Server 2012 R2 DHCP Failover - Hot Standby clients not renewing with standby server

In my test network I have a pair of Server 2012 R2 DHCP servers setup for Hot Standby and they will successfully service a client request for a new request. 
What I am seeing is that when I test failover the clients will not renew with the Standby server. I have to release first and then renew. 
When both DHCP servers are up the state is normal and replication of configuration from the Active to Standby is working. As far as I can tell it is configured correctly. 
MaxClientLeadTime is 10 minutes. 
StateSwitchInterval is 10 minutes. 
AutoStateTransition is set to True. 
Adding that manual renews fail with a message stating that it was unable to contact the dhcp server. However if I wait for the lease to expire/auto-renew the dhcp server does indeed change to the standby. Once the primary server comes back up and the state
returns to normal I am able to manually renew. 
thanks in advance


Hi,
For test, we let the active DHCP down and the standby DHCP server will take place. But when we renew an IP, client send unicast to the former DHCP
server. That’s why the first request failed.
At 7/8 of the scope lease time, the client moves into a REBINDING state and broadcasts a lease renewal request.
For more information please refer to:
DHCP Failover Examples
http://technet.microsoft.com/en-us/library/dn338973.aspx
Hope this helps.

Similar Messages

  • WSUS Windows 7 Client not connecting with WSUS SERVER 2012 R2 Error " 80072ee2"

    Hi ,
            I Have the Non- AD WSUS server 2012 R2 as WSUS server, and widnows 7 ent sp1 as WSUS Client  , the server and client are in teh same ip range and able to ping both server from client and client from server, and both are in teh
    same time zone(EST), But im getting the "80072ee2" when ever i tried to get the updates from client
    Please help me on this
    Thanks 
    Balaji K

    Record the system time of the Windows 7 client.
    Reboot the Windows 7 client.
    Run this command from a command prompt: wuauclt /resetauthorization /detectnow.
    Wait =30= minutes.
    Post the entries from the WindowsUpdate.log starting at the time recorded in Step #1.
    I have noted the time at 12:06 am and reboot the machine. and at 12:27 i have Run this command from a 
    command prompt: wuauclt /resetauthorization /detectnow. and taken the the logs from 11 am to 1 pm 
    2015-02-03 12:15:26:002
    956 f84
    Misc WARNING: Send failed with hr = 80072ee2.
    2015-02-03 12:15:26:002
    956 f84
    Misc WARNING: SendRequest failed with hr = 80072ee2. Proxy List used: <(null)> Bypass List used : <(null)> Auth Schemes used : <>
    2015-02-03 12:15:26:002
    956 f84
    PT  + Last proxy send request failed with hr = 0x80072EE2, HTTP status code = 0
    2015-02-03 12:15:26:002
    956 f84
    PT  + Caller provided credentials = No
    2015-02-03 12:15:26:002
    956 f84
    PT  + Impersonate flags = 0
    2015-02-03 12:15:26:002
    956 f84
    PT  + Possible authorization schemes used = 
    2015-02-03 12:15:26:002
    956 f84
    PT WARNING: GetConfig failure, error = 0x80072EE2, soap client error = 5, soap error code = 0, HTTP status code = 200
    2015-02-03 12:15:26:002
    956 f84
    PT WARNING: PTError: 0x80072ee2
    2015-02-03 12:15:26:002
    956 f84
    PT WARNING: GetConfig_WithRecovery failed: 0x80072ee2
    2015-02-03 12:15:26:002
    956 f84
    PT WARNING: RefreshConfig failed: 0x80072ee2
    2015-02-03 12:15:26:002
    956 f84
    PT WARNING: RefreshPTState failed: 0x80072ee2
    2015-02-03 12:15:26:002
    956 f84
    PT WARNING: PTError: 0x80072ee2
    2015-02-03 12:15:26:002
    956 f84
    Report WARNING: Reporter failed to upload events with hr = 80072ee2.
    2015-02-03 12:27:05:651
    956 ca8
    AU Triggering AU detection through DetectNow API
    2015-02-03 12:27:05:651
    956 ca8
    AU Triggering Online detection (non-interactive)
    2015-02-03 12:27:05:652
    956 930
    AU #############
    2015-02-03 12:27:05:652
    956 930
    AU ## START ##  AU: Search for updates
    2015-02-03 12:27:05:652
    956 930
    AU #########
    2015-02-03 12:27:05:654
    956 930
    AU <<## SUBMITTED ## AU: Search for updates [CallId = {710EE50A-0397-4DC8-B33B-B97410B73C00}]
    2015-02-03 12:27:05:654
    956 f84
    Agent *************
    2015-02-03 12:27:05:654
    956 f84
    Agent ** START **  Agent: Finding updates [CallerId = AutomaticUpdates]
    2015-02-03 12:27:05:654
    956 f84
    Agent *********
    2015-02-03 12:27:05:654
    956 f84
    Agent  * Online = Yes; Ignore download priority = No
    2015-02-03 12:27:05:654
    956 f84
    Agent  * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation' or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0
    and DeploymentAction='Uninstallation' and RebootRequired=1"
    2015-02-03 12:27:05:654
    956 f84
    Agent  * ServiceID = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7} Managed
    2015-02-03 12:27:05:654
    956 f84
    Agent  * Search Scope = {Machine}
    2015-02-03 12:27:05:678
    956 f84
    Setup Checking for agent SelfUpdate
    2015-02-03 12:27:05:678
    956 f84
    Setup Client version: Core: 7.5.7601.17514  Aux: 7.5.7601.17514
    2015-02-03 12:27:29:233
    956 f84
    Misc WARNING: Send failed with hr = 80072ee2.
    2015-02-03 12:27:29:233
    956 f84
    Misc WARNING: SendRequest failed with hr = 80072ee2. Proxy List used: <(null)> Bypass List used : <(null)> Auth Schemes used : <>
    2015-02-03 12:27:29:233
    956 f84
    Misc WARNING: WinHttp: SendRequestUsingProxy failed for <http://135.155.61.172:8530/selfupdate/wuident.cab>. error 0x80072ee2
    2015-02-03 12:27:29:234
    956 f84
    Misc WARNING: WinHttp: SendRequestToServerForFileInformation MakeRequest failed. error 0x80072ee2
    2015-02-03 12:27:29:234
    956 f84
    Misc WARNING: WinHttp: SendRequestToServerForFileInformation failed with 0x80072ee2
    2015-02-03 12:27:29:234
    956 f84
    Misc WARNING: WinHttp: ShouldFileBeDownloaded failed with 0x80072ee2
    2015-02-03 12:27:52:795
    956 f84
    Misc WARNING: Send failed with hr = 80072ee2.
    2015-02-03 12:27:52:795
    956 f84
    Misc WARNING: SendRequest failed with hr = 80072ee2. Proxy List used: <(null)> Bypass List used : <(null)> Auth Schemes used : <>
    2015-02-03 12:27:52:795
    956 f84
    Misc WARNING: WinHttp: SendRequestUsingProxy failed for <http://135.155.61.172:8530/selfupdate/wuident.cab>. error 0x80072ee2
    2015-02-03 12:27:52:796
    956 f84
    Misc WARNING: WinHttp: SendRequestToServerForFileInformation MakeRequest failed. error 0x80072ee2
    2015-02-03 12:27:52:796
    956 f84
    Misc WARNING: WinHttp: SendRequestToServerForFileInformation failed with 0x80072ee2
    2015-02-03 12:27:52:796
    956 f84
    Misc WARNING: WinHttp: ShouldFileBeDownloaded failed with 0x80072ee2
    2015-02-03 12:28:16:363
    956 f84
    Misc WARNING: Send failed with hr = 80072ee2.
    2015-02-03 12:28:16:363
    956 f84
    Misc WARNING: SendRequest failed with hr = 80072ee2. Proxy List used: <(null)> Bypass List used : <(null)> Auth Schemes used : <>
    2015-02-03 12:28:16:364
    956 f84
    Misc WARNING: WinHttp: SendRequestUsingProxy failed for <http://135.155.61.172:8530/selfupdate/wuident.cab>. error 0x80072ee2
    2015-02-03 12:28:16:364
    956 f84
    Misc WARNING: WinHttp: SendRequestToServerForFileInformation MakeRequest failed. error 0x80072ee2
    2015-02-03 12:28:16:364
    956 f84
    Misc WARNING: WinHttp: SendRequestToServerForFileInformation failed with 0x80072ee2
    2015-02-03 12:28:16:364
    956 f84
    Misc WARNING: WinHttp: ShouldFileBeDownloaded failed with 0x80072ee2
    2015-02-03 12:28:39:920
    956 f84
    Misc WARNING: Send failed with hr = 80072ee2.
    2015-02-03 12:28:39:920
    956 f84
    Misc WARNING: SendRequest failed with hr = 80072ee2. Proxy List used: <(null)> Bypass List used : <(null)> Auth Schemes used : <>
    2015-02-03 12:28:39:920
    956 f84
    Misc WARNING: WinHttp: SendRequestUsingProxy failed for <http://135.155.61.172:8530/selfupdate/wuident.cab>. error 0x80072ee2
    2015-02-03 12:28:39:921
    956 f84
    Misc WARNING: WinHttp: SendRequestToServerForFileInformation MakeRequest failed. error 0x80072ee2
    2015-02-03 12:28:39:921
    956 f84
    Misc WARNING: WinHttp: SendRequestToServerForFileInformation failed with 0x80072ee2
    2015-02-03 12:28:39:921
    956 f84
    Misc WARNING: WinHttp: ShouldFileBeDownloaded failed with 0x80072ee2
    2015-02-03 12:28:39:921
    956 f84
    Misc WARNING: DownloadFileInternal failed for http://135.155.61.172:8530/selfupdate/wuident.cab: error 0x80072ee2
    2015-02-03 12:28:39:921
    956 f84
    Setup WARNING: SelfUpdate check failed to download package information, error = 0x80072EE2
    2015-02-03 12:28:39:921
    956 f84
    Setup FATAL: SelfUpdate check failed, err = 0x80072EE2
    2015-02-03 12:28:39:922
    956 f84
    Agent  * WARNING: Skipping scan, self-update check returned 0x80072EE2
    2015-02-03 12:28:39:923
    956 f84
    Agent  * WARNING: Exit code = 0x80072EE2
    2015-02-03 12:28:39:923
    956 f84
    Agent *********
    2015-02-03 12:28:39:923
    956 f84
    Agent **  END  **  Agent: Finding updates [CallerId = AutomaticUpdates]
    2015-02-03 12:28:39:923
    956 f84
    Agent *************
    2015-02-03 12:28:39:923
    956 f84
    Agent WARNING: WU client failed Searching for update with error 0x80072ee2
    2015-02-03 12:28:39:924
    956 fec
    AU >>##  RESUMED  ## AU: Search for updates [CallId = {710EE50A-0397-4DC8-B33B-B97410B73C00}]
    2015-02-03 12:28:39:924
    956 fec
    AU  # WARNING: Search callback failed, result = 0x80072EE2
    2015-02-03 12:28:39:924
    956 fec
    AU  # WARNING: Failed to find updates with error code 80072EE2
    2015-02-03 12:28:39:924
    956 fec
    AU #########
    2015-02-03 12:28:39:924
    956 fec
    AU ##  END  ##  AU: Search for updates [CallId = {710EE50A-0397-4DC8-B33B-B97410B73C00}]
    2015-02-03 12:28:39:924
    956 fec
    AU #############
    2015-02-03 12:28:39:925
    956 fec
    AU Successfully wrote event for AU health state:0
    2015-02-03 12:28:39:925
    956 fec
    AU AU setting next detection timeout to 2015-02-03 21:23:35
    2015-02-03 12:28:39:926
    956 fec
    AU Successfully wrote event for AU health state:0
    2015-02-03 12:28:39:928
    956 fec
    AU Successfully wrote event for AU health state:0
    2015-02-03 12:29:03:495
    956 f84
    Misc WARNING: Send failed with hr = 80072ee2.
    2015-02-03 12:29:03:495
    956 f84
    Misc WARNING: SendRequest failed with hr = 80072ee2. Proxy List used: <(null)> Bypass List used : <(null)> Auth Schemes used : <>
    2015-02-03 12:29:03:496
    956 f84
    PT  + Last proxy send request failed with hr = 0x80072EE2, HTTP status code = 0
    2015-02-03 12:29:03:496
    956 f84
    PT  + Caller provided credentials = No
    2015-02-03 12:29:03:496
    956 f84
    PT  + Impersonate flags = 0
    2015-02-03 12:29:03:496
    956 f84
    PT  + Possible authorization schemes used = 
    2015-02-03 12:29:03:496
    956 f84
    PT WARNING: GetConfig failure, error = 0x80072EE2, soap client error = 5, soap error code = 0, HTTP status code = 200
    2015-02-03 12:29:03:496
    956 f84
    PT WARNING: PTError: 0x80072ee2
    2015-02-03 12:29:03:496
    956 f84
    PT WARNING: GetConfig_WithRecovery failed: 0x80072ee2
    2015-02-03 12:29:03:496
    956 f84
    PT WARNING: RefreshConfig failed: 0x80072ee2
    2015-02-03 12:29:03:496
    956 f84
    PT WARNING: RefreshPTState failed: 0x80072ee2
    2015-02-03 12:29:03:496
    956 f84
    PT WARNING: PTError: 0x80072ee2
    2015-02-03 12:29:03:496
    956 f84
    Report WARNING: Reporter failed to upload events with hr = 80072ee2.
    2015-02-03 12:29:03:496
    956 f84
    Report REPORT EVENT: {B6636CDB-B0BF-4CDE-BEB3-D49C1CEC258F}
    2015-02-03 12:28:39:921-0800 1
    148 101
    {D67661EB-2423-451D-BF5D-13199E37DF28}
    1 80072ee2
    SelfUpdate Failure
    Software Synchronization Windows Update Client failed to detect with error 0x80072ee2.
    2015-02-03 12:29:03:510
    956 f84
    Report CWERReporter::HandleEvents - WER report upload completed with status 0x8
    2015-02-03 12:29:03:510
    956 f84
    Report WER Report sent: 7.5.7601.17514 0x80072ee2 D67661EB-2423-451D-BF5D-13199E37DF28 Scan 101 Managed
    2015-02-03 12:29:03:510
    956 f84
    Report CWERReporter finishing event handling. (00000000)
    2015-02-03 12:29:27:075
    956 f84
    Misc WARNING: Send failed with hr = 80072ee2.
    2015-02-03 12:29:27:075
    956 f84
    Misc WARNING: SendRequest failed with hr = 80072ee2. Proxy List used: <(null)> Bypass List used : <(null)> Auth Schemes used : <>
    2015-02-03 12:29:27:075
    956 f84
    PT  + Last proxy send request failed with hr = 0x80072EE2, HTTP status code = 0
    2015-02-03 12:29:27:075
    956 f84
    PT  + Caller provided credentials = No
    2015-02-03 12:29:27:075
    956 f84
    PT  + Impersonate flags = 0
    2015-02-03 12:29:27:075
    956 f84
    PT  + Possible authorization schemes used = 
    2015-02-03 12:29:27:075
    956 f84
    PT WARNING: GetConfig failure, error = 0x80072EE2, soap client error = 5, soap error code = 0, HTTP status code = 200
    2015-02-03 12:29:27:075
    956 f84
    PT WARNING: PTError: 0x80072ee2
    2015-02-03 12:29:27:076
    956 f84
    PT WARNING: GetConfig_WithRecovery failed: 0x80072ee2
    2015-02-03 12:29:27:076
    956 f84
    PT WARNING: RefreshConfig failed: 0x80072ee2
    2015-02-03 12:29:27:076
    956 f84
    PT WARNING: RefreshPTState failed: 0x80072ee2
    2015-02-03 12:29:27:076
    956 f84
    PT WARNING: PTError: 0x80072ee2
    2015-02-03 12:29:27:076
    956 f84
    Report WARNING: Reporter failed to upload events with hr = 80072ee2.
    2015-02-03 12:53:05:793
    956 930
    AU AU received policy change subscription event
    2015-02-03 12:58:26:707
    956 8fc
    Misc WARNING: Send failed with hr = 80072ee2.
    2015-02-03 12:58:26:707
    956 8fc
    Misc WARNING: SendRequest failed with hr = 80072ee2. Proxy List used: <(null)> Bypass List used : <(null)> Auth Schemes used : <>
    2015-02-03 12:58:26:708
    956 8fc
    PT  + Last proxy send request failed with hr = 0x80072EE2, HTTP status code = 0
    2015-02-03 12:58:26:708
    956 8fc
    PT  + Caller provided credentials = No
    2015-02-03 12:58:26:708
    956 8fc
    PT  + Impersonate flags = 0
    2015-02-03 12:58:26:708
    956 8fc
    PT  + Possible authorization schemes used = 
    2015-02-03 12:58:26:708
    956 8fc
    PT WARNING: GetConfig failure, error = 0x80072EE2, soap client error = 5, soap error code = 0, HTTP status code = 200
    2015-02-03 12:58:26:708
    956 8fc
    PT WARNING: PTError: 0x80072ee2
    2015-02-03 12:58:26:708
    956 8fc
    PT WARNING: GetConfig_WithRecovery failed: 0x80072ee2
    2015-02-03 12:58:26:708
    956 8fc
    PT WARNING: RefreshConfig failed: 0x80072ee2
    2015-02-03 12:58:26:708
    956 8fc
    PT WARNING: RefreshPTState failed: 0x80072ee2
    2015-02-03 12:58:26:708
    956 8fc
    PT WARNING: PTError: 0x80072ee2
    2015-02-03 12:58:26:708
    956 8fc
    Report WARNING: Reporter failed to upload events with hr = 80072ee2.

  • ORA-16191: Primary log shipping client not logged on standby.

    Hi,
    Please help me in the following scenario. I have two nodes ASM1 & ASM2 with RHEL4 U5 OS. On node ASM1 there is database ORCL using ASM diskgroups DATA & RECOVER and archive location is on '+RECOVER/orcl/'. On ASM2 node, I have to configure STDBYORCL (standby) database using ASM. I have taken the copy of database ORCL via RMAN, as per maximum availability architecture.
    Then I have ftp'd all to ASM2 and put them on FS /u01/oradata. Have made all necessary changes in primary and standby database pfile and then perform the duplicate database for standby using RMAN in order to put the db files in desired diskgroups. I have mounted the standby database but unfortunately, log transport service is not working and archives are not getting shipped to standby host.
    Here are all configuration details.
    Primary database ORCL pfile:
    [oracle@asm dbs]$ more initorcl.ora
    stdbyorcl.__db_cache_size=251658240
    orcl.__db_cache_size=226492416
    stdbyorcl.__java_pool_size=4194304
    orcl.__java_pool_size=4194304
    stdbyorcl.__large_pool_size=4194304
    orcl.__large_pool_size=4194304
    stdbyorcl.__shared_pool_size=100663296
    orcl.__shared_pool_size=125829120
    stdbyorcl.__streams_pool_size=0
    orcl.__streams_pool_size=0
    *.audit_file_dest='/opt/oracle/admin/orcl/adump'
    *.background_dump_dest='/opt/oracle/admin/orcl/bdump'
    *.compatible='10.2.0.1.0'
    *.control_files='+DATA/orcl/controlfile/current.270.665007729','+RECOVER/orcl/controlfile/current.262.665007731'
    *.core_dump_dest='/opt/oracle/admin/orcl/cdump'
    *.db_block_size=8192
    *.db_create_file_dest='+DATA'
    *.db_domain=''
    *.db_file_multiblock_read_count=16
    *.db_name='orcl'
    *.db_recovery_file_dest='+RECOVER'
    *.db_recovery_file_dest_size=3163553792
    *.db_unique_name=orcl
    *.fal_client=orcl
    *.fal_server=stdbyorcl
    *.instance_name='orcl'
    *.job_queue_processes=10
    *.log_archive_config='dg_config=(orcl,stdbyorcl)'
    *.log_archive_dest_1='LOCATION=USE_DB_RECOVERY_FILE_DEST'
    *.log_archive_dest_2='SERVICE=stdbyorcl'
    *.log_archive_dest_state_1='ENABLE'
    *.log_archive_dest_state_2='ENABLE'
    *.log_archive_format='%t_%s_%r.dbf'
    *.open_cursors=300
    *.pga_aggregate_target=121634816
    *.processes=150
    *.remote_login_passwordfile='EXCLUSIVE'
    *.sga_target=364904448
    *.standby_file_management='AUTO'
    *.undo_management='AUTO'
    *.undo_tablespace='UNDOTBS'
    *.user_dump_dest='/opt/oracle/admin/orcl/udump'
    Standby database STDBYORCL pfile:
    [oracle@asm2 dbs]$ more initstdbyorcl.ora
    stdbyorcl.__db_cache_size=251658240
    stdbyorcl.__java_pool_size=4194304
    stdbyorcl.__large_pool_size=4194304
    stdbyorcl.__shared_pool_size=100663296
    stdbyorcl.__streams_pool_size=0
    *.audit_file_dest='/opt/oracle/admin/stdbyorcl/adump'
    *.background_dump_dest='/opt/oracle/admin/stdbyorcl/bdump'
    *.compatible='10.2.0.1.0'
    *.control_files='u01/oradata/stdbyorcl_control01.ctl'#Restore Controlfile
    *.core_dump_dest='/opt/oracle/admin/stdbyorcl/cdump'
    *.db_block_size=8192
    *.db_create_file_dest='/u01/oradata'
    *.db_domain=''
    *.db_file_multiblock_read_count=16
    *.db_name='orcl'
    *.db_recovery_file_dest='+RECOVER'
    *.db_recovery_file_dest_size=3163553792
    *.db_unique_name=stdbyorcl
    *.fal_client=stdbyorcl
    *.fal_server=orcl
    *.instance_name='stdbyorcl'
    *.job_queue_processes=10
    *.log_archive_config='dg_config=(orcl,stdbyorcl)'
    *.log_archive_dest_1='LOCATION=USE_DB_RECOVERY_FILE_DEST'
    *.log_archive_dest_2='SERVICE=orcl'
    *.log_archive_dest_state_1='ENABLE'
    *.log_archive_dest_state_2='ENABLE'
    *.log_archive_format='%t_%s_%r.dbf'
    *.log_archive_start=TRUE
    *.open_cursors=300
    *.pga_aggregate_target=121634816
    *.processes=150
    *.remote_login_passwordfile='EXCLUSIVE'
    *.sga_target=364904448
    *.standby_archive_dest='LOCATION=USE_DB_RECOVERY_FILE_DEST'
    *.standby_file_management='AUTO'
    *.undo_management='AUTO'
    *.undo_tablespace='UNDOTBS'
    *.user_dump_dest='/opt/oracle/admin/stdbyorcl/udump'
    db_file_name_convert=('+DATA/ORCL/DATAFILE','/u01/oradata','+RECOVER/ORCL/DATAFILE','/u01/oradata')
    log_file_name_convert=('+DATA/ORCL/ONLINELOG','/u01/oradata','+RECOVER/ORCL/ONLINELOG','/u01/oradata')
    Have configured the tns service on both the hosts and its working absolutely fine.
    <p>
    ASM1
    =====
    [oracle@asm dbs]$ tnsping stdbyorcl
    </p>
    <p>
    TNS Ping Utility for Linux: Version 10.2.0.1.0 - Production on 19-SEP-2008 18:49:00
    </p>
    <p>
    Copyright (c) 1997, 2005, Oracle. All rights reserved.
    </p>
    <p>
    Used parameter files:
    </p>
    <p>
    Used TNSNAMES adapter to resolve the alias
    Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.20)(PORT = 1521))) (CONNECT_DATA = (SID = stdbyorcl) (SERVER = DEDICATED)))
    OK (30 msec)
    ASM2
    =====
    </p>
    <p>
    [oracle@asm2 archive]$ tnsping orcl
    </p>
    <p>
    TNS Ping Utility for Linux: Version 10.2.0.1.0 - Production on 19-SEP-2008 18:48:39
    </p>
    <p>
    Copyright (c) 1997, 2005, Oracle. All rights reserved.
    </p>
    <p>
    Used parameter files:
    </p>
    <p>
    Used TNSNAMES adapter to resolve the alias
    Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.10)(PORT = 1521))) (CONNECT_DATA = (SID = orcl) (SERVER = DEDICATED)))
    OK (30 msec)
    Please guide where I am missing. Thanking you in anticipation.
    Regards,
    Ravish Garg

    Following are the errors I am receiving as per alert log.
    ORCL alert log:
    Thu Sep 25 17:49:14 2008
    ARCH: Possible network disconnect with primary database
    Thu Sep 25 17:49:14 2008
    Error 1031 received logging on to the standby
    Thu Sep 25 17:49:14 2008
    Errors in file /opt/oracle/admin/orcl/bdump/orcl_arc1_4825.trc:
    ORA-01031: insufficient privileges
    FAL[server, ARC1]: Error 1031 creating remote archivelog file 'STDBYORCL'
    FAL[server, ARC1]: FAL archive failed, see trace file.
    Thu Sep 25 17:49:14 2008
    Errors in file /opt/oracle/admin/orcl/bdump/orcl_arc1_4825.trc:
    ORA-16055: FAL request rejected
    ARCH: FAL archive failed. Archiver continuing
    Thu Sep 25 17:49:14 2008
    ORACLE Instance orcl - Archival Error. Archiver continuing.
    Thu Sep 25 17:49:44 2008
    FAL[server]: Fail to queue the whole FAL gap
    GAP - thread 1 sequence 40-40
    DBID 1192788465 branch 665007733
    Thu Sep 25 17:49:46 2008
    Thread 1 advanced to log sequence 48
    Current log# 2 seq# 48 mem# 0: +DATA/orcl/onlinelog/group_2.272.665007735
    Current log# 2 seq# 48 mem# 1: +RECOVER/orcl/onlinelog/group_2.264.665007737
    Thu Sep 25 17:55:43 2008
    Shutting down archive processes
    Thu Sep 25 17:55:48 2008
    ARCH shutting down
    ARC2: Archival stopped
    STDBYORCL alert log:
    ==============
    Thu Sep 25 17:49:27 2008
    Errors in file /opt/oracle/admin/stdbyorcl/bdump/stdbyorcl_arc0_4813.trc:
    ORA-01017: invalid username/password; logon denied
    Thu Sep 25 17:49:27 2008
    Error 1017 received logging on to the standby
    Check that the primary and standby are using a password file
    and remote_login_passwordfile is set to SHARED or EXCLUSIVE,
    and that the SYS password is same in the password files.
    returning error ORA-16191
    It may be necessary to define the DB_ALLOWED_LOGON_VERSION
    initialization parameter to the value "10". Check the
    manual for information on this initialization parameter.
    Thu Sep 25 17:49:27 2008
    Errors in file /opt/oracle/admin/stdbyorcl/bdump/stdbyorcl_arc0_4813.trc:
    ORA-16191: Primary log shipping client not logged on standby
    PING[ARC0]: Heartbeat failed to connect to standby 'orcl'. Error is 16191.
    Thu Sep 25 17:51:38 2008
    FAL[client]: Failed to request gap sequence
    GAP - thread 1 sequence 40-40
    DBID 1192788465 branch 665007733
    FAL[client]: All defined FAL servers have been attempted.
    Check that the CONTROL_FILE_RECORD_KEEP_TIME initialization
    parameter is defined to a value that is sufficiently large
    enough to maintain adequate log switch information to resolve
    archivelog gaps.
    Thu Sep 25 17:55:16 2008
    Errors in file /opt/oracle/admin/stdbyorcl/bdump/stdbyorcl_arc0_4813.trc:
    ORA-01017: invalid username/password; logon denied
    Thu Sep 25 17:55:16 2008
    Error 1017 received logging on to the standby
    Check that the primary and standby are using a password file
    and remote_login_passwordfile is set to SHARED or EXCLUSIVE,
    and that the SYS password is same in the password files.
    returning error ORA-16191
    It may be necessary to define the DB_ALLOWED_LOGON_VERSION
    initialization parameter to the value "10". Check the
    manual for information on this initialization parameter.
    Thu Sep 25 17:55:16 2008
    Errors in file /opt/oracle/admin/stdbyorcl/bdump/stdbyorcl_arc0_4813.trc:
    ORA-16191: Primary log shipping client not logged on standby
    PING[ARC0]: Heartbeat failed to connect to standby 'orcl'. Error is 16191.
    Please suggest where I am missing.
    Regards,
    Ravish Garg

  • Regarding mountain lion server: clients experience intermittent service connections. the server system log has the following error- Client handshake failed (6):113: Server not accepting client connections (any ideas???)

    regarding mountain lion server: clients experience intermittent service connections. the server system log has the following error- Client handshake failed (6):113: Server not accepting client connections. any suggestions would be greatly appreciated - thank you

    Hi Jason
    I was getting the same behavior after Apple support had me delete some plist files to get Airplay going. I was also getting the following error:
    the error occurred while processing a command of type 'writesettings' in the plug-in 'server vpn'
    I went into ~/Library/Preferences/ and /Library/Preferences/ and deleted every plist contating the word server. I had to re-set up my server (meaning walk through some intial steps) but all of my settings were still there after that and everything started working again.
    Just a thought, obviously try at your own risk but it worked for me.
    Kellen

  • A project which specifies SQL Server 2012 as the target platform may experience compatibility issues with Microsoft Azure SQL Database.

    Hello
    When I try to publis my asp.net application in azure, i have the next error:
    >C:\Program Files (x86)\MSBuild\Microsoft\VisualStudio\v12.0\Web\Microsoft.Web.Publishing.targets(4253,5): Warning : A project which specifies SQL Server 2012 as the target platform may experience compatibility issues with Microsoft Azure SQL Database.
    >C:\Program Files (x86)\MSBuild\Microsoft\VisualStudio\v12.0\Web\Microsoft.Web.Publishing.targets(4253,5): Warning : The project and target databases have different collation settings. Deployment errors might occur.

    Hello
    When I try to publis my asp.net application in azure, i have the next error:
    >C:\Program Files (x86)\MSBuild\Microsoft\VisualStudio\v12.0\Web\Microsoft.Web.Publishing.targets(4253,5): Warning : A project which specifies SQL Server 2012 as the target platform may experience compatibility issues with Microsoft Azure SQL Database.
    >C:\Program Files (x86)\MSBuild\Microsoft\VisualStudio\v12.0\Web\Microsoft.Web.Publishing.targets(4253,5): Warning : The project and target databases have different collation settings. Deployment errors might occur.
    Hello,
    This forum is to discuss vb.net issues, your issue is mainly regarding Azure SQL Database, I found that you have posted another thread in that forum
    https://social.msdn.microsoft.com/Forums/azure/en-US/f435921a-14d1-4441-8b2b-32ba3d937aea/a-project-which-specifies-sql-server-2012-as-the-target-platform-may-experience-compatibility-issues?forum=ssdsgetstarted#f435921a-14d1-4441-8b2b-32ba3d937aea.
    I would recommend you focus on that thread to get help.
    Regards,
    Carl
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • The crawler could not communicate with the server.

    valmiki

    Hi,
    According to your post, my understanding is that you get an error when communicating to the server.
      1.  This happens when crawler is not able to connect to the server. Make sure server name is correct and your crawl account should have the Full Read permission on the User Policy at the Web Application level.  It should not have any specific
    permission on any site collection.
    Couple of steps to troubleshoot it:
      a. You should be able to ping the server from the server having crawl component. Make sure there is an entry for the server in the host file under c:\Windows\System32\drivers\etc folder.
          Ping <servername>
      b.  You should be able to connect to the server using telnet command
          Telnet< servername> <port number>
    https://social.technet.microsoft.com/Forums/en-US/01b6cdda-ca38-46c1-be07-2e89eb91271f/the-crawler-could-not-communicate-with-the-server-check-that-the-server-is-available-and-that-the?forum=sharepointsearchprevious
      2.  Can you browse to the WebApp from the server that is performing the Crawl? The issue is usually the most typical is the LoopBackCheck.
    Click Start, click Run, type regedit, and then click OK.
    In Registry Editor, locate and then click the following registry key:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa\MSV1_0
    Right-click MSV1_0, point to New, and then click Multi-String Value.
    Type BackConnectionHostNames, and then press ENTER.
    Right-click BackConnectionHostNames, and then click  Modify.
    In the Value data box, type the host name or the host names for the sites that are on the local  computer, and then click OK.
    Quit Registry Editor, and then restart the IISAdmin service.
    https://social.technet.microsoft.com/Forums/en-US/f378c45f-fa8b-48f3-88bb-739f3cd27830/the-crawler-could-not-communicate-with-the-server-check-that-the-server-is-available-and-that-the?forum=sharepointadminprevious
      3.  Checked WinProxy to see configured proxy:
           C:\Windows\system32>NetSH WinHTTP Show Proxy
           Run NetSH WinHTTP Reset Proxy
           Restart server and test again.
    https://social.technet.microsoft.com/Forums/en-US/1baa6fd5-acc7-4cda-b7cb-7fa86aa8101f/the-crawler-could-not-communicate-with-the-server?forum=sharepointsearchprevious
      4.  The web.config file of the crawled web application contains an error.
           The target site collection contains a web part error for instance on the default.aspx.
           Also check the solution are not deployed correctly.Central Administration -> Solution Management (Manage Farm Solutions).
    https://sharepointsriram.wordpress.com/2011/12/10/the-crawler-could-not-communicate-with-the-server-check-that-the-server-is-available-and-that-the-firewall-access-is-configured-correctly/
    If the issue still exists, you can try to delete the old search application and recreate from the beginning.
    You can also reset the index and do a full crawl after.
    For more information about this similar issue, you can refer to:
    http://sharepointroot.com/2012/03/16/sharepoint-search-the-crawler-could-not-communicate-with-the-server/
    http://www.sharepointed.com/2013/08/13/the-crawler-could-not-communicate-with-the-server-check-that-the-server-is-available-and-that-the-firewall-access-is-configured-correctly/
    http://www.information-worker.nl/2011/01/11/the-crawler-could-not-communicate-with-the-server/
    https://social.technet.microsoft.com/Forums/en-US/0e7ffd07-c584-4767-a2bc-ce3a014255c6/the-crawler-could-not-communicate-with-the-server-check-that-the-server-is-available-and-that-the?forum=sharepointadminprevious
    Best Regards,
    Yumi Fu

  • I bought a new imac running Loin and Office 2011. The server we use to access emails runs exchange 2003 and my IT person says the imac is not compatible with the server. The server does not want to let me access using any email software.

    I bought a new imac running Loin with Office 2011. I am the only mac in the office and the Server we use to access emails runs exchange 2003 and my IT person says the imac is not compatible with the server. The server does not want to let me access using any email software other than webmail access through our website. It looks as though 2011 is not compatible with 2003 per some searches online, but what are some options I have to gain full access again? I purchased parallels in hopes that this my help and I am able to use remote desktop connection to log on to server but can not drag and drop files I need. There is a shared drive on that Server we all use to exchange files.
    The two main issues are gaining access to my email again and ability to drag and drop files from mac to pc. I hope this is enough info to get some solutions.
    PS - IT person says my iMac's IP is what his server does not understand so that is why I can not login.

    Office 2011 is not compatbile with Exchange 2003.
    I suggest you post further Office related questions on Microsoft's own forums for their Mac software:
    http://answers.microsoft.com/en-us/mac

  • Add does not run with sql server 2008

    Hi all,
    My add on in the development environment does not run with SQL SERVER 2008. It ran well with SQL Server 2005 and sap b1 2207 B.
    On executing the project file system throws an error "YOU ARE NOT CONNECTED TO THE COMPANY"
    we are trying this scenario on a test machine where SAP B1 2007B with temporary license for one month and SQL server 2008
    is installed.
    Help needed.
    Thanking you
    Pradnya

    Hi Use this
    Dim i as integer
    i=oCompany.Connect()
    if i<> 0 Then
    msgbox(ocompany.GetLastErrorDescription ())
    end if
    the you will get the error description also use try catch wherever necessary
    Alternatively you can use
    Dim SboGuiApi As SAPbouiCOM.SboGuiApi
    Dim sConnectionString As String
    Set SboGuiApi = New SAPbouiCOM.SboGuiApi
    sConnectionString = Command
    SboGuiApi.Connect sConnectionString
    Set SBO_Application = SboGuiApi.GetApplication()
    Set ocompany = New SAPbobsCOM.Company 'initialate DI company object
      ocompany = SBO_Application.Company.GetDICompany
    HTH,
    Atul

  • Calendar will not sync with Exchange server or most Google Calendars

    Hi,
    I am writing about my wife's brand new Samsung Charge on Verizon. We managed to setup both her gmail account and her work exchange server account fine, except for the calendars:
    Her Google calendar shows up fine, but I am unable to even see any other Google calendars that she has access to (both her own secondary calendars as well as calendars that others have shared with her) in order to select them to be visible.
    Her exchange calendar says it is enabled (on the list of available calendars), but no events at all show up.
    This behavior is with the latest software updates on the Charge (2.2.1 firmware, I510.EE4 build) using its stock calendar software. I did notice that if I use Smooth Calendar, it does list all of her Google calendars under its listing of available calendars, but it still only shows data from her primary calendar. This is also true using the Touch Calendar app, which leads me to believe that there is some problem within the Google Calendar sync software that is not allowing her calendars to appear correctly.
    Thanks!

    Hello whereizben,
    I see you have posted same post in another thread.  I have already replied to that posting with a solution.  Please see the following link for my reply:
    Re: Calendar will not sync with Exchange Server
    Thanks, again, for posting!

  • The crawler could not communicate with the server. Check that the server is available and that the firewall access is configured correctly. If the repository was temporarily unavailable, an incremental crawl will fix this error

    We are getting the below error when we see in Crawl logs
    "The crawler could not communicate with the server. Check that the server is available and that the firewall access is configured correctly. If the repository was temporarily unavailable, an incremental crawl will fix this error."
    This is happening in FAST search.
    Here I can see soke of the logs related to this search crawl.
    Could anyone please help on this?
    web application 'http://xvy/' doesn't use search application 'FAST Query SSA', skipping it.
    ABC\sp_search' on web application 'http://xvy/'. 2d7dba01-3d2e-4903-b59f-9a8601627bcd
    07/30/2014 01:30:46.65  OWSTIMER.EXE (0x28DC)                    0x1BC0 SharePoint Server Search       Administration               
     dl2m Verbose  Search application 'Search Service Application 1': Skipping web application '48ed7882-9f70-424e-bf72-e3c9f5340b97' because its outbound url 'http://ebc:30347' was automatically added once.
    Ensure full read access to the indexing account 'ABC\sp_search' on web application 'http://nvcp/'. 85041609-d618-4132-ac8e-195a910d99a0
    07/30/2014 01:31:46.53  OWSTIMER.EXE (0x28DC)                    0x05F4 SharePoint Server Search       Administration               
     dl2m Verbose  Search application 'FAST Query SSA': Skipping web application '57718ea1-8cb5-4adc-abd2-9e55415e5791' because its outbound url 'http://nvcp' was automatically added once. 85041609-d618-4132-ac8e-195a910d99a0
    07/30/2014 01:31:46.53  OWSTIMER.EXE (0x28DC)                    0x05F4 SharePoint Server Search       Administration               
     dl2n Verbose  Search application 'FAST Query SSA': Adding start address 'http://nvcp' for web application '57718ea1-8cb5-4adc-abd2-9e55415e5791' to list of valid start addresses. 85041609-d618-4132-ac8e-195a910d99a0
    07/30/2014 01:31:46.53  OWSTIMER.EXE (0x28DC)                    0x05F4 SharePoint Server Search       Administration               
     dmb6 Verbose  Ensure full read access to the indexing account 'ABc\sp_search' on web application 'http://nvcp'ext/'. 85041609-d618-4132-ac8e-195a910d99a0
    07/30/2014 01:31:46.53  OWSTIMER.EXE (0x28DC)                    0x05F4 SharePoint Server Search       Administration               
     dl2m Verbose  Search application 'FAST Query SSA': Skipping web application '64d562a1-535e-4917-8979-88840e2a67fe' because its outbound url 'http://nvcp'ext' was automatically added once. 85041609-d618-4132-ac8e-195a910d99a0
    07/30/2014 01:31:46.53  OWSTIMER.EXE (0x28DC)                    0x05F4 SharePoint Server Search       Administration               
     dl2n Verbose  Search application 'FAST Query SSA': Adding start address 'http://nvcpext' for web application '64d562a1-535e-4917-8979-88840e2a67fe' to list of valid start addresses. 85041609-d618-4132-ac8e-195a910d99a0
    07/30/2014 01:31:46.53  OWSTIMER.EXE (0x28DC)                    0x05F4 SharePoint Server Search       Administration               
     dmb6 Verbose  Ensure full read access to the indexing account 'ABC\sp_search' on web application 'http://nvcpnew/'. 85041609-d618-4132-ac8e-195a910d99a0
    executing SQL query {? = call dbo.proc_MSS_PropagationIndexerGetReadyQueryComponents}  [propdatabase.cxx:70]  d:\office\source\search\native\ytrip\tripoli\propagation\propdatabase.cxx 
    07/30/2014 01:32:04.31  mssearch.exe (0x0588)                    0x1DE4 SharePoint Server Search       Propagation Manager          
     e3o3 Verbose  executing SQL query {? = call dbo.proc_MSS_PropagationIndexerGetReadyQueryComponents}  [propdatabase.cxx:70]  d:\office\source\search\native\ytrip\tripoli\propagation\propdatabase.cxx 
    07/30/2014 01:32:04.68  mssdmn.exe (0x15CC)                      0x1060 SharePoint Server Search       HTTP Protocol
    Handler          du4i                     0x29E4 SharePoint Server Search       HTTP
    Protocol Handler          du4i Verbose  CHttpAccessorHelper::InitRequestInternal - opening request for '/robots.txt'.   [httpacchelper.cxx:353]  d:\office\source\search\native\gather\protocols\http\httpacchelper.cxx 
    07/30/2014 01:32:04.70  mssdmn.exe (0x15CC)                      0x29E4 SharePoint Server Search       HTTP Protocol
    Handler          du54 High     CHttpAccessorHelper::InitRequestInternal - unexpected status (503) on request for 'http://ppecpnew/robots.txt' Authentication 0.  [httpacchelper.cxx:703] 
    d:\office\source\search\native\gather\protocols\http\httpacchelper.cxx 
    07/30/2014 01:32:04.70  mssearch.exe (0x0588)                    0x130C SharePoint Server Search       Gatherer                     
     cd11 Warning  The start address http://nvcp'/sites/quipme cannot be crawled.  Context: Application 'FAST_Content_SSA', Catalog 'Portal_Content'  Details: 
    The crawler could not communicate with the server. Check that the server is available and that the firewall access is configured correctly. If the repository was temporarily unavailable, an incremental crawl will fix this error.   (0x80041200) 
    07/30/2014 01:32:04.70  mssdmn.exe (0x15CC)                      0x104C SharePoint Server Search       HTTP Protocol
    Handler          du4i Verbose  CHttpAccessorHelper::InitRequestInternal - opening request for '/robots.txt'.   [httpacchelper.cxx:353]  d:\office\source\search\native\gather\protocols\http\httpacchelper.cxx 
    07/30/2014 01:32:04.70  mssdmn.exe (0x15CC)                      0x104C SharePoint Server Search       HTTP Protocol
    Handler          du54 High  
    07/30/2014 01:32:04.70  mssearch.exe (0x0588)                    0x2948 SharePoint Server Search       Gatherer                     
     cd11 Warning  The start address
    http://nvcp'/sites/MDPPubng cannot be crawled.  Context: Application 'FAST_Content_SSA', Catalog 'Portal_Content'  Details:  The crawler could not communicate with the server. Check that the server is
    available and that the firewall access is configured correctly. If the repository was temporarily unavailable, an incremental crawl will fix this error.   (0x80041200) 
     CHttpProbeHelper::ProbeServer: InitRequest failed for 'http://ppecpnew/_vti_bin/sitedata.asmx'. Return error to caller, hr=80041200  [stscommon.cxx:490]  d:\office\source\search\native\gather\protocols\common\stscommon.cxx 
    07/30/2014 01:32:26.06  mssdmn.exe (0x15CC)                      0x193C SharePoint Server Search       PHSts                        
     dvg0 High     STS3::COWSServer::InitializeClaimsCookie: Probing url 'http://pncvr' failed. Return error to caller, hr=80041200  [sts3util.cxx:1332]  d:\office\source\search\native\gather\protocols\sts3\sts3util.cxx 
    07/30/2014 01:32:26.06  mssdmn.exe (0x15CC)                      0x193C SharePoint Server Search       PHSts                        
     en0e High     CSTS3Accessor::InitURLType: Return error to caller, hr=80041200                 [sts3acc.cxx:2214]  d:\office\source\search\native\gather\protocols\sts3\sts3acc.cxx 
    07/30/2014 01:32:26.06  mssdmn.exe (0x15CC)                      0x193C SharePoint Server Search       PHSts                        
     dv3p High     CSTS3Accessor::GetServer fails, Url sts4://pnvpr/siteurl=sites/product/siteid={7ebfb072-08a8-4df7-8f74-e06730325d9a}/weburl=/webid={bd7ae724-1256-4b26-9633-416447d6bc5c}, hr=80041200  [sts3acc.cxx:185] 
    d:\office\source\search\native\gather\protocols\sts3\sts3acc.cxx 
    07/30/2014 01:32:26.06  mssdmn.exe (0x15CC)                      0x193C SharePoint Server Search       PHSts                        
     dvb1 High     CSTS3Accessor::Init fails, Url sts4:/mngbv/siteurl=sites/product/siteid={7ebfb072-08a8-4df7-8f74-e06730325d9a}/weburl=/webid={bd7ae724-1256-4b26-9633-416447d6bc5c}, hr=80041200  [sts3handler.cxx:312] 
    d:\office\source\search\native\gather\protocols\sts3\sts3handler.cxx 
    07/30/2014 01:32:26.06  mssdmn.exe (0x15CC)                      0x16FC SharePoint Server Search       HTTP Protocol
    Handler          du2z Verbose  CHttpProbeHelper::ProbeServer: Probing server with url 'http://pnvpr/_vti_bin/sitedata.asmx'.  [stscommon.cxx:476]  d:\office\source\search\native\gather\protocols\common\stscommon.cxx 
    07/30/2014 01:32:26.08  mssdmn.exe (0x15CC)                      0x193C SharePoint Server Search       PHSts                        
     dvb2 High     CSTS3Handler::CreateAccessorExD: Return error to caller, hr=80041200            [sts3handler.cxx:330]  d:\office\source\search\native\gather\protocols\sts3\sts3handler.cxx 
    07/30/2014 01:32:26.08  mssdmn.exe (0x15CC)                      0x16FC SharePoint Server Search       HTTP Protocol
    Handler          du4i Verbose  CHttpAccessorHelper::InitRequestInternal - opening request for '/_vti_bin/sitedata.asmx'.  [httpacchelper.cxx:353]  d:\office\source\search\native\gather\protocols\http\httpacchelper.cxx 
    earch application 'FAST Query SSA': Adding start address 'http://mnvfgext' for web application '64d562a1-535e-4917-8979-88840e2a67fe' to list of valid start addresses. a6b7948a-dc16-419d-b58a-0ee798a0bb9c
    07/30/2014 01:32:46.53  OWSTIMER.EXE (0x28DC)                    0x1444 SharePoint Server Search       Administration               
     dmb6 Verbose  Ensure full read access to the indexing account 'ABC\sp_search' on web application 'http://nvpr/'. a6b7948a-dc16-419d-b58a-0ee798a0bb9c
    07/30/2014 01:32:46.53  OWSTIMER.EXE (0x28DC)                    0x1444 SharePoint Server Search       Administration               
     dl2m Verbose  Search application 'FAST Query SSA': Skipping web application 'cea7b67b-fd5f-4c9a-a300-64a7d7ca3093' because its outbound url 'http://pnvpr' was automatically added once. a6b7948a-dc16-419d-b58a-0ee798a0bb9c
    07/30/2014 01:32:46.53  OWSTIMER.EXE (0x28DC)                    0x1444 SharePoint Server Search       Administration               
     dl2n Verbose  Search application 'FAST Query SSA': Adding start address 'http://pnvpr' for web application 'cea7b67b-fd5f-4c9a-a300-64a7d7ca3093' to list of valid start addresses. a6b7948a-dc16-419d-b58a-0ee798a0bb9c
    07/30/2014 01:32:46.53  OWSTIMER.EXE (0x28DC)                    0x1444 SharePoint Server Search       Administration               
     dl2k Verbose  web application 'http://abcrsp/' doesn't use search application 'FAST Query SSA', skipping it. a6b7948a-dc16-419d-b58a-0ee798a0bb9c
    07/30/2014 01:32:46.53  OWSTIMER.EXE (0x28DC)                    0x1444 SharePoint Server Search       Administration               
     dl2k Verbose  web application 'http://excb/' doesn't use search application 'FAST Query SSA', ski
    Anil Loka

    Hi,
    According to your post, my understanding is that you got error when communicating to the server.
    This happens when crawler is not able to connect to the server. Make sure server name is correct. Couple of steps to troubleshoot it
    You should be able to ping the server from the server having crawl component. Make sure there is an entry for the server in the host file under c:\Windows\System32\drivers\etc folder.
              Ping <servername>
          2.  You should be able to connect to the server using telnet command
    Telnet< servername> <port number>
    More information:
    Troubleshooting of FAST Search Configuration
    If the issue still exists, you can delete the old search application and recreate from the beginning.
    You can also reset the index and do a full crawl after.
    Here is a similar thread for your reference:
    http://social.technet.microsoft.com/Forums/en-US/f3c61b53-304a-4c2a-a370-d0e573219d1d/an-unrecognized-http-response-was-received-when-attempting-to-crawl-this-item?forum=sharepointadminprevious
    Best Regards,
    Linda Li
    Linda Li
    TechNet Community Support

  • My facebook setting keeps saying "Error Signing In" "could not communicate with the server." How do I fix this?

    I have been trying to fix my facebook setting but I keep getting an error message after inputting my password. "could not communicate with the server" keeps popping up. [DELETE ACCOUNT] doesn't work either. It doesn't delete my facebook account at all. What else can I do?

    THIS HAS WORKED
    Apple Support Communities
    Re: IOS 7 Apple Settings Facebook Error
    created by Pegboarder in Using iPad - View the full discussion
    Go into settings/privacy/Facebook and disable the button.
    Open your Facebook app and login.
    Once logged in go back to that button and enable.
    You may have to re-enter your password but the error will be gone.
    Good luck.
    Did this help? Go to the message, sign in, and reply
    Start a new discussion in the same community
    You are receiving this email from Apple Support Communities. You can change your email preferences in your Apple Support Communities Profile.
    © 2013 Apple Inc. 1 Infinite Loop, MS 303-3DM, Cupertino, CA 95014.
    All Rights Reserved | Privacy Policy | Apple Support Communities Terms of Use | Apple Support

  • Database Mail not working with SQL Server Agent

    I'm running SQL Server 2005 Standard edition 64 bit with SP2 on a 64 bit machine. 
    Database mail does not work with SQL Server Agent.  When I configure SQL Server Agent to use database mail the test email button is greyed out and inactive therefore I cannot send emails using operators or for jub success failure etc. 
    I've read that there was supposed to be a fix for this with SP1 but I have SP2 and still receive the same problem.  Please can somebody help as I do not wish to use SQL Mail as a work around due to this becomming redundant in future versions of SQL Server.
    Kind Regards

    The problems solved
    steps:
    1)we create a mail profile at at Managment->Database Mail ,of SQL Managment
    2)we set this account as "default" at Managment->Database Mail -> Configure Database Mail -> Manage profile security
    3)At tab "Alert System" of SQL Server Agent properties , we check the "Enable mail profile" , Mail System=Database Mail, Mail profile = "the profile we already create"
    4)we create a new operator at "Operators" of sql agent, where at "notification options" -> "Email name" we put the mail where we want to sent the agent the mails at failured job
    5)We go at a specific job, at tab "Notifications" ,we check the "email" check box and then we choose the operator we just create, at the text box next to check box.
    I hope not to forget something
    Thank You all for the help

  • Standby Database not syncronized with primary.

    DB: 10.2.0.4.0
    OS RedHat Linux
    My standby Database not syncronized with primary, because of space issue mrp process was stopped.
    During that we added 4 datafile in primary database in that case how we can sync standby database?
    There are no unamed files on standby database.
    SQL> select name from v$datafile where name like '%UNNAME%';
    no rows selected

    Prath wrote:
    When i trying to recover database getting below error:
    Starting recover at 11-DEC-10
    RMAN-00571: ===========================================================
    RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
    RMAN-00571: ===========================================================
    RMAN-03002: failure of recover command at 12/11/2010 12:00:23
    RMAN-06094: datafile 73 must be restored
    Note: Datafile 73 not available on standby database.Execute select name from v$datafile statement from standby and post there.
    (Of course you can rebuild standby database again ,create standby controlfile and copy all datafiles)

  • Standby PRI not working with voice Gateway Router & CUCM

    Hi ALL ,            
    GOOD Day all of you .
    I am facing a big problem i.e  standby PRI not working with VG & CUCM , I have checked all the configuration parameter on VG & CUCM found ok but I am unable to make any call from standby link also incoming not come on the standby link . When I make a call on my Pilot no but getting busy tone .
    I observer the some errors on VG like Cause i = 0x8286 - Channel unacceptable on my second PRI channel .
    Please help me to reslove this proem .
    Following are the PRI configuration Parameter on CUCM .
    Product Specific Configuration Layout
    Line Coding  : HDB3
    Framing  : NON CRC4
    Clock  : External
    Input Gain (-6..14 db)  0
    Output Attenuation (-6..14 db)  0
    Echo Cancellation Enable 
    Echo Cancellation Coverage (ms)  64
    PRI configuration on VG
    interface Serial0/0/1:15
    encapsulation hdlc
    isdn switch-type primary-net5
    isdn incoming-voice voice
    isdn bind-l3 ccm-manager
    BR,
    SANDIPAN

    Hi Craig ,
    Thanks for your reply .
    We are using the full 30 channel E1 PRI .
    following are PRI Channel Statistics: 
    %Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 1. Layer 3 output may not apply
    ISDN Se0/0/0:15, Channel [1-31]
      Configured Isdn Interface (dsl) 1
       Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
        Channel :  1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
        State   :  0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
       Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
        Channel :  1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
        State   :  0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
    Please find following debug error
    VG_RO_01#isdn test call interface serial 0/0/0:15 09665484798
    Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User RX <- RRp sapi=0 tei=0 nr=5
    Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User TX -> RRp sapi=0 tei=0 nr=4
    Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User TX -> RRf sapi=0 tei=0 nr=4
    Mar 7 03:00:54.574: ISDN Se0/0/0:15 Q921: User RX <- RRf sapi=0 tei=0 nr=5
    CCIL_PUNE_DR_VG_RO_01#
    Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 09665484798
    Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=5 nr=4
    Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q931: SETUP pd = 8 callref = 0x0084
    Bearer Capability i = 0x8890
    Standard = CCITT
    Transfer Capability = Unrestricted Digital
    Transfer Mode = Circuit
    Transfer Rate = 64 kbit/s
    Channel ID i = 0xA9839F
    Exclusive, Channel 31
    Called Party Number i = 0x81, '09665484798'
    Plan:ISDN, Type:Unknown
    Mar 7 03:00:56.006: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=6
    Mar 7 03:00:56.018: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=4 nr=6
    Mar 7 03:00:56.018: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x8084
    Cause i = 0x8286 - Channel unacceptable
    Mar 7 03:00:56.022: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=5
    Mar 7 03:00:59.995: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=6 nr=5
    Mar 7 03:00:59.995: ISDN Se0/0/0:15 Q931: SETUP pd = 8 callref = 0x0084
    Bearer Capability i = 0x8890
    Standard = CCITT
    Transfer Capability = Unrestricted Digital
    Transfer Mode = Circuit
    Transfer Rate = 64 kbit/s
    Channel ID i = 0xA9839F
    Exclusive, Channel 31
    Called Party Number i = 0x81, '09665484798'
    Plan:ISDN, Type:Unknown
    Mar 7 03:01:00.007: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=7
    Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=5 nr=7
    Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x8084
    Cause i = 0x8286 - Channel unacceptable
    Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=6
    Mar 7 03:01:03.995: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=7 nr=6
    Mar 7 03:01:03.995: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x0084
    Cause i = 0x80E6 - Recovery on timer expiry
    Mar 7 03:01:03.995: ISDN Se0/0/0:15 **ERROR**: CCPCC_CallOrigination: SETUP timed-out (2nd T303) to NETWORK. The SETUP failed.
    BR ,
    SANDIPAN

  • The crawler could not communicate with the server on SharePoint 2010

    Dear Friends,
      we have two tier farm application and web is running in one server , and other one is database server, search crawling is not working  ,My search service application log giving these below errors ,  Can you please suggest me how to fix these
    errors and how to make the search crawling with out errors.This is very urgent friends, because I have these issues on production server. kindly help me to fix these issues as soon as possible.
    The crawler could not communicate with the server. Check that the server is available and that the firewall access is configured correctly. If the repository was temporarily unavailable, an incremental crawl will fix this error.
    An unrecognized HTTP response was received when attempting to crawl this item. Verify whether the item can be accessed using your browser.
    Please see the recent crawl history below, it is listed 124,062 24 errors.
    Crawl started
    Crawl completed
    Crawl duration
    Type
    Successes
    Warnings
    Errors
    Top Level Errors
    Deletes
    Not Modified
    Security Updates
    10/19/2014 11:55 PM
    10/20/2014 12:10 AM
    00:15:27
    Incremental
    0
    0
    124,062
    24
    0
    1
    0
    10/19/2014 10:55 PM
    10/19/2014 11:11 PM
    00:16:26
    Full
    1
    0
    124,062
    24
    valmiki

    thanks gain noddy, I found the actual problem now . It is crawling the site collection . but is not crawling the sub site. How to include sub site  to crawl  , I found this solution in Google , one suggested to do this but did not work out. 
    Can you please let me know how to include sub site to crawl its contents .
    The solution to this is frustratingly simple...
    At the root of the site, go to Site Actions >> Site Settings and choose Search and Offline Availability under Site Administration.
    Set the page indexing behavior to “Always index all Web Parts on this site”.
    Save and run a full crawl.
    valmiki

Maybe you are looking for