Server for Web hosting and email (only for 3 domains)

Hello guys,
I want to setup mac mini server for my company which will host only 3 web sites and email server for the moment.
What i got so far,
01. I have Macmini server
02. I have static ip address
03. I have router (vigor 2700) which forward the external ip address (my ip start from 87.197.XXX.XXX) in to my Server using DMZ hosts
(So i have 192.168.1.20 as my server ip address(local) and when i point 87.197.132.48 from out side (using web browser) i can see Mac server page)
So can i setup the server using this infomation. Just want to make sure that i allready got everythign to setup the server.
1st question : Do i have to all information to start this ?
Please help me with this first, then i will have more questions latter.
Thanks in advance

Migrate out of 192.168.1.0/24 (and 192.168.0.0/24) as those will cause problems for your eventual use of VPNs to connect into your network. Most every coffee shop and home network on the planet uses those, and the IP routing inherent in a VPN doesn't appreciate finding the same subnet on both ends of the VPN. The earlier you get your network out of those particular subnets - and preferably over to a subnet somewhere within the 172.16.0.0/12 or 10.0.0.0/8 blocks - the easier the network migration will be.
Set up your internal DNS services and your external DNS services (I'm assuming your local DNS server will not be delegated to serve DNS publicly) and particularly establish an A record in (at least) your public DNS referencing your mail server, and then enter that mail server A record entry as the MX mail exchange host for each of the three domains, and set up three virtual domains on the mail server.
If your gateway is sufficiently capable, you can have a separate domain or subdomain within your network, and have all your "public" names hosted externally. You can then use example.com outside, and example.net inside, and any example.com references from the outside or from the inside will resolve to your external static IP address and (if your gateway has the ability to "reflect" traffic to the public static IP) it'll all work most easily. If your gateway isn't capable, then you can also host the example.com domain internally in your local DNS server, but that means maintaining two parallel sets of DNS entries. Or you can get a more capable gateway. (I did not research your gateway.)
You'll want to read the Apple mail service documentation around alias entries, as there are two ways to do this. See the stuff around pages 73 and 77 in that document. Better still, just skim that mail service administration manual; that'll get you an introduction to the whole area and some familiarity with the general terms and concepts, and that manual is fairly readable.
Then read the TopicDesk Spam Documentation.
If you don't have IT staff around (some of your time, as well as that of others) to dedicate to this mail server management (including user management, troubleshooting, backups, etc.) hosting mail externally can be a good trade-off.

Similar Messages

Possible to make an item editable for certain users and read only for other

Is it possible to make an item editable for certain users and read only for others?
I've been able to accomplish this by taken the select statement that I used to define an authorization scheme, placing it in the Read Only condition of the item. However, I would like to simply reference the authorization scheme to utilize caching, and to help keep things cleaner for future maintenance.
Is it possible to reference an authorization scheme in an item condition similar to the way another item can be referenced by preceding it with a colon (i.e. :P1_First_Name)?

Thank you, your suggestion worked.
It would be nice on a future release of APEX if a drop-down box existed under the Ready Only section that would allow an existing Authorization Scheme to be selected or negated when applying the Read Only attribute to a form item.

Configure DNS on Snow Leopard Server for Web Hosting

Hi Everyone,
I put together an article on my blog about Snow Leopard DNS setup for web hosting. http://www.mkahn.com/?p=279
I'll be revising it over the next few weeks to make it more informative based around feedback. Let me know if you have any questions or trouble setting up DNS on Snow Leopard Server for web hosting.

Thanks for your replies. I realize I'm not making clear the way this network is configured . Also, the only services running on the Snow Leopard server are (at this time):
dhcpd - in the 10.136.31.x range;
dns - same as before;
planned to add are:
Open Directory (for network logins)
Software update;
Web (only on the 10.136.31.x Ethernet);
mySQL (localhost only - for moodle);
NAT is not set up on the Snow Leopard server itself. We have an outside router, a Cisco 2811. This router provides routing for both the public IP range, and the NAT range is configured in this router. The forwarding dns is located in LR and Fayetteville. So what I need is dns on Snow Leopard to forward outside queries to the state DNS servers, and resolve the local NAT IP only for Open Directory and a set of Snow Leopard clients.
Is this going to be possible?

Looking for WEB HOST that I can do servlets and applets on

Hello everyone,
Does anyone know where I can buy web space that will allow me to run a servlet and applet from. I have been shopping today and I had difficutly finding one.

Hmm.... well duffymo. I have gone to a number of sites through Google looking for web hosting sites that support java and I must be picking all the wrong ones to look at because I have only found one in Fremont out of 25-30 that I have looked at.
I guess duffymo you can say what you want in a forum, but usually answering a question with a question isn't very helpful nor appreciated.

I have a second coppy of cs6 design and web premium. Its only for mac and I need it for pc. Can i swap its platform?

I have a second coppy of cs6 design and web premium. Its only for mac and I need it for pc. Can i swap its platform?

From Adobe: "If you have an older version of a product, you must order an upgrade instead of a swap." Because you have a CS6 suite your only option may be to subscribe to Creative Cloud in order to get current cross-platform versions of all their applications. Check here for further info: Order product | Platform, language swap

ColdFusion License for Web Hosting

Can I just buy CF8 Ent and use for webhosting?
I've a bunch of linux hosting. My friends want to rent a few
and use for their CF app but I'm not sure that I can use the CF Ent
that bought from Adobe Store or from a distributor for hosting
services? Or I have to use some special licensing from Adobe for
that kind of thing?
Not sure about that. Because I've heard that MS has many kind
of MS Win Server licensing (web hosting != internal company web
server)
Please suggest!
Jedt S.
Bangkok

More information....
What I've concern is the part in license file of CF8 that
I've (tried) reviewed with my poor English and Law knowledge.
2.7.4 Prohibited Use.
Except as expressly authorized under this Agreement,
Licensee is prohibited from:
(i) using the Software on behalf of third parties;
(ii) renting, leasing, lending or granting other rights in
the Software including rights on a membership or subscription
basis;
(iii) providing use of the Software in a computer service
business, third party outsourcing facility or service, service
bureau arrangement, time sharing basis, or as part of a hosted
service; or
(iv) using any component, library, or other technology
included with the Software other than solely in connection with its
use of the Software. Notwithstanding the foregoing, with respect to
a Production Software License only, Licensee is permitted to host
the Software (including the accompanying Macromedia JRun Software)
for use by persons other than Authorized Users.
The number (iii), last sentence is the a bit curious for me
and my friends.
Any Adobe guys here? Or someone from CFDynamics or cf hosting
services?
Thanks in advanced!

Strange info in "Bypass Proxy Settings for These Hosts and Domains"

For my Mac Mini my Network IP Address always has a self-assigned 169.254 number that I cannot change. Strangely, this same IP number is similar to info that is in the Proxies section (of Network Settings) under "Bypass Proxy Settings for These Hosts and Domains".
No matter what I do, this info (*,local, 169.254/16) appears in my Network Settings in the Proxies section under "Bypass Proxy Settings for These Hosts and Domains". (I tried removing the info and it would cause the "Configure Proxies" selection to default to "Always Use PAC File". Had to go back and retrash all the plist files to have Proxies go back to "Configure Proxies-Manually". Still, the info (*,local, 169.254/16) continues to appear in the "Bypass Proxy Settings for These Hosts and Domains" section and my IP address is always a 169.254 number.)
Comcast cable modem via direct hardwired Ethernet works fine with my other computer, so not the modem. Also, other computer does not have any info in the "Bypass Proxy Settings for These Hosts and Domains" section.
Installed a fresh copy of OS X 11.5 on a new hard drive. Still the same problem.
I posted this issue before but only got one responder and the problem still exists. Any clues? Somebody must know about this stuff. Help please.
Thanks

When your Mac wakes up, it does not yet have an IP Addresss. It wants to send a request to a Router for an apprpriste IP address to use now. But it needs to have an IP address (like a return address) to receive any messages. So, ... wait for it,
... it (your Mac) makes one up. There are rules that ensure it is a random address, but they always start with 169.254. It is on the same subnet with any low-order 16 bits This is the "self-assigned" range of IP Addresses. This address is only good for talking on a local network segment, for things like asking for a valid IP Address from a DHCP-enabled Router.
In most cases, on most networks, the 169.254 self-assigned IP Address is replaced by a valid Local IP Address such as 192.168.xxx yyy or 10.0.xxx.yyy so quickly that you never even see the 169.254 Address.
If you do see the 169.254 Address, it can be read as "Nobody will talk to me" or "Nobody will give me an IP Address". When you have this IP Address for more than an instant, you should suspect bad cables for Ethernet connections, bad signal strength or interference for wireless, Router configuration problems, or Mac configuration problems.
Mac configuration problems are often solved by using the "Assist Me" button is System Preferences > Network and choosing to set up again.
Another diagnostic is to try using Network Utility and the Ping function, and Ping-ing the address of your Airport base Station, often 192.168.0.1 or 10.0.0.1 or similar. This will tell you if the Router is reachable, or there are cabling/wirelss signal problems.
In this case, proxies are not an issue, and are simply a distraction from the real problems.

When I add pictures into MUSE , do the pictures resize for web quality (And so the page loads fast enough) or do I have to do this using an external software like photoshop, etc. ? Thank You

When I add pictures into MUSE , do the pictures resize for web quality (And so the page loads fast enough) or do I have to do this using an external software like photoshop, etc. ?
Also is there any way I can change the contact form email for all of my contact forms at once.
I have over 100 contact forms and i want to make them reach the same email anyway I can do that without going one by one?

If you have placed the image in Muse using File > Place and then scaled the image down in Muse while editing, then Muse publishes/exports the scaled down/optimized image in final output. When using as a Fill, the output size depends on the Fitting option you setup in the Fill options.
As for the contact form email, you would need to specify the email address for each form individually. There is no workflow to edit the same for multiple forms at a time.
Cheers,
Vikas

VIrtual host and reverse proxy FOR EBIZ R12.0.6

we have 4 dev EBIZ instances on a single hp_ux itanium server on which I have to setup one instance for virtual hosting and to work behind a reverse proxy .
any particular documents or steps for this.
Thanks
mn

we have 4 dev EBIZ instances on a single hp_ux itanium server on which I have to setup one instance for virtual hosting and to work behind a reverse proxy .
any particular documents or steps for this.Implementing Virtual Host, Concurrent Managers and EM DBconsole on Oracle Applications R12 [ID 603883.1]
Conc-System Node Name Not Registered After Fresh Install Using Virtual Name [ID 948644.1]
Is Auto Failover With Virtual Hostnames For Concurrent Processing Servers Supported In 11i Or R12? [ID 456540.1]
Case History: Implementing a Reverse Proxy Alone in a DMZ Configuration - R12 [ID 726953.1]
Oracle E-Business Suite R12 Configuration in a DMZ [ID 380490.1]
Thanks,
Hussein

Reset iPhone asks for Apple-AD and then asks for password for other Apple-ID (my old, before I changed the email adress)

Reset iPhone asks for Apple-AD and then asks for password for other Apple-ID (my old, before I changed the email adress). Never had this problems before and I have reseted it once or twice since changing emailadress on the Apple-ID.

sckofusernames77 wrote:
but it doesn't ask you if you have one or say that you won't be able to log on without one.
Well, it does say on http://www.apple.com/icloud/setup/pc.html in step 1: "To enable iCloud on your Windows PC (Windows 7 or 8 required), first set up iCloud on your other devices, then install the iCloud Control Panel for Windows.
If you're trying to back up your device to iCloud, that doesn't have anything to do with your computer. You back up to iCloud over wifi. All you do is go to Settings>iCloud, sign in with your Apple ID to create your account, scroll down and tap Storage & Backup, then turn on iCloud Backup. You can then tap Back Up Now at the bottom to start the back up manually, or lock the screen and connect it to your charger and it will back up automatically every day.
Enabling the iCloud control panel on your PC only allows you to sync your iCloud data with your PC, not to back up your device to iCloud.

I have had my iPhone 4 for a year and have only plugged it into my friends computer when I first got it, and now I just purchase my music right on my phone, so now I'm getting a new phone so if I plug it into my comp will anythin get deleted?

I have had my iPhone 4 for a year and have only plugged it into my friends computer when I first got it, and now I just purchase my music right on my phone, so now I'm getting a new phone and want to back up my music, photos, etc so if I plug this phone into my computer will anything get deleted off my phone?

See Here:
IOS Sync Content to Computer
http://support.apple.com/kb/HT1296
And have a Look here Before you do Anything...
http://www.apple.com/support/iphone/getstarted/
This might be Useful:
iPhone User Guide
http://manuals.info.apple.com/en_US/iphone_user_guide.pdf

WLC: which software-version support SHA2 certificates for Web Authentification and Web Management ?

Hello,
I tried to install new SHA2 3th-Party certificates on our WLCs. There are old WiSM1-Boards and 2504 to support our old 1230 Access Points, running 7.0.251.2, which didn't install it, although the config manual for 7.6 and 8.0 say that SHA2 certificates are supported since 7.0.250.0. When I tried to install the SHA2-certificates I get the message "File transfer failed" an the log says:
*TransferTask: Dec 12 13:22:14.394: #UPDATE-3-CERT_INST_FAIL: updcode.c:1869 Failed to install Webauth certificate. rc = 1
*TransferTask: Dec 12 13:22:14.394: #SSHPM-3-KEYED_PEM_DECODE_FAILED: sshpmcert.c:4085 Cannot PEM decode private key
I tried to install the same certificates on our WiSM2-Boards, running 7.4.121.0 and I failed too. The same certificates could be installed on a 2504 running 8.0.100 without any problems.
In all 3 cases I tried to install unchained certificates for web management and Level 3 chained certificates for web authentication. I used the following guides to get the certificates (e.g. taken from the config manual 8.0.100):
http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/109597-csr-chained-certificates-wlc-00.html
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/70584-csr-wlc-00.pdf
Which software versions support SHA2 certificates and which didn't ? Is the a list for it ?
Regards

Hello,
I solved the problem. First I used a Debian Linux system with Openssl 1.0.1. After I searched the internet using one of the log messages above I found sites which mentioned to use Openssl 0.9.x. So I tried a productive and security fixes Debian Linux System running Openssl 0.9.8 and I succeeded. The wlcs accepted the certificate files and used it after a reboot. The Web GUI still shows a SHA1 Fingerprint, but the certificate signature Algorithm is SHA2:
Signature Algorithm: sha256WithRSAEncryption
When you check the openssl.org homepage Openssl 0.9.8 is still one of the actual version of openssl and is still available and fixed. But the Openssl Roadmap says:
"We don't want to have to maintain too many branches. This is likely to include a timescale for the EOL of version 0.9.8"
I don't know the differences between certificates made with openssl 0.9.8 and 1.0.1. Is there anybody who can explain it to me ?
Regards

Im am trying to set up my printer for web services and it is asking me for a proxy address

im am trying to set up my printer for web services and it is asking me for a proxy address

Have you downloaded and installed an App Store app that you downloaded free from some website instead of from the App Store? If so, that's a stolen app, and you need to delete it.

I bought a used macbook pro from a friend. Software updates are available, but when I try to update, the computer asks for apple id and will only accept the former owner´s. How can I connect my macbook to my apple id?

I bought a used macbook pro from a friend. Software updates are available, but when I try to update, the computer asks for apple id and will only accept the former owner´s. How can I connect my macbook to my apple id?

The first thing you should do after acquiring a used computer is to erase the internal drive and install a clean copy of OS X. How you do that depends on the model. Look it up on this page to see what version was originally installed.
If the machine shipped with OS X 10.4 or 10.5, you need a boxed and shrink-wrapped retail Snow Leopard installation disc, which you can get from the Apple Store or a reputable reseller — not from eBay or anything of the kind.
If the machine shipped with OS X 10.6, you need the gray installation discs that came with it. If you don't have the discs, order replacements from Apple. A retail disc, or the gray discs from another model, will not work.
To boot from an optical disc, insert it, then reboot and hold down the C key at the startup chime. Release the key when you see the gray Apple logo on the screen.
If the machine shipped with OS X 10.7 or later, it should boot into Internet Recovery mode when you hold down the key combination option-command-R at the startup chime. Release the keys when you see a spinning globe.
Once booted from the disc or in Internet Recovery, launch Disk Utility and select the icon of the internal drive — not any of the volume icons nested beneath it. In the Partition tab, select the default options: a GUID partition table with one data volume in Mac OS Extended (Journaled) format. This operation will permanently remove all existing data on the drive, which is what you should do.
After partitioning, quit Disk Utility and run the OS X Installer. When the installation is done, the system will automatically reboot into the Setup Assistant, which will prompt you to transfer the data from another Mac, its backups, or from a Windows computer. If you have any data to transfer, this is usually the best time to do it.
You should then run Software Update and install all available system updates from Apple. If you want to upgrade to a major version of OS X newer than 10.6, buy it from the Mac App Store. Note that you can't keep an upgraded version that was installed by the previous owner. He or she can't legally transfer it to you, and without the Apple ID you won't be able to update it in Software Update or reinstall, if that becomes necessary. The same goes for any App Store products that the previous owner installed — you have to repurchase them.

My iPad 1 won't hold a charge for very long and will only fully charge when turned off while plugged in. Will a full reset fix this?

my iPad 1 won't hold a charge for very long and will only fully charge when turned off while plugged in. Will a full reset fix this?

maybe but
most likely no
if you have many apps running and using data and localization at the same time yes maybe
but batteries get worse and worse and worse over time until they die a software reset will not change that

Server for Web hosting and email (only for 3 domains)

Similar Messages

Maybe you are looking for