Set configure IPv6 to automatically as default.

I am using an iMac running Yosemite 10.10.1. Whenever I startup, get mail, or try to print a file, I have to go to system preferences > network > advanced, and set the Configure IPv6 to automatically from its default setting of off. For some reason it always goes back to the default “off” setting. Is there a way to make “automatically” the default setting? Thank you.

Automatic is the default. I think you need to reinstall Yosemite:
Reinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Also see:
Reinstall OS X Without Erasing the Drive
Choose the version you have installed now:
OS X Yosemite- Reinstall OS X
     Note: You will need an active Internet connection. I suggest using Ethernet
                 if possible because it is three times faster than wireless.

Similar Messages

  • Use System Proxy Settings - when this is selected in FF v3.6.6, does it adhere to the same local IE proxy setting? We use a pac file configured in "Use automatic configuration script."

    Does anyone know what Firefox looks at locally on the PC when the "Use System Proxy Settings" setting is selected? It appears to be the default setting, recently changed from "No Proxy" of versions past...
    Our company uses a pac file specified in IE under "Use automatic configuration script" - with this new default, does it adhere to the same setting in:
    [HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Internet Settings]

    I may be wrong but I think that the "Use System Proxy Settings" makes sense only on Linux and generally speaking "other OSes". As far as I know there is no generic proxy settings in Windows operating system.
    The one I know is in the registry part of Internet Explorer.
    So in my understanding in Windows, Use System Proxy Settings = No Proxy

  • Safari was very slow in opening up Google sites.  I found a discussion thread that suggested changing the "Configure IPv6" setting to "Off" in the System Preferences, Network, Advanced, TCP/IP section.  That seems to work well.  Are there any risks?

    Safari was very slow in opening up Google sites.  I found a discussion thread that suggested changing the "Configure IPv6" setting to "Off" in the System Preferences, Network, Advanced, TCP/IP section.  That seems to work well.  Are there any risks to leaving the Configure IPv6 setting to Off?

    Nope. You can always reverse that if you choose.

  • Problem in configuring IPv6 interface with default  Router lifetime.

    I'm facing Problem in configuring IPv6 interface with default
    Router lifetime through a router advertisement.
    I'm also see an unusual behavior that even after configuring accept_rtadv=0,
    the ipv6 address is configured.
    Please help in out .

    Mac OS 9 does not support IPv6. While you can have IPv6 on your network, a Macintosh running Mac OS 9.2.2 or earlier cannot make connections to services using this network protocol.
    To use IPv6 on a Macintosh, you need Mac OS X 10.1 or later (as far as I know).
    —tonza

  • Users are not able to use Outlook 2010 to view free/busy information and cannot set Out Of Office automatic reply

    Hi All,
    Please help me.
    I have an issue where users are not able to use Outlook 2010 to view free/busy information and cannot set Out Of Office automatic reply. But they are can set Out Of Office automatic reply from OWA. My exchange server is Ms Exchange 2010.
    The test E-mail AutoConfiguration failed with this error:
    Autodiscover to https://mydomain.com/autodiscover/autodiscover.xml starting
    GetLastError=12175; httpStatus=0.
    Autodiscover to https://mydomain.com/autodiscover/autodiscover.xml Failed (0x800C8203)
    Autodiscover to https://autodiscover.mydomain.com/autodiscover/autodiscover.xml starting
    GetLastError=12007; httpStatus=0.
    Autodiscover to https://autodiscover.mydomain.com/autodiscover/autodiscover.xml Failed (0x800C8203)
    Local autodiscover for mydomain.com starting
    Local autodiscover for mydomain.com Failed (0x8004010F)
    Redirect check to http://autodiscover.mydomain.com/autodiscover/autodiscover.xml starting
    Srv Record lookup for http://autodiscover.mydomain.com/autodiscover/autodiscover.xml Failed (0x80072EE7)
    Srv Record lookup for mydomain.com starting
    Srv Record lookup for mydomain.com Failed (0x8004010F)
    Any idea?
    Thanks,
    Pieter

    OK.
    Please follow this step.
    1. As you said you are in coexistence step , so for now all endpoint already point to Exchange 2010 right?
    2. Check legacy owa redirect that you already configure
    3. In Exchange 2010 , Make sure that you already configure "Autodiscoverinternaluri" by this command set-clientaccessserver -identity "servername" -autodiscoverinternaluri
    https://autodiscover.domain.com/autodiscover/autodiscover.xml. and don't forget to create autodiscover record in DNS
    4. in Exchange 2010 , Make sure that you already configure "EWS" path by this command set-webservicesvertualdirectory -identity "XXX\Default web site name" -internalurl
    https://yourinternalurl/EWS/Exchange.asmx -externalurl https://yourexternalurl/EWS/Exchange.asmx
    5. don't forget to replicate freebusy from Exchange 2003 to Excahnge 2010 via public folder.
    You error look like client cannot get autodiscover process please check it again.

  • Network Settings: Configure IPv6, On or Off?

    Hello everyone.
    A while back I read on MacFixIt that some experience slowness in internet connection after 10.4.5 update, and it suggested turning 'off' the IPv6 setting inside the Network settings, found at the bottom of it.
    I was curious and click the button to find my 'Configure IPv6' was set to 'Automatic'.
    In any case, I did not experience any drastic change in the speed of my internet connection after the 10.4.5 update; and I actually turn off my IPv6 setting, which again no so much drastic change in speed.
    So the question is: Should I leave it on at 'Automatic' or turn it off?
    Info: My iMac is connected directly (wired) to my cable modem.
    Thanks and cheers

    I've tried it on & off & didn't notice any difference at all.
    But - if you need to use stuffit expander - it'll crash on starting stuffit unless IPv6 is enabled. found that on stuffits forum after wondering why it suddenly wouldn't work.

  • How to Set/Configure Manual GPRS Setting with Asha...

    Can any one help me with to set manual GPRS setting for Nokia Asha 200.
    I want to change the GPRS setting, But there is no option for "Edit" or "New" (Configuration)
    Thanks
    Ricky

    Hi framor, 
    Welcome to Nokia discussions board! 
    In order to set up an internet access point for your Nokia Asha 200, please follow the steps below:
    Menu
    Settings
    Configuration
    Personal Settings
    Add (or add new)
    Internet
    Edit account name > input operator’s settings
    Select “No” in use “preferred access point”
    Access point settings
    Bearer settings
    Edit “packet data access point” > input operator’s settings
    Back 4 X
    Default config. Settings: select “personal configuration”, and click on “by default”
    By default in apps: select “yes”
    Please ask your operator to send you an SMS for automatic set up. If you have an issue connecting to the internet, you may set up the access point manually as described above.
    For further support on internet acces on your device, please contact your operator.
    Let us know how you get on and feel free to post any other questions you may have.
    Regards,
    Astra2025
    Press the 'Accept Solution' icon if I have solved your problem, Kudos my post if my advice has helped you!

  • How configure GR/IR Automatic Clearing

    Hi Friends,
    How I configure GR/IR Automatic Clearing. Whatu2019s the path in SPRO t-code. Please help me.
    Regards,
    Hemant Maurya

    Hi,
    To set up automatic clearing, follow the path below:
    Financial Accounting-> General Ledger Accounting -> Business Transactions-> Open Item Clearing -> Prepare Automatic Clearing
    Here you can define rules for matching documents while clearing the GR/IR or any other account.  You have the option of setting 5 matching criteria.
    As an example, you can use the following 2 criteria for matching in GR/IR account:
    EBELN (PO number)     EBELP (PO Line item).
    Cheers.

  • How do I set Firefox 4 to automatically start in 16-bit mode?

    Certain web sites I use daily require Firefox 4 to be started in 16-bit mode. How do I set Firefox 4 to automatically start in 16-bit mode?

    Do you mean 32 bit mode as opposed to the default 64 bit mode?
    # Close Firefox
    # Open the Applications folder in Finder
    # Right click or control-click the Firefox.app icon
    # Select "Get Info"
    # Select or Deselect "Open in 32-bit mode"
    # Close the "Firefox Info" window
    # Restart Firefox

  • Failed to configure IPv6 interface(s): eri1 - how to debug?

    I have a problem configuring the second network interface for IPv6 under Solaris 10. The first interface, eri0, is configured and works fine. The second one, eri1, has a link-local address but no global address. Both links are up and working, I can ping eri1 via IPv4 (10.0.1.9) from an external host.
    netra / $ ifconfig -a6                                                                                                                                       
    lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
            inet6 ::1/128
    lo0:1: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
            zone wibble
            inet6 ::1/128
    lo0:2: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
            zone foobar
            inet6 ::1/128
    eri0: flags=2000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 2
            inet6 fe80::203:baff:fe0b:fd4b/10
            ether 0:3:ba:b:fd:4b
    eri0:1: flags=2080841<UP,RUNNING,MULTICAST,ADDRCONF,IPv6> mtu 1500 index 2
            inet6 2001:0:0:1:203:baff:fe0b:fd4b/64
    eri0:2: flags=2000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 2
            zone wibble
            inet6 2001:0:0:1::4/64
    eri0:3: flags=2000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 2
            zone wibble
            inet6 fe80::213:a9ff:fe80:43c0/10
    eri0:4: flags=2000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 2
            zone foobar
            inet6 2001:0:0:1::3/64
    eri0:5: flags=2000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 2
            zone foobar
            inet6 fe80::213:a9ff:fe80:43bf/10
    eri1: flags=2004841<UP,RUNNING,MULTICAST,DHCP,IPv6> mtu 1500 index 3
            inet6 fe80::203:baff:fe0b:fd4b/10
            ether 0:3:ba:b:fd:4bMy setup is the same for both interfaces:
    - empty files /etc/hostname6.eri0 and /etc/hostname6.eri1
    - both NICs connected to the same switch, with a L2-adjacent IPv6 router.
    Last messages from the serial console are:
    Failed to configure IPv6 interface(s): eri1
    SUNW,eri0 : 100 Mbps full duplex link up
    Hostname: netra
    SUNW,eri1 : 100 Mbps full duplex link up
    (at this point, I issued 'svcadm restart network/physical')
    Failed to configure IPv6 interface(s): eri1
    Aug 30 16:59:29 netra in.ndpd[259]: phyint_init_from_k: SIOCLIFGETND (interface eri1): No such process
    Aug 30 16:59:29 netra last message repeated 1 time
    Aug 30 16:59:29 netra in.ndpd[259]: Interface eri1 has been removed from kernel. in.ndpd will no longer use it
    Do you have any ideas? Where to look?
    Maciej
    Edited by: automatthias on Aug 30, 2008 9:12 AM
    Edited by: automatthias on Aug 30, 2008 9:12 AM

    Thank you for the answer! I've found an option 'local-mac-address?' (the question mark is a part of the parameter name) in the 'ok' prompt.
    More info for next generations:
    1. Get to the 'ok prompt' (OpenBoot prom)
    2. Type 'printenv' to see the current settings, look for 'local-mac-address?'
    3. Set the parameter to 'true': 'setenv local-mac-address? true'
    4. Type printenv again to see if the option was actually changed
    This option is also described in Gentoo OBP reference:
    http://www.gentoo.org/doc/en/gentoo-sparc-obpreference.xml
    Thanks!
    Maciej

  • JMS Adapter - Set Additional JMS Parameters or Replace Default Settings

    Hi colleagues,
    We are using PI/XI 7.0 (SP 12).
    In trying to set up a Communication Channel using JMS Adapter to connect to Oracle AQ, I do not see the checkbox "Set Additional JMS Parameters or Replace Default Settings" , nor is the table for the parameters / value visible.
    We have deployed the driver file as described in the How-to- guide: How To Install and Configure External Drivers for JDBC & JMS Adapters
    [http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/f04ce027-934d-2a10-5a8f-fa0b1ed4d88f?quicklink=index&overridelayout=true]
    In setting up the Communication Channel so far:
    Type: Sender
    Transport Protocol: Access JMS Provider Generically
    Message Protocol:  JMS 1.x
    Adapter Engine:      Integration Server
    After this I expect to see the checkbox  "Set Additional JMS Parameters or Replace Default Settings", but it is not there.
    Therefore I am not able to select it in order to enter parameters like:
    JMS.QueueConnectionFactoryImpl.classname
    JMS.QueueConnectionFactoryImpl.method.setHostName
    JMS.QueueImpl.classname
    JMS.QueueImpl.constructor.... etc
    Can someone please share if this because we are on too low SP or do we need to do something additional before it becomes visible?  Is this a feature that only became available as of PI/XI 7.0 SP 13 or 14 ?
    I checked both Sender and Receiver channel type, and it does not appear for both.
    Thanks & Cheers,
    Jodie

    Hi experts,
    We are using PI 7.1 and I've set up a communication Channel using JMS Adapter to send
    messages to a Sonic MQ queue.
    I need to send some values as JMS parameters, two of which are constants and two are values
    from the Sender message. I tried defining and setting up the parameters with constants values
    in the Communication Channel under the Advanced tab by selecting the check-box
    set Adapter-specific Message Attributes as follows:
    Name     TYPE
    ContentType     String
    ReturnValue     boolean
    Name     VAlue
    Contenttype     CompanyCode
    ReturnValute     true
    This however lead to an error in the Adapter Engine (RWB).
    My problem is:
    1. Can anyone please instruct me as to how to go about defining and setting up
       additional JMS parameters?
    2. How to go about defining/setting up variables that will get their values from
       the sender message?
    Thanks & Cheers,
    Joe

  • How to set the show properties as  a default in KM

    Hello All,
    I am trying to upload the documents in KM repository using File-> Upload. If I click this Upload button, it will open a new window, it will show (show properties) this properties. But I want this one as default. Can any one help to set the (show properties) as a default? 
    Thanks in  Advance.

    Hi Gowsika,
    I'm sorry, but you seem not to get my explanation.
    First, there is no such "switch" for "Show Properties" or "Hide Properties", and there is also not Resource Type "Show Properties". It is hardcoded in the UICommand "upload" (so in the Screenflow implemented by com.sapportals.wcm.rendering.uicommand.cm.UIUploadCommand), that if the ResourceType "normalrt" (http://sap.com/xmlns/cm/framework/normal-resource-type) displayed "Normal Document" is selected, you will see the "Show Properties" link. Only by changing the implementation of this UICommand you could change this behavior, but it's not recommended because you have to make sure on upgrades that you don't overwrite it again.
    So again my suggestion:
    1. Go to KM->CM->Configuration->CM->Global Services->Resource Types
    2. Duplicate the Resouce Type "normalrt" changing:
      Name: my_normalrt
      Resource Type ID: http://sap.com/xmlns/cm/framework/my-normal-resource-type
    3. Go to KM->CM->Configuration->CM->Global Services->Property Structures->Property Structures
    4. Duplicate "DefaultPropertiesStructure" changing:
      Name: My_DefaultPropertiesStructure
      Resource Types: http://sap.com/xmlns/cm/framework/my-normal-resource-type
      Structure Items: "Input_here_your_properties_and_property_groups"
    BTW: If you want to have the same properties as in DefaultPropertiesStructure you might be obligated to remove some of them from the original Property Structure.
    5. Go to KM->CM->Configuration->CM->User Interface->Commands->UI Commands
    6. Duplicate "new_file" changing:
      Alias: my_upload
      Parameters: ResourceType=http://sap.com/xmlns/cm/framework/my-normal-resource-type,standalone=true
    7. Go to KM->CM->Configuration->CM->User Interface->Commands->UI Command Groups
    8. Edit AdminNewResourceGroup by renaming upload to my_upload in the "Commmand List" parameter.
    BTW: It's advisable to duplicate the whole Command Group and use it in your Layout Set and not to change the standard configuration, but I will not describe the whole process here
    9. Now go to KM Content and use the menu Folder->New...->Upload
    Hope this helps,
    Robert

  • Set Reader to NOT be the default pdf viewer

    During an msi install how do I set Reader to NOT be the default pdf viewer?

    Just to add to this question:
    On Mac OS 10.5, using Acrobat 8 Professional, every time Acrobat Pro starts up, I get the question "Adobe Acrobat 8 Professional.app is not currently configured to be the default application for PDF files.  Would you like to make PDF files open with Adobe Acrobat Professional.app instead of Preview.app?"
    My answer is "No," but my preference in this matter is not retained.  I get the question every single time I launch Acrobat Pro.  Where is the button labeled "And don't ask me again!"  ?
    I have combed through the Preference dialog and not been able to find any setting that seems related to this.  To be clear, I am not talking about what happens when I double-click a PDF file in the Finder.  I'm talking about what happens when Acrobat 8 Professional is opened directly.
    Thanks.

  • Cisco 1130 ag - The system is not configured to boot automatically

    I have a problem on a 1131ag Access point on recycle it stops and makes me maunually type BOOT at the ap: prompt
    ----------VVVVVVVVVVVVV----------------
    ap: Xmodem file system is available.
    flashfs[0]: 282 files, 13 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 15998976
    flashfs[0]: Bytes used: 9497088
    flashfs[0]: Bytes available: 6501888
    flashfs[0]: flashfs fsck took 33 seconds.
    Base ethernet MAC Address: 00:12:d9:2b:39:0c
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ethernet link up, 100 mbps, full-duplex
    Ethernet port 0 initialized: link is up
    The system is not configured to boot automatically. The
    following command will finish loading the operating system
    software:
    boot
    C1130 Boot Loader (C1130-BOOT-M) Version 12.3(2)JA, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Mon 08-Nov-04 12:40 by ccai
    [I have to type "boot" here to load system]
    ap: boot
    Loading "flash:/c1130-k9w7-mx.123-7.JA4/c1130-k9w7-mx.123-7.JA4"...#############
    File "flash:/c1130-k9w7-mx.123-7.JA4/c1130-k9w7-mx.123-7.JA4" uncompressed and 0
    executing...
    Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706
    Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.3(7)JA4, RELEASE )
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by Cisco Systems, Inc.
    Compiled Tue 05-Sep-06 14:14 by alnguyen
    Image text-base: 0x00003000, data-base: 0x00683F60
    Initializing flashfs...
    flashfs[1]: 282 files, 13 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 15998976
    flashfs[1]: Bytes used: 9497088
    flashfs[1]: Bytes available: 6501888
    flashfs[1]: flashfs fsck took 4 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    [Legal notes removed]
    cisco AIR-AP1131AG-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8.
    Processor board ID FOC08514JMF
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from power-on
    1 FastEthernet interface
    2 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:12:D9:2B:39:0C
    Part Number : 73-8962-06
    PCA Assembly Number : 800-24818-06
    PCA Revision Number : B0
    PCB Serial Number : FOC08514JMF
    Top Assembly Part Number : 800-25544-01
    Top Assembly Serial Number : FTX0909T049
    Top Revision Number : A0
    Product/Model Number : AIR-AP1131AG-A-K9
    -----------^^^^^^^^^^^^------------------
    I have already performed the ap: set BOOT etc commands a dozen times with the same results.
    It says: The system is not configured to boot automatically.
    I've been trying to get this one going for 4 months now..it was knocked out during a power outage while upgrading it.

    I didn't know how to get to global configuration mode - I did manage to get there with a bit of guess work.
    You use AP: Boot
    Let it go through the boot process then at the AP> prompt, [enable] priviledged command set, type in password.
    At AP# prompt type [config] then press enter for [terminal] at AP#[config] type NO BOOT MANUAL press [Enter] key and reboot AP.
    Question...Do I have to use a WRITE command to write the configuration to CMOS?
    I did just play it safe.

  • Setting the allowaccess option as the default in xlock

    Hi,
    I was wondering if someone could point me in the right direction with a problem I�m having with Solaris 10 on a distributed system and the standard xlock application.
    As I stated we�re running an application on a distributed system where we want to have the ability to lock down the operational processor with the command �xlock� and also have the ability to start and stop the application from another system while the processor is locked. This can be accomplished by running the command �xlock �allowaccess� on the operational processor.
    My question, is there a way to set the �-allowaccess� option in user defaults or some other place so when the �xlock� command is executed it automatically sets the �-allowaccess� option?
    I�ve already accomplished it in a script, but would prefer to do it within the system.
    Any ideas would be greatly appreciated.
    Thanks

    I figured it out, it was just a matter of setting "alias -tx xlock -allowaccess xlock" in the .profile

Maybe you are looking for