Server Interrupted for USB External HDD

does anybody know how to reconnect an external hd on AEBS w/o having to restart? this happens sometimes to me when i'm working on the external HDD via AEBS it will come up w/a dialog box asking to disconnect all drives...how do i reconnect it w/o having to restart my laptop?

From searching the web, I am tempted to say the Iso Gear is quite an exotic device.
It's up to Astone them to deliver a firmware upgrade for their device to work with Mac OS X 10.5, as Apple probably follows USB 2.0 standards when accepting (or not) an external hard drive.
diskutil became more picky in 10.5 (been bitten myself) but still, I am not sure whether this is due to Apples development teams faults or due to to Astone following standards.
There has been an issue in 2006 with LaCie drives on OS X 10.4 which were resolved by their firmware upgrade.
I know this is of no help to you, but consider not just talking on Apple forums about this but also on Astone help channels.
--greg

Similar Messages

Installation of Windows 7 via USB External HDD (Boot Camp Assistant)

How do I mount Windows 7 Ultimate disk image (.iso) onto my USB external HDD so that I can boot using that USB external HDD? I have tried reEFIt, but it doesn't work for me. It may be because I did something wrong. I would appreciate a comprehensive guide. Thanks.

i suspect you haven't prepared the USB drive as a boot volume.
You can absolutely do this. It is detailed on CNET in the following article: http://reviews.cnet.com/8301-31012_7-20020513-10355804.html

Automount of SD card & USB external HDD with strange KDE pop up msg

Today I reviewed lots of threads posted over the last year and some bug reports too about this issue, but it's happening for me too. Both SD card and USB external HDD have autodetectable filesystems on them because I can mount them by hand with "mount /dev/mmcblk0p1 /mnt" and "mount /dev/sdb1 /mnt". But it would be nice if I didn't have to do that.
Although I didn't notice which explicit install that I did pulled them in as dependencies, I do have udisk2 and polkit installed. Also installed udiskie as a wrapper. I've been mounting these volumes by hand before now because I feel like I'm still learning the ropes of The Arch Way and guessed (apparently incorrectly) that mounting volumes by hand was just part of "The Arch Way". But based on some threads here and some bug reports, I guess this used to work in Arch but has been causing some problems for some people lately when they upgrade. I just installed Arch for the first time (using the 2015.02.01 iso image), so I don't have any background to go on.
So what is The Arch Way for automounting external drives? I've skimmed the wiki article for this and because "Development of udisks has ceased in favor of udisks2." it seems that udisks2 is preferred. But it got installed and the daemon is running for me. The user is in the wheel group. dbus is running (though like one person who filed a bug, I too have several instances of dbus in my ps -aux output and I'm not sure if that is as it should be or not). I've done no special configuration ("not wittingly" anyway; I promise, my name is not James Clapper) that I think would have affected this.
So for a newb with no special preference, how should automounting be configured in a new Arch system? In other words, what should be my first steps in trying to solve this problem for myself? I know there are lots of different ways to skin this cat, but I'd prefer the simplest and most elegant solution that does not depend on KDE or GNOME or other unnecessary tools. I've just (with this Arch system I just installed) begun using i3wm and I think I'll be sticking with it. That said, however, it's clear that I inadvertently/unwittingly managed to get some elements of KDE into memory as the following http://gamonics.org/img/2015-02-26-1731 … _scrot.png shows. This popped up both times, when I plugged in my SD card and when I plugged in my USB drive. Any thoughts on what's going on here? I did install okular explicitly because I think it's one of the best PDF viewers, but I don't understand why KDE is reporting anything to me when I'm running i3 and insert an SD card or a USB disk.
And in the terminal, I get this output (apparently from udiskie):
[root@archippocrates archie]# Failed to show notification: The connection is closed
not adding /org/freedesktop/UDisks/devices/mmcblk0: unhandled device
mounted /org/freedesktop/UDisks/devices/mmcblk0p1 on /media/3532-3338
Failed to show notification: The connection is closed
Although the volume does get mounted automatically.
Thanks for any thoughts.
-- mod edit: read the Forum Etiquette and only post thumbnails http://wiki.archlinux.org/index.php/For … s_and_Code [jwr] --
Last edited by Gamonics (2015-02-27 00:25:01)

I personally can't answer the question of "simplest and most elegant" way of mounting devices. It all depends on what you want. If you expect more exotic functionality, say correct unmounting of devices if they were disconnected during a sleep cycle, there's probably no way around udisks2. For that you get a complex piece of software prone to... unexpected behaviour. Mind you some of it is related to front-ends like GVFS.
As to your KDE issues, last I checked mount handling was disabled by default there, but you can control it manually (see man kcmshell4). Though I haven't followed up on KDE 5 developments. If going with udisks2, I'd recommend using devmon from the udevil package as a front-end (more details on the wiki udisks page).
PS: multiple dbus instances are expected, check the user names and specified arguments in the ps output.
edit: grammar. :X
Last edited by Alad (2015-02-27 17:03:31)

USB External HDD Enclosure with a 500GB HDD!!

Hi All,
I was just wondering if anyone has come across using a 3rd party USB external HDD enclosure with a hard drive (mine is 500GB HDD). What I am trying to do is to format the HDD so both PC and MAC can use it but it will be mainly connected to my iMAC. I have tried by using PC to format the HDD to NTFS but MAC will not show the HDD on the desktop when I plug the USB to the back of the iMAC.
I have done some researches and it seems the only way to do make this possibe is to format it into FAT32. So I have tried to use FDisk to make the partition but it doesn't seems to support anything bigger than 120GB, now I am really stuck. If anyone knows any quick and painless solution, please spare me some advice.
Headache!!
Dave
iMAC 20" Core2 Duo 2.16 1GB Mac OS X (10.4.9) Mac OS X (10.4.9)

Windows can use, but not format, large FAT32 partitions. Microsoft wants to discourage using FAT32 for portable storage (for marketing reasons).
The solution is to use Mac's Disk Utility to format the disk as FAT32 (misnamed MS-DOS in Disk Utility). The disk will then be read/write by both Mac and PC.
Also, it's worth pointing out that you can read and write NTFS disks using MacFUSE with the NTFS-3G plugin. Albeit, this is very awkward to do unless you've got some UNIX shell experience.

How do I get rid of the SPAM Popup Ad for an External HDD

A spam popup ad for an external HDD came down with supposed Lenovo system updates. This ad pops up every few hours and I can figure out how to get rid of it. There is a check box that says 'don't show again' but I check it and it doesn't work. I am extreemly disappointed they have invaded my system with an ad that was part of a system update. I have 15 thinkpad users and it hasn't happened to all of them yet but they'll be screaming at me when it does.
Solved!
Go to Solution.

How do I disable this crap?
http://i183.photobucket.com/albums/x57/UrsusMorologus/lenovo-desktop-spam.jpg

Twin unpowered USB hub for connecting external HDD and iphone

I have a MBA and a powered Kensington 7 port USB hub which works great when I am either at home/in the office.
Is there an unpowered twin port USB hub that would allow me to connect both my WD myv passport 320gb external HDD and 3g iphone to my MBA when i am truly on the move?
thanks in advance
Message was edited by: NRG1970

Because those are both drawing power from the macbook air, it might be questionable, but any should do, but I haven't seen any 2 port hubs, only four port ones, and I tend to like Logiix, as their support is good and their products are good also, and they are fairly low profile.

How to transfer my archlinux.vdi on an usb external hdd

Hello everybody from Mauritius ~!
I am Caron from Mauritius. I run Mint 17 Quiana 64 bit and an Archlinux Vm. My aim is to convert my archlinux vdi into a bootable external hdd ( I use a laptop so I'll be using a laptop external hdd in a usb casing.)
I read that I had first to convert the .vdi into a .raw and then use dd command. Unfortunately I failed because the commands are not working- unable to find the .vdi on my system. :?
Can u help please ?
Thanks in advance.
Caron
p.s : I use a Dell Laptop Vostro 1015

Hi everybody and sorry for the delay...
First please note that Mauritius is a former ENGLISH colony till 1968 and is now known as the REPUBLIC of MAURITIUS. I invite you all to vist it as soon as you can.
To be more serious, I abandonned the Arch vdi cloning and tried to setup archlinux on an external usb hard drive ( laptop 500 gb hdd in a SATA enclosure ) .
Arch recognised the disk as /dev/sdc and I did the install twice , having partitionning the hdd before on gparted.
I think that I am basing my setup process on a virtual box tutorial ( youtube ) but when I reboot the system and choose the option " boot on existing Os " : nothing happens.
Is it because the command " vbox echo >> /mnt/hostname " affects the boot sequence . ERROR MESSAGE is " APM not present ".
It's a pity becase all other distrib such as Kali, Ubuntu and even Cylon install far more quickly and easily on the external usb hdd ?
Thanks again for your time, patience and support
Caron

Can you buy firewire cable for usb external?

i recently bought an Iomega external HDD for time machine, it's a usb based drive, i really regret it because it's so slow. Could i just buy a firewire cable and use it on the drive so it can go faster?

I've got four external FireWire 800 drives attached to my G5 tower. I installed a second FireWire PCI Express Card on the G5. They pretty much rip over the USB 2.0 I had before.
Only comment I have is that if you use Time Machine and a FireWire 800 drive, make sure that it is connected directly to a Mac FireWire 800 port and not daisy chained to any other device. If it is daisy chained, you may get one of two issues - a very very very slow initial backup with a potential failure to backup. I learned the hard way and when I direct connected my backup drive to its own port, it cut the initial backup time by 75 percent and did not fail.
I use my Mac for my work and have a lot of applications and data so it took about five hours to run the initial back up. Without the direct connect, it ran for about 26 hours and failed near the end of the attempt.
Just one man's experience, hope this helps.

USB External HDD not recognised in OSX 10.5.4

Hi,
I am attempting to use an ISOGEAR250 2.5" IDE external HDD on my iMac.
This deviceis advertised as 'compatible with OS/X', which is in fact only true up until version 10.4.9.
The device is not detected on any OS/X version with the IOUSBMassStorrageClass.kext or IOUSBfamily.kext kernel extensions of any version of OS/X past 10.4.9.
The only way to get this device to detect on Leopard is to revert the specific kernel extensions to earlier versions, and use the USB Prober utility. This is quite a dangerous exercise, and can lead to operating system instability.
I have tried the device on numerous Apple computers, and it only works on the ones with OS/X 10.4.9 or earlier installed. I have also experimented with many different file system formats. This device works fine on Windows machines, including Windows in Bootcamp, and Windows using VMWare or Parallels.
For your information, the device does turn up in the System Profiler with the following info, but will refuse to mount with kernel extensions past version 10.4.9:
USB4500 FW1.04:
Version: 0.001
Bus Power (mA): 500
Speed: Up to 480 Mb/sec
Manufacturer: DATAST0R Technology Corp
Product ID: 0x4500
Serial Number: 1966XXXXXXXXXXXX (I added in the X's)
Vendor ID: 0xed06
If I plug the HDD in while my iMac is sleeping, it will wake up the iMac.
I have tried the device on both the iMac's built-in USB ports, as well as with a powered USB hub.
Numerous other users have had similar of the same problem
(see: http://discussions.apple.com/thread.jspa?messageID=7835455), and yet Apple has not yet rectified the problem, which is clearly arising from the update to the operating system, and not the device itself.
Does anyone have a fix for this problem, aside from reverting the kernel extensions and using the USB prober?
Thanks for your help,
Cal

From searching the web, I am tempted to say the Iso Gear is quite an exotic device.
It's up to Astone them to deliver a firmware upgrade for their device to work with Mac OS X 10.5, as Apple probably follows USB 2.0 standards when accepting (or not) an external hard drive.
diskutil became more picky in 10.5 (been bitten myself) but still, I am not sure whether this is due to Apples development teams faults or due to to Astone following standards.
There has been an issue in 2006 with LaCie drives on OS X 10.4 which were resolved by their firmware upgrade.
I know this is of no help to you, but consider not just talking on Apple forums about this but also on Astone help channels.
--greg

Win XP wont recognize the 400GB USB external HDD

I just bought a external 400gb hdd from toshiba,
usb 2.0
no psu
says plug and play right on the box and windows xp wont recognize it.
The little blue led comes on, but nothing works at all.
The only thing that happened once, is I THINK xp recognized it as an MTP device.. which I got updates for, but still nothing.
I updated all my drivers, nothing seems to be working at all.
Please let me know how I can go about making this work.
Thanks

> The only thing that happened once is I THINK xp recognized it as an MTP device which I got updates for, but still nothing.
What MTP means exactly?
Did you check if the external HDD needs an additional power supply?
Did you test it on different computers/notebooks?
Did you try to remove the HDD hubs and controllers from the device manager and rebooted the notebook in order to reinstall this devices??? If not -> do it

Access USB external HDD connected to Airport Extreme

Hi.
Today I configured "Back to my Mac" and I'm having a little issue with the external HDD that is connected to the Airport.
Let me explain the configuration: Airport Extreme (latest version) configured with Back to My Mac option, with an external HDD connected using USB port (The HDD is externanly powered). iMac computer with OSX Mavericks wireless connected, configured with iCloud Account and Back to My Mac with screen sharing).
I can access the shared screen and control the iMac from my Macbook Air outside my home network.
The issue is when I try to access the "network HDD" because I can connect using the right user but Finder windows never shows the HDD content. I have to disconect and reconnect to the external HDD to be able to see the files (If I have 3 windows and want to access the HDD on each of the 3 windows, I have to disconnect and reconnect 3 times).
Question:
There is any way to access the external HDD and be able to see its content using the configuration mentioned? The disconnect and reconnect procedure for each window is normal? There is a better configuration I can apply?. Just as information, from my MacBook Im able to see perfect the HDD content from outside my home network.
I know the question is a little bit confusing, but if you need any additional info please let me know.
Thank you.

Does this help?
http://apple.stackexchange.com/questions/117135/access-disk-attached-to-airport- extreme-over-internet

M30-841: recognition of an USB external HDD

Hello !
My portable is a M30-841 with Windows XP Home Edition SP2 (and with automatic updates). Note that there are no exotic softwares installed.
I have a problem with an external hard disk purchased recently.
It is in an USB 2.0 box, plugged by a cable on a USB connector of the Satellite.
When the Windows session starts, the disk is not activated :
A little image at this point : http://black-winny.site.voila.fr/images/Etat_du_disque_au_lancement_de_Windows.png
If after that, I unplug and replug the cable... the disk is activated and its letter (G: ) is found :
A little image after replug : http://black-winny.site.voila.fr/images/Etat_du_disque_apres_rebranchement.png
Nota : The problem doesn't occur with this kit used in the same way on another computer (my home computer).
Do you have a solution to suggest for a correct activation when Windows starts .
Great thanks !
Jacques (from Paris, France)
Message was edited by: Black-Winny

Hi Jacques
I have two external HDDs (30 and 60 GB) and both of them work with different notebook models. I connect it always when Windows is loaded completely and disconnect it before the unit shuts down. On this way the operating system will detect new hardware and after just a few seconds it can be recognized properly.
Please test it on this way. I am sure that it will work well.

Booting from USB external HDD on Satelite L30

Hi,
Is it possible to boot winxp (pro, sp2) from external HDD case connected by USB?
Some previous topics suggest that it is not possible (officially), but one (http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=21996) says that it is. I have tried to search for mentioned method, but with no results (maybe because english is not my native language).
It is very important for me, and I would really appreciate if anyone could give me a hint.
Second question is about "plus" before HDD boot option in BIOS (Phenix afair). Is suggests it is possible to connect more then one disc - if so, then how? Inside laptop, of course, there is no additional room...
Thank you in advance!

Hi
> I have tried to search for mentioned method, but with no results
As the other threads already suggested its not possible to boot from the external USB HDD. You can boot from HDD, CD/DVD, FDD, LAN.
The external USB FDD can be connected to the notebook and you could boot into the dos from the diskette.
By the way; this notebook does not support select bay and you cannot insert a second HDD

Toshiba 500gig usb external HDD disconnects at the drop of a pin

Hi,
I have one of the new USB powered portable usb drives from Toshiba. It is a 500gig unit. It has worked flawlessly up until about the last couple weeks. Since this time is disconnects very easly and sometimes is not useable because it disconnects too much. Is this a common problem with these smaller drives that connect with the regualr usb cord, and is there any fix for it?

Some people find that these types of drives need more power than a single usb cable can supply. The Western Digital Passport also has this problem. Using a Dual USB cable helps a lot in this situation by drawing power from two USB ports instead of one.
Addendum Friday 1:30 PM CDT: Just make sure that the dual cable you get has the correct plug for your external hard drive. The one I linked to above works with the WDC Passports, but I do NOT know if it has the correct plug for the Toshiba External Drives. I would advise against using one that works as an extension to the existing cable as the additional connection combined with the additional length would probably defeat the purpose due to the power loss they would bring into the scenario. You need a cable that attaches directly to the USB ports on the laptop and the external drive.
If you don't post your COMPLETE model number it's very difficult to assist you. Please try to post in complete sentences with punctuation, capitals, and correct spelling. Toshiba does NOT provide any direct support in these forums. All support is User to User in their spare time.

Can I connect two USB external hdds at once?

Can I connect two external hdds by USB at once and then transfer between the two?

Yes. The practical limit is 126 drives (you need the appropriate USB hub to do that, of course )

Server Interrupted for USB External HDD

Similar Messages

Maybe you are looking for