Server name not showing up in Chooser

mac OS 10.1.3 server. The server name is not showing up in the Chooser,. I can get to it by typing in the IP address, but this is a pain for my teachers.
It showed up for a long time, but now it will not show up.
Any ideas?

Apple talk is on the server and the clients. I also have another server that is connected to the same switch and it can be seen in the chooser. So I do not think it is a config problem with the switches or hubs. I have not changed anything (that I know of). I have researched this and can not find anything on it.

Similar Messages

  • Server name not showing up in shared list.

    Wondering if anyone may know what's up with this.  We have a mac mini server with Yosemite server on it.  The name for the server isn't showing up on the client computers in the office in the "Shared" list of computers in the Finder.
    Any ideas?

    Apple talk is on the server and the clients. I also have another server that is connected to the same switch and it can be seen in the chooser. So I do not think it is a config problem with the switches or hubs. I have not changed anything (that I know of). I have researched this and can not find anything on it.

  • HT1451 Why do the song names and cd name not show up on the IPod Shuffle?

    Why do the song names and cd name not show up on the Shuffle?

    MysticChyk wrote:
    Why do the song names and cd name not show up on the Shuffle?
    Err this is no longer April 1st you know.
    The iPod Shuffle has never had a 'display' on which track names can be shown. See http://www.apple.com/ipod-shuffle/ if you want an iPod which does have a display on which you can see the tracks names and even the album cover art then look instead at the bigger and more expensive iPod Nano http://www.apple.com/ipod-nano/ or iPod Touch http://www.apple.com/ipod-touch/
    PS. The current iPod Shuffle even though it has no display on which it can show the track names can read them out loud to you using a voice-synthesiser this is the VoiceOver feature described on the iPod Shuffle product page I listed above.

  • The report I published on the SQL server report server is not showing in the application we use to retrieve reports.

    The report I published on the SQL server report server is not showing in the application we use to retrieve reports. My cell phone number is {removed}
    Thanks.

    Hello Roger Tenn,
    Thank you for posting in the TechNet Forum.
    As this issue is related to SQL server report server, to receive better report, it is recommended to ask in the SQL server forum.
    https://social.technet.microsoft.com/Forums/en-US/home?category=sqlserver
    The professionals here will be glad to help you.
    Best regards,
    Fangzhou CHEN
    Fangzhou CHEN
    TechNet Community Support

  • Essbase server is not showing in the windows services (11.1.2.1)

    Hi All,
    Essbase server is not showing in the windows services 11.1.2.1. when I checked the processes from task manager it is there.
    Regards,

    The windows service for essbase in 11.1.2.x is an OPMN service "Oracle Process Manager..."
    Cheers
    John
    http://john-goodwin.blogspot.com/

  • Picture names not showing in iphoto+mail

    I recently updated to ilife ´08 and can´t figure out how to get the actual data names to show. I don´t sant to see titles,ratings and keywords.. I want to see the actual names of the pictures. Also when I hit the mail button in iphoto the pictures are put in the mail... without the pictures name. If I drag and drop the pics to a desktop folder the names ar5e of course correct. But many of the people I send mails to are not even aware how to drag and drop. If I send someone an email with 40 pictures to chose from,I want them to see the names underneath the pictures in the email without having to drag and drop. This was always how it worked in ilife ´07 and it makes choosing the pictures and telling me which ones they want in high quality a very easy process. I can´t even figure out how to sort the photos by "NAME". If there is no way to change it then I will be going back to the older version. Sometimes "improvement" is not a good thing.
    Does anybody know how to do this?

    When you select a pic to Email in the iPhoto Window and hit the email button you have the option to include title and comments with the photo.
    Uploaded with plasq's Skitch!
    In iPhoto you have two concepts that are related:
    Title is a name that you give to a photo in iPhoto
    Filename is the name of the file that contains the photo.
    Which are you referring to when you say "name"?
    Regards
    TD

  • LMS 4.2.3 variable name not show in drop-down list

    Hi all,
    I am trying to use performance threshold to trigger a script whild device CPU or Memory high.
    There is a default threshold template called "CPU Utilization" and "Memory Utilization".
    After I choose either one, there should be one or two variable name in drop down list.
    But I only see "Select MIB Variable" in the list.
    I try to create a template with exact the same variable but still got nothing in the list.
    The strange thing is that no all the default template has this problem.
    I can see variable name under some template like "Device Availability" or "Port Availability"
    And this is not browser problem because I try both IE and Firefox.
    Any one how to solve this?

    Thanks for your advice.
    Now all my devices are connected in Layer View [Devices View], but User Tracking still not shows me informations from several switches about hosts. Its works like randomizer. Now 5 devices form User Tracking  don't show me informations.[WS3550 2 devices and 2  WS-C2960S-48LPS-L]. In lists devices Acquisition Action i check acquisition for this 5 devices. After that acquisition complete, but User Tracking still empty ( all ports on this devices are active).
    SNMP, Credentials all is good.
    I try resolve this problem many days, but without results. Its semmes like a bug.
    ANy propositions?

  • Host name not showing up under Active Clients

    When I go into my router and check active connections, I can see all host names like "Acer Laptop", "IPhone" etc..., IP and MAC address' that are connected to router. Today, when I was in there looking, I saw an asterisk where host name should be for the TouchPad. (it took me a while to figure out it was the TouchPad) Is there a reason why Host name would not show up?
    I have gone into "Device Settings" and set "Name" as "Chucks TouchPad". Is that the host name that should be showing on router?
    Thank You for any assistance.
    Post relates to: HP TouchPad (WiFi)

    Sure is, but it will involve some commandline work. First, you're going to need to install the SDK. You only need the Novacom part of the SDK, but AFAIK there's no seperate download for Windows... you have to get the whole thing. The SDK is available here: https://developer.palm.com/content/resources/devel​op/sdk_pdk_download.html
    Next, you're going to need to enable Developer mode on your TouchPad, here's how to do that:
    Start a Just Type search and enter webos20090606
    A Developer Mode icon will display, tap it
    Tap the toggle switch to turn it On
    Leave the password blank and tap Sumbit
    Close the Developer Mode app
    Now, connect your TouchPad to your computer. Next, you're going to find a file called Novaterm.bat. It's buried in the install directory of the SDK. I don't remember the exact path (I don't use Windows anymore) but it's something like C:\Program Files\Palm SDK\Current\bin (keep digging around for bin folders in the C:\Program Files\Palm SDK path and you'll find it eventually). Doubleclick that to start a nice little terminal app. Choose your TouchPad from the drop down list and click connect.
    Now, time for some command line stuff. Run the following commands in the terminal:
    mount -o remount,rw /
    cd /etc/dhcp
    vi dhclient.conf
    Press the I key on your keyboard to go into edit mode (this is a Vi specific thing)
    Remove the # at the beginning of line 14 and change the andare.fugue.com inside the quotes to whatever you want your TouchPad reporting as. For example: #send host-name "andare.fugue.com"; would become send host-name "RidiusTouchPad";
    To save your changes, hit the ESC key (to exit edit mode), then type :wq and hit enter. Note there is a colon in there. Again, this is Vi specific stuff.
    sync
    mount -o remount,ro /
    Once you've done this, disable and re-enable your Wi-Fi and your TouchPad should be reporting a hostname. Kind of a lot of work if you ask me (unless you already have the SDK installed).

  • Server Name not found on Servers' List

    Hi,
    I have an installation on SAP B1 8.8 on which the server and 3 of the four clients are operating normally. The fourth client (ran on Windows 7) is not showing the server name on the "Company Select" form. Instead of it it is showing only "(local)". As a result, of course, the list of companies shown below is empty. I tried to re-install but with no good.
    Again, the other clients on the network are working fine.
    Does anyone have faced similar situation?
    Thanks
    Gerasimos

    hi Gerasimos,
    Greetings of the day.
    which windows 7? 64 bit or 32 bit?
    first of all do a clean uninstall.
    delete all SAP folder in c:\program files, c:\common files\business objects.
    delete all SAP folders from application data coming under documents and settings for all users, administrators.
    delete all temp files under c:\windows, documents and settings\ each user and\or administrators\local settings.
    download msicuu2.exe from microsoft.com, install and run it, will clean registry if anything available.
    install SAP B1.
    then go to LAN adaptor settings, under network settings, under IPV4 and in adapter settings, specify the static IP address if any and in the default gateway specify the IP address of the server.
    uncheck IPV6.
    start SAP B1
    it should work.
    let me know.
    thanks and regards.
    Vijay M. Patil.

  • Contact name not showing in call/sms log even when I call/sms from my address book.

    Two things have changed on my phone recently.
    1. I ran the latest update 4.3.2
    2. My phone was not showing all the contacts in my address book that is in my Mobile Me account. Mobile me had 166 contacts. The iPhone 4 had 136. I I unchecked the syncing of my contacts on my phone. This removed all the contacts from my phone. Then I check the syncing options again. All 166 appeared on the phone.
    I'm not sure which of the two caused the issue but now anytime someone who calls their name does not appear on the display or log, just their number. I can even call people from my address book and the display shows that I am calling them with their name and photo on display. However, in the call log the name does not show just their number.  This applies for text messages. I send a message directly from within the contact card in the address book and in my text log it shows only the number and not the name.
    I've turned the phone off and on a couple of times.
    I would appreciate any advice.
    Cheers

    Thanks iraghib,
    In the end I reset my phone to factory settings. I created a back up of my address book and ical. Reset the phone and did a sync again. This fixed it all. I didn't need to use the backups but is was nice to know they were there. I felt entering the various passwords for all my installed apps was a much better deal than adding the international area code to the 166 contacts I have in my address book.
    Good luck. And thanks for the post.

  • HP Laserjet 4 not showing up in chooser

    I acquired a HP Laserjet 4 with a jet direct card installed. The printer does not show up in the chooser. The printer test page shows that AppleTalk is active and the printer should be named Laserjet 4 but I cannot see it when I click on the Laserwriter 8 icon in the chooser.
    Appletalk is active and the computer is using the printer port (appletalk control panel)
    The printer and computer are connected by an DIN 8 cable (old stylewriter cable).
    I really like to get this printer working with my Beige G3 any suggestions?

    I think I solved my own problem. I do not have the postscript SIM module installed in the printer. That is probably why the printer is not showing up in the choosen. Postscript may have to be installed in the printer first.

  • Server: Mail configuration of Server Admin not showing ANY Accounts

    I have an LDAP directory for my accounts and in the Server Admin GUI, under the Mail configuration, I am not showing any accounts. Currently mail services not working and I have tried to reconstruct the db to no avail.
    I the POP log im gettting ...
    Aug 10 14:03:29 mail pop3[24233]: DBERROR: critical database situation
    In the Mail Access log ...
    Aug 10 14:04:56 mail lmtpunix[29548]: DBERROR: critical database situation

    How about more info?
    Did you ever have a working setup? Accounts?
    How did you try to reconstruct?
    Check /var/log/mailaccess.log and post some more info for a process number (number in square brackets)

  • Account name not showing in 'Partners' Block for sold to party and ship to

    Hi Experts,
    I created a return order by confirming the Account.
    Under 'Partners' Sold-to-party, ship-to-party, activity partner showing the account name but when i clicked on any of these links it is not showing the BP name.
    Please suggest why it is not showing the BP name inside the sold-to-party,ship-to-party, activity partner.
    Thanks in Advance,
    Kishore

    Hi Experts,
    I created a return order by confirming the Account.
    Under 'Partners' Sold-to-party, ship-to-party, activity partner showing the account name but when i clicked on any of these links it is not showing the BP name.
    Please suggest why it is not showing the BP name inside the sold-to-party,ship-to-party, activity partner.
    Thanks in Advance,
    Kishore

  • Chapter name not showing up in Scene Selection

    I have an iMovie 9 project that has three chapters.   I've used the Chapter Markers to delineate where they begin and what their names are.
    I've sent the finished project to Media Browser and then I go to iDVD to burn the project successfully and all seems well. 
    The trouble is, the first chapter's name is not showing up in the Scene Selection.   It's just listed as "The Beginning" instead of the name I've given it.  I checked it in the preview function before I burn the DVD, and it's not there, either.  The other two chapters' names show up successfully. 
    Can anyone help me here?  Thanks. 

    I just made sure that the Chapter Marker was at the very beginning of the clip, and that seemed to have solved the problem.

  • Contact names not showing in messages, only number

    nokia 6121  no names will show when ringing or recieving texts so I dont know who they are from etc, very frustrating, how do I change it to show the contact name not number? I cant find any settings to help me? thanks

    Hi, In such case, try to check the things below:
    1> Make sure all contacts are stored in unique memory : sim or phone memory (recommend phone memory)
    2> Try to avoid 1 contacts has few numbers and other case, similar or same names for fews contacts
    3> Add your country code into the normal number format, eg: 0123455678 --> saved as +60 12345678 (+60 is the country code for MY)
    4> Check the settings under Contacts folder: Contacts > Settings > Contact view or Display contacts > try to change Last name/ First name view option one by one

Maybe you are looking for