Server Time Machine vs Client Time Machine

I have been running Time Machine on my iMac since I got it. I installed server and now I notice that the server app has Time Machine as well but its turned off. My oringinal Time Machine in system preferences seems to be running like it always has. What is the difference between the two?
Thanks, Steve

Server can provide Time Machine services to clients, much like a Time Capsule does. Unlike a Time Capsule, you can easily swap out the drive used to provide those backup services.

Similar Messages

How do I make Lion Server support more than one Time Machine disk?

Under Snow Leopard Server, I had two disks set up for Time Machine backups. This came about as I'm running a Mac Mini with the 500 GB internal drives which turned out to be insufficient for one of the connected Macs which uses a terabyte drive. I then added an external 6 TB drive and made it a Time Machine destination too. Worked beautifully. When I upgraded to Lion Server the external large drive was no longer available for backups and the interface for configuration within Server only allows for one drive to be in use at a time. Any suggestions (short on reverting to Snow Leopard) as to how to re-enable having both drives available for networked Time Machine access?
Thanks!

Hi Adam,
Before I even realised that the Server app had a setting for TM, I just configured TM backups on my (SL) clients as I had done in SL.
I shared the drive(s) on the server I wanted to use.
For each client, I mounted the appropriate shared drive containing its sparseimage file, then set TM on the client to use that drive.
Then I unmounted the shared drive and started TM.
It mounted the remote drive (without displaying it in Finder) and opened the sparseimage, showing the "Time Machine Backups" volume on the desktop.
So you could use any drive attached to the server to backup any client.
It worked fine for me.
In the end, I changed my clients to use the (single) shared "Backups" volume which Server.app creates because I can fit all my stuff on one drive.
HTH

Time of the client machine

Hi,
Thanks for reading my post in advance.
I am working on this code to read the time on the client machine which could be locations outside the USA also.
Is there a way I can code so that I can get what the time running on the client machine.
I did some research on the internet and a found a code which gives some ideas about the date format on the client machine.
Is there a way we can modify this code so we can see the time client running on the client's machine.
<%
// get client locale
java.util.Locale locale = request.getLocale();
// get Dateformat for client's locale
java.text.DateFormat dateFormat =
     java.text.DateFormat.getDateTimeInstance(
          java.text.DateFormat.LONG,
          java.text.DateFormat.LONG, locale);
%>
<%=dateFormat.format( new java.util.Date() ) %>

You have mentioned in your post that you are trying to find out the time on the Client Machine. It does not clarify if code running on server itself is acting as client or it is the code running on the browser.
If it is the browser then the code that you have posted may not be of any help as Java does not run on the browser(except in applet). You will have to use the Date class of JavaScript. If you make an instance of this class in JavaScript with default constructor it will be initialized by the time of the machine where the browser is running.
If you want to have the time of the server where your jsp code is converted into html, you can use the GregorianCalendar class. The default constructor initialize itself with the date and time of the machine on which the application/web server is running. You can use the methods of this class to retrieve the different parameters of date and time.
HTH.

Time on the client machine

Hi,
Thanks for reading my post in advance.
I am working on this code to read the time on the client machine which could be locations outside the USA also.
Is there a way I can code so that I can get what the time running on the client machine.
I did some research on the internet and a found a code which gives some ideas about the date format on the client machine.
Is there a way we can modify this code so we can see the time client running on the client's machine.
<%
// get client locale
java.util.Locale locale = request.getLocale();
// get Dateformat for client's locale
java.text.DateFormat dateFormat =
java.text.DateFormat.getDateTimeInstance(
java.text.DateFormat.LONG,
java.text.DateFormat.LONG, locale);
%>
<%=dateFormat.format( new java.util.Date() ) %>

Is there a way we can modify this code so we can see the time client running on the client's machine.Use JavaScript.

Ow can I use my time capsule as a time machine backup without using it wirelessly and not as a wireless router?

How can I use my time capsule as a time machine backup without using it wirelessly and not as a wireless router?

bzb888 wrote:
I have a wireless transmitter already, would like to use the capsule just as a back up drive, I tried hooking up from the ethernet port on the imac to the one of the ports on the capsule but then my Wifi would not work. do I hook the cable to the port with the circle or the arrows?
It is better to have the TC as part of the main network in bridge. You do not need to run wireless.
If you want to use the TC plugged in by ethernet and still use wireless for internet, that is possible but the setup is rather more complicated.. the computer must not get confused about which device to use as a gateway or dns server.
See info in this thread on setting this up.
https://discussions.apple.com/thread/4817218?tstart=30
I need to add.. a USB drive would be cheaper, faster and more reliable. It is really poor use of a TC.

Problem: Socket connection is not creating in machine, through utility program (MFC Dll), on ListDisplay service port - 3334 (on separate machine), while we are able to telnet on same ListDisplay service port - 3334 from same issue machine on same time

Problem: Socket
connection is not creating in machine, through utility program (MFC Dll), on ListDisplay service port - 3334 (on separate machine), while we are able to telnet on same ListDisplay service port - 3334 from same issue machine on same time
Environment: -
OS:
Windows XP SP2/7
Code:
VC 6.0
Dll: MFC
Problem Description: -
We have written a utility program which create socket (Using windows standard method [MFC]), and then make connection with another service (List Display) running
on port 3334 in different machine and retrieve the required list data. This program was working fine in almost all the machines.
But, we have received a severe intermittent issue on two machines. Client is facing issue in displaying the list data from port 3334.
Attempt: -
First we tried to debug code, and we come to know that socket is not creating in utility program. So we tried to telnet on ListDisplay service port 3334 and we were surprised that we were able to telnet, then we opened some more
telnet window on same port 3334 around (6 to 8) window, and each cmd connected properly. But we were not able to create socket from utility program.
Problem is severe because issue is intermittent.
We have tried all the way, but we are not able to figure it out, that what can be the exact problem and what are the conditions, when utility program will not
connect with ListDisplay service on port 3334.
Kindly assist to resolve this issue. For any help, we would be really thankful.

Hi,
According to your description, it seems that you have created an utility program which is making connection with another service port 3334, however, two clients are facing issue in display the data list from port 3334.
Port: 3334/TCP
3334/TCP - Known port assignments (1 record found)
Service
Details
Source
directv-web
Direct TV Webcasting
IANA
Since the port 3334 is used by directv-web service, I'd like to suggest check this service it is working well on the problematic clients.
1. The client can be resolved in DNS well? Please run "nslookup" in the prompt command.
2. Is there any 3rd party application interrupting? Do test in clean boot.
2. Strongly suggest you run process monitor tool to analysis it.
I am looking forward to your reply if you have any updated on your side.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Time Machine cannot find Time Capsule after turning auto backups off

2010 macbook 7,1 OSX 10.6.8. Brand new rev.4 Time Capsule 2TB (MD032LL/A) just bought yesterday.
Everything set up just fine and wireless is working. Backups are working.
Issue is that as soon as I turn the Time Machine slider to Off (I can turn it back to On at this point, doesn't matter once it's been in the Off position) in TIme Machine preferences, then try and Enter Time Machine or do a backup, it cannot find the Time Capsule (says cannot find backup volume or such). I have to reselect the drive even though it's icon is showing right on the preferences screen. A reboot will enable it to find the Time Capsule without my input.
If I leave Time Machine turned on, the backups run fine and I can enter the Time Machine. It is turning off Time Machine that triggers the issue.
Tried the following:
-Rebooted Time Capsule
-Made sure Time Capsule name is less than 27 characters (it is 19)
-Firewall is off
-Filevaullt is off
-Booted into Safe Mode
-Repaired permissions
-Trashed TIme Machine plist
-Updated OSX
At this point I called Applecare and they had me send them a capture of my TIme Machine data and will get back to me Monday.
Oddly, my 10.5.8 iMac G5 2ghz is working fine with Time Machine and does not have this issue. I can turn Time Machine off and on all I want and it can find the Time Capsule with no problem.
Thanks for any help.

Apple is still working on the issue but I have now noticed that I cannot VNC into my work PC anymore. I get a "Could not connect to server, connection refused:5900"
I am using Chicken of the VNC and it worked fine until I got the Time Capsule. I know that 5900 is the port used for something and this sounds like it is related to the Time Capsule.
I can't help but think this is also related to the "Cannot find backup disk" message from Time Machine. This all sounds like the Time Capsule goofed up the works here.
Also, I now have tons of reports in the console of it not being able to count items in a file at system/library/StartupItems. That folder is NOT there. Which is why I assume the errors. I have seen a few other reports and people are just restoring the file from Time Machine or making it via command line with admin. When I go back far enough in Time Machine, the file IS there but has nothing in it.
I asked Apple about that too and they checked a 10.6.8 computer and it had the file so not sure what is up there. Not sure if it was 10.6.8 update or the bunch of iTunes, etc that I did after that.
Have not restored that file yet, will wait to see what they say about the Time Capsule mess.
Any ideas on restoring my VNC connection?

Can CS3.3 & CS4 Master play nice installed on same machine at same time?

First off here are the specs on my desktop and laptop:
Desktop:
Mac Pro running OSX 10.5.6 - 2 x 3 GHz Dual-Core - 6 GB RAM - CS3.3 Master Collection currently installed
Laptop:
MacBook Pro running OSX 10.5.6 - 2.4 GHZ Intel Core 2 Duo - 2 GB RAM - CS3.3 Master Collection currently installed
I recently received all the install discs for CS4. Spent the last hour researching how CS3 and CS4 play together when installed on same machine at same time. I haven't found anything that addresses my questions, thus the post.
At present, not enough of my work colleagues have CS4, so if I install CS4 and uninstall CS3 - and need to pass a file on to someone who doesn't have CS4, they can't open it in CS3.
Also, I use AfterEffects with many 3rd party plugins. Until I can verify that CS4 plays nice with these plugins, I can't afford to uninstall AfterEffects CS3. Obviously, I need to keep CS3 up and running on my desktop and laptop.
But now that I have CS4 ready to install, I of course want to start using it and learning the new features.
Has anyone successfully been able to install CS4 Master apps on a machine similar to either my desktop or laptop specs and have CS3.3 Master apps continue to work properly?
I trust Adobe takes these types of version overlaps seriously and plans for them since people want to try out or start using the newest version but ensure there is a sufficient overlap period before uninstalling the older versions.
Thanks for your comments
jslicer

j,
Your old apps will work. But the new versions will be the defaults. You can touch your files to the old application to launch it or launch the old application first, and then open files "normally".
If you need to ensure compatibility with older versions on other machines, don't delete the old apps. Or be prepared to save back to the old version before handing off the files. Note that InDesign cannot save back more than one version and in general, any features used that are new to the new apps will not be recognized when those files are saved back.
Neil

Using TIME MACHINE with a TIME CAPSULE

There's often a bit of confusion about this terminology: +*Time Machine+* vs. +*Time Capsule:+*
_*Time Machine*_ is Apple software that performs backups, to an external HD, a Time Capsule, etc.; and also allows you to browse and restore from them. It comes with Leopard and Snow Leopard, but cannot run on any previous versions of OSX.
A _*Time Capsule*_ is a piece of Apple hardware that combines a wireless router and hard drive, that can be used for Time Machine backups and/or other data.
Most Time Machine questions & problems are not unique to Time Capsules. For those, or if you don't find what you need here, try one of these:
Time Machine - Frequently Asked Questions
Time Machine - Troubleshooting
They can also be found in the *User Contributed Tips* section of both +Time Machine+ forums:
Mac OS X v10.5 Leopard > Time Machine
Mac OS X v10.6 Snow Leopard > Time Machine
Contents
|
QUESTIONS
*Q1. How do I set up Time Machine to back up to my Time Capsule?*
*Q2. How do I set up Time Machine to back up to a USB drive connected to my Time Capsule?*
*Q3. Can I use my Time Capsule for Time Machine backups AND other data?*
*Q4. My Time Capsule is too small to back-up my Mac(s). Now what?*
*Q5. Should I delete backups? If so, how?*
*Q6. How do I back-up my Time Capsule and/or USB drive(s) connected to it?*
If you don't see your question here, try the Frequently Asked Questions *User Tip,* also at the top of the +Time Machine+ forum.
|
PROBLEMS
*P1. The Backup disk image could not be created.*
*P2. Time Machine could not complete the backup . . sparsebundle could not be accessed. (Error 109).*
If you don't see your problem here, try the Time Machine - Troubleshooting *User Tip,* also at the top of the +Time Machine+ forum.
QUESTIONS
|
_*Q1. How do I set up Time Machine to back up to my Time Capsule?*_
|
First, set up your Time Capsule via +Airport Utility.+ Keep the name you assign to it, your Computer, and your network short (under 25 characters), and avoid embedded spaces, special characters, and punctuation (see item #P1 below for details). Make sure your Mac can connect via an Ethernet cable, if at all possible, as well as wirelessly.
The setup and first backup (of your entire system) will be much faster if you connect via Ethernet.
|
a. If the +Time Machine+ icon isn't already in your Dock, drag it there from your Applications folder. See below for more about it's use.
b. Right-click it and select +Open Time Machine Preferences,+ click the +Show Time Machine status in the menu bar+ box (see below), then click +Select Disk+ (on Leopard, this button will be either +Choose Backup Disk+ or +Change Disk).+
c. A list of possible destinations will appear. It should include your Time Capsule (with the name you gave it via Airport Utility), and may show other internal or external drives as well. Select your Time Capsule and click the +Use for Backup+ button.
d. A prompt for your name and password will appear. In some cases there won't be a Name field, but if there is, enter your short user name. Also enter the password you set up for the Time Capsule via Airport Utility, then click the Connect button.
e. A 120-second countdown to the start of your first backup will appear in the +Next Backup+ area of the TM Preference panel.
|
Note that this first backup will copy the entire contents of your system, except for a few things that are skipped automatically, such as system work files, most caches, your logs, trash, etc., and anything else you may have excluded (see #10 and #11 in the Frequently Asked Questions *User Tip,* also at the top of the +Time Machine+ forum). So it will be rather lengthy, depending on how much data is on your system, whether you're connected via Ethernet or WIFI, and if WIFI, how good the signal is.
You can continue to use your Mac while TM is backing-up, and you can even cancel a backup if necessary, but to make this first full backup as fast as possible, try not to overload your Mac or cancel the backup.
|
_*The Time Machine Icons in your Menubar and/or Dock*_
|
In the steps above, you dragged the TM Application's icon into your Dock, and clicked the +Show Time Machine status in the menu bar+ box.
For detailed info about them, see question #24 in the Frequently Asked Questions *User Tip,* also at the top of the +Time Machine+ forum.
+Go to Top+
_*Q2. How do I set up Time Machine to back up to a USB drive connected to my Time Capsule?*_
|
Mostly the way you set it up to use the Time Capsule's internal HD.
But first, attach the drive directly to your Mac, and erase and format it per the instructions in #5 of the Frequently Asked Questions *User Tip,* also at the top of the +Time Machine+ forum. Note, however, that it doesn't matter whether you use the +Mac OS Extended (Journaled)+ or +Mac OS Extended (Case-sensitive, journaled)+ Format, since Time Machine will put your backups in a sparse bundle that's case-sensitive. You cannot change that.
Unlike the Time Capsule's disk, you can partition the USB drive. That's highly recommended if you're going to be putting other data there, so the backups don't completely fill the disk (but be aware that Time Machine cannot back that "other" data up. See question #Q6 below).
If you're backing-up multiple Macs to the same drive, you can make one partition for each, but it's not as helpful on a network drive, because each Mac's backups will be in a separate sparse bundle. So you can let them share the disk or a partition.
Also note that if you've been doing backups to an external disk connected directly to your Mac, you cannot continue the same set of backups when you connect it to your Time Capsule. They are stored differently, and Time Machine will put them in a sparse bundle, alongside but *completely separate from* the backups made locally, and the first backup will be a full backup of your entire system.
Once the USB disk is set up the way you want it, use the setup procedure in question #Q1 above, but in step (c), select the USB drive/partition, not the Time Capsule's internal HD.
*RAID Sets connected to a Time Capsule:*
|
Time Machine will back up to a +Hardware Mirrored RAID set,+ also called +RAID 1,+ (sold that way, with multiple drives in the same enclosure). However, if you partition the +Hardware Mirrored RAID set,+ once you start using it with TIme Machine, you cannot change the sizes later and continue to back up to the same set of backups.
While you can connect multiple USB drives to a Time Capsule via a USB hub (a powered one is best), Time Machine +*will not+* back up to a +software Mirrored RAID+ set (where you combine the drives into a single volume via Disk Utility).
+Go to Top+
_*Q3. Can I use my Time Capsule for Time Machine backups and other data?*_
|
You can put other data on your Time Capsule's internal HD, but there are three major considerations:
Especially for things like photos and videos, access may be too slow for convenient viewing, and worse for editing. So test this a bit before you decide what to put there.
Time Machine cannot back-up that other data, so you'll need some other method. See question #Q6 below.
Time Machine will, by design, fill up all the space available to it, so there may be a conflict between the sparse bundle it puts your backups in, and the other data. There is a workaround, to "reserve" some space there, by creating a disk image of the desired size and storing your data there, but it's a bit cumbersome, and two Macs can't share it at the same time.
An alternative is to connect a USB drive to your Time Capsule. Then you can back up to the TC's disk and use the USB drive for other data, or vice-versa. But note that Time Machine cannot back-up the USB drive while it's connected to the TC (see question #Q6 below).
If you want to reserve space on the TC's internal disk, here's how:
|
a. Start the +Disk Utility+ app (in your Applications/Utilities folder). Click the +New Image+ icon in the toolbar (or select +File > New > Blank Disk Image+ from the menubar). If the little arrow to the right of the "Save As" box points down, click it so it points up.
b. Give it a name in the "Save as" box. This name will appear on the TC's disk, with ".dmg" appended. (Similar to the way the sparse bundle containing your Time Machine backups appears, with ".sparsebundle" appended).
c. Click your TC in the sidebar. It may take a few moments for Disk Utility to recognize it, and show it in the center pane.
d. In that center pane, select the blue Share folder for your +Time Capsule+ (you may need to scroll down, or enlarge the window, to see it). Once selected, you'll see any existing disk images in the right pane.
e. Give the Image a name. This name will appear on your desktop and/or Finder sidebar when you mount the .dmg by double-clicking it, if you have the +External Disks+ box checked in +Finder > Preferences > General+ or +Finder > Preferences > Sidebar.+
f. Select the Size for the amount of space you want to reserve, either one of the pre-sets or Custom which allows any size. Avoid taking all the remaining space for the disk image, as Time Machine needs a bit of room to operate. Also note that if very little space is left, it will begin deleting old backups very soon, to make room for new ones.
g. Select the desired Format, probably the default of +Mac OS Extended (Journaled).+
h. If you want it encrypted, select the desired type.
i. Select single partition, either GUID or +Apple Partition Map.+
j. Select +Read/Write disk image+ for Image Format.
k. Click the Create button. The larger the image size, the longer this will take.
|
When complete, the new disk image will be automatically mounted on your Mac's desktop, ready to receive the files you want to move into it. (When you first open a disk image, there may not be a sidebar and/or toolbar; if so, select +View > Show Toolbar+ from the Finder menubar.)
To access this disk image from another computer, you must first eject it from this one, since only one can mount it at a time. Otherwise, the other one will see a message that the disk image is "Temporarily unavailable."
Note that you may be able to change the size of the disk image later, via +Images > Resize+ from the Disk Utility menubar (while the disk image is not mounted or selected in Disk Utility's sidebar).
+Go to Top+
_*Q4. My Time Capsule is too small to back-up my Mac(s). Now what?*_
|
You can attach a USB drive to your Time Capsule. Then you can back up to the USB drive instead of the Time Capsule's internal HD. If you have multiple Macs, you can back some up to the TC's internal drive, and others to the USB drive.
If you need even more space, you can connect multiple USB drives via a hub (a powered one is usually best), and back up different Macs to each. What you cannot do, however, is have one Mac's backups continue from the Time Capsule's internal HD to a USB drive connected to it, or have the backups for any one Mac "span" two drives.
The exception is, you can connect two (or more) drives that are in a +concatenated RAID+ set (sometimes called +RAID 0).+ In that configuration, all the drives in the set are treated as a single volume (see +Concatenated RAID+ in the Help for Disk Utility for details). This configuration may cause some other difficulties; once they're in a RAID set, you cannot connect any drive to your Mac separately -- it's all or none. And if one drive fails, you risk losing everything on all the drives in the set.
See question #Q2 above for setup instructions for backing-up to the USB drive.
+Go to Top+
_*Q5. Should I delete backups? If so, how?*_
|
It depends on exactly what you want to do, and why.
Under normal circumstances, you shouldn't have to delete anything. TM automatically "thins" (deletes) backups every time it does a new backup, on the following schedule:
"Hourly" backups after 24 hours (except the first of the day, which is a "Daily" backup).
"Daily" backups after a month (except the first of each week, which is a "Weekly" backup.)
"Weekly" backups are kept until TM needs the space for new backups; then one or more of the oldest weeklies will be deleted.
However, TM will never delete the backup copy of anything that was on the disk being backed-up at the time of any remaining backup. So all that's actually deleted are copies of items whose originals were changed or deleted before the next remaining backup.
But if you do need to delete backups, here's how:
To delete individual backups, or all backups of selected item(s), see #12 in the Frequently Asked Questions *User Tip,* also at the top of the +Time Machine+ forum.
To delete everything on the Time Capsule's internal HD, use +*Airport Utility.+* Select +*Base Station > Manual Set-Up+* from the Menubar, then Disks in the tool Bar, then Erase.
To delete everything on a connected USB drive/partition, you can delete via the Finder, but that may take a very long time. It may be faster to disconnect it from your Time Capsule, connect it directly to your Mac, and use Disk Utility (in your Applications/Utilities folder) to erase the disk/partition.
To delete all the backups for one Mac, without disturbing anything else on the Time Capsule's internal disk, open the TC via the Finder and delete the sparse bundle associated with that Mac.
To delete all the backups for one Mac, without disturbing anything else on a connected USB drive, either open the USB drive via the Finder and delete the sparse bundle associated with that Mac, or disconnect the drive from the TC, connect it directly to your Mac, and delete the sparse bundle from there.
+Go to Top+
_*Q6. How do I back-up my Time Capsule and/or attached USB drive(s)?*_
|
That depends to some extent on what you want to back up, and where it is.
It's generally not a good idea to try to back-up your Time Machine backups. If there's a problem with them, it will be copied to (and perhaps magnified on) the copy.
A better solution is probably to use either Time Machine or a different application to make separate, independent backups of your Mac, to a different destination. A portable external hard drive is great for this; you can periodically connect it to your Mac, make a backup, then take it to a secure off-site location, so you're protected against fire, flood, theft, direct lightning strike on your power lines, etc. If you use Time Machine for this, you'll have to use the disk selection process each time you want to switch, via +Time Machine Preferences.+
Many folks use the CarbonCopyCloner or SuperDuper! apps to make "bootable clones" of their internal HD to an external HD. While these usually don't have "archived" copies of previous versions of things you've changed or deleted, you can boot and run your Mac from them if your internal HD fails. Your Mac may run a bit slower, but it will be usable. Both are easily found via Google.
Since Time Machine cannot back up your Time Capsule's internal hard drive, or a USB drive connected to it, if you have other data there, you'll need a different method to back up that other data.
In a pinch, you can disconnect a USB drive from your Time Capsule, attach it to your Mac, and copy or back it up that way.
|
There is a procedure that will let you "archive" the TC's internal disk to a USB drive connected to it.
But it's not quick, since since the data must be read from the TC's internal disk to your Mac, then sent *back through the Time Capsule* to the connected USB drive. And it's "all or nothing" -- you can only use this procedure to copy the entire contents.
All users will be disconnected from both the internal HD and the connected USB disk (but the network will remain usable).
Attach a USB drive with at least as much free space as the total amount of data on the TC's internal HD (see #5 in the Frequently Asked Questions *User Tip,* also at the top of the +Time Machine+ forum, for formatting instructions).
Turn Time Machine "Off" via +Time Machine Preferences.+ Stop all processes that may be accessing the Time Capsule's disk. If possible, connect your Mac to the Time Capsule with an Ethernet cable -- it will still be slow, but faster than WIFI.
Then follow this Apple procedure: Using AirPort Utility 5.3.1 or later to make a copy of the Time Capsule disk.
+Go to Top+
PROBLEMS
|
_*P1. The Backup disk image could not be created.*_
|
Oddly enough, Time Machine can be rather picky about the way certain things are named.
Check your +*Computer Name*+ at the top of the System Preferences > Sharing panel.
It must not be blank; it should not be more than 25 characters long; and you should avoid punctuation, spaces, and special characters.
After changing it, click the Edit button and make the corresponding change to the +*Local Hostname.+*
If that doesn't help, apply the same rules to the name of your Time Capsule and Network, via +Airport Utility.+
+Go to Top+
_*P2. Time Machine could not complete the backup .. sparsebundle could not be accessed. (Error 109).*_
|
The sparsebundle containing your backups is corrupted.
Try Repairing it, per #A5 in the Time Machine - Troubleshooting *User Tip,* also at the top of the +Time Machine+ forum.
If the sparsebundle is on your Time Capsule's internal HD, and Disk Utility can't fix it, your only option is to delete it (or erase the TC's disk), and let Time Machine start over. You may be able to prevent this from happening again by changing the names per problem #P1 above.
If the sparsebundle is on a USB drive connected to your Time Capsule, and Disk Utility can't fix it, it's possible a heavy-duty 3rd-party +Disk Repair+ application, such as +Disk Warrior+ can. (You'll have to connect the drive directly to your Mac.) These are not cheap, and there's no guarantee they can fix it. Be certain whatever you use is compatible with your OS. For Disk Warrior, you need at least version 4.1.1 for Leopard, 4.2 for Snow Leopard.
+Go to Top+

This tip is ready for consideration.
It is an update to the current Tip at: http://discussions.apple.com/thread.jspa?threadID=2296894
Changes:
Q1: replaced info about the TM icons with a link to the TM FAQ tip.
Q2: added info about RAID sets attached to a TC
Q6: reworded a bit and replaced last paragraph with a link to the Apple article.

ASA 5505 as a SSL VPN Server and Easy VPN Client at the same time?

Is it possible to configure and operate the ASA 5505 as a SSL VPN server and Easy VPN Client at the same time? We would like to configure a few of these without having to purchase additional ASA 5505 and use a 2 device method (1 SSL VPN Server and 1 Easy VPN Client). Thanks in advance.

I don't think it is possible. Following links may help you
http://www.cisco.com/en/US/products/ps6120/products_configuration_guide_chapter09186a008068dabe.html
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008071c428.shtml

How can I see the old backups of my previous Macbook done by Time machine in a Time capsule with my new iMac?

How can I see the old backups of my previous Macbook done by Time machine in a Time capsule with my new iMac? I've changed from a Macbook to a iMac because that one stopped working and I cannot use it anymore. I've been able to import all the data of the last backup of the Macbook when setting the new iMac, but I cannot access now to the old backups of the Macbook and there are information that wasn't in the last backup and I would like to recover. Thank you very much.

Yes, you can ..
Read Q17 here.
http://pondini.org/TM/FAQ.html
Strongly recommend his whole section.. 14-17 and read it carefully to understand the ways you can make TM work for you.

Can i access my old macbook pro's 'Time machine' saved on time capsule with a new laptop

How can i access my old macbook pro's 'Time machine' saved on time capsule with a new laptop.
Also why can i only EITHER have the capsule attched to the internet OR have it as my backup external hard drive?? Things are not running smoothly can someone please help?
Many thanks,
Cirsflan

Answered in your other thread.. keep to one. Just confusing running two threads with the same question.
https://discussions.apple.com/thread/4863146?tstart=0

I am trying to update my time machine backup on time capsule, but time machine keeps trying to create an entirely new backup (evidenced by the 200GB backup size). How can I get time machine to modify my old backup rather than create a new one?

I am trying to update my time machine backup on time capsule, but time machine keeps trying to create an entirely new backup (evidenced by the 200GB backup size). How can I get time machine to modify my old backup rather than create a new one?

It must have found the old backup corrupt.. so you will more than likely have little choice. You can archive off the old backup if it is still useful.
You can also verify it. See A5 http://pondini.org/TM/Troubleshooting.html
He also has some info on this problem. eg C13.

Can I use my time capsule as a time machine and a hard drive

Hi all,
Can I use my time capsule as a time machine and a hard drive?
I don't want to store much on my imac, I would like to store it on the time capsule.
If this is possible, how do I do it?
Thanks, Crankyhead.

This is often asked.. and we always have the same answer. have you thought this through?
https://discussions.apple.com/thread/4830944?tstart=0

HT201514 i can't see the time capsule from airport utilities. i did follow "From the Apple menu, choose System Preferences. Choose View Time Machine. Set Time Machine to On if it is off. .....but i couldn't find the time capsule from airport utility.....

i did follow "From the Apple menu, choose System Preferences. Choose View > Time Machine. Set Time Machine to On if it is off "
. .....but i couldn't find the time capsule from airport utility..... why?

Are you using a new 802.11ac Time Capsule - the "tall" one - and are you still using Mac OS X 10.6.8?
You need OS X 10.7.5 "Lion" or later, or an iOS device, to configure an 802.11ac Time Capsule:
http://manuals.info.apple.com/MANUALS/1000/MA1645/en_US/airport_time_capsule_802 11ac_setup.pdf
See page 12.

Server Time Machine vs Client Time Machine

Similar Messages

Maybe you are looking for