Server could not find any Meta-Data devices!

Our MDC dropped out and the backups did not engage.
On a reboot of the MDC we were able to mount the volume, but all files (QuickTme movies, FCP projct files) could not be opened with an "unknown file type error".
We shut all the clients down we checked the volume and (cvfsck -nv) and while "dirty" it did not report any errors.
Stopped the volume and ran a cvfsck -w which gave us:
"Server could not find any Meta-Data devices!"
Checking Xsan admin logs shows us:
"PioOpen: no such device.
Fatal: Cannot open stripe group "md" - Operation not supported by device
Fatal: Physio_init failed."
Where "md" is our metadata storage pool.
We shutdown all switches, RAIDS, clients, etc, but bring them all back up and checking with one MDC or another is the same result. Volume will not mount.
All fiber connections seem good, checked in RAID admin and on switch.
Ideas?

AppleCare suggested that maybe a metadata backup could have helped.
http://docs.info.apple.com/article.html?artnum=303371
In any case, we nuked and paved.

Similar Messages

Data selection procedure 400 could not find any data

Hi ,
I am getting the Information message "Data selection procedure 400 could not find any data " while doing the Result recording of a inspection lot
Inspection lot status :- REL CALC
Inspection lot Origin :- 04 GR from production order
No user status active
This message i am getting in some inspection lot only
Kindly help me to understand the possible resaon for this message
Thanks,
Ishwar

hi,
u r using any copy inspection result like of thing, if not than please provide the Mssg number. and possible than check ur plan properly.
F9 i have checked, this prblm occurs when u using the Copy inspecttion result during RR in QA32, ma suggesstion is to checck ur config "Copy inspection results" in SPRO properly against inspection type "04", and than check ur qaulity plan, than execute it will resolve.
For more information:
SPRO Settings: COPY INSPECTION RESULTS DURING RESULTS RECORDING
Regards
Edited by: D GURU on Dec 5, 2011 8:35 AM

Could not find any data to display - how to modify system message

Hi,
We created an exception report in the Web Application Designer.
If there are no exceptions (so there is no data to display) the following standard system message is shown:
Could not find any data to display. This might be due to the current selection of variable or filter values
We would however like to modify/remove this message.
How can this be done?
Thanks
Dave

Hi,
Please check the link:
/people/marc.bernard/blog/2008/10/10/how-to-filter-messages-created-by-bi-ip-planning-functions-and-sequences
Please check the Q&A section of above weblog which mentions about
function module RRMS_MESSAGE_HANDLING which could be helpful.
Please also refer to SDN thread:
Re: WAD - messages - message type
Regards,
Amit

RFC call failed: JCO.Server could not find server function 'SET_SLD_DATA'

Hi, All
the system is PI 7.0 EHP1 oraclei Win2003 server, I configured SLD but I run RZ70, having error "RFC call failed: JCO.Server could not find server function 'SET_SLD_DATA' ". I know there are lot of tread about this error, but none of themsolve my problem. all JCO, RFC connections and SDL DATA supplier(VA) seem OK. error message in SM21 is "Could not send SLD data"
detail from SM21
The system could not send the data that has been collected automatical
for the System Landscape Directory (SLD). Check whether the gateway
configured in transaction RZ70 has been started and whether the SLD
bridge has been registered with this gateway.
You can use transaction SM59 to check this in the sending system for t
implemented RFC destinations. The RFC destinations have the standard
names "SLD_UC" for Unicode sending systems and "SLD_NUC" for non-Unico
sending systems. If a different RFC destination has been entered in
RZ70, check this destination instead.
You can use the Gateway Monitor to check the target gateways. In ABAP
systems, this monitor is started with transaction SMGW, or you can use
the external SAP program "gwmon". Check whether the specified gateway
has an active registration.
OF COURSE I checked RFC of SLD_UC and SMGW
any different ideas
Regards
ABH

Hi
Please check the following notes are implemented
Note 906454
Note 907729
You may be aware but if you are not --->RZ70 creates the required SLD* RFCs during runtime - therefore if you have defined these RFCs manually first using the same namespace you can get RFC conflicts which result in a failed submission
Please also check the user in the RFC is known to both systems and has required authorization to write to SLD
Generally with SLD you have to install or select a suitable gateway to handle incoming data supply traffic
Also the gateway you are using has be known to SLD and reflected in RZ70 - i.e these defintions have to be the same
It is also recommended to delete all references to SLD_* RFCs in data supplier and target SLD
after a failed submission attempt to allow RZ70 to recreate these consistently once the above has been checked
Best wishes
Stuart

[Microsoft][ODBC SQL Server Driver][SQL Server]Could not find stored procedure 'dbo.sp_SPNAMEHERE'.

OK, something seemed to have changed with my system because this error is NEW. It might be related to my system upgrade from Vista to Win7, but just guessing here.
I run a database on a corporate MS Sql Server (2005) and an ASP application that connects via ODBC. The real world application works fine, however when I attempt to access Stored Procedures from Dreamweaver (on my development machine) I am getting the following error:
[Microsoft][ODBC SQL Server Driver][SQL Server]Could not find stored procedure 'dbo.sp_SPNAMEHERE'.
This only seems to happen on Stored procedures that RETURN a recordset.
system:
Win7
Dreamweaver CS4
Code: VBScript/Classic ASP
SQL Server 2005
Connecting via ODBC: MM_MY_STRING = "Driver={SQL Server};Server=wscxxxxxxxxx;Database=dbsystem;Uid=username;Pwd=XXXXXXXXXXXX"
Stored procedures that do not return a recordset are not an issue.... this has put my development work at a standstill!!
Thanks in advance!

Well, I hate bumps, but I am really running out of solutions. I have now tried to use a system DSN on my development machine and that didnt solve the problem. I just un-installed DW and re-installed it and that didnt solve my problem either.
This is very frustrating, because I cannot use any stored procs that return recordsets... I am stuck... can anybody think of a relatively easy work-around to working in DW w/ recordsets that come from SPs when you cant actually access them?
The really weird thing is, when I build the command, and choose the stored proc, and give it valid input variables, and TEST it from the TEST button, everything works and data is returned as expected. Once I click "OK" and actually add it to the ASP page the recordset that should be visible isnt... and when I click the plus sign in the bindings window I get the error...
Help!!

Oracle error: The listener could not find any available service handlers...?

I'm running Coldfusion 8 and Oracle XE 10, both on IIS 7.
Every so often, I get this message:
[Macromedia][Oracle JDBC Driver][Oracle]ORA-12519 The
listener could not find any available service handlers that are
appropriate for the client connection. One possible cause for this
error is that the server was not configured for the specified
server type (shared/dedicated).
I can restart the OracleServiceXE service and it works fine.
However, I have no clue what is causing this. I believe it all
began once I started using CFSCRIPTS and running queries using that
instead of CFML. Would anyone know what COULD cause this error to
happen and what I should look out for? I am new to Oracle and CF
btw.
Also, I can access it fine through the oracle homepage, but
when I attempt to connect to it from the coldfusion administrator,
it cannot establish a connection to that data source. It is only
after I restart the service that things go back to normal. Thanks.
Ryan

Hello,
Can you provide output of the following? Any other errors along with this error in alert.log file? Also your listener.ora and tnsnames.ora?
lsnrctl>set displaymode verbose
lsnrctl>services your_listener_name
lsnrctl>status
$> sqlplus '/as sysdba'
sql> select * from v$resource_limit;Regards
Edited by: OrionNet on Jan 14, 2009 10:17 PM
Edited by: OrionNet on Jan 14, 2009 10:22 PM

JCO.Server could not find server function "ZVERIFY_FILE"

Hi Experts,
I am facing one problem, i have created on TCP/IP connection with connection type T and given it some Program Id.
I have register this Program id On SRM server.
Now from this server i want to call one JAVA file, for that purpose i have installed JCO on the server.
My server file looks like,
import com.sap.mw.jco.*;
//import com.tcs.jns.JSignNS;
//import com.tcs.jns.JSignNSException;
//import com.tcs.jns.CertDetails;
// added by paresh on 16.1.2009
import java.io.FileOutputStream;
import com.tcs.jie.jverify.JVerify;
import com.tcs.jie.jsign.JSign;
public class ds_listener extends JCO.Server {
Create an instance of my own server
@param gwhost (gateway host)
@param gwserv (gateway service number)
@param progid (program id)
@param repository (repository used by the server to lookup the definitions of an inc)
     public ds_listener(String gwhost, String gwserv, String progid, boolean isUnicode, IRepository repository) {
          super("sapdev14", "sapgw01", "DS_RFC", repository);                this.setProperty("jco.server.unicode", isUnicode?"1":"0");
     /** Overrides the default method. */
     static ds_listener serverConnections[] = new ds_listener[1];
     protected void handleRequest(JCO.Function function) {
          JCO.ParameterList input = function.getImportParameterList();
          JCO.ParameterList output = function.getExportParameterList();
          if (function.getName().equals("ZVERIFY_DATA")) {
               try{
                    JVerify JNS = new JVerify();
                    String dbPath = "/home/admin/FormSigner_23Apr/FormSigner_Release/certdbs";
                    //boolean res = JNS.init (dbPath); // commented by paresh on 16.1.2009 as its obsolute
                    //initialize method has to be called before calling any other method of the API
                    String recdSignature = input.getString("SIGNATURE");
                    boolean ret_update = JNS.updateSignature(recdSignature.getByetes());
                    if (ret_update){
                         int count = JNS.getSignerCount();
                         boolean ret_verify_sign = false;
                         while(count > 0){
                              ret_verify_sign = JNS.verifySignature(count - 1);
                              if (ret_verify_sign){
                                   ret_verify_sign = false;
                                   count = count - 1;
                              }else
                                   break;
                         if (count == 0){
                              String decoded_data = new String(JNS.getDecodedData());
                              output.setValue("X", "STATUS");
                              output.setValue(decoded_data, "DATA");
                         }else{
                              output.setValue(" ", "STATUS");
                              output.setValue("Error in Signature Verification. Please check Certificate Validity of every signer.", "DATA");
               }catch (Exception e1){
                    output.setValue(" ", "STATUS");
                    output.setValue(e1.getMessage(), "DATA");
          }else if(function.getName().equals("ZVERIFY_FILE")) {
               try{
                    JVerify JNS = new JVerify();
                    String dbPath = "/home/admin/FormSigner_23Apr/FormSigner_Release/certdbs";
                    //boolean res = JNS.init (dbPath); // commented by paresh on 16.1.2009 as its obsolute
                    //initialize method has to be called before calling any other method of the API
                    String recdSignature = input.getString("SIGNATURE");
                    boolean ret_update = JNS.updateSignature(recdSignature.getBytes());
                    if (ret_update){
                         int count = JNS.getSignerCount();
                         boolean ret_verify_sign = false;
                         while(count > 0){
                              ret_verify_sign = JNS.verifySignature(count - 1);
                              if (ret_verify_sign){
                                   ret_verify_sign = false;
                                   count = count - 1;
                              }else
                                   break;
                         if (count == 0){
                              output.setValue("X", "STATUS");
                         }else{
                              output.setValue(" ", "STATUS");
               }catch (Exception e1){
                    output.setValue(" ", "STATUS");
          }else{
               return ;
Start the server
     public static void startServers() {
          JCO.addClientPool("POOL",3,"200","sisldp","paresh1234","EN","sapdev14","01");
          IRepository repository = JCO.createRepository("REP", "POOL");
          for (int i = 0; i < serverConnections.length; i++) {
               // Server listens for incoming requests from system 1
               // (Change gateway host, service, and program ID according to your needs)
               serverConnections<i> = new ds_listener(
                         "sapdev14",//gateway host, often the same as host
                         "sapgw01", //gateway service, generally sapgw+<SYSNR>
                         "DS_RFC", // corresponds to program ID defined in SM59
                         true, // or false for non unicode listener
                         repository);
               serverConnections<i>.start();
     public static void main(String[] args) {
     startServers();
The file have no error as i have compiled it on server, its listener file given in JCO with some modification.
I have tested the connection from SM59 it's working fine,but when i call my any of the 2 function(ZVERIFY_DATA & ZVERIFY_FILE) defined in my java file then i am getting an error "JCO.Server could not find server function 'ZVERIFY_FILE'" on SRM screen.
Can anyone tell me what can be the reason????
please help, i am in real trouble.

Hi,
This is may be of the wrong FunctionModule name means check in case also,it may be case sensitive.
And check whether it is remotely enabled or not and check the RFC destination.
For more details refer these threads.
JCO.Server could not find server function 'SET_SLD_DATA'
JCO.Server could not find server function
Problems with sender RFC
Thanks.

Could not find any available Global Catalog in forest when running RemoteMailbox cmdlet

My current Exchange environment is a hybrid configuration of Office 365, Exchange 2013 hybrid, and Exchange 2007 on-premise.
I have a script responsible for enabling remote mailboxes and assigning O365 licenses to a list of users; essentially provisioning users an O365 mailbox. This script runs every hour through a defined scheduled task in the Task Scheduler.
The script is proven to work but will intermittently throw an error on some days: "Could not find any available Global Catalog in forest root.xyz.com"
Here are the nuances of the error when it does occur:
It will only throw the error when the script is run via scheduled task - the script will work fine if executed from the command line
The error occurs when "Enable-RemoteMailbox" or "Get-RemoteMailbox" is called.
The same error will occur with ANY script that calls "Enable-RemoteMailbox" or "Get-RemoteMailbox" and is ran via scheduled task - even when the RemoteMailbox cmdlet was the only line in the script
Here is the output and error when Get-RemoteMailbox -verbose is ran:
VERBOSE: [15:49:52.474 GMT] Get-RemoteMailbox : Active Directory session
settings for 'Get-RemoteMailbox' are: View Entire Forest: 'True',
VERBOSE: [15:49:52.489 GMT]
Get-RemoteMailbox : Runspace context: Executing
user: ,
Executing user organization: ,
Current organization: ,
RBAC-enabled:Disabled.
VERBOSE: [15:49:52.489 GMT] Get-RemoteMailbox : Beginning processing
VERBOSE: [15:49:52.521 GMT] Get-RemoteMailbox : Current ScopeSet is: {
Recipient Read Scope: {{, }},
Recipient Write Scopes: {{, }}, Configuration Read Scope: {{, }},
Configuration Write Scope(s): {{, }, },
Exclusive Recipient Scope(s): {},
Exclusive Configuration Scope(s): {} }
VERBOSE: [15:49:52.521 GMT] Get-RemoteMailbox : Resolved current organization: .
VERBOSE: [15:49:52.521 GMT] Get-RemoteMailbox : Searching objects "abose" of type "ADUser" under the root "$null".
VERBOSE: [15:49:52.536 GMT] Get-RemoteMailbox : Previous operation run on global catalog server 'evw-xyzdc-p02.ad.xyz.com'.
Get-RemoteMailbox : Could not find any available Global Catalog in forest root.xyz.com.
At C:\IDM_In\Scripts\MinimalTest.ps1:42 char:14
+ $abose = Get-RemoteMailbox 'abose' -verbose
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : NotSpecified: (:) [Get-RemoteMailbox], ADTransientException
+ FullyQualifiedErrorId : E421EF0B,Microsoft.Exchange.Management.RecipientTasks.GetRemoteMailbox
VERBOSE: [15:49:52.567 GMT] Get-RemoteMailbox : Ending processing
What could be the cause of this intermittent error?
Thanks for any help

looks to me permission error as when you are running it via a schedule task is is not able to call exchange shell/ commands {confirm this} where as when you running this manually looks to me you open exchange shell, may be as admin also and then running
the script.
schedule task process is not able to get the permission..
MARK AS USEFUL/ANSWER IF IT DID
Thanks
Happiness Always
Jatin

The system could not find any entries that are relevant to costing.

plz give the solution ,its urgent
Message no. CK060
Diagnosis
The system could not find any entries that are relevant to costing.
System Response
The system did not cost the object.
Procedure
Check whether the following objects should be flagged as relevant to costing:
Items in the BOM
Display BOM
Operations in the routing
Control key in the routing
1. Look at the message log.
2. Check whether a quantity was specified in the confirmation.

hi,
iam facing the problem while creating the
stnadard cost estimate ck11n
the system prompts the following message
confirmation
Logistics - General (LO)
Information from the vendor to the recipient about the status of the purchase order.
The term confirmation covers different types of information from the vendor to the customer, such as order, loading or transportation confirmation and the shipping notification.
If materials planning takes place without a confirmation, planning can only be based on the delivery dates and quantities in the purchase order. In contrast, confirmations make it possible for the customer to plan the materials more precisely because between the purchase order and planned delivery date, more reliable information has become available.
Logistics - General (LO)
Communication sent by a vendor to a customer regarding the status of a purchase order.
The term "confirmation" (short for "vendor confirmation") is an umbrella term for various types of information provided by a vendor to a customer, including order acknowledgments, loading or transport confirmations and shipping notifications.
If the customer's materials planning and inventory control system does not work with confirmations, it can only refer to the delivery dates and quantities set out in the purchase order. The use of confirmations, on the other hand, makes the materials planning and inventory control process more precise, since between the PO date and the planned delivery date the customer receives increasingly reliable information about the pending arrival of ordered goods.
Treasury Management (TR-TM)
After concluding a financial transaction, a confirmation of the related contract data is sent to the relevant business partner. Confirmations can be printed or sent electronically directly from the R/3 System. Confirmation forms are defined via the correspondence type.
Logistics - General (LO)
Part of order monitoring, this documents the processing status of operations or sub-operations. In the SAP System, a distinction is made between partial and final confirmations.
A final confirmation is used to determine
at which work center the operation should be carried out
who has carried out the operation
the quantities of yield and scrap quantities that have been produced
the size of the standard values required for the actual operation
Materials Management (MM)
Communication from a vendor to a customer providing information on the status of a purchase order.
As used in this sense, the term "confirmation" can cover a number of different documents, such as order acknowledgment, loading confirmation, or shipping notification. Also termed "order acceptance/fulfillment confirmation".
If the materials planning and control system operates without such confirmations, it can only work on the basis of the delivery dates and quantities in the purchase order. Confirmations, on the other hand, enable the customer to plan more exactly. In the period between the issue of the PO and the planned delivery date he is provided with more up-to-date and increasingly reliable information on the expected delivery.
Project System (PS)
A confirmation is a part of network control. It documents the state of processing for network activities and activity elements. There are two types of confirmations in the R/3 System: partial and final confirmations.
A confirmation is used to record:
the work center where the activity was carried out
the person who carried out the activity
the yield and scrap produced in an activity
the actual values for the standard times
Intellectual Property Management (CRM-IM-IPM)
A report made by the licensee and defined in the rights sale contract on sales volumes or other quantities (such as audience figures for a film) during a period.
Receiving (ECO-BBP-REC)
An electronic document that combines the functions of goods receipts and service entry sheets. By creating a confirmation:
Vendors can confirm that they have fulfilled their orders
Employees can confirm the goods and services they ordered via their shopping baskets
Central goods recipients can confirm the goods and services ordered by employees for whom they are responsibleconfirmation
Logistics - General (LO)
Information from the vendor to the recipient about the status of the purchase order.
The term confirmation covers different types of information from the vendor to the customer, such as order, loading or transportation confirmation and the shipping notification.
If materials planning takes place without a confirmation, planning can only be based on the delivery dates and quantities in the purchase order. In contrast, confirmations make it possible for the customer to plan the materials more precisely because between the purchase order and planned delivery date, more reliable information has become available.
Logistics - General (LO)
Communication sent by a vendor to a customer regarding the status of a purchase order.
The term "confirmation" (short for "vendor confirmation") is an umbrella term for various types of information provided by a vendor to a customer, including order acknowledgments, loading or transport confirmations and shipping notifications.
If the customer's materials planning and inventory control system does not work with confirmations, it can only refer to the delivery dates and quantities set out in the purchase order. The use of confirmations, on the other hand, makes the materials planning and inventory control process more precise, since between the PO date and the planned delivery date the customer receives increasingly reliable information about the pending arrival of ordered goods.
Treasury Management (TR-TM)
After concluding a financial transaction, a confirmation of the related contract data is sent to the relevant business partner. Confirmations can be printed or sent electronically directly from the R/3 System. Confirmation forms are defined via the correspondence type.
Logistics - General (LO)
Part of order monitoring, this documents the processing status of operations or sub-operations. In the SAP System, a distinction is made between partial and final confirmations.
A final confirmation is used to determine
at which work center the operation should be carried out
who has carried out the operation
the quantities of yield and scrap quantities that have been produced
the size of the standard values required for the actual operation
Materials Management (MM)
Communication from a vendor to a customer providing information on the status of a purchase order.
As used in this sense, the term "confirmation" can cover a number of different documents, such as order acknowledgment, loading confirmation, or shipping notification. Also termed "order acceptance/fulfillment confirmation".
If the materials planning and control system operates without such confirmations, it can only work on the basis of the delivery dates and quantities in the purchase order. Confirmations, on the other hand, enable the customer to plan more exactly. In the period between the issue of the PO and the planned delivery date he is provided with more up-to-date and increasingly reliable information on the expected delivery.
Project System (PS)
A confirmation is a part of network control. It documents the state of processing for network activities and activity elements. There are two types of confirmations in the R/3 System: partial and final confirmations.
A confirmation is used to record:
the work center where the activity was carried out
the person who carried out the activity
the yield and scrap produced in an activity
the actual values for the standard times
Intellectual Property Management (CRM-IM-IPM)
A report made by the licensee and defined in the rights sale contract on sales volumes or other quantities (such as audience figures for a film) during a period.
Receiving (ECO-BBP-REC)
An electronic document that combines the functions of goods receipts and service entry sheets. By creating a confirmation:
Vendors can confirm that they have fulfilled their orders
Employees can confirm the goods and services they ordered via their shopping baskets
Central goods recipients can confirm the goods and services ordered by employees for whom they are responsible

JCO.SERVER could not find the server function

Hi,
I am calling "BAPI_COMPANY_GETDETAIL".thuough the zprogram"ZBAPI_COMPANY_GETDETAIL"
REPORT ZBAPI_COMPANY_GETDETAIL.
DATA:BEGIN OF ITAB,
RCOMP LIKE T880-RCOMP,
END OF ITAB.
ITAB-RCOMP = 99999.
CALL FUNCTION 'BAPI_COMPANY_GETDETAIL'
EXPORTING
COMPANYID = ITAB.
IMPORTING
COMPANY_DETAIL =
RETURN =
The Details I Gave......
In SM59 of R/3:
PROGRAMID:LCRSAPRFC_PIT
GATEWAYHOST:PITEST
GATEWAYSERVICE:sapgw01
Tested the connection and it is running
ID:
In Communication Channel.
Application server (Gateway):PITEST
Application server Service (Gateway):
PROGRAMID:LCRSAPRFC_PIT
RFC Metadata Repository parameter.
ip of XI Server
System No Xi System NO
username
pwd
In SM58 I find the Following error.
"JCO.SERVER could not find the server function BAPI_COMPANY_GETDETAIL.
I Tested RFC ADAPTOR in RWG and it is ok.
I do not Understand where the problem is.
Please clarify.
Thanks,
Srinivasa

Thanks for the reply,
Yes RFC is in the Sender side.
I am calling "BAPI_COMPANY_GETDETAIL".thuough the zprogram"ZBAPI_COMPANY_GETDETAIL"
REPORT ZBAPI_COMPANY_GETDETAIL.
DATA:BEGIN OF ITAB,
RCOMP LIKE T880-RCOMP,
END OF ITAB.
ITAB-RCOMP = 99999.
CALL FUNCTION 'BAPI_COMPANY_GETDETAIL'
EXPORTING
COMPANYID = ITAB.
IMPORTING
COMPANY_DETAIL =
RETURN =
The Details I Gave......
In SM59 of R/3:
PROGRAMID:LCRSAPRFC_PIT
GATEWAYHOST:PITEST(XI system name)
GATEWAYSERVICE:sapgw01
Tested the connection and it is running
ID:
In Communication Channel.
Application server (Gateway):PITEST(XI system name)
Application server Service (Gateway):
PROGRAMID:LCRSAPRFC_PIT
RFC Metadata Repository parameter.
ip of XI Server
System No Xi System NO
username
pwd
In SM58 I find the Following error.
"JCO.SERVER could not find the server function BAPI_COMPANY_GETDETAIL.
I Tested RFC ADAPTOR in RWG and it is ok.
I do not Understand where the problem is.
These is what I gave,

JCO.Server could not find server function 'CONTROL_RECIPE_AVAILABLE'

Hi Experts,
I've been trying to read some of the topics in the forums to find answers about the error JCO.Server could not find server function but still haven't resolve the issue.
Basically, the scenario is from SAP r/3 to PI 7.1 ehp1 (process integration) system.
All of the aforementioned steps we're done.
R/3 (SAP) end
1.) Create RFC destination (T)
2. ) Indicate the program ID
3.) Indicate the server/hostname
4.) Indicate the sap gateway
Test connection was made and it was successful.
SAP PI end.
Integration Directory (Let me skip from the basics and state directly the setup of my senderRFC)
1.) RFC Comm Channel (set as Sender)
2.) Indicated the server hostname (sending system), sap gateway and Program ID (basically what was indicated in RFC setup in SAP end)
3.) RFC Metadata Repository Parameters (In here I used the details of PI environment)..Created user with SAP_ALL profile..I used system without Load Balancing (Parameter, AppServer, SysNo, Logon User, Logon Password, Language and Client)
I was able to test a message from SAP end but still "JCO.Server could not find server function" was the result upon checking sm58.
Did I miss something from my setup and config?

Hi Michal,
I guess there's a big difference with RFC Server Parameters and with RFC Metadata Repository Parameters.
Note: Im using PI 7.1 ehp1
For RFC Server Parameters it includes:
- Application Server (gateway)*
- Application Server Service (gateway)*
- Program ID*
For RFC Metadata Repository Parameters it includes:
- Load Balancing or no Load Balancing (choices)..in here my choice is no Load Balancing
- Application Server*
- System No*
- Logon Language*
- Logon Client*
- Authentication Mode (Use Log-on Data for SAP System or Secure Network Connection for RFC)
if Use Log-on Data for SAP System it includes:
- Logon User*
- Logon Password*
If Secure Network Connection for RFC it includes:
- Quality of Protection
- SNC Partner Name
Looked onto your blogs mentioned several times, but no information on RFC Metadata Repository Parameters.

Unhandled Exception "Could not find any available Domain Controller"

Hi,
I keep on having exchange 2010 loosing contact to domain controllers.
"Unhandled Exception "Could not find any available Domain Controller.". EventID 1. Once I restart the sever, this error disappear and reappear again after a few days.
When I run AD setting, the result shows as below. Update version is currently as at 14.02.0342.003. And boths DCs have 100% uptime.
PS C:\> Get-ADServerSettings | fl
RunspaceId
: 9392eb25-bcdc-462e-816b-2d5626c572a5
DefaultGlobalCatalog
: DC2.com.au
PreferredDomainControllerForDomain
DefaultConfigurationDomainController
: dc1.com.au
DefaultPreferredDomainControllers
: {DC2.com.au}
UserPreferredGlobalCatalog
UserPreferredConfigurationDomainController :
UserPreferredDomainControllers
RecipientViewRoot
ViewEntireForest
: True
WriteOriginatingChangeTimestamp
: False
WriteShadowProperties
: False
Identity
IsValid
: True
Could you please help as this exchange server has our management team and their outlook keep on going offline.
Thanking you in advance.
Cheers,
Pwint

I have another issue. I was trouble shooting exchange bin folder for permission and as a result of it Exchange transport service stopped and couldn't restart. I quickly changed to local service account and able to restart. Fixed the transport roles folder
permission but don't know the password of network service account so I can't change it back. I can send and receive emails internally and externally but I am worried that by running with local account maybe not recommended? Is it safe to reset network service
password? Thanks. I am freaking out... Regards, Pwint

Adobe Premiere Pro could not find any capable video play modules. Please update your video display drivers and start again.

I have administrator rights to the computer. The drivers are up to date. But I am still getting the error message "Adobe Premiere Pro could not find any capable video play modules. Please update your video display drivers and start again" when opening Premier Pro CS5.5. This appears to have happed after I upgraded to Mac OS 10.10.2.
Anyone?
Thanks

Hi Stan.
I had the same problem as you did though I am using Adobe CC. I saw nobody replied to you so perhaps my eventual success on my later version may have applications to the error on your version.
Anyhow, I did all the suggestions found here (Error "Premiere Pro could not find any capable video play modules" | Startup ) first and updated my NVidea card to no avail. Eventually what did the trick was this...
After mucking about with the video card, I said "OK lets just have a go at Premiere itself." So I uninstalled Premiere CC and reinstalled it. Now for some reason it didn't give me the latest patch but a slightly earlier version than the current one but lo and behold it was fine with the video card again. I was able to get my friend's video imported and quickly edited but then was having some issues with exporting where it would hang up but I went into Adobe Media Encoder and exported it there without a care. That task out of the way, I then went and made the update to the latest patch and it works perfectly fine - no video driver issues.
So short of it is this - if you've updated your drivers, perhaps what you could try uninstalling and reinstalling Premiere.
Let me know if this works.
Cheers and good luck

Could not find any capable video play modules [edit]

When I try to launch Adobe Premiere Pro CS6 , I receive the following error:
Adobe Premiere Pro Startup Error
Adobe Premiere Pro could not find any capable video play modules. Please update your video display drivers and start again.
[Title edited for clarity... Mod]

More information needed for someone to help... please click below and provide the requested information
-Premiere Pro Video Editing Information FAQ http://forums.adobe.com/message/4200840
•What is your exact brand/model graphics adapter (ATI or nVidia or ???)
•What is your exact graphics adapter driver version?
•Have you gone to the vendor web site to check for a newer driver?
•For Windows, do NOT rely on Windows Update to have current driver information
•-you need to go direct to the vendor web site and check updates for yourself
•ATI Driver Autodetect http://support.amd.com/en-us/download/auto-detect-tool
•nVidia Driver Downloads http://www.nvidia.com/Download/index.aspx?lang=en-us
Dual video problems - Do you have dual graphics adapters?
Go to the Windows Control Panel and select Hardware and Sound and then select Device Manager... In Device manager you click the + sign to the left of Display Adapters... and see if 2 are listed
IF YES, read below
-http://helpx.adobe.com/premiere-pro/kb/error---preludevideo-play-modules.html
-http://forums.adobe.com/thread/1001579
-Use BIOS http://forums.adobe.com/thread/1019004?tstart=0
-link to why http://forums.adobe.com/message/4685328
-http://www.anandtech.com/show/4839/mobile-gpu-faceoff-amd-dynamic-switchable-graphics-vs-n vidia-optimus-technology/2

CF error: The listener could not find any available service handlers...?

I'm running Coldfusion 8 and Oracle XE 10, both on IIS 7. Every so often, I get this message:
[Macromedia][Oracle JDBC Driver][Oracle]ORA-12519 The listener could not find any available service handlers that are appropriate for the client connection. One possible cause for this error is that the server was not configured for the specified server type (shared/dedicated).
I can restart the OracleServiceXE service and it works fine. However, I have no clue what is causing this. I believe it all began once I started using CFSCRIPTS and running queries using that instead of CFML. I know this isn't a coldfusion forum, but would anyone know what COULD cause this error to happen and what I should look out for? I am new to Oracle and CF btw. Thanks.
Ryan

Hi rpeters83 and 396167,
Did you find a solution for this?
We have ColdFusion 7.0.2 connecting to an Oracle Database 10 R2 and we just got this error when executing a ColdFusion component.
This is the first time we see this error and this CF/Oracle setup has been working fine for a long time.
Thanks.

Server could not find any Meta-Data devices!

Similar Messages

Maybe you are looking for