"Service battery" msg after installing ram

Hello, I have some trouble with my macbook (6.1 with OSsl 10.6.8).
I installed some RAM yesterday (up to 4GB from 2GB, 2x 2GB SODIMMS) and everything was OK.
I wake up this morning and opened the lid (I didn't shut down last night) and macbook is "dead", like the battery is drained, but the led in front side was lit.
Anyway I connected the power and tried to start the system. Nothing, I closed the lid and opened it again and it started, once I went in OS I realized that the battery is at 57% so it doesn't make sense on why it shutted down...
Also it says at the battery icon "service battery" now, even if it seems to function normaly and the cocconut battery is not reporting anything unusal.
When I installed the new RAM I unplugged the battery from the main board to avoid any static electricity damage, I installed the RAM and then just plugged back the battery.
I followed a picture by picture guide from ifix it (just in case it helps) and didn't touched anything else, or at least I think so.
I reopened and unplugged/plugged the battery on the board again but nothing changed.
Any idea on what I possible did wrong or umplugged by accident?
Thanks in advance.

Sorry for the double post, but I can't find any edit button.
I noticed that the behavior from this morning is coming back again when I close the lid for more than a few minutes.
When I open the lid the monitor is not open and after I press the power button for a few moments to close and press it again it is like recovering the last session from a battery drain fall asleep.

Similar Messages

  • What do I need to do AFTER installing RAM

    OK
    I just upgraded two G5 dual processor machines in my dept.
    Went from 2.5G to 4G in one and 1G to 4G in the other.
    I really have not noticed any sizeable improvement in speed.
    System profiler says "OK" on memory. They are all matched, same brand etc...
    MAC HELP did not have any tips about installing RAM.
    My question is; must I do anything AFTER installing RAM such as reset PRAM, permissions etc...

    No. There is nothing more you need to do.
    Going from 2.5 to 4 will probably not make that much difference, unless you are using high-end apps like Final Cut Pro that use a lot of RAM, or you run many apps at the same time.
    I definitely noticed a big difference going from 0.5 to 1.5. I only noticed a small difference going from 1.5 to 2.5.

  • HT6114 i have a problem with notification of service battery since i installed mavericks. My macbook air is 2012 version.

    i have a problem with notification of service battery since i installed mavericks. My macbook air is 2012 version. Any solution?

    This from the crash log
    Dyld Error Message:
      Library not loaded: /System/Library/Frameworks/Accounts.framework/Versions/A/Accounts
      Referenced from: /System/Library/StagedFrameworks/Safari/Safari.framework/Safari
    indicates there is a missing library on your system. What problems were you having before that caused you to delete Safari? How did you delete it?
    You're best bet in this case is to re-install the OS. While doing a re-install will not normally harm your user data having a good working backup in cases like this is essential.

  • What is going on the my battery life, after installing Mavericks, what a drain!!!

    What is going on the my battery life, after installing Mavericks, what a drain!!!

    You can try resetting the SMC and NVRAM.
    http://support.apple.com/kb/ht1379
    http://support.apple.com/kb/ht3964
    You can also try running the short and/or extended Apple hardware test by holding D button while booting up and then following the instructions.
    http://support.apple.com/kb/ht1509
    If that doesn't work (seems not extremely likely that it will) you can backup and try reinstalling a fresh OS.
    If that still doesn't work maybe the battery is bad.  If you don't feel like messing with all that just take it to Apple.  They should have a test they can perform.

  • Battery drain after installing IOS7 on Iphone 4

    Hi
    I have recently installed IOS7 on my IPhone 4.
    The battery drains really quickly even when I am not doing anything with the phone. I never had these problem before updating.
    Suggestions please???
    Thanks

    I have also noticed what appears to be decreased battery life after the upgrade, though not this bad.  Seems many people are noticing problems. 
    I noticed and changed a couple of settings that seem to have helped.
    - first, fully shut off the phone and then turn it back on - i read online this helped some, immediately after the update.
    - in mail settings, for the icloud account (I dont use this but it was configured by default) check the sync settings . it defaults to push, which takes more power.  you might want to disable push and set to fetch for this and any other accounts you have, for additional power savings
    - in settings, location services, scroll to the bottom and tap system services : All of them are defaulted to on.  I turned off location-based iads and setting time zone since i dont need those. (I also opted out of the diagnostics and usage as part of the setup, but it was set to on in this screen - i left it on for the time)
    - also in settings -- location settings:  check the list of apps and verify that only the ones you want, are enabled
    These few settings seem to have improved things

  • Late 2013 macbook pro showing Service Battery warning after 1 year and 2 months

    Hey there,
    I purchased a 13" MacBook pro retina late 2013 in December
    The battery has recently started showing the "service battery" warning. Here is a screenshot from Coconut Battery:
    Surely after only about a year the battery should not be holding only 70% of the charge. Is this level of wear unusual? If I were to take this to an apple store would Apple likely replace it even though it is out of warranty?
    Cheers guys.

    unfortunately, the batteries warranty is only one year.  The only options were the ones they gave you: buy a new battery (which I recommend), or use your mac on the power supply only without the battery.

  • 'Service Battery' status after upgrade to 10.9.2

    After I upgraded my MBA mid 2012 to OSX 10.9.2....I keep seeing the battery status show up as 'Service Battery' very regularly....most of it shows up and a few times, it shows regular 'Battery' status.
    The charge cycles for the battery is currently at just 367...and I believe Apple promises atleast 1000 charge cycles
    What is going wrong here ?
    Is this a software bug or is it really my MBA's battery that is going down ?
    Help appreciated.
    Regards,
    Chandan

    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
    If this does not help, contact Apple.
    Best.

  • Service battery message after only 147 cycles

    I have a 2010 Macbook Pro with Mavericks on it.
    After only 147 cyles I am getting a message that says "Service Battery"
    Why would this be happening?
    I did some searching and see it might be a common problem? Is Apple going to fix this?
    Doesn't make sense after that many cycles to need to replace the battery....

    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
    If this does not help, contact Apple.
    Best.

  • Exchange replication service not starting after installing Rollup update 3 v3

    Hi,
    I have installed rollup update 3 v3 for exchange 2010 sp1 on my mailbox server. This mailbox server is a DAG member. After installing update rollup, Microsoft exchange replication service on this server attempts to start & show status started for couple
    of seconds & then gets stopped. This behaviuor continues untill i uninstall this rollup. I have installed the same rollup on other DAG member as well with no problem. The following errors are generated in the application logs,
    Event ID 4096: The Microsoft Exchange Replication service failed to start the Tcp Listener. Please review the Event Log for more information. The system will attempt to start the service again in 30 seconds.
    Event ID 2121: The Microsoft Exchange Replication service failed to start the TCP listener. Error: System.Net.Sockets.SocketException: Only one usage of each socket address (protocol/network address/port) is normally permitted
    at System.Net.Sockets.Socket.DoBind(EndPoint endPointSnapshot, SocketAddress socketAddress)
    at System.Net.Sockets.Socket.Bind(EndPoint localEP)
    at Microsoft.Exchange.Cluster.Replay.TcpListener.StartListening()
    Event ID 4999:
    Watson report about to be sent for process id: 6000, with parameters: E12, c-RTL-AMD64, 14.01.0289.001, msexchangerepl, M.E.Cluster.Replay, M.E.C.R.ReplicaInstance.TargetGetCopyStatus, System.MethodAccessException, a379, 14.01.0289.001.
    ErrorReportingEnabled: True
    Event ID 2060: The Microsoft Exchange Replication service encountered a transient error while attempting to start a replication instance for DB1\SRV-MBX2. The copy will be set to failed. Error:
    The NetworkManager has not yet been initialized. Check the event logs to determine the cause.
    Event ID 2060:
    The Microsoft Exchange Replication service encountered a transient error while attempting to start a replication instance for DB2\SRV-MBX2. The copy will be set to failed. Error: The NetworkManager has not yet been initialized.
    Check the event logs to determine the cause.
    Thanks
    in Advance!!

    I hope you are following the best practice to install rollup on DAG. 
    Suspend activation for the databases on the server being updated.
    Perform a server switchover so that all databases on the server are passive copies. There will be a brief interruption in service for the mailboxes hosted on the active databases during the switchover process.
    Install the update rollup.
    Resume activation for the databases on the updated server.
    Perform database switchovers as needed.
    http://blogs.technet.com/b/scottschnoll/archive/2009/12/10/installing-update-rollup-1-for-exchange-2010-on-dag-members.aspx
    Thanks Uday Kiran,
    Senior Consultant
    Cyquent Technology Consultants, Dubai
    Please Mark as answer if it helps you

  • HT1519 Mid 2009 MBP 15" cycle count 500ish but getting "Service Battery" notification after Mavericks upgrade

    Dear Apple,
    I've got a Mid 2009 Macbook pro 15". Been going great. Love it. Much better user experience than my PC laptop.
    However, straight after Mavericks upgrade, I've been starting receiving "Service Battery" notification. I've had a look at my Cycle count, which is 516 as it currently stands. According to the spec, this expected battery count is 1000. Any help would be greatly appreciated.
    Cheers,
    Dan

    Dear Apple,
    I've got a Mid 2009 Macbook pro 15". Been going great. Love it. Much better user experience than my PC laptop.
    However, straight after Mavericks upgrade, I've been starting receiving "Service Battery" notification. I've had a look at my Cycle count, which is 516 as it currently stands. According to the spec, this expected battery count is 1000. Any help would be greatly appreciated.
    Cheers,
    Dan

  • Battery life after installing iOS 4.0 on 3GS

    I've read a little about loss of battery life on the 3GS after installing 4.0 so I was curious who else is experiencing these problems. Since installing the new software my phone is losing about 8-10% per hour when sitting idle. I am losing a full charge and using the phone less than 30 min. I have done a restore and have made sure aps are closed. I can;t get the phone to stop eating battery life. Any suggestions?? Please!

    Bingo.....decided to try a restore factory settings through ITunes and then backed up with the phone settings so I did not lose all my stuff, if this had not worked I would have tried again but then reset as a new phone and start afresh, but thankfully I did not need to. Note you still end up with OS 4.0
    After going through the set up and then recharging just once, the battery has performed pretty much as it is has done since initial purchase. In 16 hrs of minimal usage and in standby it has used 30%.
    Good luck.
    Cheers
    Metalfox

  • Service battery error after upgrading to Mavericks

    Immediately after upgrading to Mavericks my Mid 2009 MacBook Pro that was purchased in September of 2013 received a service battery error.  The laptop will continue to charge while plugged in, but loses battery power at an alarming rate when unplugged.  Has Apple addressed this problem yet, and when can we expect a solution or repair for this?

    Battery Cycle Count
    Battery Life - Mavericks

  • MacBook sleep light remains on after installing ram

    After installing 2x2G of RAM into my MacBook 4,1 the sleep indicator light remains on and the display in blank. My MacBook then properly booted after installing the old RAM. Any suggestions?

    Try one new RAM stick with one old RAM stick. If it starts up then you've got RAM that was made with PCs in mind. PC are less picky than Macs about the speed of their RAM so 667mhz RAM is often overclocked to 675mhz and runs at variable speed to make it compatable with more PCs. PCs have the hardware to run the RAM at the speed that works best for them. MacBooks require RAM that only runs at 667mhz. By putting one good stick in it forces the other one to run at the correct speed.
    These are good online stores for Mac RAM
    Crucial Memory http://www.crucial.com/
    OWC http://eshop.macsales.com/shop/memory/MacBook/DDR2/
    Data Memory Systems http://www.datamemorysystems.com/apple-memory.asp

  • FYI: TrendMicro antivirus prevents Transport Service from starting after installing Echange Server 2013 Service Pack 1

    I installed Exchange Server 2013 SP1 in my test environment. After that mail flow between internal and external mail servers completely stopped. In the end I discovered that Transport Service on both of the mailbox servers refused to start (or, to be more
    exact, stopped shortly after starting).
    The following events appeared in the System event log:
    Event ID 1052 (error)
    Source: MSExchange Extensibility
    Message: Failed to create agent factory for the agent 'ScanMail SMTP Receive Agent' with error 'Failed to create type 'TrendMicro.SMEX.hookE12TransportAgent.hookE12SmtpReceiveAgentFactory' from assembly 'C:\Program Files\Trend Micro\Smex\hookE12TransportAgent.dll'
    due to error 'type not found'.'. Please verify the corresponding transport agent assembly and dependencies with correct version are installed.
    Event ID 16023 (error)
    Source: MSExchangeTransport
    Message: Microsoft Exchange couldn't start transport agents. The Microsoft Exchange Transport service will be stopped. Exception details: Failed to create type 'TrendMicro.SMEX.hookE12TransportAgent.hookE12SmtpReceiveAgentFactory' from assembly 'C:\Program
    Files\Trend Micro\Smex\hookE12TransportAgent.dll' due to error 'type not found'. : Microsoft.Exchange.Data.ExchangeConfigurationException: Failed to create type 'TrendMicro.SMEX.hookE12TransportAgent.hookE12SmtpReceiveAgentFactory' from assembly 'C:\Program
    Files\Trend Micro\Smex\hookE12TransportAgent.dll' due to error 'type not found'.
       at Microsoft.Exchange.Data.Transport.Internal.MExRuntime.FactoryTable.CreateAgentFactory(AgentInfo agentInfo)
       at Microsoft.Exchange.Data.Transport.Internal.MExRuntime.FactoryTable..ctor(IEnumerable agents, FactoryInitializer factoryInitializer)
       at Microsoft.Exchange.Data.Transport.Internal.MExRuntime.RuntimeSettings..ctor(MExConfiguration config, String agentGroup, FactoryInitializer factoryInitializer)
       at Microsoft.Exchange.Data.Transport.Internal.MExRuntime.MExRuntime.Initialize(String configFile, String agentGroup, ProcessTransportRole processTransportRole, String installPath, FactoryInitializer factoryInitializer)
       at Microsoft.Exchange.Transport.Extensibility.AgentComponent.Load()
    Event ID 701 (informational)
    Source: MSExchangeTransport
    Message: The service will be stopped. Reason: Microsoft.Exchange.Transport.TransportComponentLoadFailedException: Loading of component 'SmtpReceiveAgents' failed. ---> Microsoft.Exchange.Transport.TransportComponentLoadFailedException: The agent component
    failed to load. ---> Microsoft.Exchange.Data.ExchangeConfigurationException: Failed to create type 'TrendMicro.SMEX.hookE12TransportAgent.hookE12SmtpReceiveAgentFactory' from assembly 'C:\Program Files\Trend Micro\Smex\hookE12TransportAgent.dll' due to
    error 'type not found'.
       at Microsoft.Exchange.Data.Transport.Internal.MExRuntime.FactoryTable.CreateAgentFactory(AgentInfo agentInfo)
       at Microsoft.Exchange.Data.Transport.Internal.MExRuntime.FactoryTable..ctor(IEnumerable agents, FactoryInitializer factoryInitializer)
       at Microsoft.Exchange.Data.Transport.Internal.MExRuntime.RuntimeSettings..ctor(MExConfiguration config, String agentGroup, FactoryInitializer factoryInitializer)
       at Microsoft.Exchange.Data.Transport.Internal.MExRuntime.MExRuntime.Initialize(String configFile, String agentGroup, ProcessTransportRole processTransportRole, String installPath, FactoryInitializer factoryInitializer)
       at Microsoft.Exchange.Transport.Extensibility.AgentComponent.Load()
       --- End of inner exception stack trace ---
       at Microsoft.Exchange.Transport.Extensibility.AgentComponent.Load()
       at Microsoft.Exchange.Data.Directory.ADNotificationAdapter.RunADOperation(ADOperation adOperation, Int32 retryCount)
       at Microsoft.Exchange.Data.Directory.ADNotificationAdapter.TryRunADOperation(ADOperation adOperation, Int32 retryCount)
       at Microsoft.Exchange.Transport.SequentialTransportComponent.Load()
       --- End of inner exception stack trace ---
       at Microsoft.Exchange.Transport.SequentialTransportComponent.Load()
       at Microsoft.Exchange.Transport.Components.Activate()
    The reason for that behavior was TrendMicro ScanMail for Exchange 11. Seems that it was unable to work with the new SP properly and prevented the entire Transport Service from starting. Uninstallation of the antivirus eliminated the issue.

    Actually, you can just disable the agents until TrendMicro releases a patch and then enable them again:
    http://community.trendmicro.com/...
    BTW, a similar problem (high CPU utilization and services not starting) is hitting the AVG package:
    http://forums.avg.com/..
    Step by Step Screencasts and Video Tutorials

  • Mac Three Beeps after install RAM. Again.

    Greetings
    Introduction
    I've seen all discussions on the topic and still decided to create new one in order to collect information.
    I've joined the club. Now I also have Macbook Pro, which freezes and beeps three times from time to time.
    I often attend to pubic lectures, or give a presentation myself, so this beeping issue is not acceptable for me.
    Description
    Problems began when upgraded my RAM to 16GB (two Corsair CMSO8GX3M1A1333C9 modules).
    After random period of time (10 minutes - 3 days) my MacBook Pro freezes and beeps three times until I do hard shutdown.
    I checked my new RAM (each module separately) with memtest.
    One of modules was bad and I changed it from merchant.
    Replaced it. Still beeping
    Checked both modules with memetest again (10 runs, each module separately). No errors. Still beeping
    Performed PRAM reset. Still beeping
    Performed SMC reset. Still beeping
    Disabled SMS. Everything was fine for 3 days and moment I began feeling happy it beeped.
    Ran memtest on both modules simultaneously. Got kernel panic ("kernel trap at ...")
    I suspect that problem is not in memory itself (since both modules passed quite intensive tests) but that something brakes when I put two of them together...
    Maybe Mac is not able to process them in right way or something...
    Summary
    Mac: MacBookPro Early 2011
    RAM: 16GB, 2 x Corsair CMSO8GX3M1A1333C9
    Status: Periodic beeping and freezing
    Didn't help: Switching memory slots, Replacing faulty module, Disabling SMS (Sudden Motion Sensor), Resetting PRAM, Resetting SMC
    Helped: nothing yet
    Main question
    Is there any way I can diagnose everything and pinpoint source of the problem?
    Since nobody can answer that, I suggest we try empirical approach and just figure out which RAM models work fine.
    Conclusion
    I would like to collect success and failure stories:
    You upgraded RAM and you have same problem and nothing helps
    You upgraded RAM, had this problem and something helped
    You upgraded RAM and everything is fine
    Please leave your comments in following format
    Mac: your Mac model
    RAM: memory type and model
    Status: Still beeps / Fixed / Everything was fine from beginning
    Didn't help: List of step you did to fix the problem and failed
    Helped: Steps which lead you to fixing the problem
    Let's collect enough of such data and we might me able to see the pattern and come up with idea how to avoid The Problem.
    - Ilya

    With the link you provided for the Corsair RAM you purchased.
    The one you provided in your link is a PC notebook/laptop RAM - see image of your link below:
    The one you need for your Macbook Pro has a different part number - see image below:
    Best to return and exchange it for the right one so you won't have any issues for your Macbook Pro.
    Or you can install Crucial 16GB (i have this in my 2011 13 Inch Macbook Pro) or 16GB Patriot Mac Series (I have this in my 2011 15 Inch Macbook Pro).
    Good luck - hope you get it sorted out.

Maybe you are looking for