sends commands to the H/W to perform some functionality. After receiving response from the H/W, GUI displays the necessary messages.
Since the H/W does require some time to perform the indicated operation, it sends the response after 10-11 seconds but my GUI is not reading the response.
Both the command and response are single byte (8 bits) wide.
The GUI can read the response if sent within 3-4 sec.s but not after that.
I have disabled the Receive TimeOut on the serial Port.
Following is the code I use to Open and use the SerialPort.
public void OpenPort(){
portList = javax.comm.CommPortIdentifier.getPortIdentifiers();
while (portList.hasMoreElements()) {
portId = (javax.comm.CommPortIdentifier) portList.nextElement();
if (portId.getPortType() == javax.comm.CommPortIdentifier.PORT_SERIAL) {
if (portId.getName().equals(Welcome.CommPort)) {
try {
serialPort = (javax.comm.SerialPort)portId.open("FCAT-01 ATE", 20000);
} catch (javax.comm.PortInUseException e) {}
try{
serialPort.addEventListener(this);
}catch (java.util.TooManyListenersException e){}
serialPort.notifyOnDataAvailable(true);
try {
outputStream = serialPort.getOutputStream();
} catch (java.io.IOException e) {}
try {
inputStream=serialPort.getInputStream();
}catch (java.io.IOException e){}
serialPort.notifyOnDataAvailable(true);
try {
serialPort.setSerialPortParams(Welcome.Speed, javax.comm.SerialPort.DATABITS_8, javax.comm.SerialPort.STOPBITS_1,
javax.comm.SerialPort.PARITY_NONE);
} catch (javax.comm.UnsupportedCommOperationException e) {}
serialPort.disableReceiveTimeout();
Pls help me how to solve this problem as its really very urgently necessary to release the product.
Thank u for ur time and consideration,
Umesh BalikaiSir,
Here is the complete code.
The H/W takes about 10 seconds to reply. The GUI is responding to first response from ATE H/W and not to the subsequent ones. The ATE responds after the GUI sends command when the user clicks OKButton.
package my.ate.pkg;
import javax.swing.*;
import java.util.*;
public class PingTest extends javax.swing.JFrame implements javax.comm.SerialPortEventListener{
/** Creates new form PingTest */
public PingTest() {
initComponents();
private void initComponents() {
// create and initialise various buttons, labels, etc.
private void OKButtonMouseClicked(java.awt.event.MouseEvent evt) {
// TODO add your handling code here:
OKClick();
public static void main(String args[]) {
java.awt.EventQueue.invokeLater(new Runnable() {
public void run() {
new PingTest().setVisible(true);
// Variables declaration
private javax.swing.JLabel AN;
private javax.swing.JButton OKButton;
public static java.io.OutputStream outputStream;
public static java.io.InputStream inputStream;
public static java.util.Enumeration portList;
public static javax.comm.CommPortIdentifier portId;
public static javax.comm.CommPort commPort;
public static javax.comm.SerialPort serialPort;
public static byte[] readBuffer=new byte[20];
public static int numBytes=0;
private java.awt.Color Fail=java.awt.Color.red;
private java.awt.Color Pass=java.awt.Color.blue;
public static int requestCommand;
public static int receiveCount=0;
public static boolean portOpen=false;
// End of variables declaration
public void serialEvent(javax.comm.SerialPortEvent event){
switch(event.getEventType()){
case javax.comm.SerialPortEvent.BI:
case javax.comm.SerialPortEvent.OE:
case javax.comm.SerialPortEvent.FE:
case javax.comm.SerialPortEvent.PE:
case javax.comm.SerialPortEvent.CD:
case javax.comm.SerialPortEvent.CTS:
case javax.comm.SerialPortEvent.DSR:
case javax.comm.SerialPortEvent.RI:
case javax.comm.SerialPortEvent.OUTPUT_BUFFER_EMPTY:
break;
case javax.comm.SerialPortEvent.DATA_AVAILABLE:
try{
numBytes=inputStream.read();
if(numBytes==0x54) {
// display some message
else if(numBytes==0x41) {
// display some message
else if(numBytes==0x46) {
// display some message
else if(numBytes==0x42) {
// display some message
}catch (java.io.IOException e){}
break;
public void OKClick(){
if(portOpen){
serialPort.close();
portOpen=false;
OpenPort();
try{
Thread.sleep(500);
}catch(java.lang.InterruptedException e){//display error}
try{
outputStream.write(0x39);
}catch(java.io.IOException e){//display error}
//display some Progress Message
public void OpenPort(){
portList = javax.comm.CommPortIdentifier.getPortIdentifiers();
while (portList.hasMoreElements()) {
portId = (javax.comm.CommPortIdentifier) portList.nextElement();
if (portId.getPortType() == avax.comm.CommPortIdentifier.PORT_SERIAL) {
if (portId.getName().equals(Welcome.CommPort)) {
try {
serialPort = (javax.comm.SerialPort)portId.open("FCAT-01ATE",2000);
} catch (javax.comm.PortInUseException e) { //display error}
portOpen=true;
serialPort.notifyOnDataAvailable(true);
try{
serialPort.addEventListener(this);
}catch (java.util.TooManyListenersException e){ //display erro}
serialPort.disableReceiveTimeout();
try {
outputStream = serialPort.getOutputStream();
} catch (java.io.IOException e) { //display erro}
try {
inputStream=serialPort.getInputStream();
}catch (java.io.IOException e){ //display erro}
serialPort.notifyOnDataAvailable(true);
try {
serialPort.setSerialPortParams(Welcome.Speed, javax.comm.SerialPort.DATABITS_8, javax.comm.SerialPort.STOPBITS_1,
javax.comm.SerialPort.PARITY_NONE);
} catch (javax.comm.UnsupportedCommOperationException e) { //display erro}
}Probably the command after clicking OKButton is not reaching the H/W. because the ATE will surely respond if it receives the command and that is tested several times.
Thanks. -
My backup drives and flash drives have disappeared from the desktop. I have unplugged everything, rebooted and they're still not showing up. I checked the drives with my other computer and they are all fine. They are just not being recognized on the HP Envy.
Did this happen after an update of some kind? Consider using Microsoft system restore to revert back to a checkpoint dated before the update happened. You wil not lose anything important on your PC by doing this and system restore is reversible.
-
Desktop software. serial port not configured properly
i cant seem to configure my serial port. actually i just dont know how.....ive went into serial setting but i cant seem to find a port number. it doesnt detect anything.....????? can someone with some patience pleeeeeeeese help me. thx alot
Port is supposed to be auto detected!! Have you tried detecting the port manually by going to connection settings and pressing detect button ? Which version of desktop manager your're using?
tanzim
If your query is resolved then please click on “Accept as Solution”
Click on the LIKE on the bottom right if the post deserves credit -
Transaction IQ09 u2013 production ORDER number for the serial number not showed
In the ALV generated by IQ09, we couldn´t see any production order number with its respectives serial numbers listed.
We try to check in NOTES SAP, through "SER*" tables and programs RIQEUI21 and RIOBJK00, but without success.
In the IQ02 and IQ03 transactions, we can find the orders numbers, but our users would like to see at the ALV list.
Anybody knows any transaction that shows serial numbers and production orders in a unique LIST.
Thanks
Claudio.Hi,
I think you can customized your requirement, see below table
In table SER05, the list of serial number details can be obtained. key the order no in SER05 table, get field OBJKNR, then pass this OBJKNR in table OBJK .
Some useful table for serial numbers
SER00 Generic table for serial numbers
SER01 Serial numbers assigned to a delivery
SER02 Serial numbers assigned to a guarentee
SER03 Serial numbers assigned to a material document
SER04 Serial numbers assigned to an inspection lot
SER05 Serial numbers for a production order
SER06 Serial numbers for Handling Units
SER07 Serial numbers for Stocktaking
SER08 serial numbers for Orders (SD)
I hope that this information clarifies the issue.
Regards,
Sankaran
Maybe you are looking for
-
How do i move my itunes library from my pc to the icloud?
i have 3900 songs stored in my itunes library on my laptop. I recently got an i phone 4S and there isn't enough storage on it to move my songs to the phone. I purchased 20gb of storage in the iCloud but can't find any instructions to move my librar
-
ICal error message: reenter password. . .
I continue to experience an aggrivating message from iCal. "The password may have been entered incorrectly. Reenter the password for account "Yahoo!" on the CalDAV server "caldav.calendar.yahoo.com." At the top of the iCal message window: "iCal can't
-
Hello there, I have noticed recently that my early 2011, 15" Macbook Pro no longer goes to sleep when I close the lid, or when I select sleep in the Apple menu. When I close the lid or select sleep, the screen turns off, but I am still able to hear t
-
I am wondering if Apple can help me in case my iPad was stolen?
Two weeks ago my iPad was stolen from my appartment. I try to block it using Find my iPhone service but it is useless because they switched off the geolocation service. I only got the message today that my iPad was eventually blocked but still do not
-
i have recently upgraded my itunes to version 6 or whatever is the latest. after i had done this i decided to upgrade the software on the computer using the 'software update' option. little did i know, the updater updated my itunes. this is a second