Server with same Profile cannot access same networking

Hi,
I have a lab running 1 x Nexus 5010, 2 x FIC 6120'XP's, UCS 5108 and 2 x B200 M2 Blades. I have configured everything per flexpod guidelines (except I have only 1 Nexus). I boot from SAN over Fibre and zoning everything is working 100% My firmware is 2.1(1f)
Question:
Assinged to each blade is 2 vNICs connected to FabricA and FabricB (FabricA = port-channel from FICA to Nexus and FabricB = port-channel from FICB to Nexus - Nexus has 2 different port-channels conf for each link to each FIC)
After I install VMware, I tag vlan 10 (management vlan) for the management traffic of each VMware node. The funny thing is when I ping server 2, iget a response but not from server 1. Both are configured using the same service profile. If I ping server 1 from server 2, I get a response. This leads me to believe that for some reason the traffic is not leaving the FIC from server 1, but it is when using server 2. I have attached screenshots of both servers vifpaths.
Can someone please help urgently as this is driving me crazy as I do not know what the hell is going on.
Cheers

Hello
Hope this solution will help.
Just found my notes on deleting the users profile:
"Deleted Profile logs back in with temporary profile.
This problem occurs if the current user's profile was accidentally deleted from the system.
Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry
1. Log on to the system by using an administrative user account other than the user account that is experiencing the problem.
2. Back up all data in the current user's profile folder if the profile folder still exists, and then delete the profile folder. By default, the profile resides in the following location:
%SystemDrive%\Users\UserName
3. Click Start, type regedit in the Start Search box, and then press ENTER.
If you are prompted for an administrator password or for confirmation, type your password, or click Continue.
4.Locate the following registry subkey:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList
5.Under the ProfileList subkey, delete the subkey that is named SID.bak.
Note SID is a placeholder for the security identifier (SID) of the user account that is experiencing the problem. The SID.bak subkey should contain a ProfileImagePath registry entry that points to the original profile folder of the user account that is experiencing the problem.
6. Exit Registry Editor.
7. Log off the system.
8. Log on to the system again."
& for more information kindly check the below link too :- http://community.spiceworks.com/topic/187995-network-pc-cannot-access-1-specific-server .
Regards
keshav

Similar Messages

When i login with microsoft account cannot access with administrative share c$

i have a problem when i login to windows with microsoft account cannot access any network computer with administrative sharing c$,d$ with windows 8.1
but when i login with local account can access
and some people tell me create key in regedit t fix it
after enter user name and password show this error
and i apply your instruction and not fix until now
note:
my Machine windows 8.1 if another machine in network windows 7 can access a hidden share if machine in network windows 8.1 show this message in image 2
but if i login with local user can i access all machine hidden share network windows 7 and 8.1

yes this computer i want to access name poland2-work and have two users
first :administrator
second : poland 2

How to update a table (CUSTOMER) on a Report Server with the data from the same table (CUSTOMER) from another server Transaction server?

I had an interview question that is:
How to update a table (Customer) on a server ex: Report Server with the data from the same table (Customer) From another server ex: Transaction server?
Set up steps so inset, update or delete operation takes place across the servers.
It would be great if someone please enlighten me in details about this process in MS SQL Server 2008 R2.
Also please describe would it be different for SQL Server 2012?
If so, then what are the steps?

I had an interview question that is:
How to update a table (Customer) on a server ex: Report Server with the data from the same table (Customer) from another server ex: Transaction server?
Set up steps so that inset, update or delete operation gets done correctly across servers.
I was not sure about the answer, it would be great if someone please put some light on this and explain in details about this process in MS SQL Server 2008 R2.
Also it would be very helpful if you please describe would it be different for SQL Server 2012? If so, then what are the steps?

Integrating WebSphere Portal Server with Sun Java System Access Manager

Hi All,
Is it possible to Integrate WebSphere Portal Server with Sun java System Access Manager?. If so plz send me any doc or web site link for the same.
Thanks in Advance
Rgds,
Lessly J

Rushi-Reliance wrote:
Kindly let us know how to proceed further as we are waiiting some reply from your team.As I already advised in your previous posting (http://forums.sun.com/thread.jspa?threadID=5359095), you are best off re-installing solaris from scratch and installing Communication Suite 6 update 1 if you cannot get Access Manager 7.1 configured.
Regards
Shane.

[network access] User cannot access through network

Hi!
I'm facing a strange problem now.
One of the users of my WD Personal Cloud cannot access through network share. When he tries to login the same fails and the login is prompted again. This happens in Windows but happens also in Linux.
When the same user tries to login in the mobile cloud app or in the browser (only in windows because after all this years the browser cloud funcionality still not works for Linux users, a shame...) it works as it should be.Also i tried to create a new users and happens the same, in the app or browser works great in network share simply refuse to login! I already rebooted, turn off, disconnected and did other things but nothing worked.
There are 9 users and 10 share in he cloud and the firmware version is v04.01.04-422. The diagnosis is OK!
Thanks for the help. Best Regards.

Hi again! There is no error. When i enter the share ask for the login credentials, i insert user and password and when i click ok simply ask the credentials again, and again, and again... It's the same compotment as if the credentials are wrong but they are not, i use them for online login in wd2go.com or mobile app and they work.And another thing is that if i create a new user happens the same, i can login in mobile app and wd2go.com but in the windows share (or samba share if in Linux) it fails without any error, simply ask for the credentials again and again and again... The old users works fine. The comportment is same with IP or name. Thanks for the help, Best Regards.

I have recently unlocked my iPhone 4. I got the comforation saying it was unlocked. For some reason I cannot access my network settings? Any suggestions. I am trying to use the phone on Net 10 network.

I recently unlocked my iphone 4. I am trying to use it on Net 10's network. However, i cannot access the network settings. I have the Net10 Sim already in it. A few notes listed below of what i have tried:
1.) I downloaded the iphone configuation utility. But cannot get the right settings to apply. (so if you have the correct ones i could use those)
2.) i have watched 1000 youtube videos and been on practically every page online and tried 1000 different versions of APN settings through the configuration
3.) I do not have another SIM card from another carrier to try.
Open to suggestions on how i can get the APN settings to change. Not worried about picture messaging or anything, but would like my internet to work. Calls and text work fine.

i have seen this option..problem being...i dont have access to WIFI i live in the middle of ten buck too! We cant even get internet out here i have to go a friend house to get internet. I was going to try that once i did get to town but was looking for other options here at home frist.

I have ios7 on my iphfone 4 I now have a iphone5 with ios8 I cannot access the cloud to download my contacts and apps. the error is both phones need to be ios8, my iphone4 will not allow changing to ios8. can anyone help. Thanks

i have ios7 on my iphone 4 I now have a iphone5 with ios8 I cannot access the cloud to download my contacts and apps. the error is both phones need to be ios8, my iphone4 will not allow changing to ios8. can anyone help. Thanks

Contact Apple and speak to someone in account security.

Replaced network device with same ip - cannot access ssh/http

Hello-
I replaced a network equalizer and used the same ip.
<www> - <firewall> -<netequalizer>-<cisco core>-<lan>
I can see this online and we are passing traffic. Yet cannot access ssh or http. I have been troubleshooting with netequalizer but figure i come here. I am thinking this may be an arp issue on the cisco core? Any thoughts?
thanks

While it might be possible that it is an arp issue on the core I think it is not so likely. Can the core ping the netequalizer? If the core can ping then it almost certainly is not an issue with arp.
My guess is that there was something in the configuration of the previous netequalizer then enables management by SSH and HTTP that was not done in the configuration of the replacement.
HTH
Rick

I have macbook pro w existing iPhoto library. Now have Canon printer and loaded Canon software for same. Cannot access iPhoto library from Canon software, but prints fine from iPhoto. How can I use iPhoto library w Canon software?

I have a macbook pro w exisitng iPhoto library. I now have Canon printer and loaded Canon software for same. I cannot access iPhoto library for use from Canon software. I can print from iPhoto directly to new printer without problem. How can I use iPhoto library with Canon software? I would like to try the software to see which I prefer...

Simply export some photos from iPhoto to a folder on the desktop and experiment.
Without telling us even what this program is, not to mind what it does, that's the best anyone can suggest.
Regards
TD

How do I share my pictures with another profile on the same computer

I would like to share my photo library with another profile user on the same computer

For iPhoto 09 (version 8.0.2) and later:
What you mean by 'share'.
If you want the other user to be able to see the pics, but not add to, change or alter your library, then enable Sharing in your iPhoto (Preferences -> Sharing), leave iPhoto running and use Fast User Switching to open the other account. In that account, enable 'Look For Shared Libraries'. Your Library will appear in the other source pane.
Any user can drag a pic from the Shared Library to their own in the iPhoto Window.
Remember iPhoto must be running in both accounts for this to work.
If you want the other user to have the same access to the library as you: to be able to add, edit, organise, keyword etc.
Quit iPhoto in both accounts. Move the Library to the Users / Shared Folder
(You can also use an external HD set to ignore permissions, a Disk Image or even partition your Hard Disk.)
In each account in turn: Double click on the Library to open it. (You may be asked to repair the Library Permissions.) From that point on, this will be the default library location. Both accounts will have full access to the library, in fact, both accounts will 'own' it.
However, there is a catch with this system and it is a significant one. iPhoto is not a multi-user app., it does not have the code to negotiate two users simultaneously writing to the database, and trying will cause db corruption. So only one user at a time, and back up, back up back up.

Cisco ASA 5505 L2TP VPN cannot access internal network

Hi,
I'm trying to configure Cisco L2TP VPN to my office. After successful connection I cannot access to internal network.
Can you jhelp me to find out the issue?
I have Cisco ASA:
inside network - 192.168.1.0
VPN network - 192.168.168.0
I have router 192.168.1.2 and I cannot ping or get access to this router.
Here is my config:
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 198.X.X.A 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network net-all
subnet 0.0.0.0 0.0.0.0
object network vpn_local
subnet 192.168.168.0 255.255.255.0
object network inside_nw
subnet 192.168.1.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool sales_addresses 192.168.168.1-192.168.168.254
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic net-all interface
nat (inside,outside) source static inside_nw inside_nw destination static vpn_local vpn_local
nat (outside,inside) source static vpn_local vpn_local destination static inside_nw inside_nw route-lookup
object network vpn_local
nat (outside,outside) dynamic interface
object network inside_nw
nat (inside,outside) dynamic interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 198.X.X.B 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication enable console LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set my-transform-set-ikev1 esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set my-transform-set-ikev1 mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set my-transform-set-ikev1
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh timeout 30
console timeout 0
management-access inside
dhcpd address 192.168.1.5-192.168.1.132 inside
dhcpd dns 75.75.75.75 76.76.76.76 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy sales_policy internal
group-policy sales_policy attributes
dns-server value 75.75.75.75 76.76.76.76
vpn-tunnel-protocol l2tp-ipsec
username ----------
username ----------
tunnel-group DefaultRAGroup general-attributes
address-pool sales_addresses
default-group-policy sales_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:5d1fc9409c87ecdc1e06f06980de6c13
: end
Thanks for your help.

You have to test it with "real" traffic to 192.168.1.2 and if you use ping, you have to add icmp-inspection:
policy-map global_policy
class inspection_default
inspect icmp
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Server 2012 Local Shares - Cannot access using \\IP but works via \\localhost

I've been stuck on this problem for the last couple of days and I can't find a solution on the internet that works.
I have a Windows Server 2012 instance running on Amazon AWS with a public IP address. I am using it as an SCCM (System Center 2012 Configuration Manager) Server (so it is a Domain Controller also). I realize that it's probably not best practice to use a public
IP here, but I'm in a weird position where we are not connecting any of the Clients to the actual Domain (they are Workgroup computers all around the world). The goal here is to use SCCM to deploy software packages to all of the Clients, which are not on the
same LAN/VPN/Domain.
This is my first time setting something up like this, so I followed this guide. I am able to get the Workgroup computers to show up in the SCCM Server Device list (via manual client install), but these Workgroup computers need access to the Server's shares
to download the software packages. On Amazon, I opened all ports and allowed all IPs to communicate with the Server. I am able to RDP into the Server from any Workgroup computer using the IP address, but cannot access the Server's SMB shares even though I
am attempting the connection with a Domain account with access to those shares.
I decided to see if I can even connect to the shares locally on the Server. Logging in with an account with administrator privileges, I can access \\localhost\shares without
a problem. But when I try to do \\X.X.X.X\shares,
it asks for user/pass (confirming that it is able to connect) and I put in the correct credentials for the account with administrator privileges (using DOMAIN\ACCOUNT), but it continually says that the user/pass is incorrect. After I click cancel, an error
comes up saying "Error Code 0x80004005 Unspecified Error".
It is crazy to me that the administrator account that is logged in cannot access the local shares via the public IP address... obviously no remote computer would be able to access the shares if the Server itself cannot. I have tried disabling the firewall,
but this makes no difference. I am able to ping the IP from the Server and I get a response.
I have searched around the internet for a solution but nothing has worked. Here are some of the suggestions I've found (that have failed):
- Making sure "Client for Microsoft Networks" and "File and Printer Sharing for Microsoft Networks is installed and enabled for the Ethernet Adapter
- Enabling NetBIOS over TCP/IP in IPv4 properties
- Ensuring IPv6 is disabled
- Server, TCP/IP NetBIOS Helper, and Workstation (services) are all running
Any ideas? Sorry for such a long post, just wanted to get as many details as I could. All help is appreciated. Thanks!
Shawn

Hi,
Are there any anti-virus software or other third party products running on the server? If yes, please disable them to see if it resolves the issue.
Here is a similar thread below I suggest you refer to:
Shared Folder Access
http://social.technet.microsoft.com/Forums/windowsserver/en-US/c0bbbe8e-55d8-467c-bb85-2b98f122cc15/shared-folder-access?forum=winserverPN
Best Regards,
Amy

Cannot access internal network after Tiger upgrade

I've just upgraded an eMac (1.25GHz, 768MB) from 10.3.9 to 10.4.6. Although I can get online, access Mail and all applications, I cannot access the internal network at all.
I've updated to 10.4.9, but still no luck. I've restarted, logged in as a different user, logged out and in again, removed the 'com.apple.networkconfig.plist' file from the 'Library/Preferences' folder, but still doesn't work.
I can see all the aliases to the other machines on the network in the sidebar, but clicking on them brings up a message "The alias xxxx could not be opened, because the original alias could not be found.".
Other machines can see this on on the network. File Sharing is turned on.
Any thoughts, I'm tearing my hair out a bit!
Powerbook G4 Mac OS X (10.4.8)

no good, is an afpmounter error, i solved it with an
Archive and Install
http://docs.info.apple.com/article.html?artnum=107120-en
maybe someone have a solution..
i think is an error during the update (i had the same from panther to tiger)
with A&I and half-hour, your machine work perfectly.

Vpn client can access internet but cannot access internal network

I am using PIX 501 to setup a VPN. At first the VPN client cannot access the internet once they logged in via the Cisco system vpn client, so i enable split tunneling. Now the VPN client can access the internet but they can't access the internal network.Due to the limited characters can be posted here, only necessary IOS coding is posted on the next message. Who knows how to solve this problem? Pls Help.....

enable password ********** encrypted
passwd ********** encrypted
hostname Firewall
domain-name aqswdefrgt.com.sg
access-list 100 permit ip 192.168.1.0 255.255.255.0 192.168.50.0 255.255.255.0
access-list nat permit tcp any host 65.165.123.142 eq smtp
access-list nat permit tcp any host 65.165.123.142 eq pop3
access-list nat permit tcp any host 65.165.123.143 eq smtp
access-list nat permit tcp any host 65.165.123.143 eq pop3
access-list nat permit tcp any host 65.165.123.143 eq www
access-list nat permit tcp any host 65.165.123.152 eq smtp
access-list nat permit tcp any host 65.165.123.152 eq pop3
access-list nat permit tcp any host 65.165.123.152 eq www
access-list nat permit tcp any host 65.165.123.143 eq https
access-list nat permit icmp any any
ip address outside 65.165.123.4 255.255.255.240
ip address inside 192.168.1.2 255.255.255.0
ip verify reverse-path interface outside
ip local pool clientpool 192.168.50.1-192.168.50.50
global (outside) 1 interface
nat (inside) 0 access-list 100
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) tcp 65.165.123.142 smtp 192.168.1.56 smtp netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.142 pop3 192.168.1.56 pop3 netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.143 smtp 192.168.1.55 smtp netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.143 pop3 192.168.1.55 pop3 netmask 255.255.2
55.255 0 0
static (inside,outside) tcp 65.165.123.143 www 192.168.1.55 www netmask 255.255.255
.255 0 0
static (inside,outside) tcp 65.165.123.152 smtp 192.168.1.76 smtp netmask 255.255.
255.255 0 0
static (inside,outside) tcp 65.165.123.152 pop3 192.168.1.76 pop3 netmask 255.255.
255.255 0 0
static (inside,outside) tcp 65.165.123.152 www 192.168.1.76 www netmask 255.255.25
5.255 0 0
static (inside,outside) tcp 65.165.123.143 https 192.168.1.55 https netmask 255.255
.255.255 0 0
access-group nat in interface outside
route outside 0.0.0.0 0.0.0.0 65.165.123.1 1
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
aaa-server plexus protocol radius
aaa-server plexus (inside) host 192.168.1.55 ******** timeout 5
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set myset esp-des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map cisco 1 set transform-set myset
crypto map dyn-map 20 ipsec-isakmp dynamic cisco
crypto map dyn-map client authentication plexus
crypto map dyn-map interface outside
isakmp enable outside
isakmp key ******** address 0.0.0.0 netmask 0.0.0.0
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
isakmp policy 40 authentication pre-share
isakmp policy 40 encryption 3des
isakmp policy 40 hash md5
isakmp policy 40 group 2
isakmp policy 40 lifetime 86400
vpngroup vpn3000 address-pool clientpool
vpngroup vpn3000 dns-server 192.168.1.55
vpngroup vpn3000 wins-server 192.168.1.55
vpngroup vpn3000 default-domain aqswdefrgt.com.sg
vpngroup vpn3000 idle-time 1800
vpngroup vpn3000 password ********
telnet 192.168.1.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
terminal width 80

IPad informs me that "Safari could not open the page because the server stopped responding" I cannot access emails or interneton Ipad.

Ipad message "Safari could not open the page because the server stopped responding". I cannot access emails or internet.

Thankyou for suggestion. My PC was working ok ( accessing emails/internet) which puzzled me. It's usually the PC that drives me nuts and the iPad that is great.I discovered my TV was having difficulty with a connection to broadband. I turned off the main Wifi router and switched it on again and all seems to be well. My IPad was suggesting, however, that all was well with the Wifi connection. It had a tick against it in Settings. Very strange!
Byron

Server with same Profile cannot access same networking

Similar Messages

Maybe you are looking for