Server Admin doesn't work

Server Admin never connects to the server. If I put in the localhost, 127.0.0.1, the IP address (either), or the FQDN as the server name it just spins. It never connects.
In the log I see:
Sep 17 14:59:02 obcer42 servermgrd: [931] ServerManager _SMSocketRead(fd=10) timed out (count=-1,remaining=5)\n
Sep 17 14:59:02 obcer42 servermgrd: [931] ServerManager SSLRead/SMSocketRead(IPADDRESS1:fd=10) failed with -36 (errno=35)\n
Sep 17 14:59:02 obcer42 servermgrd: [931] ServerManager _SMSocketRead(fd=30) timed out (count=-1,remaining=5)\n
Sep 17 14:59:02 obcer42 servermgrd: [931] ServerManager SSLRead/SMSocketRead(IPADDRESS2:fd=30) failed with -36 (errno=35)\n
Where IP_ADDRESS1 and IP_ADDRESS2 = two different IP addresses on the box.
Any ideas?

127.0.0.1 is the address that loops you back to the same Mac. It should work, but ONLY when you are sitting at a keyboard directly connected to the Server computer.

Similar Messages

Cherokee-admin doesn't work

Hi Everyone!
I didn't use arch for a month, due to hd failure. So I bought new hard drive, installed arch and everything else as i always did. In result cherokee admin doesn't work.
'sudo cherokee-admin -x'
gives me following output with debug mode
DEBUG: SIGUSR1 invokes the console..
SIGUSR2 prints a backtrace..
Serwer 1.2.101 running.. PID=3458 Port=4000
DEBUG: SIGUSR1 invokes the console..
SIGUSR2 prints a backtrace..
Serwer 1.2.101 running.. PID=3464 Port=4000
DEBUG: SIGUSR1 invokes the console..
SIGUSR2 prints a backtrace..
Serwer 1.2.101 running.. PID=3470 Port=4000
After entering login and one-time password, I get 503 Service Unavailable.
Reinstalling arch haven't brought any changes.
I'd be grateful if You have any ideas how to solve my problem.
Thanks!

Struggling with the same problem for cherokee-admin-launcher, but solved:
[ERROR] - Did not find a suitable SUDO_ASKPASS application
by installing gksu and x11-ssh-askpass.
I'm now simply running 'sudo cherokee-admin -t' and pointing my webbrowser to http://127.0.0.1:9090/. That works.

TS1398 What would be the reason why when i try to connect my iphone to a wifi server; it doesn't work? It also doesn't pick up any wifi connections.

What would be the reason why when i try to connect my iphone to a wifi server; it doesn't work? It also doesn't pick up any wifi connections.

go to settings>general> reset network connections and then try again

Server Admin Doesn't show info for Software Update Service

In server admin, under the settings and available updates, I see a list of available updates, but they are labelled with the hash code for the update, not the name, and the info panel doesn't show any information like it should. We have our corporate firewall configured to allow connections to the server apple uses for this service so that we can get the updates. Any suggestions?

That option is only available after upgrading to iOS 5. It appears you have a 2nd generation unit, which can not be upgraded beyond iOS 4.2.1.

Server Admin & WGM not working after 10.6 upgrade

Hi,
I've just done a fresh install of SL Server and migrated my setup from a previous server (10.4.11). Now when i try launch Server Admin or WGM they just hang and have to be force quit. I've tried to reboot, repair permissions and delete the preferences files but still no joy. Has anybody got any ideas?
Thank you in advance
Dave

Network guys had changed DNS server address, updated details in system preferences and everything works now.

Search in Outlook 2010 with Exchange Server 2010 doesn't work properly

Hi all,
I have a problem with a clients Exchange 2010. Search function in Outlook 2010 doesn't work properly, the employee can't search mails and contact - he doesn't get any result :-(
In application syslog/protocol I get this error:
Function 'CISearch::EcGetRowsetAndAccessor' found, content indexing for database 'Mailbox Database 0139257080' caused by MSSearch-Error '0x80041820' deactivated
Can anybody help me with this, if its necessary I can give further information :-)
Thomas
Thomas Deinert

Hi,
What’s Exchange Version? Sometimes, after Installing Exchange 2010 SP 1, Searching via OWA or Outlook Online Mode may Fail. If so, please try the following solution:
Download the script
Repair-ExchangeSearchSymlinks.ps1 from the Script Center.
Copy the Repair-ExchangeSearchSymlinks.ps1 script to the Scripts directory on the Mailbox server (default installation is C:\Program Files\Microsoft\Exchange Server\v14\Scripts).
On the afflicted Mailbox server, open the Exchange Management Shell by right-clicking the shortcut and selecting “Run as Administrator”.
Within the Exchange Management Shell, navigate to the Exchange Scripts directory.
Within the Exchange Management Shell, run the following script: .\Repair-ExchangeSearchSymlinks.ps1
Within the Exchange Management Shell, run the following script (without the symbols [] and substitute the database name(s) for any databases you wish to reset: .\ResetSearchIndex.ps1 [-force] <dbname> [<dbname>]...
You will receive an Event ID 109 when the rebuilding of the index starts for each database and an Event ID 110 for each database when the index rebuild has completed.
After receiving Event ID 110 for each database, test to make sure search functions correctly with both OWA and Outlook operating in Online Mode.
Similar thread:
https://social.technet.microsoft.com/Forums/exchange/en-US/35db030c-277f-49d6-83d6-772f839a47f8/owa-2010-sp1-search-problems?forum=exchange2010
Best Regards.

Safari & OS X Server Wiki - Doesn't Work on iPad (64GB)

I was very disappointed to find that Safari on iPad wouldn't even display our OS X Server pages. I could log in and navigate the top page but it began to fail as I drilled down resulting in a grayed out screen with the spinnig gear.
I've heard that Apple's development groups work in silos and do not talk with each other or work to ensure interoperability between Apple systems. The OS X Server group seems to be especially isolated. The was true with iPhone and now seems to be with iPad.
If anyone finds a workaround please post it here.

Hummm... looks like it is some kind of question of speed because if I wait long enough it looks like the pages load after all. What I was considering "Doesn't work" is actually long load times... and I would say unexpectedly long load times. I'm doing a few more tests to verify this before I pull back the question or mark it answered.
Is anyone else experiencing very long load times for nested wiki pages?

All logins slow/failed, even local server admin won't work...

I've had an issue last Friday which reoccurred this morning concerning logins. Any logins on the network don't work, but take forever to come up with an error message. So I went to the server locally and tried the admin account there, but it hung as well (pinwheel for a few minutes, then spinning gear indefinitely). On Friday, a hard reboot seemed to fix the issue. Today, after hard rebooting, I could log in locally, but upon opening Server Admin, my server's info never came up (showed connected, but no info came up (in the software/hardware/etc area on the first page) and no services were listed. No network accounts could log in at this time (would take a minute and then the generic "Cannot log into this account due to an error").
Did another restart (via the apple menu this time) and everything is working fine for now. I couldn't find anything in any logs to indicate a problem (although it seems several logs restarted with the server restart).
Most clients are 10.6.2, a few are 10.5.8 and one is 10.4.11.

Happened again this morning. Hard restart seemed to fix it, but the RAID with the home folders on it took (3-drive RAID in the XServe, OS is on a separate solid state drive) about 5 minutes to mount.
Most logs seemed to have reset on the restart. There was no server system log at all or a DCHP system.log.
OD LDAP log's first line was "nse error = 2". Everything after that was after the restart.
OD Password Service Error log was full of "Unknown listener exception error." All entries were since the restart.
Couldn't find any other anomalies in any logs (although, like I said, most of them don't seem to exist anymore.
Now, I don't know if it's related, but the green light on the center RAID drive is off, but it seems to check out fine in System Profiler and Disk Utility. The blue access light works. I just figured it's a bad LED, but seems possibly related if the RAID's losing connection somehow (which could explain logins not working and its slow mounting behavior).
Any ideas would be greatly appreciated as this is really bringing us to a standstill.

Server admin doesn't display info

I'm experiencing slow network logons for our 10.6.8 Mac Mini server (circa 2009).
I can't get server admin to display any info - the fields are blank - both logged on locally and remotely.
I looked in some logs, but don't know which ones are useful as a starting point for this issue.
Can you help point me in the right direction?
Thanks

Do you get any errors or indications that changes are required when issuing the following (non-destructive, informational) Terminal.app command?
sudo changeip -checkhostname
Is the domain a real and registered domain, or is it a ".local" domain?
Is the configured server at a static IP address? (Either a static address on a private LAN, or a public static address.)
Is there exactly one DNS server or one pool of DNS servers, and is that DNS server or pool local? (Are there any references to other non-local-LAN DNS servers?)
Logs? Assuming the server isn't all that busy when you test, launch Console.app, start your connection test with the Server Tools, and look at the aggregate log display for errors. (If it's busier box and can't be quiesced for testing, then yes, you can have to drill down into individual logs, or grep -R the /var/log directory for server or such...) But without knowing what (else) is wrong, it's difficult to predict.

Server Admin doesn't show Print Queue status

When I look at my print queues (all 17) under Server Admin, it shows queue name, # of jobs, shared via (IPP & SMB), and printer kind (HP LJ 1022n and HP LJ P2015). It has a column for status, but this is always 100% empty/blank. Also, if I go to the Jobs tab, then I can pick "Jobs on Queue" for all the queues, but the line below for "Queue Status" is again always blank.
Is there something I can do to get this info to show up in Server Admin? I know that CUPS knows the printer status, as I can go to localhost:631 and see the status in the Printers list and the Jobs list.
It isn't life threatening. It is just annoying to have to go to the web page when Server Admin -almost- gets me everything I need to diagnose a teacher's printing problem remotely.

Hi Keith
You could always consult the Print Service logs. If you set the logging levels to Debug or Debug2 you should get everything. You have to be a bit careful with this as the log can get quite large. Other than that I don’t know of anything that is available out of the box.
There may be others that can suggest a 3rd party solution that gives you the appropriate feedback you are looking for. Opening port 631 should not be that much of risk I would have thought?
Tony

SBS 2003 server admin rights dont work access denied on VSS and Network settings

Hi I have just taken over support for a company and have inherited a SBS 2003 Server.
The server has had no backup for over a year (when the last admin left).
VSS does not work, so the back does not work, unable to install any other backup as no admin rights.
I want to repair it so I can do a backup to move to a new server.
I did not know the administrator account password (the last admin didn't tell anyone)
So I used a password reset boot cd and then restarted Windows 2003 in Directory Service Restore Mode.
Copied SRVANY and INSTSRV to a temporary folder, mine is called D:\temp. Copied cmd.exe to this folder too. Next ran at a command prompt instsrv PassRecovery "d:\temp\srvany.exe"
next
Started Regedit, and navigated to
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\PassRecovery
Created a new subkey called Parameters and added two new values:
name: Application
type: REG_SZ (string)
value: d:\temp\cmd.exe
name: AppParameters
type: REG_SZ (string)
value: /k net user administrator 123456 /domain
"123456 is substituted for the password I used" Im not daft enough to publish it lol
Next
opened the Services applet (Control Panel\Administrative Tools\Services) and opened the PassRecovery property tab. Checked the starting mode is set to Automatic.
to the Log On tab and enable the option Allow service to interact with the desktop.
Restart Windows normally, SRVANY run the NET USER command and reset the domain admin password.
OK so now I am logged in as administrator but guess what I still don't have admin rights???
I can add new user with admin rights and log in as them but they still don't have admin rights Im totally lost??????????? Help please

I'm thinking the previous tech may have renamed the built-in domain Administrator and then created a new account called 'administrator' with lesser rights? He then used another domain admin account to manage the server.
If so, and given the fact that you don't know any domain admin account usernames or passwords, I think you may be in for a move to a new server without a proper NT backup of the SBS 2003.
However, If you can at least log into the SBS 2003, I wonder if you could download and run DIsk2VHD and create VHDs (not VHDX) of the current SBS 2003 drives, saving them to an external USB drive connected to the server.
You could then 'attach' the VHDs to a Win7 Pro computer and gain access to the files/folders, although not the Active Directory stuff. Moving Exchange and Sharepoint would impose additional pain. For Exchange, you could log
onto workstations as each user and export their Exchange mailboxes as .PSTs. I believe you could do the same with any Public Folders.
Disk2VHD
http://technet.microsoft.com/en-us/sysinternals/ee656415.aspx
How to Mount a Virtual Hard Disk in Windows 7
http://www.online-tech-tips.com/windows-7/mount-vhd-windows-7/
Of course, the owner could also have his attorney contact the previous tech and threaten legal action unless he coughs up the correct domain admin username and password. That username and password belong to the owner, not the
tech.
Merv Porter
=========================

Export settings within Server Admin doesn't really

So I've had a whootin good time with a migration. Situation was a dual g4 died on me, right after I'd imaged it to a mac mini. I have another mac mini that I wanted to setup as a backup machine/tester. I tried one time to export all the server settings and admin settings and that didn't work at all, so I decided to export say...just my firewall settings, then import just the firewall settings back in. That worked, but didn't have all my firewall settings (ended up having to copy ipfw.conf.apple over). I then tried the same with just dns settings, but that didn't work..I'd import in, the zones would flash up on the zone list, then vanish. Has anyone ever successfully exported and imported settings? So far it's seemed like kind of a waste of time if it's not gonna copy everything over. I dunno...maybe it's the g4 imaged to the macmini that I'm exporting from. All of these are on 10.5.6 using the latest build of Server Admin

Have a look at the following:
http://support.apple.com/kb/TS3960

Test content server connection doesn't work

Hello,
I have installed Content Server 6.40 in windows2008 and the test connection does not work. The URL http://onecsrdev:1090/ContentServer/ContentServer.dll?serverInfo
says
Internet Explorer cannot display the webpage
Most likely causes:
You are not connected to the Internet.
The website is encountering problems.
There might be a typing error in the address.
I loof for the contentserver.dll file and it does not exist in the server. When I installed the content server I mark the flag install website, so I don't understand what the problem is.
I have updated the MAXDB software to 7.6.06.11 because the DVD installation release is not valid for windows2008. SAP has guided me through this issue.
Thanks and best regards,
Ana

> I have installed Content Server 6.40 in windows2008 and the test connection does not work. The URL http://onecsrdev:1090/ContentServer/ContentServer.dll?serverInfo
> says
> Internet Explorer cannot display the webpage
You get a connection to "onecsrdev"? Can internet explorer resolve the name? Proxies activated?
Markus

HotFix4 for SQL Server 2005 doesn't work

I am having problems getting a machine running SQL Server 2008 R2 (Express) to connect to a SQL Server 2005 (Full Standard Edition) DB on another machine via the LAN. It times out when connecting from a C# application. SSMS on the SQL 2008 machine
connects fine, but SSMS on the 2005 machine (connecting to a copy of the same DB on the 2008 machine) says it isn't supported and I need a hotfix.
I downloaded the hotfix link from Microsoft, but when I paste it into the Browser I get a DNS name failure for the Hotfix4 server. I don't want to paste the full link here because it is not made public by MS and you need to request it. However, the
first part of the URL is: http://hotfix4.microsoft.com/SQL%20Server%202005...etc.
I have checked out all of the obvious things in both instances (2005 AND 2008)... Both instances are configured to accept remote connections, both have TCP/IP and named pipes protocols enabled, both are running fine for local connections, both have the SQL
Browser enabled and the Computer Browser Service running on the network.
As the hot fix doesn't install, I am kind of out of ideas.
Any suggestions?
Thanks,
Pete
I used to write COBOL... now I can do anything.

SQL 2005 is out of
mainstream support:
SQL Server
2005
SP4
04/12/2011
04/12/2016
Technical support continues till 04/12/2016, yet mainstream (hotfix) support ends as of 04/12/2011; options
for hotfix support after 04/12/2011:
ð  Continue
with self-help
ð  Upgrade
to the latest supported service pack for SQL Server 2005 or SQL Server 2008 or SQL Server 2008 R2
ð  Extended
hotfix support agreement
SP4 and CU3 are still available for download, if this helps...
http://support.microsoft.com/kb/2507769
http://www.microsoft.com/en-US/download/details.aspx?id=7218
But you should update your SQL-Server..... SQL 2014 is the latest version

Adobe Connect Enterprise Server 6 doesn't work on Firefox and Chrome

Hi everyone, we are using adobe connect enterprise server 6 recently the layout on Chrome and Firefox looks horrible but it works fine on IE, i have attach a photo of how it look on Firefox, any suggestion what the problem might be, thanks in advance.
When we get this when we login:
function showContentWithNav(url, pres, session, cw, ch, noScale, scrollbar, toolbar, status, location, target) {
        if (target == undefined)
            target = "";
no need for adding session in URL. could be misused or mistakenly sent by user to others.
and then used to access to webapp by someone.
-- REMOVING IT   --
var w, h, l, t;
if (pres) {
w = 0.96 * screen.width;
h = 0.76 * screen.height;
l = (screen.width - w) / 2;
t = (screen.height - h) / 2;
} else if (noScale) {
w = cw;
h = ch;
l = (screen.width - w) / 2;
t = (screen.height - h) / 2;
} else {
if (cw > 0 && ch > 0) {
if (cw <= screen.width) {
w = cw;
h = w * ch /cw;
if (h > screen.height) {
h = screen.height;
w = h * cw / ch;
} else {
w = 0.4 * screen.width;
h = 0.3 * screen.height;
l = (screen.width - w) / 2;
t = (screen.height - h) / 2;
var options = "toolbar=" + toolbar + ",status=" + status + ",location=" + location + ",resizable=1,left=" + l + ",top=" + t + ",width=" + w + ",height=" + h;
if (scrollbar==false)
options += ",scrollbars=no";
else
options += ",scrollbars=yes";
var win = open(url, target, options);
     * Default showContent window, which displays popup w/ no navigation.
    function showContent(url, pres, session, cw, ch, noScale, scrollbar, target) {
      var toolbar = 0;
var status = 0;
var location = 0;
showContentWithNav(url, pres, session, cw, ch, noScale, scrollbar, toolbar, status, location, target);

I opened a new Flex project and then tried again. I finally found that it's not a problem of flash but div rendering.
It seems Firefox and Chorme don't pass mouse wheel event automatically if div layout is set to "absolute".
Although this is not a Flex issue, any idea of passing that event to flash will be appriciated. I haven't find a way to do it so far :-(
What I'm doing is editing the "index.tamplate.html" to test. I added a div to contain the div of "flashContent" and set it's style to:
    position: absolute;
    top: 150px; left: 150px;
    height: 250px; width: 250px;
    z-index: 10;
Another div's z-index is set to 1 to test the overlay effect.
The reason why I added a div to contain the original div of flash, is I cannot figure out a way to effectively edit the CSS of the "flashContent" div.
Any help will be thankful!!

Server Admin doesn't work

Similar Messages

Maybe you are looking for