Set B Channel ID information to Preferred in MGCP Gateway

Hi All,
We recently had some E1 PRI issues and our Service Provider has asked us to set B Channel ID information to Preferred.
We are using a MGCP Gateway with CUCM 9.1.2
When we enable ISDN debug we could see the Channel ID as Exclusive.
Jul 25 13:02:07.566: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0043
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98381
                Exclusive, Channel 1
I tried to change it to Preferred by configuring the command, "isdn negotiate-bchan" under the serial interface but still debug shows it as Exclusive only.
Let me know whether we can change the B Channel information either in CUCM or MGCP Gateway.

Hi
Can you try the below:-
1- interface x/x/x:15
isdn protocol-emulate network
isdn bchan-number-order ascending
then test again
2-Go to CUCM - gateway and do the below
CHANNEL IE TYPE " TIMESLOTS "
Thanks
please rate all useful information

Similar Messages

HT3702 When setting up my account information, and clicks done something in a red box pops up saying "Please contact itunes support to complete this transaction" What do i do about this ?

When setting up my account information, and clicks done something in a red box pops up saying "Please contact itunes support to complete this transaction" What do i do about this ?

You can contact iTunes support here (these are user-to-user forums, ) : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page

Mib for reading/setting RF channel on standalone Access Points

Hei Everybody. Does anybody know if there is a SNMP mib sfor reading/setting RF channel and other RF-parameters on 1131AG standalone Accesspoints. In my network we are using the "least congested frequency" choice for Channel selection and wants to se what the result for this is.
Regards, Roy

"Least Congested Frequency" does not work.... either set your AP's to a specific channel or only highlight channels 1, 6, or 11. You can use a mib browser to seethe mib listing... this link migh help... son't know if its different from the 1131AG:
http://www.oidview.com/mibs/9/CISCO-DOT11-IF-MIB.html

I have firefox set to delete personal information (log in to websites) when I close it ... However firefox isntead doesn't delete anything, keeps the cookies, and when I reopen firefox I'm still logged in (to websites like facebook). What do?

Pretty much this: I have firefox set to delete personal information (log in to websites) when I close it ... However firefox instead doesn't delete anything, keeps the cookies, and when I reopen firefox I'm still logged in (to websites like facebook). What do?
Privacy settings aren't working even though they're all appropriately checked off.
I think Firefox is saving cookies??

Let all cookies expire when you close Firefox.
* Tools > Options > Privacy > Cookies: "Keep until": "I close Firefox"
Make an Allow exception for the ones that you want to keep.
* Tools > Options > Privacy > Cookies: "Exceptions"
You can inspect and modify the permissions for the domain in the current tab in "Tools > Page Info > Permissions"
Make sure that you do not use "Clear Recent History" to clear the "Cookies" and the "Site Preferences" (Site Preferences includes the cookie exceptions)
* https://support.mozilla.com/kb/Clear+Recent+History
Clearing cookies will remove all specified (selected) cookies including cookies that have an allow exception.
See also:
* https://support.mozilla.com/kb/Cookies
* https://support.mozilla.com/kb/Enabling+and+disabling+cookies

Setting midi channel for ES2 in logic express 9

i have a track selected with an ES2 patch
I can play from my midi keyboard, sounds good and I can see the midi coming in from my midi channel
problem is it's not the midi channel i selected in logic for the track
it appears everything with logic is in omni mode
i can play one of my keyboards in channel 3 and the other keyboard in channel 5 and both trigger in logic channel set to midi channel 7
please, any suggestions?

Unfortunately it did not work. I am playing in midi channel 6, and it shows properly on the midi in/out panel near the bottom of the screen by the numerator and cpu meter. Shows the midi notes coming in just fine
I have my software synth track selected as midi channel 3, and it plays this track....while my controller is in channel 6
I can also set iLogic Express to play an external midi track to any midi channel and it will still play no matter what channel my incoming midi channel is set to (1 - 16)
Midi is getting into Logic Express just fine
So why will it not only play in the midi channel I have selected for the track?
I also want to use an additional midi keyboard (or usb) to play a different track and midi channel, but they all play as if in omni mode regardless of the channel set from the transmitting keyboard and the information showing on the midi in/out panel
I am using an old Motu 8x8 midi interface into an M-Audio Firewire Audiophile which has one single midi in and out (no midi thru) to the mac.
Works like a charm except in Logic Express
Thanks for your help - I'm truly lost..... and I did read the manual cover to cover to try and find the answer
Thanks

How to set alpha channel names in a format plugin?

I am writing a format plugin with 6 color planes for CMYK mode. I want to set the apha channel names for planes 5 and 6 to "White" and "Clear" instead of "Alpha 1" and "Alpha 2" when I read the color data from my file. How do I set the alpha channel names?
Thanks!

I am still trying to find a solution to this. The propChannelName is read only and the documentInfo structure is NULL when reading. Any suggestions?

Tabs are not saved on closing. Settings may be set incorrectly gives no information

Not asked to save tabs on closing. tried safe mode and checking for corrupt files as in the instructions. Under "Settings may be set incorrectly" no information is given.

You can use "Firefox > History > Restore Previous Session" to get back the previous session.
There is also a "Restore Previous Session" button on the default about:home Home page.

Setting DAQ channel by property node does not display the value

I am writing a configuration VI to set channel selection and calibration parameters for an SCXI chassis. I store a default setup in a configuration (ini) file and read that file automatically when the VI is called. The value from the file are set by property nodes using the "Value" property. The values from the file do not display in the DAQ channel selection rings, but the numerical calibration values do display correctly. When I click the down arrow in the channel rings, the correct value displays.
This behavior exists both in LabView and app-builder EXEs. Also, if I change the property nodes for the DAQ channels to local variables, it works. The Value (signaling) property doesn't cause them to display
properly either. Why can't I use the property node?

I don't understand exactly what you are trying to do.
Please upload a simple VI to demonstrate the behavior you are describing. Remember also to attach the .ini file.
Best regards,
Philip C.
Applications Engineer
National Instruments
www.ni.com/ask
- Philip Courtois, Thinkbot Solutions

How to set printer option for information broad casting

Hi
I have web template theer i select information broad casting and selected by print , theer its aksing printer name? how can i give setting , if i wnat get prinetr where can i do printer setting
ple let em know

Hi,
we can set in sap menu>tools>CCMS-->Print:
for more details check this:
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/1029340b-041d-2a10-76bd-fe83350aad29
thnks.

Setting the Field Capture Information

I am having interframe flicker in my timecode and keyframe burn in after I perform reverse telecine with Cinema Tools. I was told my my lab that I shouldn't worry about this, that it is normal. However I read in the CT manual that you should not have any blurring or flicker and that all burn-in should be clearly legible after performing reverse telecine.
Depending on the settings I use in the field capture information, I get slightly better results in the image area using one setting over another, though I can't eliminate the interlace/blur/flicker over the burned-in codes. I determined that my telecine was done with "One field, with field 2 dominance" by looking at the chart on page 128 in the CT manual, and then setting the reverse telecine settings to "Field 2 only" as recommended there. ALthough this setting seems to be correct, this makes the interlacing/blur/flicker in my image worse. My lab told me to use a different setting: Field 1 Field 2 (even though this setting doesn't seem to be the correct one according the chart in the CT manual), and this gives me no interlacing in my image, though it is still there in in the burn-in.
Does anyone know what I'm doing wrong?

Hi,
Currently too the said field is optional in the settings for Field Selection in MIGO- Check with transaction code OMJX, although the field entry is grayed out, the standard functionality is that the entry made in "Qty in unit of entry" gets copied to this field.
Regards
Merwyn

Export using Compressor for DTV setting (7 channel audio)

I am trying to export a FCP project using Compressor - I have 8 channels of audio - to make up L, R, C, FLE, Ls, Rs,Lt, Rt. I am exporting ProRes 422 HQ with the SMTP DTV Audio setting. At the end of the export, I have been dragging the file into soundtrack to check the audio output, and there is only info on the first two channels of the 8-channel audio track.
The sequence settings are set as discrete channels. What am I missing?

And then, you feel like an eejit when you realize that you forgot to assign the channels in the timeline....

Channel Lineup for HD Preferred XF Triple Play

I recently upgraded to HD Preferred XF Triple Play. Where can I find a Comcast channel lineup?

it is on the webiste at http://www.xfinity.com/customers/clu/channellineup.ashx or http://www.xfinity.com/Channel%20Lineup/Channel%20Lineup%20Print%20View.html

Recently purchased iPad Mini. Could not get it to connect. Changed router's setting to Channel 6 and IPad connected. Even after 6.0.2 it will not connect to some home networks although it will to public networks e.g. McDonald's.

Recently purchased iPad Mini. Downloaded iOS 6.0.1. Could not get it to connect to Home WiFi using Linksys G Router. Have another Wifi Network in Home (CenturyLink provided it as a DSL/Router combo). Would not connect (nor would my iPhone 4s or my wife's iPhone 4) until I accessed the router's setting and changed to broadcast on Channel 6 and then IPad connected. I suspect the only reason the iPhone were still connected to the Linksys network is that they were before I "upgraded to iOS 6. Even after 6.0.2 the iPad and both iPhones will not connect to some home networks (its random) although thye will connect to public networks e.g. McDonald's, Panera, etc.

Recently purchased iPad Mini. Downloaded iOS 6.0.1. Could not get it to connect to Home WiFi using Linksys G Router. Have another Wifi Network in Home (CenturyLink provided it as a DSL/Router combo). Would not connect (nor would my iPhone 4s or my wife's iPhone 4) until I accessed the router's setting and changed to broadcast on Channel 6 and then IPad connected. I suspect the only reason the iPhone were still connected to the Linksys network is that they were before I "upgraded to iOS 6. Even after 6.0.2 the iPad and both iPhones will not connect to some home networks (its random) although thye will connect to public networks e.g. McDonald's, Panera, etc.

AirPort Utility in Windows - cannot set 5GHz channel manually

I am trying to manually set my 5GHz channel to something other than automatic. I change it to
and click the update button. The router restarts and my changes do not stick. It now shows
The 2.4GHz channel can be modified but not the 5GHz. Anyone have any ideas?
Thanks.

So are you saying that it does not work with v6 on an Apple product either?
That is the info I have at this point in time. I have totally avoided AC models.. I think they are poor cf the same chipset models available from Asus or Netgear that have real GUI setups with real functionality.
Is there functionality that is available in the Mac version but not in the Windows version?
The v5 utility in Mac and PC was the same functionality..
The v6 utility in Mac and never released for PC has far less functionality. Which is designed I guess to correspond to the new model Apple routers which also have less functionality. For instance there is no longer a log function you can use. Apple do not believe in functionality.. it is supposed to be as near to self setting as possible.. the ideal would be purely automatic and no airport utility. Apple are slowly working towards their nirvana.
Why has Apple neglected to update the Windows version? Looks like the Windows version 5.6.1 (Post Date: Jun 11, 2012) is a year older than the Mac version (Post Date: Jul 11, 2013).
Apple do not reveal info like this.. but my guess is they produced an iOS version so they figured if you don't have a Mac then surely you own an iphone or ipad.. if not you should buy one.

Set all channels automation parameter removed in 8?

In Logic 7 you could hold the "Control" key while changing a channel's automation parameter from volume to mute (for example) and all the channels would then display mute automation. In 8 this is no longer the case....
How do you set global automation parameters in 8??
Thanks

Shweta ,
<i>Sometimes receiver will want to execute SQL statement dynamically</i>....
How you will get the query dynamically? Ok Let me assume, consider they are sending the query through file, then its definitely possible. But u need BPM and also not sender JDBC receiver adapter instead, receiver JDBC adapter.
SQL Query File ->BPM>Synchronous send [Fetch data from DB]--->Response -
>...............
Do u think the above design will suit's ur case!!!!
Best regards,
raj.

Set B Channel ID information to Preferred in MGCP Gateway

Similar Messages

Maybe you are looking for